Analog Devices

MAX3232EEAE+G1Z - Dual RS-232 Transceiver | Analog Devices

MPN: MAX3232EEAE+G1Z ✓ Active
3.0 V to 5.5 V Vdss 16-pin SSOP Package
MOQ: 1 |

MAX3232EEAE+G1Z Overview

The Analog Devices MAX3232EEAE+G1Z is a 2-driver/2-receiver full RS-232 transceiver designed for serial-interface systems operating from 3.0 V to 5.5 V. It supports data rates up to 1 Mbps, provides ±15 kV ESD protection, and is offered in a 16-pin SSOP package. The G1Z ordering designation identifies the qualified configuration associated with this MAX3232E-family device.

An RS-232 transceiver is an interface IC that translates between logic-level signals used by digital circuits and the voltage levels defined for RS-232 serial links. A full transceiver combines transmit and receive functions in one package. The MAX3232EEAE+G1Z provides two transmit channels and two receive channels, allowing a board to exchange data in both directions while limiting the number of external interface components and conserving board area.

The device operates from a 3.0 V minimum supply to a 5.5 V maximum supply, accommodating common 3.3 V and 5 V system rails. Its maximum supported data rate of 1 Mbps makes it suitable for instrument control, configuration interfaces, point-of-sale equipment, and other systems that transfer moderate amounts of serial data. The stated ±15 kV ESD protection helps strengthen the interface against electrostatic discharge encountered during handling and connection.

As a true RS-232 transceiver, the MAX3232EEAE+G1Z is intended for point-to-point serial communication rather than a multipoint bus. Each driver converts logic-level inputs into RS-232 output levels, while each receiver converts incoming RS-232 signals into logic-level outputs. This division of functions allows two device-to-device channels to operate in opposite directions within one compact interface circuit.

Typical uses include industrial control equipment, test and measurement instruments, transactional terminals, security-system accessories, and embedded service ports. Designers should pair the IC with the charge-pump and interface components specified by the manufacturer, observe the recommended pin connections, and validate signal integrity at the intended baud rate and cable length.

The principal design consideration is that RS-232 is a single-ended, point-to-point interface whose voltage levels differ from modern CMOS logic. Correct driver population, supply decoupling, grounding, connector exposure, and cable routing are therefore more important than treating the transceiver as an ordinary UART peripheral. Confirm every board-level connection against the MAX3232E datasheet before production release.

This product page combines the manufacturer's device positioning with package, interface, sourcing, and replacement information designed for faster engineering evaluation. It also distinguishes electrically interchangeable ordering variants from design changes that would require a different package or a redesigned RS-232 interface.

Drop-in alternatives for MAX3232EEAE+G1Z — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MAX3232EEAE+G1Z (same form factor and footprint) — differing in Interface Standard, Product Type.

Analog Devices
Interface Standard: TIA/EIA-232-F
Product Type: True RS-232 transceiver
Compare with MAX3232EEAE+G1Z →

MAX3232EEAE+

✅ Drop-In
Analog Devices
📦 16-SSOP
True RS-232 transceiver · 2 · 2 · 3.0 V to 5.5 V · 1 Mbps · ±15 kV · Down to 10 nA · 2

Contact for price

View Datasheet →

MAX3232EEAE

✅ Drop-In
📦 16-SSOP
The +G1Z suffix is absent, while the 3.0 V to 5.5 V supply, 1 Mbps data rate, and ±15 kV ESD rating remain unchanged (0% change in these headline ratings)

📋 Reference alternative (not in catalog)

MAX3232EEAE+G1Z Specifications

Product Type Full RS-232 transceiver
Transmitter Count 2 drivers
Receiver Count 2 receivers
Supply Voltage Range 3.0 V to 5.5 V
Maximum Data Rate 1 Mbps
ESD Protection ±15 kV
Low-Power Feature 10 nA
Interface Standard True RS-232
Package 16-pin SSOP
Mounting Type Surface mount
Automotive Ordering Designation G1Z

MAX3232EEAE+G1Z Pin Configuration

SSOP-16 Package Pinout Diagram SSOP-16 3.9x6.0mm, P0.635mm, JEDEC MO-150. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SSOP-16
Pin 1 C1+ — Charge-pump capacitor positive terminal
Pin 2 V+ — Charge-pump output
Pin 3 C1- — Charge-pump capacitor negative terminal
Pin 4 C2+ — Charge-pump capacitor positive terminal
Pin 5 C2- — Charge-pump capacitor negative terminal
Pin 6 V- — Negative charge-pump output
Pin 7 T1OUT — First RS-232 driver output
Pin 8 R1IN — First RS-232 receiver input
Pin 9 R2IN — Second RS-232 receiver input
Pin 10 R2OUT — Second receiver logic output
Pin 11 T2IN — Second driver logic input
Pin 12 T2OUT — Second RS-232 driver output
Pin 13 VCC — Positive supply input
Pin 14 GND — Ground connection
Pin 15 T1IN — First driver logic input
Pin 16 R1OUT — First receiver logic output

Typical Applications

MAX3232EEAE+G1Z is suitable for 6 applications: Industrial Control Terminals, Test and Measurement Instruments, Point-of-Sale Equipment, Embedded Service and Configuration Ports, Security and Access-Control Peripherals, Data Acquisition and Control Modules.

🏭

Industrial Control Terminals

The MAX3232EEAE+G1Z fits industrial equipment that exposes a point-to-point RS-232 configuration or service port. Its two-driver/two-receiver arrangement supports bidirectional control traffic, while the 3.0 V to 5.5 V supply range accommodates common 3.3 V and 5 V embedded rails. The stated 1 Mbps capability exceeds many legacy serial-control rates, and ±15 kV ESD protection improves robustness around exposed equipment interfaces. For deployment, connect the logic-side UART to the receiver and driver pins according to the datasheet, place the specified charge-pump and bypass capacitors close to their terminals, and verify grounding and cable behavior in the final enclosure.

🔧

Test and Measurement Instruments

The MAX3232EEAE+G1Z is appropriate for instruments that exchange commands and measurement data over RS-232. Two transmit channels and two receive channels allow one instrument to receive commands and transmit results without requiring separate interface packages. Operation from 3.0 V to 5.5 V supports both 3.3 V and 5 V instrument architectures, and the 1 Mbps limit provides ample margin for many measurement-control protocols. The ±15 kV ESD rating is particularly relevant when users connect cables or accessories to a benchtop or field instrument. Designers should preserve the recommended charge-pump network, use a low-impedance ground strategy, and validate the UART baud rate, cable length, and connector behavior as one channel.

🖥️

Point-of-Sale Equipment

The MAX3232EEAE+G1Z can interface a point-of-sale terminal or peripheral with a legacy serial host. The full 2/2 transceiver architecture supports simultaneous command reception and data transmission, while operation down to 3.0 V allows integration with modern embedded controllers. Its maximum 1 Mbps data rate exceeds the requirements of many peripheral protocols, and the 16-pin SSOP package limits board-space consumption. In a retail installation, protect the connector path and maintain a consistent ground between connected equipment because RS-232 is single-ended. Follow the manufacturer circuit for charge-pump capacitors, connect only the required driver outputs, and validate communication with the exact peripheral cable and power-supply arrangement.

🧩

Embedded Service and Configuration Ports

The MAX3232EEAE+G1Z is suitable for embedded equipment that retains a service connector for firmware loading, configuration, or diagnostic communication. Two receivers can accept status or handshake signals from more than one compatible source, while two drivers provide outbound control or response channels. The 3.0 V minimum supply supports systems that cannot use a 5 V-only interface, and the 1 Mbps capability allows modern maintenance tools to use higher baud rates. The ±15 kV ESD protection rating helps manage static-discharge exposure associated with repeated service connections. Keep service connectors physically separated from sensitive analog sections and follow the datasheet's power, grounding, and external-capacitor guidance for reliable field behavior.

📹

Security and Access-Control Peripherals

The MAX3232EEAE+G1Z can serve as the RS-232 interface in access-control readers, camera-control equipment, and other security peripherals that communicate with a controller. Its two transmit and two receive channels support command, response, and handshake signals, while the 3.0 V to 5.5 V range permits use alongside common embedded processors. Data rates up to 1 Mbps cover substantially more bandwidth than many legacy security-control links. The ±15 kV ESD protection rating adds useful protection when a peripheral connector is accessible during installation or maintenance. A robust installation still requires chassis grounding, short suitable cable runs, and verification of logic levels because the external RS-232 signals are not direct CMOS pins.

📊

Data Acquisition and Control Modules

The MAX3232EEAE+G1Z fits compact data-acquisition and industrial-control modules that communicate with a host computer through RS-232. The 16-pin SSOP package reduces board area, and the two transmit/two receive arrangement can carry commands, measurements, and status information over the interface. Its 3.0 V to 5.5 V operating range supports low-voltage system rails, while the 1 Mbps data-rate capability permits efficient transfer of moderate command and measurement traffic. ±15 kV ESD protection improves the interface's tolerance of electrostatic discharge. In a measurement module, isolate analog and digital grounding appropriately, route the RS-232 traces away from sensitive inputs, and implement the manufacturer's external capacitor network exactly as specified.

Recommended Products Summary

MAX3232EEAE+ Analog Devices Used in: Industrial Control Terminals, Test and Measurement Instruments, Point-of-Sale Equipment, Embedded Service and Configuration Ports, Security and Access-Control Peripherals, Data Acquisition and Control Modules MAX3232EEAE Same-family RS-232 transceiver without the extended ordering suffix Used in: Industrial Control Terminals, Test and Measurement Instruments, Point-of-Sale Equipment, Embedded Service and Configuration Ports, Security and Access-Control Peripherals, Data Acquisition and Control Modules
What is the MAX3232EEAE+G1Z?
The MAX3232EEAE+G1Z is a 2-driver/2-receiver full RS-232 transceiver from Analog Devices. According to the manufacturer product page, it supports a 3.0 V to 5.5 V supply, data rates up to 1 Mbps, and ±15 kV ESD protection. It is packaged in a 16-pin SSOP and is intended for bidirectional point-to-point serial communication between equipment and control or peripheral systems.
What are the key specifications of MAX3232EEAE+G1Z that engineers should know?
The key specifications are two RS-232 drivers, two RS-232 receivers, a 3.0 V to 5.5 V operating supply, and throughput up to 1 Mbps. The manufacturer also identifies ±15 kV ESD protection and a 16-pin SSOP package. These parameters place the device in the full-duplex, multipin RS-232 transceiver class and make it suitable for embedded serial ports that require both transmitting and receiving functions.
Where can I download the MAX3232EEAE+G1Z datasheet PDF?
The official MAX3232E documentation is available from the Analog Devices product page at https://www.analog.com/en/products/max3232e.html. Select the datasheet or PDF document associated with the MAX3232E family. Use the manufacturer document for the exact G1Z ordering code, external charge-pump connections, pin assignments, operating limits, and recommended interface components.
Where is the MAX3232EEAE+G1Z pinout?
The MAX3232EEAE+G1Z pinout is found in the pin-description and typical-application diagrams in the Analog Devices MAX3232E datasheet. The device uses a 16-pin SSOP package. When assigning PCB tracks, use the pin-description table rather than relying only on the functional block diagram, and confirm the package drawing dimensions and terminal numbering against the selected ordering code.
Can the MAX3232EEAE+G1Z operate from a 3.3 V system?
Yes. The MAX3232EEAE+G1Z supports a 3.0 V to 5.5 V operating supply, so a regulated 3.3 V rail is within its stated range. The transceiver still produces RS-232-level signals at its external driver outputs, which means the host logic voltage and the interface voltage are different domains. Confirm external capacitor values, bypass layout, and all logic thresholds in the manufacturer datasheet.
Is MAX3232EEAE+G1Z suitable for high-speed serial communication?
The MAX3232EEAE+G1Z supports data rates up to 1 Mbps, making it suitable for RS-232 links that exceed the speed of many legacy 115200-baud designs. Achievable system throughput also depends on the connected UART, cable characteristics, grounding, connector implementation, and signal-integrity margin. Validate the complete channel rather than selecting the data-rate limit in isolation.
What is the difference between MAX3232EEAE+G1Z and MAX3232EEAE+?
The MAX3232EEAE+G1Z and MAX3232EEAE+ share the 3.0 V to 5.5 V supply, 1 Mbps data-rate capability, ±15 kV ESD protection, and 16-pin SSOP format. Their ordering designations differ, with G1Z identifying the qualified configuration while the + suffix identifies the base ordering option. Review the manufacturer ordering table for qualification and procurement requirements before substitution.
What can replace MAX3232EEAE+G1Z?
The closest identified replacement is MAX3232EEAE+, which retains the same 16-pin SSOP package and the stated 3.0 V to 5.5 V, 1 Mbps, and ±15 kV electrical ratings. A production replacement should also be checked for qualification, availability, charge-pump capacitor requirements, and lifecycle status. Use the Request a Quote form on this page to confirm the exact ordering code and supply status.
Is MAX3232EEAE+G1Z the same as MAX3232EEAE+?
No. They are closely related MAX3232E-family orderings, but MAX3232EEAE+G1Z carries the G1Z designation and MAX3232EEAE+ carries the + designation. Both are 16-pin SSOP 2/2 RS-232 transceivers with the same headline voltage, speed, and ESD ratings. Their ordering and qualification requirements must be checked before treating them as identical.
When should I choose MAX3232EEAE+G1Z instead of MAX3232EEAE+?
Choose MAX3232EEAE+G1Z when the G1Z ordering and qualification requirements match the equipment being designed. Choose MAX3232EEAE+ when the base ordering option satisfies the product's qualification and procurement requirements. Both retain the same 16-pin SSOP format and headline electrical capabilities, so the deciding factors are qualification, availability, documentation, and lifecycle rather than basic RS-232 functionality.
Is MAX3232EEAE+G1Z suitable for industrial control equipment?
The MAX3232EEAE+G1Z can suit industrial control equipment that uses a point-to-point RS-232 service port. Its 3.0 V to 5.5 V supply range supports common embedded rails, while ±15 kV ESD protection adds interface robustness. The enclosure, cable length, grounding arrangement, connector type, and qualification requirements still determine suitability for a specific industrial installation.
Where can I buy MAX3232EEAE+G1Z online?
Use the Request a Quote form on this page to request the MAX3232EEAE+G1Z by its complete ordering code, including the G1Z suffix. The form is the appropriate route for current commercial availability, lot traceability, and quotation requests. Engineers should state the required package form, quantity, and production timeline when submitting the request.
What is the price of MAX3232EEAE+G1Z?
Current commercial pricing for MAX3232EEAE+G1Z should be obtained through the Request a Quote form on this page. Quote requests should identify the complete MAX3232EEAE+G1Z ordering code, required quantity, and target delivery schedule. This approach allows the exact configuration and any requested production traceability to be confirmed before an order is placed.
What is the lead time for MAX3232EEAE+G1Z?
The current lead time for MAX3232EEAE+G1Z should be requested through the Request a Quote form on this page. Include the required quantity, target ship date, and whether the shipment must be reeled or supplied in another approved packing form. This allows procurement planning to reflect the exact MPN and delivery requirement rather than a generic family lead time.
Is MAX3232EEAE+G1Z in stock?
Current inventory status for MAX3232EEAE+G1Z should be confirmed through the Request a Quote form on this page. State the desired quantity and target schedule so the response can reflect the correct ordering code and packing format. The form avoids ambiguity between the G1Z configuration and other MAX3232EEAE ordering variants.

Engineering reference data for MAX3232EEAE+G1Z — comparison, design guidance, and compliance information.

Selection Guide

Choose MAX3232EEAE+G1Z when the G1Z ordering designation, qualification requirements, and production sourcing plan match the target equipment. It is a 2/2 full-duplex RS-232 transceiver rated from 3.0 V to 5.5 V, up to 1 Mbps, and ±15 kV ESD protection in a 16-pin SSOP. MAX3232EEAE+ is the closest identified drop-in alternative when the base ordering satisfies the product requirements. MAX3232EEAE is also electrically and package compatible for these headline specifications, but its ordering and qualification status must be checked separately. The design should be driven by the completed requirements: qualification, exact charge-pump network, operating-temperature limits, lifecycle status, packing format, and delivered availability. If none of those distinctions apply, select the ordering code with the most suitable production qualification and supply plan rather than changing the interface footprint.

Comparison with Alternatives

Parameter This Product MAX3232EEAE+ MAX3232EEAE
Brand Analog Devices Analog Devices Analog Devices
Package 16-SSOP 16-SSOP - same 16-SSOP - same
Transmitter and Receiver Count 2/2 2/2 2/2
Supply Voltage Range 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V
Maximum Data Rate 1 Mbps 1 Mbps 1 Mbps
ESD Protection ±15 kV ±15 kV ±15 kV
Ordering Designation +G1Z + No suffix
Low-Power Feature 10 nA 10 nA 10 nA

Key Differentiators

  • Retains full 2/2 RS-232 functionality in the same 16-SSOP footprint (vs MAX3232EEAE+)
  • Provides the same high-speed interface capability as the base ordering (vs MAX3232EEAE)
  • Matches the base family's stated ESD protection (vs MAX3232EEAE+)
  • Supports the same 3.3 V and 5 V embedded system environments (vs MAX3232EEAE)

Design Notes

Place the charge-pump capacitors and supply bypass capacitor at the terminals specified by the MAX3232E datasheet, keeping each loop short and avoiding current paths beneath the device. This matters because long capacitor routes increase parasitic inductance and can degrade charge-pump behavior or introduce noise. Use the manufacturer-recommended capacitance and voltage rating, and place the decoupling capacitor close to VCC and GND.

Do not treat RS-232 driver outputs as ordinary logic outputs or apply them directly to a UART. Use the receiver side for incoming RS-232 signals and connect each UART transmit signal to the appropriate driver input. Also avoid using an RS-232 transceiver as if it were an RS-485 device: the interface is single-ended and intended for point-to-point links rather than a multidrop bus.

Route the RS-232 driver and receiver nets away from clocks, switching-node traces, and sensitive analog inputs. Maintain a consistent ground reference between connected equipment and evaluate connector-to-board cable geometry, because long or poorly grounded single-ended paths can reduce noise margin. ESD protection is useful at the connector, but it does not replace controlled grounding, short traces, and appropriate interface-layer layout.

Design the 3.0 V to 5.5 V supply rail so that it remains within the MAX3232EEAE+G1Z operating range under startup, load, and system transients. Confirm capacitor tolerances and leakage characteristics against the charge-pump requirements in the manufacturer datasheet. If the host operates from another voltage, use suitable level translation on the logic side while preserving the RS-232 interface arrangement.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The G1Z ordering designation is listed for MAX3232EEAE+G1Z, but the applicable qualification and compliance declarations require confirmation from the manufacturer ordering information.

Data verified on: 2026-11-09 — data verified and curated by XAIPART's component engineering team

Related Searches

MAX3232EEAE+G1Z datasheet MAX3232EEAE+G1Z datasheet pdf MAX3232EEAE+G1Z pinout MAX3232EEAE+G1Z specifications MAX3232EEAE+G1Z equivalent MAX3232EEAE+G1Z replacement MAX3232EEAE+G1Z vs MAX3232EEAE+ MAX3232EEAE+G1Z price MAX3232EEAE+G1Z stock Analog Devices MAX3232EEAE+G1Z MAX3232EEAE+G1Z 16-SSOP MAX3232EEAE+G1Z RS-232 application circuit

Related Components & Terms

Analog Devices MAX3232EEAE+G1Z MAX3232EEAE+ MAX3232EEAE MAX3232E RS-232 full-duplex transceiver line-driver receiver interface IC semiconductor 2/2 transceiver 3.0 V to 5.5 V 1 Mbps ±15 kV ESD protection 16-pin SSOP SSOP family surface-mount package charge-pump capacitor point-to-point serial communication industrial control test and measurement point-of-sale equipment service port data acquisition
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details