MAX311EPE - 8-Channel RF Video Multiplexer | Maxim Integrated
MPN: MAX311EPE ✓ ActiveMAX311EPE Overview
An RF/video multiplexer is a signal-routing semiconductor that selects among multiple analog inputs and connects the selected channel to an output. In the broader hierarchy, it belongs to the switch and multiplexer family, the interface IC category, and ultimately the semiconductor and signal-path component classes. This distinction from a digital multiplexer is important: the MAX311EPE carries analog or RF signals and therefore depends on off-state isolation, on-state resistance, bandwidth, and switching speed rather than digital logic levels.
Key features include eight multiplexed channels, CMOS construction, a maximum on-resistance of 250 ohms, and maximum on and off times of 1 microsecond. The high-frequency isolation characteristic helps prevent an unselected input from coupling energy into the selected output. With positive and negative 15 V supplies, the supported input signal range extends from +12 V to -15 V, allowing bipolar analog signals to be routed while the device remains in the analog signal path.
Technically, the MAX311EPE uses complementary CMOS switching structures to control the analog channels. When one address is asserted, the corresponding input is connected to the output; the address decoder and enable logic determine which channel conducts. The -66 dB off-isolation guarantee at 5 MHz is especially relevant when adjacent sources carry high-frequency video or RF content, because it limits crosstalk between the active and inactive inputs. The 250-ohm maximum on resistance must also be included in gain-loss and impedance calculations for downstream receivers.
Typical applications include video test equipment, RF signal-routing systems, instrumentation, broadcast and professional video interfaces, and analog measurement setups where several signal sources must share a receiver or analyzer. The MAX311EPE is most appropriate where bipolar signal handling and channel isolation matter more than very low on resistance. Systems operating at substantially higher frequencies or requiring lower insertion loss should verify bandwidth and impedance behavior against the complete circuit rather than relying only on the isolation rating.
A key design consideration is the interaction between switching transients, grounding, and downstream input capacitance. Keep the selected signal path short, maintain a low-impedance return connection, and use the manufacturer pin-description table when assigning address and control traces. Verify the positive and negative supply sequencing requirements, bypass each supply rail close to the device, and account for the 1-microsecond maximum transition time when the muxed receiver cannot tolerate channel-switch transients.
This page combines the available manufacturer-level electrical characteristics, packaging information, sourcing guidance, and application engineering notes into a design-oriented overview. It also highlights where a replacement must be checked against the original 16-pin DIP footprint, pin functions, supply arrangement, signal range, isolation, on-resistance, and switching timing rather than being selected from channel count alone.
Drop-in alternatives for MAX311EPE — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
MAX311CPE
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
MAX311EWE
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
5962-9455602MEA
✅ Drop-In📋 Reference alternative (not in catalog)
MAX311EPE Specifications
| Number of Channels | 8 channels |
| Device Type | CMOS RF/video multiplexer |
| Signal Configuration | 8-channel RF/video analog multiplexer |
| On Resistance | 250 ohms maximum |
| On Time | 1 us maximum |
| Off Time | 1 us maximum |
| Off-Channel Isolation | -66 dB at 5 MHz |
| Input Signal Range | +12 V to -15 V with plus or minus 15 V power supplies |
| Typical Power Consumption | 1.1 mW |
| Supply Voltage | Plus or minus 15 V |
| Package | 16-pin DIP |
| Technology | CMOS |
MAX311EPE 16-pin dip Pin Configuration Guide
Pin configuration for MAX311EPE (16-pin dip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MAX311EPE.
Refer to the datasheet for full pin configuration.
Typical Applications
MAX311EPE is suitable for 6 applications: RF Channel Selection, Professional Video Signal Routing, Automated Test Instrumentation, Analog Signal Patch Panels, Broadcast Equipment Signal Selection, Industrial Interface Multiplexing.
RF Channel Selection
The MAX311EPE is appropriate for routing one of several RF sources into a shared receiver or measurement chain. Its eight-channel architecture simplifies selection without requiring eight separate RF switches, while the guaranteed -66 dB off isolation at 5 MHz limits coupling from inactive sources. The 250-ohm maximum on resistance should be included in the insertion-loss calculation. Designers should also allow for the 1-microsecond maximum switching interval and verify that downstream circuitry settles before a measurement is captured.
Recommended
Professional Video Signal Routing
The MAX311EPE can select among eight video or composite-style analog sources when the system operates within its documented bipolar signal range. The -66 dB off-isolation rating at 5 MHz helps reduce crosstalk when neighboring channels contain energetic video content. Designers should calculate the voltage division introduced by the 250-ohm maximum on resistance and the source impedance, then confirm settling within the 1-microsecond maximum on and off times. Proper grounding and short signal routes remain essential for stable video performance.
Recommended
Automated Test Instrumentation
The MAX311EPE is suitable for test systems that route multiple sources into a common measuring instrument. Eight channels reduce the number of discrete switching elements, and the 1-microsecond maximum transition times support reasonably fast source selection. The device's 250-ohm maximum on resistance must be included in the instrument input-loading analysis, while -66 dB off isolation at 5 MHz helps limit interaction between active and inactive sources. For precision measurements, validate source impedance, termination, settling time, and channel-to-channel crosstalk in the complete fixture.
Recommended
Analog Signal Patch Panels
The MAX311EPE can serve as the active element in an analog patch panel that routes eight inputs to one measurement or processing channel. Its CMOS implementation and 250-ohm maximum on resistance suit moderate-level bipolar signals, while the -66 dB off-isolation characteristic helps maintain channel separation at 5 MHz. The circuit must include suitable source and load impedances, and the routing should minimize loop area. Engineers should also prevent control-code transitions from causing invalid transients during source changes.
Recommended
Broadcast Equipment Signal Selection
Broadcast and professional media equipment can use the MAX311EPE to select among eight analog video or related baseband sources. The eight-channel architecture provides compact routing, and the specified -66 dB off isolation at 5 MHz is valuable when adjacent channels carry high-frequency content. The 250-ohm maximum on resistance introduces source-dependent attenuation that must be included in gain planning. Because transitions can reach 1 microsecond, downstream synchronization and blanking requirements should be checked before using the device inside a live video path.
Recommended
Industrial Interface Multiplexing
The MAX311EPE can consolidate several bipolar analog signals in an industrial interface or diagnostic system. It is most useful where one receiver or controller must inspect multiple sources sequentially and the system can tolerate the maximum 250-ohm on resistance. The 1-microsecond on and off times support relatively quick selection, while -66 dB off isolation at 5 MHz improves separation between channels. Protection, grounding, supply bypassing, and source-voltage compliance must be evaluated independently of the multiplexer ratings to keep the industrial interface reliable.
Recommended
Recommended Products Summary
Engineering reference data for MAX311EPE — comparison, design guidance, and compliance information.
Selection Guide
Do not select a generic eight-channel switch based only on channel count. A valid alternative must preserve the 16-pin footprint, address and enable functions, power connections, logic levels, absolute maximum ratings, on resistance, switching times, isolation, and signal range. The MAX311MJE is a related family member, but its CDIP-16 construction requires a separate package, temperature-grade, and electrical review rather than an automatic drop-in substitution. Use the Request a Quote form to discuss current sourcing and an approved replacement path.
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Brand | Maxim Integrated |
| Package | 16-pin DIP |
| Number of Channels | 8 channels |
| Device Type | CMOS RF/video multiplexer |
| On Resistance | 250 ohms maximum |
| On Time | 1 us maximum |
| Off Time | 1 us maximum |
| Off-Channel Isolation | -66 dB at 5 MHz |
| Input Signal Range | +12 V to -15 V with plus or minus 15 V supplies |
| Typical Power Consumption | 1.1 mW |
Key Differentiators
- Guaranteed high-frequency off isolation (vs General-purpose eight-channel CMOS analog switch)
- Bipolar analog signal range (vs Single-supply low-voltage analog multiplexer)
- Defined channel-transition timing (vs General-purpose mechanical or relay switch)
Design Notes
Include the 250-ohm maximum on resistance in the source-to-receiver voltage-divider calculation. For a receiver with high input impedance, the loss is usually modest; for a 50-ohm source and lower-impedance load, attenuation may be more important. Check the selected channel for settling after the 1-microsecond maximum transition time, especially when the downstream circuit samples immediately following an address change.
Route the selected analog output as a short, direct path and keep the return connection continuous to minimize coupling from inactive channels. Place supply-bypass components close to the appropriate pins, separate the address and enable traces from the RF or video node, and maintain a stable ground reference. A compact layout helps preserve the -66 dB off-isolation benefit at 5 MHz and reduces sensitivity to board-level interference.
Do not treat the MAX311EPE as a modern low-resistance RF switch without recalculating insertion loss. Its input signal range of +12 V to -15 V is tied to plus or minus 15 V operation, so source transients must remain within the absolute maximum limits. Also avoid changing channels while the downstream receiver is interpreting the output unless the system provides blanking or sufficient settling time for the 1-microsecond maximum switching interval.
Compliance Information
The technical document lists the device as a Maxim Integrated CMOS RF/video multiplexer; no explicit RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive qualification statement is identified.