LT1253CS8 - Dual 270MHz Current-Feedback Video Amplifier | Analog Devices
MPN: LT1253CS8 ✓ ActiveLT1253CS8 Overview
A current-feedback amplifier is a voltage-feedback amplifier architecture whose bandwidth and stability behavior can change with feedback resistance. This architecture is commonly used in video, imaging, and communications circuits that require high gain-bandwidth performance. The LT1253CS8 belongs to the broader operational-amplifier hierarchy, combining analog signal amplification with video-focused bandwidth and isolation characteristics in one integrated circuit.
The two amplifier channels are isolated except for their shared power-supply pins. According to the Analog Devices LT1253 product page, this isolation exceeds 94 dB at 5 MHz, helping reduce crosstalk when two independent video signals pass through the same package. The 270 MHz bandwidth and 250 V/µs slew rate also make the device suitable for video buffering, distribution, and gain stages operating with larger-amplitude transitions.
The LT1253CS8 accepts single or dual supplies across a ±14 V range and uses approximately 6 mA of supply current per channel under the stated operating conditions. Its 55 mA output-current capability provides suitable drive for practical video stages, while the current-feedback architecture supports the high operating frequencies associated with the family. Designers should account for amplifier input/output network values when setting gain because current-feedback amplifiers commonly use external feedback resistors.
Typical uses include professional video distribution, camera and imaging signal chains, monitor signal conditioning, broadcast equipment, and general-purpose high-speed analog amplification. The dual configuration reduces the component count compared with two separate single amplifiers and simplifies power-supply bypassing. It is particularly useful when two video channels must share a board area but still require strong isolation from one another.
For PCB implementation, place the power-bypass capacitors close to the supply pins and keep feedback and compensation components adjacent to their associated amplifier pins. Maintain short return paths for high-speed video signals, use a continuous ground reference, and avoid routing sensitive video traces adjacent to switching nodes or other high-energy timing signals. The 8-pin SO package also allows rework and inspection more easily than many fine-pitch alternatives.
This product page combines the LT1253 family architecture, 270 MHz bandwidth, 250 V/µs slew rate, supply range, isolation, and package information with practical guidance on video-signal routing, power bypassing, replacement selection, and design trade-offs. It helps engineers identify whether the dual SOIC LT1253CS8 satisfies their bandwidth, isolation, supply, and sourcing requirements before beginning layout.
Drop-in alternatives for LT1253CS8 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
LT1253CS8#PBF
✅ Drop-In📋 Reference alternative (not in catalog)
LT1253CS8 Maximum Ratings & Electrical Characteristics
| Product Type | Dual current-feedback video amplifier |
| Number of Amplifier Channels | 2 channels |
| Small-Signal Bandwidth | 270 MHz |
| Slew Rate | 250 V/µs |
| Supply Current | 6 mA per channel |
| Output Current per Channel | 55 mA |
| Supply Voltage Range | ±14 V (28 V total) |
| Differential Gain | ±5 V |
| Differential Phase | ±5° |
| Flat 0.1 dB Bandwidth | 90 MHz |
| Channel Isolation | Greater than 94 dB at 5 MHz |
| Package | 8-pin SOIC |
| Mounting Type | Surface mount |
LT1253CS8 8-pin soic Pin Configuration Guide
Pin configuration for LT1253CS8 (8-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LT1253CS8.
Refer to the datasheet for full pin configuration.
Typical Applications
LT1253CS8 is suitable for 6 applications: Professional Video Distribution, Camera and Imaging Signal Chains, Broadcast Video Processing, Video Monitor Signal Conditioning, High-Speed Analog Interface, Industrial Test and Measurement.
Professional Video Distribution
The LT1253CS8 is suitable for driving two independent video paths in professional monitoring and distribution equipment. Its 270 MHz bandwidth and 250 V/µs slew rate support rapid signal transitions, while the two channels provide greater-than-94 dB isolation at 5 MHz when they share the package. Use each channel as a gain or buffering stage and verify stability with the feedback resistor values recommended by the manufacturer. The 8-pin SOIC footprint simplifies board assembly, although each signal trace should remain short and referenced to a continuous ground plane.
Recommended
Camera and Imaging Signal Chains
The LT1253CS8 can condition high-speed analog video signals in camera, imaging, and industrial vision electronics. A 270 MHz bandwidth is well above the 90 MHz flat 0.1 dB bandwidth, allowing designers to preserve signal amplitude through the flat passband, while 250 V/µs slew rate supports large video transitions. The 55 mA output current per channel is suitable for conventional terminated video stages. Configure the current-feedback network according to the family data sheet, keep feedback components compact, and confirm that cable loading does not exceed the amplifier’s stability and output-drive limits.
Recommended
Broadcast Video Processing
The LT1253CS8 supports dual-channel broadcast video processing where bandwidth, slew rate, and channel separation are important. Its 270 MHz small-signal bandwidth and 250 V/µs slew rate provide headroom for standard-definition and higher-bandwidth composite or component-video stages, while isolation greater than 94 dB at 5 MHz reduces crosstalk between the two channels. Use separate feedback networks for each amplifier and route video signals away from switching regulators and digital timing nets. The dual SOIC package also reduces the number of power-bypass locations compared with two discrete single amplifiers.
Recommended
Video Monitor Signal Conditioning
The LT1253CS8 is appropriate for conditioning video signals that drive displays, monitors, or downstream sampling stages. The 90 MHz flat 0.1 dB bandwidth provides a useful flat-response region, and the 250 V/µs slew rate helps preserve edge information through gain and buffering operations. The dual-channel implementation is useful when a board must process related video and synchronization or control signals with separate amplifiers. Keep the output return path continuous, terminate cables according to the system impedance, and validate overshoot with the actual load because current-feedback amplifiers require the intended feedback network for stable operation.
Recommended
High-Speed Analog Interface
The LT1253CS8 can serve as a high-speed gain and buffer element in analog interfaces where the operating bandwidth exceeds the bandwidth available from general-purpose amplifiers. Its 270 MHz bandwidth, 55 mA output current per channel, and ±14 V supply range provide a combination suited to moderate-amplitude, high-speed signals. The current-feedback architecture requires careful selection of external feedback resistors and compensation values; changing those values without stability testing can affect frequency response and transient behavior. Place each feedback network close to its channel and provide local supply bypassing for repeatable video or instrumentation performance.
Recommended
Industrial Test and Measurement
The LT1253CS8 is useful in industrial video test and measurement equipment that requires two fast, isolated analog channels in a compact package. Its 270 MHz bandwidth and 250 V/µs slew rate can support pulse and video-related signal acquisition, while greater-than-94 dB isolation at 5 MHz helps limit interaction between channels. Use the common supply pins with local decoupling, maintain a continuous ground reference, and separate sensitive high-speed traces from switching circuitry. Because the LT1253 is a current-feedback amplifier, evaluate gain accuracy, overshoot, and stability using the actual external resistor values and intended source and load impedances.
Recommended
Recommended Products Summary
Engineering reference data for LT1253CS8 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LT1253CS8#PBF |
|---|---|---|
| Package | SOIC-8 | SOIC-8 - same |
| Brand | Analog Devices | Analog Devices |
| Amplifier Channels | 2 channels | 2 channels |
| Architecture | Current-feedback video amplifier | Current-feedback video amplifier |
| Small-Signal Bandwidth | 270 MHz | 270 MHz |
| Slew Rate | 250 V/µs | 250 V/µs |
| Supply Current | 6 mA per channel | 6 mA per channel |
| Output Current per Channel | 55 mA | 55 mA |
| Supply Voltage Range | ±14 V (28 V total) | ±14 V (28 V total) |
| Channel Isolation | Greater than 94 dB at 5 MHz | Greater than 94 dB at 5 MHz |
| Flat 0.1 dB Bandwidth | 90 MHz | 90 MHz |
| Lifecycle Status | Production | Production |
Key Differentiators
- Two channels with strong high-frequency isolation (vs LT1253CS8#PBF)
- Wide video bandwidth with fast edge response (vs LT1253CS8#PBF)
- Compact integration for dual video paths (vs LT1253CS8#PBF)
Design Notes
Place the LT1253CS8 feedback resistors and any compensation components adjacent to the corresponding amplifier pins. Current-feedback amplifiers depend on the external feedback network for gain and stability, so long feedback loops add parasitic inductance and capacitance that can alter frequency response. Route each channel as a compact signal path, use a continuous ground plane, and keep the feedback-side copper physically separated from the inverting input and output paths where practical.
Place supply-bypass capacitors as close as practical to the LT1253CS8 supply and ground pins. The family operates across a wide ±14 V supply range, but local decoupling remains necessary to limit supply impedance at the 270 MHz bandwidth of the amplifier. Use short, low-inductance connections between each capacitor and the package pins, and verify the capacitor type, voltage rating, and ESR implications against the stability requirements of the selected feedback network.
Keep high-speed video traces short, continuous, and referenced to an uninterrupted ground plane. The LT1253CS8's 250 V/µs slew rate can expose impedance discontinuities as reflections and overshoot even when the nominal signal bandwidth is acceptable. Avoid crossings beneath noisy power or digital timing nets, minimize stub lengths, and use controlled-termination arrangements when driving cables. Validate edge response with the intended source impedance, feedback values, cable, and load rather than relying only on a small-signal bandwidth figure.
Do not treat the quad LT1254 as a drop-in substitute for the 8-pin LT1253CS8, and do not interchange current-feedback amplifiers solely because their bandwidth ratings appear similar. The LT1254 has four channels and a different package and pinout, while alternative current-feedback devices may require different feedback resistors, compensation, supply pins, or stability margins. For a literal replacement, use LT1253CS8#PBF after confirming the required ordering suffix and lead-free termination.
Compliance Information
The LT1253CS8#PBF ordering code explicitly identifies a lead-free termination. RoHS, REACH, halogen-free, and conflict-minerals status were not stated in the manufacturer product-page snippet.