LM324KPWR - Quad 30V 1.2MHz Op Amp | Texas Instruments
MPN: LM324KPWR ✓ ActiveLM324KPWR Overview
An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to control an output voltage. The LM324 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Its four channels share a positive supply, negative supply, and ground reference, making it useful where several independent low-frequency analog stages are required in the same board area.
The principal features include four amplifiers per package, a 1.2 MHz gain-bandwidth product, operation from a single supply or dual supplies, a 30 V maximum total supply rating, and 2 kV ESD protection. These characteristics suit general-purpose signal conditioning rather than precision or high-speed instrumentation. The quad organization also reduces component count and simplifies routing when one board section contains four similar low-frequency channels.
Each amplifier uses differential inputs, an output stage, bias compensation, and internal frequency compensation. The common design is intended for stable operation with feedback networks that define closed-loop gain. Because this is a general-purpose amplifier, input offset, input bias current, output-current capability, slew rate, and common-mode limits should be checked against the exact signal levels and load conditions before finalizing a design.
Typical uses include sensor-signal conditioning, low-frequency active filters, audio preamplification, comparators with suitable feedback, DC summing and difference stages, and general buffer or gain stages. The 14-pin TSSOP is appropriate for compact industrial, instrumentation, consumer, and embedded-control equipment where four analog channels are preferable to separate single or dual amplifier packages.
Layout and stability remain the primary implementation considerations. Keep input and feedback traces short, place compensation or bypass components close to their associated pins, and maintain a common ground reference across all four channels. Avoid long unprotected inputs and place external input clamps where exposed connectors can carry electrostatic discharge. Confirm the selected channel’s input and output swing against the intended supply rails.
This page consolidates the exact package, electrical headline ratings, drop-in alternatives, comparison parameters, and practical design guidance for LM324KPWR. It helps engineers identify the correct TI orderable MPN and assess whether the quad general-purpose amplifier meets a circuit’s voltage, bandwidth, ESD, footprint, and sourcing requirements.
Drop-in alternatives for LM324KPWR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM324KPWR (same form factor and footprint) — differing in Amplifier Type, Package, Supply Configuration, Maximum Supply Voltage, RoHS Status.
LM324APWR
✅ Drop-InContact for price
View Datasheet →LM324KAPW
✅ Drop-InContact for price
View Datasheet →LM324PWRG3
✅ Drop-InContact for price
View Datasheet →LM324PWRE4
✅ Drop-InContact for price
View Datasheet →LM324PWRG3
✅ Drop-InContact for price
View Datasheet →LM324KPWR Maximum Ratings & Electrical Characteristics
| Amplifier Count | 4 circuits |
| Device Type | Quad general-purpose operational amplifier |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| ESD Protection | 2 kV |
| Package | 14-pin TSSOP |
| Package Width | 4.40 mm |
| Mounting Type | Surface mount |
| Number of Inputs and Outputs | 8 inputs and 4 outputs |
| Supply Configuration | Single or dual supply |
LM324KPWR Pin Configuration
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | IN1- — Amplifier 1 inverting input |
| Pin 3 | IN1+ — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | IN2+ — Amplifier 2 non-inverting input |
| Pin 6 | IN2- — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | IN3- — Amplifier 3 inverting input |
| Pin 10 | IN3+ — Amplifier 3 non-inverting input |
| Pin 11 | V+ — Positive supply connection |
| Pin 12 | IN4+ — Amplifier 4 non-inverting input |
| Pin 13 | IN4- — Amplifier 4 inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Typical Applications
LM324KPWR is suitable for 6 applications: Industrial Sensor Signal Conditioning, Audio Preamplification, Active Filter and Control, Battery-Powered Monitoring, LED Driver and Interface Circuits, Power Supply Feedback and Sequencing.
Industrial Sensor Signal Conditioning
The LM324KPWR fits four-channel industrial sensor conditioning when the signals fall within its low-frequency general-purpose performance class. Its four amplifiers can implement buffering, fixed or variable gain stages, active filters, and signal summing while sharing the same 30 V-class supply arrangement. The 1.2 MHz gain-bandwidth product is suitable for transducers with moderate bandwidth rather than fast sensor front ends. Keep high-impedance sensor wiring short, bypass the shared supply pins locally, and check input bias current when sensor-source impedance is high.
Recommended
Audio Preamplification
The LM324KPWR can provide inexpensive, low-frequency audio preamplification when modest bandwidth and general-purpose precision are acceptable. Its 1.2 MHz gain-bandwidth product supports audio-band amplification, while four channels allow stereo and monitor paths to share one package. The common supply arrangement simplifies routing, although each channel still requires suitable input and feedback networks. For low-noise or high-fidelity designs, verify input offset voltage, input bias current, output swing, and load capability against the Texas Instruments manufacturer datasheet.
Recommended
Active Filter and Control
The LM324KPWR is suitable for low-frequency active-filter and control applications built around four similar amplifier channels. Its 1.2 MHz gain-bandwidth product provides more bandwidth than strictly required by many audio, control, and instrumentation filters, while the quad package reduces board area. Compensation is internal, so closed-loop gain and stability should follow the manufacturer’s recommended circuits. Avoid using the device as a high-speed comparator or PWM edge-rate amplifier without checking slew rate, saturation recovery, and output-current behavior.
Recommended
Battery-Powered Monitoring
The LM324KPWR can form part of battery-powered monitoring equipment because it combines four amplifier channels in one compact TSSOP package. The shared supply pins simplify power routing, while operation from a single supply supports systems where the signal must remain above ground. The 30 V maximum supply rating provides headroom, but actual minimum operating voltage and quiescent current must be checked in the manufacturer datasheet. Use low-leakage input biasing and confirm the output-swing limits at the selected supply and load.
Recommended
LED Driver and Interface Circuits
The LM324KPWR can implement error amplifiers, current-control loops, and interface stages for LED systems operating at moderate bandwidth. Its four channels allow a controller, feedback amplifier, and auxiliary signal-conditioning stages to be consolidated. Because the device is a general-purpose amplifier rather than a dedicated LED driver, output-current capability, output swing, and thermal conditions must be evaluated carefully. Select external transistor or driver stages when the LED load exceeds the amplifier’s output capability or when faster response is required.
Recommended
Power Supply Feedback and Sequencing
The LM324KPWR can serve as a general-purpose feedback amplifier in linear or supervisory power-control circuits. Its four channels support error amplification, rail comparison, current-sense amplification, and sequencing logic interfaces when all signals remain inside the common-mode and output-swing limits. The 30 V-class supply capability is useful for monitoring higher-voltage rails, but the amplifier is not isolated and must not exceed its absolute supply rating. Keep feedback-node copper compact and provide a stable reference reference point for all channels.
Recommended
Recommended Products Summary
Engineering reference data for LM324KPWR — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM324APWR | LM324KAPW | LM324PWRG3 | LM324PWR | LM324PWRG3 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor | ROHM Semiconductor |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP-BJ | 14-TSSOP-BJ |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Device Classification | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
Key Differentiators
- Improved ESD protection within a compact quad package (vs LM324APWR)
- Four general-purpose channels in one TSSOP (vs LM2902KNS)
- Matched 1.2 MHz general-purpose performance class (vs LM324PWR)
- Single-package channel consolidation (vs LM2902KNS)
Design Notes
Place the supply-bypass capacitor close to pins 4 and 11, and keep the high-impedance input traces at pins 2, 3, 5, 6, 9, 10, 12, and 13 short. Route feedback components directly to their associated amplifier pins so parasitic capacitance does not destabilize the closed-loop response. Use the manufacturer package drawing to confirm pin-one orientation and maintain the 14-pin TSSOP land pattern.
Do not treat the 30 V maximum supply rating as a recommended operating point. Verify minimum and maximum operating supply voltage, common-mode input range, output swing, output current, and slew rate for the selected gain and load. A four-amplifier package also multiplies total supply demand, so calculate the worst-case channel load and thermal condition before finalizing the power-supply design.
Keep sensor wiring and feedback nodes away from switching nodes, high-current return paths, and digital clock traces. If the source impedance is high, the amplifier input bias current can produce a DC error; use the manufacturer’s input-bias-current limit to estimate that error and add guarding or biasing where necessary. External ESD protection is still appropriate for externally accessible inputs despite the LM324K family’s improved 2 kV ESD rating.
Decouple each supply rail locally and use a supply regulator with adequate transient response for all four channels. Verify startup behavior, output saturation recovery, and load-drive margin rather than relying only on the 1.2 MHz gain-bandwidth product. If any channel can drive a capacitive load, check the recommended isolation resistance and load values in the manufacturer application guidance.
Compliance Information
Compliance status requires confirmation from the current manufacturer documentation for the exact LM324KPWR orderable part number.