MAX326CPE+ - Quad SPST Low-Leakage Switch | Analog Devices
MPN: MAX326CPE+ ✓ ActiveMAX326CPE+ Overview
An analog switch is an integrated semiconductor device that connects or disconnects circuit nodes under digital control. The MAX326 belongs to the CMOS analog-switch hierarchy, where each of its four SPST channels provides a normally closed connection that opens when the corresponding control input is asserted. Unlike a mechanical relay, the device changes state electronically and without mechanical wear, making it suitable for precision measurement, signal-routing, and low-leakage test systems.
The MAX326CPE+ combines four switch channels in one package and specifies a typical charge injection of 2 pC. The 3.5 kΩ on resistance provides a defined signal-path impedance for moderate-load analog routing. The 10 pA maximum leakage specification limits unintended current transfer across an open switch, while the CMOS and TTL-compatible control interface allows the device to be driven by conventional digital logic. Its operating range from 10 V to 30 V accommodates both single-supply and higher-voltage dual-supply systems.
Each SPST channel provides one signal terminal and one common signal terminal, with four independent control inputs. The 16-pin PDIP package exposes the control and analog terminals for straightforward prototyping and through-hole PCB assembly. Because this package is not surface mount, the device is particularly convenient for laboratory instruments, educational platforms, legacy control systems, and prototypes where sockets or plated through-holes are preferred.
Typical uses include high-impedance sensor isolation, precision measurement front ends, low-level analog signal routing, automated test equipment, and data-acquisition systems. Its low leakage can preserve small currents and voltages that would be affected by a higher-leakage switch. The principal design consideration is on resistance: although 3.5 kΩ is suitable for many instrumentation signals, applications requiring low source impedance should verify that the resistance and associated signal degradation remain acceptable.
For reliable operation, keep every signal and control voltage within the manufacturer's specified absolute maximum ratings, account for switch charge injection during control transitions, and provide adequate logic levels for the selected supply configuration. Review the MAX326 manufacturer datasheet for the complete pin assignment, truth table, switching characteristics, and operating limits before constructing the PCB or choosing external drive circuitry.
This product summary combines the manufacturer product-page specifications with practical guidance on leakage, charge injection, supply configuration, package selection, and PCB implementation. It also identifies replacement constraints, allowing engineers to distinguish a true pin-compatible substitute from a merely similar quad-SPST device before committing a new design to production.
Drop-in alternatives for MAX326CPE+ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
MAX326CPE
✅ Drop-In📋 Reference alternative (not in catalog)
MAX326CPE+ Maximum Ratings & Electrical Characteristics
| Number of Switches | 4 circuits |
| Switch Configuration | 1:1 SPST |
| Number of Channels | 4 channels |
| On Resistance | 3.5 kΩ |
| Maximum Leakage Current | 10 pA |
| Typical Leakage Current | <1 pA |
| Typical Charge Injection | 2 pC |
| Single-Supply Operating Voltage | 10 V to 30 V |
| Dual-Supply Operating Voltage | ±5 V to ±18 V |
| Logic Compatibility | CMOS and TTL compatible |
| Technology | CMOS |
| Package | 16-pin PDIP |
| Mounting Type | Through-hole |
| Temperature Grade | Commercial |
| Number of Terminals | 16 |
| Package Shape | Rectangular |
MAX326CPE+ rectangular Pin Configuration Guide
Pin configuration for MAX326CPE+ (rectangular package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MAX326CPE+.
Refer to the datasheet for full pin configuration.
Typical Applications
MAX326CPE+ is suitable for 6 applications: High-Impedance Sensor Routing, Precision Measurement Front Ends, Automated Test Equipment, Data Acquisition Systems, Laboratory Instrumentation, Industrial Control Signal Isolation.
High-Impedance Sensor Routing
The MAX326CPE+ fits high-impedance sensor routing because its four SPST channels limit off-state current to 10 pA maximum and below 1 pA typical. It can connect or isolate sensors, amplifiers, and measurement inputs while preserving weak currents that could be affected by higher leakage. The 3.5 kΩ on resistance must be included in the sensor-source impedance calculation, and the 2 pC typical charge injection should be checked against the measurement settling window. The commercial 16-pin PDIP package also simplifies prototype wiring and through-hole instrument construction.
Recommended
Precision Measurement Front Ends
The MAX326CPE+ is suitable for precision measurement front ends where small leakage currents can disturb the reference node or sensor return path. Its four independently controlled SPST channels can isolate inputs during calibration, connect a known signal, and restore the measurement path without mechanical relay switching. The below-1 pA typical leakage reduces leakage-induced error, although the 3.5 kΩ on resistance can influence source impedance. Designers should also account for 2 pC typical charge injection and allow adequate settling before taking a reading.
Recommended
Automated Test Equipment
The MAX326CPE+ can serve as a low-leakage routing element in automated test equipment that connects DUT pins, test sources, and measurement channels. Four SPST paths provide useful channel density in a 16-pin PDIP package, while 10 pA maximum leakage helps preserve bias currents and high-impedance node voltages. The CMOS and TTL-compatible control interface supports conventional test-controller logic. For multiplexed fixtures, verify that 3.5 kΩ on resistance meets the allowable signal attenuation and that the 2 pC charge-injection transient remains acceptable to the selected measurement amplifier.
Recommended
Data Acquisition Systems
The MAX326CPE+ fits data-acquisition signal conditioning when a system must select or disconnect several low-level analog channels. Its four SPST switches allow a controller to route individual inputs while the below-1 pA typical leakage minimizes loading of high-impedance sensor networks. The device supports 10 V to 30 V single-supply or ±5 V to ±18 V dual-supply operation, enabling integration around laboratory and industrial acquisition equipment. Confirm the 3.5 kΩ channel resistance, account for 2 pC charge injection during selection transients, and follow the manufacturer truth table for control sequencing.
Recommended
Laboratory Instrumentation
The MAX326CPE+ is appropriate for laboratory instrumentation that routes calibration signals to sensitive analog nodes. Ultra-low leakage helps prevent an open switch from creating a measurement error, while four channels in one package provide a compact through-hole implementation. The 10 V to 30 V single-supply and ±5 V to ±18 V dual-supply ranges support multiple bench-instrument signal levels. Because the on resistance is 3.5 kΩ, use it for high-impedance sensing paths rather than low-impedance driver outputs, and include the 2 pC typical charge injection in settling calculations.
Recommended
Industrial Control Signal Isolation
The MAX326CPE+ can isolate low-current control and sensor paths in industrial systems where low off-state leakage is important. Its four SPST channels permit independent connection control, while CMOS and TTL-compatible inputs simplify interfacing with controller logic. The commercial-grade PDIP package supports repairable, through-hole control boards and avoids requiring a surface-mount rework process. Designers must verify that every analog signal remains within the supported single- or dual-supply range, consider the 3.5 kΩ channel resistance in the control-loop impedance budget, and observe all absolute-maximum ratings from the manufacturer datasheet.
Recommended
Recommended Products Summary
Engineering reference data for MAX326CPE+ — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MAX326CPE |
|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP |
| Brand | Analog Devices | Analog Devices |
| Number of Switches | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 SPST | 1:1 SPST |
| On Resistance | 3.5 kΩ | 3.5 kΩ |
| Mounting Type | Through-hole | Through-hole |
Key Differentiators
- Ultra-low leakage supports preservation of small high-impedance signals (vs MAX326CPE)
- Four independently controlled channels in one package (vs MAX326CPE)
- Broad single- and dual-supply operating ranges (vs MAX326CPE)
Design Notes
Treat the 3.5 kΩ on resistance as part of the source impedance presented to the switched node. It is generally appropriate for high-impedance sensing paths but may create excessive attenuation or phase shift when driving a low-impedance load. Simulate the complete source, switch, cable, and input-impedance network, and include the 2 pC typical charge injection when evaluating transient settling after a control transition.
Route the high-impedance analog terminals away from switching nodes, clock lines, and digital return currents. Keep the MAX326CPE+ control traces short enough to avoid false switching, use a solid ground reference, and place any required bypass capacitors close to the supply pins according to the manufacturer application guidance. Because the PDIP package exposes all terminals, inspect solder bridges and contamination on closely spaced analog and control pins after assembly.
Do not assume that every quad-SPST switch with a 16-pin PDIP outline is interchangeable. The switch type, normally closed or normally open behavior, on resistance, leakage, supply range, absolute maximum ratings, and truth table must all match. In particular, verify control polarity and the switched terminals in the MAX326 pin-description table before assigning PCB nets, because the available package summary does not expose the complete pin numbering.
Confirm whether the application uses the supported 10 V to 30 V single-supply range or the ±5 V to ±18 V dual-supply range. Keep all analog and logic voltages within their respective absolute maximum limits, especially during power-up, shutdown, and fault conditions. Provide a defined logic state before the analog node becomes active, because an uncontrolled control input could leave a sensitive measurement path connected or disconnected unexpectedly.
Compliance Information
The MAX326CPE+ is listed as a commercial-grade component, but the verified excerpts do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not indicated for this commercial-grade part.