LPC11U67JBD64551 - 50MHz Cortex-M0+ MCU | NXP
MPN: LPC11U67JBD64551 ✓ ActiveLPC11U67JBD64551 Overview
An ARM Cortex-M0+ microcontroller is a reduced-instruction-set processor core integrated with memory, peripherals, and communication interfaces on one semiconductor device. The Cortex-M0+ hierarchy places the part within embedded processors, microcontrollers, and the broader semiconductor category. Its 32-bit architecture and 50 MHz maximum clock rate provide useful processing performance for control tasks while retaining a compact, energy-conscious design footprint.
The LPC11U67JBD64551 provides 128 KB of flash memory, organized as 128K by 8 bits, for firmware storage. Its 64-LQFP package supports surface-mount assembly and exposes the device's interface pins on a standardized 10 mm by 10 mm footprint. These characteristics make the MCU suitable for embedded control boards, sensor nodes, industrial modules, and compact consumer devices that require more program storage than a small entry-level microcontroller.
The LPC11U67 designation identifies the device within the LPC11U family, while the full ordering code LPC11U67JBD64551 identifies the exact configuration offered for sourcing. The listing identifies the component as an NXP USA Inc. LPC11Uxx microcontroller with an ARM Cortex-M0+ core, single-core architecture, 50 MHz operating frequency, 128 KB flash, and 64-LQFP package. Detailed memory-map, peripheral, electrical, and programming information should be confirmed against the NXP device documentation before a new design is released.
Typical applications include low-power sensor hubs, building and industrial control modules, compact motor-control boards, communications equipment, and embedded accessories. The 128 KB flash capacity allows more application code and configuration data than very small microcontroller variants, while the 10 mm by 10 mm LQFP package simplifies inspection, hand rework, and prototype-board assembly compared with leadless packages.
Designers should treat the LPC11U67JBD64551 as a surface-mount embedded device rather than a simple logic component. Confirm the exact pin assignment, peripheral availability, voltage limits, clock configuration, programming interface, decoupling requirements, and exposed-pad requirements in the official device documentation. Keep sensitive programming and debug connections accessible, and follow the recommended decoupling and layout patterns to preserve signal integrity and reliable startup.
This product page consolidates the exact orderable MPN, source-backed core and package information, sourcing guidance, and practical replacement considerations. It also distinguishes the standard LPC11U67 ordering options from unrelated Cortex-M0+ devices, helping engineers avoid cross-platform substitutions that may fit a similar application but do not preserve the target's package, pinout, firmware environment, and peripheral configuration.
Drop-in alternatives for LPC11U67JBD64551 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LPC11U67JBD64551 (same form factor and footprint) — differing in Flash Memory, Product Type.
LPC11U67JBD64E
✅ Drop-InContact for price
View Datasheet →LPC11U67JBD64E
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →LPC11U67JBD64X
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
LPC11U67JBD64XI
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
LPC11U67JBD645
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
LPC11U67JBD64551 Maximum Ratings & Electrical Characteristics
| Product Type | 32-bit single-core microcontroller |
| Processor Core | ARM Cortex-M0+ |
| Architecture | 32-bit ARM |
| Maximum CPU Frequency | 50 MHz |
| Flash Memory | 128 KB (128K x 8 bits) |
| Core Count | 1 core |
| Package | 64-LQFP (10 mm x 10 mm) |
| Pin Count | 64 pins |
| Mounting Type | Surface mount |
LPC11U67JBD64551 64-lqfp (10 mm x 10 mm) Pin Configuration Guide
Pin configuration for LPC11U67JBD64551 (64-lqfp (10 mm x 10 mm) package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for LPC11U67JBD64551.
Refer to the datasheet for full pin configuration.
Typical Applications
LPC11U67JBD64551 is suitable for 6 applications: Industrial Sensor Hub, Smart Building Controller, Compact Motor-Control Module, IoT Communications Gateway, Consumer Appliance Interface, Portable Measurement Device.
Industrial Sensor Hub
The LPC11U67JBD64551 fits compact sensor-hub controllers that acquire measurements, filter data, and communicate results over a local serial interface. Its 50 MHz ARM Cortex-M0+ core provides ample instruction throughput for typical acquisition, thresholding, and protocol tasks, while 128 KB of flash stores application firmware, calibration tables, and configuration data. The 10 mm by 10 mm 64-LQFP package also permits a conventional surface-mount layout with accessible perimeter pins for programming and service connectors.
Recommended
Smart Building Controller
The LPC11U67JBD64551 is suitable for building-control modules that combine inputs, local logic, and status communication. A 50 MHz Cortex-M0+ processor can execute event handling and control routines, and the 128 KB flash capacity accommodates application code and configuration parameters without relying on external program memory. Its 64-LQFP format supports automated assembly and inspection, while the exposed perimeter provides straightforward routing for serial communications, sensing interfaces, and logic-level control signals.
Recommended
Compact Motor-Control Module
The LPC11U67JBD64551 can serve as the supervisory controller in a compact motor-control or actuator module. The 50 MHz Cortex-M0+ core is appropriate for executing state machines, interpreting commands, and coordinating protection logic, while 128 KB of flash provides room for control algorithms and fault-handling routines. The 64-LQFP package leaves visible pins on all four sides, making power, ground, communications, and discrete control connections straightforward to route on a multilayer board.
Recommended
IoT Communications Gateway
The LPC11U67JBD64551 fits small IoT gateway boards that translate between local sensors and an upstream network connection. Its 32-bit Cortex-M0+ core running up to 50 MHz can process framing, device state, and protocol tasks, and its 128 KB flash provides sufficient storage for embedded firmware. The 10 mm by 10 mm LQFP package supports dense, serviceable assemblies, although radio and network transceivers must be implemented separately and validated alongside the MCU.
Recommended
Consumer Appliance Interface
The LPC11U67JBD64551 can manage a consumer appliance's local control panel, button inputs, indicators, and service interface. The 50 MHz processor provides ample performance for menu logic, state management, and fault reporting, while 128 KB of flash supports production firmware and calibration parameters. Its surface-mount 64-LQFP package is practical for high-volume assembly and simplifies mechanical inspection compared with a fine-pitch leadless package.
Recommended
Portable Measurement Device
The LPC11U67JBD64551 is suitable for a portable measurement instrument that combines a sensor front end with local display or communications. The 32-bit Cortex-M0+ core can execute sampling coordination and numerical processing at up to 50 MHz, while 128 KB of flash stores firmware, configuration, and calibration records. The compact 10 mm by 10 mm LQFP package supports space-constrained assemblies, and its four-sided pin arrangement eases access to programming, power, and interface connections.
Recommended
Recommended Products Summary
Engineering reference data for LPC11U67JBD64551 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LPC11U67JBD64E | LPC11U67JBD64 | LPC11U67JBD64X | LPC11U67JBD64XI | LPC11U67JBD645 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) | 64-LQFP (10 mm x 10 mm) |
| Processor Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Flash Memory | 128 KB (128K x 8 bits) | 128 KB (128K x 8 bits) | 128 KB | 128 KB | 128 KB | 128 KB |
| Architecture Width | 32-bit | 32-bit | 32-bit | 32-bit | 32-bit | 32-bit |
| Core Count | 1 core | 1 core | 1 core | 1 core | 1 core | 1 core |
| Ordering Suffix | JBD64551 | JBD64E | JBD64 | JBD64X | JBD64XI | JBD645 |
Key Differentiators
- Exact source-backed NXP ordering configuration (vs LPC11U67JBD64E)
- No stated core-performance penalty (vs LPC11U67JBD64)
- Common 64-LQFP footprint (vs LPC11U67JBD64X)
- Same-family software architecture (vs LPC11U67JBD64XI)
Design Notes
Route the MCU power rails through short, low-impedance paths and place the required bypass capacitors close to their associated supply pins according to the NXP hardware design guidance. Keep switching-regulator output and high-current return paths away from sensitive clock, programming, and communications traces. The 10 mm by 10 mm LQFP also benefits from adequate clearance around all four package sides for inspection, rework, and compatible test fixtures.
Assign the programming and debug interface early in schematic capture so the footprint, connector orientation, and signal routing can be planned without board-edge conflicts. Preserve access to reset and boot-control functions, and avoid routing fast or switching signals beneath the MCU unless the stack-up and return path have been evaluated. Confirm the 64-pin package dimensions, pin-one orientation, and land pattern from the official package drawing before releasing artwork.
Do not select an alternative solely because its order code contains LPC11U67 and 64. Verify the core frequency, flash configuration, pin assignment, temperature grade, package dimensions, exposed-pad requirements, and approved-part status for the exact suffix. Firmware image selection and qualification records may distinguish otherwise similar ordering codes, so a hardware drop-in substitution still requires an engineering change review.
Review each peripheral interface for signal-integrity and timing requirements rather than relying only on the nominal 50 MHz processor clock. Keep external clocks short, observe required setup and hold timing, and add series termination only where the complete driver and load path support it. For communications routed beyond the PCB, use appropriate protection and isolation methods and validate them across the intended voltage, temperature, and electromagnetic environment.
Compliance Information
Compliance information is not stated in the product listing or technical records and requires confirmation from the official NXP documentation.