MAX232IDWG4 - 5V 120kbps Dual RS-232 Transceiver | TI
MPN: MAX232IDWG4 ✓ ActiveMAX232IDWG4 Overview
An RS-232 transceiver is an interface IC that converts logic-level signals between a digital system and RS-232 differential, bipolar signaling lines. The MAX232 belongs to the RS-232 transceiver hierarchy, where transmitters create positive or negative voltage levels for the cable and receivers detect those levels with noise tolerance. This bidirectional interface level is widely used for legacy serial ports, industrial equipment, and service connections.
The device includes two RS-232 drivers, two RS-232 receivers, and integrated charge-pump circuitry. Charge-pump capacitors of 1.0 uF support operation from a single 5 V power supply. The maximum data rate is 120 kbit/s, receiver hysteresis is 500 mV, and typical supply current is 8 mA. The Texas Instruments product page also identifies ±9 V output capability and ±2 kV ESD protection.
The MAX232 architecture allows one logic-side supply and one ground reference while producing bipolar RS-232 levels at the cable interface. Receiver hysteresis of 500 mV helps distinguish valid signal states around the transition region. The two-channel arrangement supports one full-duplex serial link using two drivers and two receivers, or two unidirectional paths when the channels are allocated independently.
Typical uses include PC serial-port emulation, RS-232 equipment interfaces, industrial-control links, test equipment, and legacy peripheral connections. The 16-pin SOIC package is suitable for conventional surface-mount PCB assembly. Because the supply side is 5 V, the circuit requires level-shifting only for the RS-232 cable side; the logic-side pins connect directly to compatible 5 V digital circuits.
Designers should place the charge-pump capacitors close to their associated pins, route transmitter outputs as interference-prone RS-232 nets, and maintain suitable return paths for the bipolar signals. The MAX232 is not a 3.3 V-only RS-232 solution, so downstream logic must be compatible with its 5 V interface or require an additional level shifter.
This page combines device specifications, verified package information, drop-in replacement guidance, interface design considerations, and practical application guidance to support faster component selection and PCB implementation.
Drop-in alternatives for MAX232IDWG4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
MAX232EESE+T
✅ Drop-InContact for price
View Datasheet →HIN232CBZ-T
✅ Drop-In📋 Reference alternative (not in catalog)
MAX232IDWG4 Specifications
| Product Type | Dual RS-232 line driver and receiver interface IC |
| Supply Voltage | 5 V |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Maximum Data Rate | 120 kbit/s |
| Transmitter Output Voltage | Approximately ±9 V |
| Receiver Input Level | ±30 V |
| Receiver Hysteresis | 500 mV |
| Typical Supply Current | 8 mA |
| Charge-Pump Capacitor Value | 1.0 uF |
| ESD Protection | ±2 kV |
| Package | 16-pin SOIC |
| Mounting Type | Surface mount |
MAX232IDWG4 16-pin soic Pin Configuration Guide
Pin configuration for MAX232IDWG4 (16-pin soic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MAX232IDWG4.
Refer to the datasheet for full pin configuration.
Typical Applications
MAX232IDWG4 is suitable for 6 applications: Industrial RS-232 Equipment Interface, Legacy PC Serial-Port Emulation, Test and Measurement Equipment, Point-to-Point Serial Console, Security and Access-Control Systems, Portable Diagnostic and Service Tools.
Industrial RS-232 Equipment Interface
MAX232IDWG4 fits legacy industrial equipment ports because it provides two RS-232 drivers and two receivers at up to 120 kbit/s from one 5 V supply. A full-duplex link can use one driver and receiver pair in each direction, while the second pair supports another unidirectional path. The approximately ±9 V output levels meet the RS-232 signaling requirement, and the receivers accept inputs up to ±30 V. This makes the device useful between a controller and older test, diagnostic, or configuration equipment while avoiding external bipolar driver stages.
Recommended
Legacy PC Serial-Port Emulation
MAX232IDWG4 can translate 5 V controller logic into ±9 V RS-232 levels for a legacy PC serial connection. Its two transmitters support bidirectional serial traffic, while its two receivers return logic-level status to the controller. The 120 kbit/s maximum rate covers many COM-port-style links, and the integrated charge pump reduces the number of external level-shifting components. Receiver hysteresis of 500 mV also improves recognition of bipolar states near the transition threshold. System designers should verify connector pin assignments, cable behavior, and the host-side UART settings.
Recommended
Test and Measurement Equipment
MAX232IDWG4 is appropriate for service-oriented test equipment that exposes an RS-232 control port. The 120 kbit/s rate supports command and response traffic typical of instrument control interfaces, while the dual-channel arrangement can carry data and hardware signaling between a controller and instrument. Its ±30 V receiver capability provides tolerance for bipolar RS-232 levels, and the single 5 V supply simplifies integration with older test-system logic. The circuit should include normal serial-port protection and cable-ground handling because the IC is an interface transceiver rather than a complete surge-protection solution.
Recommended
Point-to-Point Serial Console
MAX232IDWG4 can form the electrical interface for a point-to-point serial console between two 5 V systems. One transmitter drives the positive RS-232 signal and another drives the negative signal, while the corresponding receivers interpret the remote channel. Operating at up to 120 kbit/s provides sufficient bandwidth for command streams, diagnostic logs, and firmware-update traffic on many short links. The integrated charge pump eliminates the need for a separate RS-232 voltage converter, but cable routing, signal-ground reference, and logic-level compatibility must still be considered.
Recommended
Security and Access-Control Systems
MAX232IDWG4 can serve as the RS-232 interface in access-control readers, door controllers, and configuration tools that use a bipolar serial link. Its two transmitter and two receiver channels provide flexible allocation for a bidirectional command path or separate control and status paths. The 5 V operation is convenient for embedded equipment designed around classic 5 V UART logic, and the 120 kbit/s rate is more than adequate for short configuration messages. Deployment engineers should account for cable length, surge exposure, and grounding because these interface functions do not replace external lightning or mains transients protection.
Recommended
Portable Diagnostic and Service Tools
MAX232IDWG4 is useful in portable diagnostic tools that communicate with service equipment over RS-232. The low 5 V supply requirement supports integration with embedded control logic, and the 8 mA typical supply current helps limit overall system demand when operating from a battery-derived rail. Two driver and receiver channels can support bidirectional commands and diagnostic responses at rates up to 120 kbit/s. The tool designer should use transceiver-level logic thresholds carefully, confirm the exact operating-temperature limits, and provide appropriate isolation or protection when the connected cable leaves the enclosure.
Recommended
Recommended Products Summary
Engineering reference data for MAX232IDWG4 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MAX232EESE+T | HIN232CBZ-T |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Intersil |
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Product Type | Dual RS-232 driver and receiver | Dual RS-232 driver and receiver | RS-232 driver and receiver |
| Supply Voltage | 5 V | 5 V | 5 V |
| Number of Drivers | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 |
Key Differentiators
- Higher documented ESD protection in the same SOIC footprint (vs MAX232EESE+T)
- Documented receiver input tolerance and hysteresis (vs HIN232CBZ-T)
- Clear high-speed RS-232 capability (vs HIN232CBZ-T)
Design Notes
Place the two 1.0 uF charge-pump capacitors close to the corresponding MAX232 pins and keep their return-current paths short. Follow the capacitor configuration shown in the manufacturer datasheet, including polarity and connection to the charge-pump nodes. Place the device near the RS-232 connector so driver outputs do not run long parallel paths beneath sensitive analog or high-speed digital traces. Maintain the board outline and land pattern for the 16-pin SOIC package.
Treat both RS-232 transmitter outputs as interference-prone bipolar signals even though they use single-ended logic at the IC pins. Route TX and TXD nets away from clocks, sensor inputs, ADC signals, and external crystal circuits. Do not assume that a logic-level ground near the connector eliminates cable-borne transients. Validate the complete interface with the intended cable, connector, baud rate, and grounding arrangement because RS-232 can behave differently under unbalanced or long-cable conditions.
Confirm that every connected UART uses compatible 5 V logic levels; MAX232IDWG4 does not make 3.3 V GPIO signals safe for direct connection. Also avoid confusing the RS-232 data pins with RS-485 A/B lines, and verify TX-to-RX crossover at the connector. Before selecting a substitute, compare every pin name, charge-pump connection, external capacitor, supply limit, receiver threshold, and operating-temperature condition in the manufacturer datasheets.
Compliance Information
The available product information identifies the device as a Texas Instruments 5 V RS-232 interface IC but does not explicitly state the requested compliance statuses. JESD-2000 is referenced in the device description as the ESD comparison context.