Texas Instruments

MAX232IDWG4 - 5V 120kbps Dual RS-232 Transceiver | TI

N.º de pieza: MAX232IDWG4 ✓ Activo
5 V Vdss 8 mA Id 16-pin SOIC Package
MOQ: 1 |

MAX232IDWG4 Descripción general

The Texas Instruments MAX232IDWG4 is a 5 V dual RS-232 line driver and receiver IC supporting data rates up to 120 kbit/s, with two transmitters and two receivers in a 16-pin SOIC package. The interface IC generates approximately ±9 V transmitter output levels from a single 5 V supply and accepts receiver input levels of ±30 V.

An RS-232 transceiver is an interface IC that converts logic-level signals between a digital system and RS-232 differential, bipolar signaling lines. The MAX232 belongs to the RS-232 transceiver hierarchy, where transmitters create positive or negative voltage levels for the cable and receivers detect those levels with noise tolerance. This bidirectional interface level is widely used for legacy serial ports, industrial equipment, and service connections.

The device includes two RS-232 drivers, two RS-232 receivers, and integrated charge-pump circuitry. Charge-pump capacitors of 1.0 uF support operation from a single 5 V power supply. The maximum data rate is 120 kbit/s, receiver hysteresis is 500 mV, and typical supply current is 8 mA. The Texas Instruments product page also identifies ±9 V output capability and ±2 kV ESD protection.

The MAX232 architecture allows one logic-side supply and one ground reference while producing bipolar RS-232 levels at the cable interface. Receiver hysteresis of 500 mV helps distinguish valid signal states around the transition region. The two-channel arrangement supports one full-duplex serial link using two drivers and two receivers, or two unidirectional paths when the channels are allocated independently.

Typical uses include PC serial-port emulation, RS-232 equipment interfaces, industrial-control links, test equipment, and legacy peripheral connections. The 16-pin SOIC package is suitable for conventional surface-mount PCB assembly. Because the supply side is 5 V, the circuit requires level-shifting only for the RS-232 cable side; the logic-side pins connect directly to compatible 5 V digital circuits.

Designers should place the charge-pump capacitors close to their associated pins, route transmitter outputs as interference-prone RS-232 nets, and maintain suitable return paths for the bipolar signals. The MAX232 is not a 3.3 V-only RS-232 solution, so downstream logic must be compatible with its 5 V interface or require an additional level shifter.

This page combines device specifications, verified package information, drop-in replacement guidance, interface design considerations, and practical application guidance to support faster component selection and PCB implementation.

Alternativas directas para MAX232IDWG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

MAX232EESE+T

✅ Sustitución directa
Analog Devices
📦 16-SOIC
RS-232 transceiver · 2 · 2 · Full duplex · Up to 120 kbps · +5 V · ±15 kV human body model · EIA/TIA-232E and CCITT V.28

Consulte el precio

Ver hoja de datos →

HIN232CBZ-T

✅ Sustitución directa
📦 16-SOIC
Intersil RS-232 implementation is identified by cross-reference results as a pin-to-pin family candidate; ESD, propagation delay, and supply-current values require confirmation

📋 Alternativa de referencia (no en el catálogo)

MAX232IDWG4 Especificaciones

Product Type Dual RS-232 line driver and receiver interface IC
Tensión de alimentación 5 V
Number of Drivers 2
Number of Receivers 2
Maximum Data Rate 120 kbit/s
Transmitter Output Voltage Approximately ±9 V
Receiver Input Level ±30 V
Receiver Hysteresis 500 mV
Typical Supply Current 8 mA
Charge-Pump Capacitor Value 1.0 uF
ESD Protection ±2 kV
Encapsulado 16-pin SOIC
Tipo de montaje Surface mount

Guía de configuración de pines de MAX232IDWG4 16-pin soic

Configuración de pines para MAX232IDWG4 (encapsulado 16-pin soic). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 16-pin soic para MAX232IDWG4

No hay datos detallados de patillaje disponibles para MAX232IDWG4.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

MAX232IDWG4 es adecuado para 6 aplicacións: Industrial RS-232 Equipment Interface, Legacy PC Serial-Port Emulation, Test and Measurement Equipment, Point-to-Point Serial Console, Security and Access-Control Systems, Portable Diagnostic and Service Tools.

🏭

Industrial RS-232 Equipment Interface

MAX232IDWG4 fits legacy industrial equipment ports because it provides two RS-232 drivers and two receivers at up to 120 kbit/s from one 5 V supply. A full-duplex link can use one driver and receiver pair in each direction, while the second pair supports another unidirectional path. The approximately ±9 V output levels meet the RS-232 signaling requirement, and the receivers accept inputs up to ±30 V. This makes the device useful between a controller and older test, diagnostic, or configuration equipment while avoiding external bipolar driver stages.

🖥️

Legacy PC Serial-Port Emulation

MAX232IDWG4 can translate 5 V controller logic into ±9 V RS-232 levels for a legacy PC serial connection. Its two transmitters support bidirectional serial traffic, while its two receivers return logic-level status to the controller. The 120 kbit/s maximum rate covers many COM-port-style links, and the integrated charge pump reduces the number of external level-shifting components. Receiver hysteresis of 500 mV also improves recognition of bipolar states near the transition threshold. System designers should verify connector pin assignments, cable behavior, and the host-side UART settings.

🔧

Test and Measurement Equipment

MAX232IDWG4 is appropriate for service-oriented test equipment that exposes an RS-232 control port. The 120 kbit/s rate supports command and response traffic typical of instrument control interfaces, while the dual-channel arrangement can carry data and hardware signaling between a controller and instrument. Its ±30 V receiver capability provides tolerance for bipolar RS-232 levels, and the single 5 V supply simplifies integration with older test-system logic. The circuit should include normal serial-port protection and cable-ground handling because the IC is an interface transceiver rather than a complete surge-protection solution.

🌐

Point-to-Point Serial Console

MAX232IDWG4 can form the electrical interface for a point-to-point serial console between two 5 V systems. One transmitter drives the positive RS-232 signal and another drives the negative signal, while the corresponding receivers interpret the remote channel. Operating at up to 120 kbit/s provides sufficient bandwidth for command streams, diagnostic logs, and firmware-update traffic on many short links. The integrated charge pump eliminates the need for a separate RS-232 voltage converter, but cable routing, signal-ground reference, and logic-level compatibility must still be considered.

📺

Security and Access-Control Systems

MAX232IDWG4 can serve as the RS-232 interface in access-control readers, door controllers, and configuration tools that use a bipolar serial link. Its two transmitter and two receiver channels provide flexible allocation for a bidirectional command path or separate control and status paths. The 5 V operation is convenient for embedded equipment designed around classic 5 V UART logic, and the 120 kbit/s rate is more than adequate for short configuration messages. Deployment engineers should account for cable length, surge exposure, and grounding because these interface functions do not replace external lightning or mains transients protection.

📱

Portable Diagnostic and Service Tools

MAX232IDWG4 is useful in portable diagnostic tools that communicate with service equipment over RS-232. The low 5 V supply requirement supports integration with embedded control logic, and the 8 mA typical supply current helps limit overall system demand when operating from a battery-derived rail. Two driver and receiver channels can support bidirectional commands and diagnostic responses at rates up to 120 kbit/s. The tool designer should use transceiver-level logic thresholds carefully, confirm the exact operating-temperature limits, and provide appropriate isolation or protection when the connected cable leaves the enclosure.

What is the maximum data rate of MAX232IDWG4?
The MAX232IDWG4 supports data rates up to 120 kbit/s. According to the Texas Instruments MAX232 datasheet, its two transmitters and two receivers are optimized for RS-232/V.28 communication at rates up to 120 kbit/s. This makes the interface suitable for legacy serial-console links, industrial equipment, and peripheral connections, although cable length and system timing must also be considered when selecting the communication standard.
What type of transceiver is MAX232IDWG4?
MAX232IDWG4 is a dual RS-232 driver and receiver interface IC operating from a single 5 V supply. The Texas Instruments datasheet identifies two drivers, two receivers, integrated charge-pump circuitry, and 1.0 uF charge-pump capacitors. Its transmitter outputs reach approximately ±9 V, while the receivers support input levels up to ±30 V.
Where can I download the MAX232IDWG4 datasheet PDF?
The official Texas Instruments MAX232 product page is the preferred starting point for the manufacturer datasheet and supporting documentation. The device is also indexed in an electronic-component datasheet repository under MAX232IDWG4. Use the Texas Instruments page for the authoritative ordering information, operating limits, electrical characteristics, pin descriptions, and downloadable documentation.
Where can I find the MAX232IDWG4 pinout?
Use the pin-description table in the Texas Instruments MAX232 datasheet to assign the 16 SOIC connections. The MAX232IDWG4 provides two driver outputs, two receiver inputs, charge-pump nodes, a 5 V supply connection, and ground. Assign PCB tracks directly from that pin table because board orientation and the exposed package details must agree with the selected 16-pin SOIC footprint.
What are the key specifications of MAX232IDWG4 that engineers should know?
The principal MAX232IDWG4 specifications are a 5 V supply, two transmitters, two receivers, 120 kbit/s operation, approximately ±9 V output, ±30 V receiver input capability, 500 mV receiver hysteresis, and 8 mA typical supply current. The Texas Instruments product page additionally specifies ±2 kV ESD protection. These parameters define its use in single-ended logic-to-bipolar RS-232 interface designs.
Does MAX232IDWG4 support RS-232 from a single 5 V supply?
Yes, MAX232IDWG4 operates from a single 5 V supply and uses integrated charge-pump circuitry to generate the bipolar voltage required at the RS-232 interface. The Texas Instruments datasheet specifies 1.0 uF charge-pump capacitors and approximately ±9 V transmitter output levels. The logic-side interface still requires the connected digital circuit to use compatible 5 V signal levels.
What is the difference between MAX232IDWG4 and MAX232EESE+T?
Both devices provide a dual RS-232 interface in a 16-pin SOIC-family package, but MAX232EESE+T emphasizes stronger ESD protection. Its published comparison information identifies ±15 kV human-body-model protection, compared with the ±2 kV protection stated for MAX232IDWG4 on the Texas Instruments product page. Confirm the complete pin description and operating requirements before using it as a drop-in replacement.
Can HIN232CBZ-T replace MAX232IDWG4?
HIN232CBZ-T is a candidate for evaluation as a MAX232IDWG4 replacement because cross-reference information associates it with a pin-to-pin-compatible RS-232 family and a 16-pin implementation. However, engineers should compare the complete pin description, capacitor requirements, propagation delay, ESD rating, supply current, and operating-temperature limits in each manufacturer datasheet before approving the substitution for production.
What is the best drop-in replacement for MAX232IDWG4?
MAX232EESE+T is the closest documented drop-in candidate identified for MAX232IDWG4 because it uses the same 16-pin SOIC footprint and retains the dual-driver, dual-receiver RS-232 function. Its higher ESD rating is the principal measurable difference. Final substitution approval still requires checking every pin function, external-capacitor connection, and electrical limit against the manufacturer datasheets.
When should I choose MAX232IDWG4 over MAX232EESE+T?
Choose MAX232IDWG4 when a standard 5 V, 120 kbit/s RS-232 interface is required and the lower documented ESD rating is acceptable for the installation environment. Choose MAX232EESE+T when stronger electrostatic protection is important and its full pin and electrical characteristics remain acceptable. Both use a 16-pin SOIC-family package, so the PCB footprint can generally be reused after verification.
Is MAX232IDWG4 suitable for industrial serial interfaces?
MAX232IDWG4 is suitable for many industrial serial-interface circuits when its 5 V supply, 120 kbit/s data rate, and ±30 V receiver input range satisfy the system requirements. According to the Texas Instruments datasheet, the device supports a single 5 V supply and includes integrated charge-pump circuitry. Industrial qualification also depends on the specified operating-temperature range and the ESD environment, which should be checked against the complete device documentation.
How much current does MAX232IDWG4 consume?
MAX232IDWG4 has a typical supply current of 8 mA. The Texas Instruments MAX232 datasheet lists this value for the 5 V-operated device, while also identifying the integrated charge-pump arrangement that generates approximately ±9 V at the transmitter outputs. Actual system consumption varies with operating conditions, load activity, and the external charge-pump capacitors.
Can MAX232IDWG4 connect to a 3.3 V microcontroller?
MAX232IDWG4 is not inherently a 3.3 V-logic-compatible RS-232 transceiver because its specified supply is 5 V and its logic-side interface is intended for compatible 5 V signals. A 3.3 V microcontroller can be connected only when its TX, RX, and control levels are properly translated, or when a dual-supply RS-232 transceiver family with 3.3 V-compatible logic is selected instead. Review every logic-side voltage threshold before making the connection.
Where to buy MAX232IDWG4 online?
Use the Request a Quote form on this page to request MAX232IDWG4 availability, current lead time, and order details without relying on a static listing. The manufacturer and distributor pages associated with this part can also help confirm package, lifecycle, and ordering information. XAIPART will provide a current quotation for the exact MAX232IDWG4 MPN through the form.
What is the price of MAX232IDWG4?
A current price for MAX232IDWG4 should be requested through the Request a Quote form on this page because commercial pricing and inventory can change with market conditions and order quantity. The form allows the exact manufacturer part number, package, and requested quantities to be included in the inquiry, helping avoid confusion with related MAX232 order codes.
What is the lead time and stock status for MAX232IDWG4?
Current stock and lead time for MAX232IDWG4 should be confirmed through the Request a Quote form on this page. The exact suffix identifies the 16-pin SOIC configuration and tube packaging, which is important when matching a replacement. A quotation response can confirm availability, manufacturing status, and the current lead time for the quantity required by the project.

Datos de referencia de ingeniería para MAX232IDWG4 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose MAX232IDWG4 for a conventional 5 V RS-232 interface that needs two transmitters, two receivers, operation up to 120 kbit/s, and approximately ±9 V cable-side output. Its integrated charge pump and 1.0 uF external capacitors simplify designs based on classic bipolar RS-232. Consider MAX232EESE+T when the same footprint and channel count can be retained but stronger ±15 kV HBM ESD protection is valuable. HIN232CBZ-T is a cross-brand candidate that requires careful review of pin functions, data rate, ESD rating, supply current, and operating limits before production release. Do not select MAX232IDWG4 for 3.3 V-only logic without a translator, and confirm the device's exact suffix, tube packaging, operating-temperature grade, and lifecycle status before releasing a production order.

Comparación con alternativas

Parámetro Este producto MAX232EESE+T HIN232CBZ-T
Brand Texas Instruments Texas Instruments Intersil
Package 16-SOIC 16-SOIC 16-SOIC
Product Type Dual RS-232 driver and receiver Dual RS-232 driver and receiver RS-232 driver and receiver
Supply Voltage 5 V 5 V 5 V
Number of Drivers 2 2 2
Number of Receivers 2 2 2

Diferenciadores clave

  • Higher documented ESD protection in the same SOIC footprint (frente a MAX232EESE+T)
  • Documented receiver input tolerance and hysteresis (frente a HIN232CBZ-T)
  • Clear high-speed RS-232 capability (frente a HIN232CBZ-T)

Notas de diseño

Place the two 1.0 uF charge-pump capacitors close to the corresponding MAX232 pins and keep their return-current paths short. Follow the capacitor configuration shown in the manufacturer datasheet, including polarity and connection to the charge-pump nodes. Place the device near the RS-232 connector so driver outputs do not run long parallel paths beneath sensitive analog or high-speed digital traces. Maintain the board outline and land pattern for the 16-pin SOIC package.

Treat both RS-232 transmitter outputs as interference-prone bipolar signals even though they use single-ended logic at the IC pins. Route TX and TXD nets away from clocks, sensor inputs, ADC signals, and external crystal circuits. Do not assume that a logic-level ground near the connector eliminates cable-borne transients. Validate the complete interface with the intended cable, connector, baud rate, and grounding arrangement because RS-232 can behave differently under unbalanced or long-cable conditions.

Confirm that every connected UART uses compatible 5 V logic levels; MAX232IDWG4 does not make 3.3 V GPIO signals safe for direct connection. Also avoid confusing the RS-232 data pins with RS-485 A/B lines, and verify TX-to-RX crossover at the connector. Before selecting a substitute, compare every pin name, charge-pump connection, external capacitor, supply limit, receiver threshold, and operating-temperature condition in the manufacturer datasheets.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The available product information identifies the device as a Texas Instruments 5 V RS-232 interface IC but does not explicitly state the requested compliance statuses. JESD-2000 is referenced in the device description as the ESD comparison context.

Datos verificados el: 2026-11-09 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

MAX232IDWG4 datasheet MAX232IDWG4 pinout MAX232IDWG4 datasheet pdf Texas Instruments MAX232IDWG4 MAX232IDWG4 120kbps specifications MAX232IDWG4 16-SOIC pinout MAX232IDWG4 RS-232 application circuit MAX232IDWG4 vs MAX232EESE+T MAX232IDWG4 drop-in replacement MAX232IDWG4 cross reference MAX232IDWG4 price MAX232IDWG4 stock

Componentes & términos relacionados

Texas Instruments MAX232IDWG4 MAX232EESE+T HIN232CBZ-T RS-232 RS-232 transceiver line driver line receiver interface IC EIA-232 TIA-232 V.28 UART charge-pump capacitor single 5 V supply 120 kbit/s receiver hysteresis ESD protection 16-pin SOIC SOIC family surface mount industrial control interface test equipment legacy serial port
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ