MAX3232EEAE+G1Z - Dual RS-232 Transceiver | Analog Devices
MPN: MAX3232EEAE+G1Z ✓ فعالMAX3232EEAE+G1Z نمای کلی
An RS-232 transceiver is an interface IC that translates between logic-level signals used by digital circuits and the voltage levels defined for RS-232 serial links. A full transceiver combines transmit and receive functions in one package. The MAX3232EEAE+G1Z provides two transmit channels and two receive channels, allowing a board to exchange data in both directions while limiting the number of external interface components and conserving board area.
The device operates from a 3.0 V minimum supply to a 5.5 V maximum supply, accommodating common 3.3 V and 5 V system rails. Its maximum supported data rate of 1 Mbps makes it suitable for instrument control, configuration interfaces, point-of-sale equipment, and other systems that transfer moderate amounts of serial data. The stated ±15 kV ESD protection helps strengthen the interface against electrostatic discharge encountered during handling and connection.
As a true RS-232 transceiver, the MAX3232EEAE+G1Z is intended for point-to-point serial communication rather than a multipoint bus. Each driver converts logic-level inputs into RS-232 output levels, while each receiver converts incoming RS-232 signals into logic-level outputs. This division of functions allows two device-to-device channels to operate in opposite directions within one compact interface circuit.
Typical uses include industrial control equipment, test and measurement instruments, transactional terminals, security-system accessories, and embedded service ports. Designers should pair the IC with the charge-pump and interface components specified by the manufacturer, observe the recommended pin connections, and validate signal integrity at the intended baud rate and cable length.
The principal design consideration is that RS-232 is a single-ended, point-to-point interface whose voltage levels differ from modern CMOS logic. Correct driver population, supply decoupling, grounding, connector exposure, and cable routing are therefore more important than treating the transceiver as an ordinary UART peripheral. Confirm every board-level connection against the MAX3232E datasheet before production release.
This product page combines the manufacturer's device positioning with package, interface, sourcing, and replacement information designed for faster engineering evaluation. It also distinguishes electrically interchangeable ordering variants from design changes that would require a different package or a redesigned RS-232 interface.
جایگزینهای drop-in برای MAX3232EEAE+G1Z — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MAX3232EEAE+G1Z (همان فرمفاکتور و فوتپرینت) — متفاوت در Interface Standard, Product Type.
MAX3232EEAE+
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MAX3232EEAE
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MAX3232EEAE+G1Z مشخصات
| Product Type | Full RS-232 transceiver |
| Transmitter Count | 2 drivers |
| Receiver Count | 2 receivers |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps |
| ESD Protection | ±15 kV |
| Low-Power Feature | 10 nA |
| Interface Standard | True RS-232 |
| بستهبندی | 16-pin SSOP |
| نوع نصب | Surface mount |
| Automotive Ordering Designation | G1Z |
پیکربندی پین MAX3232EEAE+G1Z
| پین 1 | C1+ — Charge-pump capacitor positive terminal |
| پین 2 | V+ — Charge-pump output |
| پین 3 | C1- — Charge-pump capacitor negative terminal |
| پین 4 | C2+ — Charge-pump capacitor positive terminal |
| پین 5 | C2- — Charge-pump capacitor negative terminal |
| پین 6 | V- — Negative charge-pump output |
| پین 7 | T1OUT — First RS-232 driver output |
| پین 8 | R1IN — First RS-232 receiver input |
| پین 9 | R2IN — Second RS-232 receiver input |
| پین 10 | R2OUT — Second receiver logic output |
| پین 11 | T2IN — Second driver logic input |
| پین 12 | T2OUT — Second RS-232 driver output |
| پین 13 | VCC — Positive supply input |
| پین 14 | GND — Ground connection |
| پین 15 | T1IN — First driver logic input |
| پین 16 | R1OUT — First receiver logic output |
کاربردهای معمول
MAX3232EEAE+G1Z مناسب است برای 6 کاربردs: Industrial Control Terminals, Test and Measurement Instruments, Point-of-Sale Equipment, Embedded Service and Configuration Ports, Security and Access-Control Peripherals, Data Acquisition and Control Modules.
Industrial Control Terminals
The MAX3232EEAE+G1Z fits industrial equipment that exposes a point-to-point RS-232 configuration or service port. Its two-driver/two-receiver arrangement supports bidirectional control traffic, while the 3.0 V to 5.5 V supply range accommodates common 3.3 V and 5 V embedded rails. The stated 1 Mbps capability exceeds many legacy serial-control rates, and ±15 kV ESD protection improves robustness around exposed equipment interfaces. For deployment, connect the logic-side UART to the receiver and driver pins according to the datasheet, place the specified charge-pump and bypass capacitors close to their terminals, and verify grounding and cable behavior in the final enclosure.
پیشنهادی
Test and Measurement Instruments
The MAX3232EEAE+G1Z is appropriate for instruments that exchange commands and measurement data over RS-232. Two transmit channels and two receive channels allow one instrument to receive commands and transmit results without requiring separate interface packages. Operation from 3.0 V to 5.5 V supports both 3.3 V and 5 V instrument architectures, and the 1 Mbps limit provides ample margin for many measurement-control protocols. The ±15 kV ESD rating is particularly relevant when users connect cables or accessories to a benchtop or field instrument. Designers should preserve the recommended charge-pump network, use a low-impedance ground strategy, and validate the UART baud rate, cable length, and connector behavior as one channel.
پیشنهادی
Point-of-Sale Equipment
The MAX3232EEAE+G1Z can interface a point-of-sale terminal or peripheral with a legacy serial host. The full 2/2 transceiver architecture supports simultaneous command reception and data transmission, while operation down to 3.0 V allows integration with modern embedded controllers. Its maximum 1 Mbps data rate exceeds the requirements of many peripheral protocols, and the 16-pin SSOP package limits board-space consumption. In a retail installation, protect the connector path and maintain a consistent ground between connected equipment because RS-232 is single-ended. Follow the manufacturer circuit for charge-pump capacitors, connect only the required driver outputs, and validate communication with the exact peripheral cable and power-supply arrangement.
پیشنهادی
Embedded Service and Configuration Ports
The MAX3232EEAE+G1Z is suitable for embedded equipment that retains a service connector for firmware loading, configuration, or diagnostic communication. Two receivers can accept status or handshake signals from more than one compatible source, while two drivers provide outbound control or response channels. The 3.0 V minimum supply supports systems that cannot use a 5 V-only interface, and the 1 Mbps capability allows modern maintenance tools to use higher baud rates. The ±15 kV ESD protection rating helps manage static-discharge exposure associated with repeated service connections. Keep service connectors physically separated from sensitive analog sections and follow the datasheet's power, grounding, and external-capacitor guidance for reliable field behavior.
پیشنهادی
Security and Access-Control Peripherals
The MAX3232EEAE+G1Z can serve as the RS-232 interface in access-control readers, camera-control equipment, and other security peripherals that communicate with a controller. Its two transmit and two receive channels support command, response, and handshake signals, while the 3.0 V to 5.5 V range permits use alongside common embedded processors. Data rates up to 1 Mbps cover substantially more bandwidth than many legacy security-control links. The ±15 kV ESD protection rating adds useful protection when a peripheral connector is accessible during installation or maintenance. A robust installation still requires chassis grounding, short suitable cable runs, and verification of logic levels because the external RS-232 signals are not direct CMOS pins.
پیشنهادی
Data Acquisition and Control Modules
The MAX3232EEAE+G1Z fits compact data-acquisition and industrial-control modules that communicate with a host computer through RS-232. The 16-pin SSOP package reduces board area, and the two transmit/two receive arrangement can carry commands, measurements, and status information over the interface. Its 3.0 V to 5.5 V operating range supports low-voltage system rails, while the 1 Mbps data-rate capability permits efficient transfer of moderate command and measurement traffic. ±15 kV ESD protection improves the interface's tolerance of electrostatic discharge. In a measurement module, isolate analog and digital grounding appropriately, route the RS-232 traces away from sensitive inputs, and implement the manufacturer's external capacitor network exactly as specified.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MAX3232EEAE+G1Z — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MAX3232EEAE+ | MAX3232EEAE |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SSOP | 16-SSOP - same | 16-SSOP - same |
| Transmitter and Receiver Count | 2/2 | 2/2 | 2/2 |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps | 1 Mbps | 1 Mbps |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV |
| Ordering Designation | +G1Z | + | No suffix |
| Low-Power Feature | 10 nA | 10 nA | 10 nA |
تفاوتهای کلیدی
- Retains full 2/2 RS-232 functionality in the same 16-SSOP footprint (در مقابلMAX3232EEAE+)
- Provides the same high-speed interface capability as the base ordering (در مقابلMAX3232EEAE)
- Matches the base family's stated ESD protection (در مقابلMAX3232EEAE+)
- Supports the same 3.3 V and 5 V embedded system environments (در مقابلMAX3232EEAE)
یادداشتهای طراحی
Place the charge-pump capacitors and supply bypass capacitor at the terminals specified by the MAX3232E datasheet, keeping each loop short and avoiding current paths beneath the device. This matters because long capacitor routes increase parasitic inductance and can degrade charge-pump behavior or introduce noise. Use the manufacturer-recommended capacitance and voltage rating, and place the decoupling capacitor close to VCC and GND.
Do not treat RS-232 driver outputs as ordinary logic outputs or apply them directly to a UART. Use the receiver side for incoming RS-232 signals and connect each UART transmit signal to the appropriate driver input. Also avoid using an RS-232 transceiver as if it were an RS-485 device: the interface is single-ended and intended for point-to-point links rather than a multidrop bus.
Route the RS-232 driver and receiver nets away from clocks, switching-node traces, and sensitive analog inputs. Maintain a consistent ground reference between connected equipment and evaluate connector-to-board cable geometry, because long or poorly grounded single-ended paths can reduce noise margin. ESD protection is useful at the connector, but it does not replace controlled grounding, short traces, and appropriate interface-layer layout.
Design the 3.0 V to 5.5 V supply rail so that it remains within the MAX3232EEAE+G1Z operating range under startup, load, and system transients. Confirm capacitor tolerances and leakage characteristics against the charge-pump requirements in the manufacturer datasheet. If the host operates from another voltage, use suitable level translation on the logic side while preserving the RS-232 interface arrangement.
اطلاعات انطباق
The G1Z ordering designation is listed for MAX3232EEAE+G1Z, but the applicable qualification and compliance declarations require confirmation from the manufacturer ordering information.