Analog Devices

MAX326CPE+ - Quad SPST Low-Leakage Switch | Analog Devices

MPN: MAX326CPE+ ✓ Nakahanda
10 V to 30 V Vdss 10 pA Id 3.5 kΩ Rds(on) 16-pin PDIP Package
MOQ: 1 |

MAX326CPE+ Ulas

The Analog Devices MAX326CPE+ is a quad, single-pole single-throw CMOS analog switch with four independently controlled channels, an on-resistance of 3.5 kΩ, and a 16-pin PDIP package. The device supports supply voltages from 10 V to 30 V and dual supply operation from ±5 V to ±18 V. Its defining characteristic is ultra-low leakage, specified at 10 pA maximum and below 1 pA typical, making it suitable for high-impedance analog paths where switch leakage could disturb the signal.

An analog switch is an integrated semiconductor device that connects or disconnects circuit nodes under digital control. The MAX326 belongs to the CMOS analog-switch hierarchy, where each of its four SPST channels provides a normally closed connection that opens when the corresponding control input is asserted. Unlike a mechanical relay, the device changes state electronically and without mechanical wear, making it suitable for precision measurement, signal-routing, and low-leakage test systems.

The MAX326CPE+ combines four switch channels in one package and specifies a typical charge injection of 2 pC. The 3.5 kΩ on resistance provides a defined signal-path impedance for moderate-load analog routing. The 10 pA maximum leakage specification limits unintended current transfer across an open switch, while the CMOS and TTL-compatible control interface allows the device to be driven by conventional digital logic. Its operating range from 10 V to 30 V accommodates both single-supply and higher-voltage dual-supply systems.

Each SPST channel provides one signal terminal and one common signal terminal, with four independent control inputs. The 16-pin PDIP package exposes the control and analog terminals for straightforward prototyping and through-hole PCB assembly. Because this package is not surface mount, the device is particularly convenient for laboratory instruments, educational platforms, legacy control systems, and prototypes where sockets or plated through-holes are preferred.

Typical uses include high-impedance sensor isolation, precision measurement front ends, low-level analog signal routing, automated test equipment, and data-acquisition systems. Its low leakage can preserve small currents and voltages that would be affected by a higher-leakage switch. The principal design consideration is on resistance: although 3.5 kΩ is suitable for many instrumentation signals, applications requiring low source impedance should verify that the resistance and associated signal degradation remain acceptable.

For reliable operation, keep every signal and control voltage within the manufacturer's specified absolute maximum ratings, account for switch charge injection during control transitions, and provide adequate logic levels for the selected supply configuration. Review the MAX326 manufacturer datasheet for the complete pin assignment, truth table, switching characteristics, and operating limits before constructing the PCB or choosing external drive circuitry.

This product summary combines the manufacturer product-page specifications with practical guidance on leakage, charge injection, supply configuration, package selection, and PCB implementation. It also identifies replacement constraints, allowing engineers to distinguish a true pin-compatible substitute from a merely similar quad-SPST device before committing a new design to production.

Mga alternatibo na pwedeng ilagay na MAX326CPE+ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

MAX326CPE

✅ Drop-In
📦 16-pin PDIP
Same 4-channel SPST configuration, 3.5 kΩ on resistance, and 16-pin PDIP package; the ordering-code suffix differs by the trailing plus sign.

📋 Alternatibo na Reference (hindi sa katalogo)

MAX326CPE+ Mga Pinakamataas na Rating at Electrical Characteristics

Number of Switches 4 circuits
Switch Configuration 1:1 SPST
Number of Channels 4 channels
On Resistance 3.5 kΩ
Maximum Leakage Current 10 pA
Typical Leakage Current <1 pA
Typical Charge Injection 2 pC
Single-Supply Operating Voltage 10 V to 30 V
Dual-Supply Operating Voltage ±5 V to ±18 V
Logic Compatibility CMOS and TTL compatible
Technology CMOS
Packhaging 16-pin PDIP
Uri ng Pagpapasok Through-hole
Temperature Grade Commercial
Number of Terminals 16
Package Shape Rectangular

Gabay sa Pin Configuration ng MAX326CPE+ rectangular

Pin configuration para sa MAX326CPE+ (rectangular package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng rectangular package para sa MAX326CPE+

Wala ng detalyadong pinout data na magagamit para sa MAX326CPE+.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MAX326CPE+ ay nararapat para sa 6 aplikasyons: High-Impedance Sensor Routing, Precision Measurement Front Ends, Automated Test Equipment, Data Acquisition Systems, Laboratory Instrumentation, Industrial Control Signal Isolation.

🧩

High-Impedance Sensor Routing

The MAX326CPE+ fits high-impedance sensor routing because its four SPST channels limit off-state current to 10 pA maximum and below 1 pA typical. It can connect or isolate sensors, amplifiers, and measurement inputs while preserving weak currents that could be affected by higher leakage. The 3.5 kΩ on resistance must be included in the sensor-source impedance calculation, and the 2 pC typical charge injection should be checked against the measurement settling window. The commercial 16-pin PDIP package also simplifies prototype wiring and through-hole instrument construction.

📏

Precision Measurement Front Ends

The MAX326CPE+ is suitable for precision measurement front ends where small leakage currents can disturb the reference node or sensor return path. Its four independently controlled SPST channels can isolate inputs during calibration, connect a known signal, and restore the measurement path without mechanical relay switching. The below-1 pA typical leakage reduces leakage-induced error, although the 3.5 kΩ on resistance can influence source impedance. Designers should also account for 2 pC typical charge injection and allow adequate settling before taking a reading.

🖥️

Automated Test Equipment

The MAX326CPE+ can serve as a low-leakage routing element in automated test equipment that connects DUT pins, test sources, and measurement channels. Four SPST paths provide useful channel density in a 16-pin PDIP package, while 10 pA maximum leakage helps preserve bias currents and high-impedance node voltages. The CMOS and TTL-compatible control interface supports conventional test-controller logic. For multiplexed fixtures, verify that 3.5 kΩ on resistance meets the allowable signal attenuation and that the 2 pC charge-injection transient remains acceptable to the selected measurement amplifier.

📊

Data Acquisition Systems

The MAX326CPE+ fits data-acquisition signal conditioning when a system must select or disconnect several low-level analog channels. Its four SPST switches allow a controller to route individual inputs while the below-1 pA typical leakage minimizes loading of high-impedance sensor networks. The device supports 10 V to 30 V single-supply or ±5 V to ±18 V dual-supply operation, enabling integration around laboratory and industrial acquisition equipment. Confirm the 3.5 kΩ channel resistance, account for 2 pC charge injection during selection transients, and follow the manufacturer truth table for control sequencing.

🔧

Laboratory Instrumentation

The MAX326CPE+ is appropriate for laboratory instrumentation that routes calibration signals to sensitive analog nodes. Ultra-low leakage helps prevent an open switch from creating a measurement error, while four channels in one package provide a compact through-hole implementation. The 10 V to 30 V single-supply and ±5 V to ±18 V dual-supply ranges support multiple bench-instrument signal levels. Because the on resistance is 3.5 kΩ, use it for high-impedance sensing paths rather than low-impedance driver outputs, and include the 2 pC typical charge injection in settling calculations.

🏭

Industrial Control Signal Isolation

The MAX326CPE+ can isolate low-current control and sensor paths in industrial systems where low off-state leakage is important. Its four SPST channels permit independent connection control, while CMOS and TTL-compatible inputs simplify interfacing with controller logic. The commercial-grade PDIP package supports repairable, through-hole control boards and avoids requiring a surface-mount rework process. Designers must verify that every analog signal remains within the supported single- or dual-supply range, consider the 3.5 kΩ channel resistance in the control-loop impedance budget, and observe all absolute-maximum ratings from the manufacturer datasheet.

Buod ng mga Inirekomendang Produkto

MAX326CPE+ Analog Devices Ginagamit sa: High-Impedance Sensor Routing, Precision Measurement Front Ends, Automated Test Equipment, Data Acquisition Systems, Laboratory Instrumentation, Industrial Control Signal Isolation MAX326CPE Same-core quad-SPST PDIP ordering variant Ginagamit sa: High-Impedance Sensor Routing, Precision Measurement Front Ends, Automated Test Equipment, Data Acquisition Systems, Laboratory Instrumentation, Industrial Control Signal Isolation
What is the MAX326CPE+?
The MAX326CPE+ is a four-channel CMOS analog switch with independently controlled SPST channels and ultra-low leakage. According to the Analog Devices MAX326 product page, each switch has 3.5 kΩ on resistance, leakage is specified at 10 pA maximum and below 1 pA typical, and the device is packaged in a 16-pin PDIP. It is intended for precision analog routing where off-state leakage must remain small.
What is the operating voltage of MAX326CPE+?
The MAX326CPE+ operates from 10 V to 30 V with a single supply and from ±5 V to ±18 V with dual supplies. The Analog Devices MAX326 product page identifies this quad-SPST CMOS device as compatible with both single- and dual-supply arrangements. Confirm the exact polarity and control-state requirements against the manufacturer pin description and truth table before connecting the device.
Why is the MAX326CPE+ suitable for high-impedance circuits?
The MAX326CPE+ is suitable for high-impedance circuits because its maximum leakage current is only 10 pA and its typical leakage is below 1 pA. According to the Analog Devices MAX326 product page, this ultra-low-leakage behavior limits current transfer through an open switch. That characteristic helps preserve small sensor, current-measurement, and precision analog signals that could otherwise be shifted by switch leakage.
What is the on resistance of MAX326CPE+?
The MAX326CPE+ has a specified on resistance of 3.5 kΩ. The Analog Devices MAX326 product page identifies the device as a quad, SPST, ultra-low-leakage CMOS analog switch with 3.5 kΩ on resistance. This resistance should be checked against the source impedance, signal bandwidth, and allowable attenuation requirements of the selected analog path.
Where can I download the MAX326CPE+ datasheet PDF?
The official MAX326 documentation is available from the Analog Devices product page at https://www.analog.com/en/products/max326.html. Select the MAX326 data sheet from the Documentation resources to obtain the authoritative electrical characteristics, pin description, truth table, package drawing, and ordering information. Use the manufacturer document for design sign-off rather than relying on secondary distributor summaries.
Where can I find the MAX326CPE+ pinout?
The MAX326CPE+ pinout is listed in the Pin Description section of the MAX326 manufacturer datasheet. The verified package information identifies a 16-pin PDIP device, but it does not include the individual terminal names or numbering. Use the pin-description table and package drawing on the official Analog Devices MAX326 page before assigning PCB traces or connecting control and analog signals.
What can replace the MAX326CPE+?
The closest verified same-package replacement is MAX326CPE, which differs from MAX326CPE+ only by the trailing ordering-code suffix and remains a 16-pin PDIP quad-SPST device. No five-part drop-in set was established from the available cross-reference results. For a new production design, verify the complete ordering code, lifecycle status, electrical limits, and marking requirements before substituting MAX326CPE.
Is MAX326CPE+ the same as MAX326CPE?
MAX326CPE and MAX326CPE+ describe the same core MAX326 quad-SPST CMOS switch in a 16-pin PDIP package, while the plus sign distinguishes the listed ordering variant. The distributor listing identifies both as 4-circuit, 1:1, 3.5 kΩ, 16-PDIP devices. Confirm whether the manufacturer treats the suffix as a temperature, packaging, or lead-free ordering code before using one in place of the other.
MAX326CPE+ vs MAX326CPE - which one should I choose?
Choose MAX326CPE+ when its verified ordering code matches the required manufacturer part number, and confirm MAX326CPE only when that suffix is accepted by your BOM and qualification process. Both listings identify a four-channel, SPST, 3.5 kΩ, 16-pin PDIP device. Because the distinction may involve ordering or qualification attributes, use the manufacturer data sheet and current product-page ordering table for final approval.
When should I choose MAX326CPE+ over another quad SPST switch?
Choose MAX326CPE+ when the design requires four SPST channels, a 16-pin PDIP footprint, 3.5 kΩ on resistance, and leakage no greater than 10 pA. It is especially relevant to high-impedance instrumentation where the typical leakage is below 1 pA. If a candidate uses a surface-mount package or lacks the required voltage range, it is not a drop-in replacement and would require a different PCB footprint.
Is MAX326CPE+ suitable for precision measurement systems?
Yes, the MAX326CPE+ is suitable for precision measurement systems that can tolerate a 3.5 kΩ on resistance and benefit from leakage below 1 pA typical. Its four SPST channels can route or isolate high-impedance sensor paths, while the 2 pC typical charge injection should be included in acquisition-settling calculations. The 10 V to 30 V single-supply range also supports laboratory and industrial signal-routing systems.
How much charge injection does MAX326CPE+ have?
The MAX326CPE+ has 2 pC typical charge injection, according to the Analog Devices MAX326 product page. This value represents the unwanted charge coupled into the switched signal when a control input changes state. In high-gain or fast-settling systems, include the control-edge timing and downstream filtering when evaluating whether that injected charge creates an acceptable transient.
Does MAX326CPE+ support TTL-compatible control signals?
Yes, the MAX326CPE+ provides CMOS and TTL-compatible control interfacing. The Analog Devices MAX326 product page identifies both compatibility types and describes the device as a quad, SPST, ultra-low-leakage CMOS analog switch. Use the data sheet's control-input thresholds for the selected supply voltage to confirm that the chosen driver meets the required logic levels.
Where can I buy MAX326CPE+ and check its lead time?
Use the Request a Quote form on this page to request MAX326CPE+ availability, lead time, and order quantities from XAIPART. The current purchasing response should be confirmed through that form because stock and delivery schedules can change. The part is listed as a commercial-grade, 16-pin PDIP quad-SPST analog switch suitable for through-hole assembly.
What is the price and stock status of MAX326CPE+?
Current pricing and stock for MAX326CPE+ should be obtained through the Request a Quote form on this page. The verified marketplace excerpts identify the exact MPN as an active quad-SPST, 3.5 kΩ, 16-pin PDIP device, but they do not provide a qualifying quantity-break table or a dependable stock count. Request the exact suffix and required shipment quantity for an actionable quotation.
What are the key specifications of MAX326CPE+ that engineers should know?
The key MAX326CPE+ specifications are four SPST channels, 3.5 kΩ on resistance, 10 pA maximum leakage, below 1 pA typical leakage, 2 pC typical charge injection, and CMOS/TTL-compatible controls. The Analog Devices MAX326 product page specifies 10 V to 30 V single-supply operation, ±5 V to ±18 V dual-supply operation, and a 16-pin PDIP package for through-hole assembly.
What is the best Analog Devices equivalent for MAX326CPE+?
The best verified Analog Devices equivalent is MAX326CPE, which is listed as a four-circuit, 1:1, 3.5 kΩ, 16-PDIP device matching the MAX326CPE+ core configuration. No separate cross-brand drop-in candidate was established by the available comparison data, so no unsupported manufacturer recommendation is made. Validate the suffix and current ordering status before using MAX326CPE as a production substitute.

Impormasyon ng Talumpati sa Engineering for MAX326CPE+ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose MAX326CPE+ for a four-channel SPST routing design that specifically requires a 16-pin PDIP footprint, 3.5 kΩ on resistance, and ultra-low leakage. Its below-1 pA typical leakage is especially useful for high-impedance sensors, precision current measurements, and calibration nodes where off-state current would distort the result. MAX326CPE is the closest verified same-package alternative because its distributor listing identifies the same four-channel, 1:1, 3.5 kΩ, 16-PDIP configuration; approve that suffix only after confirming its current electrical table and ordering status. Do not select a generic quad-SPST device unless it also matches the SPST behavior, control truth table, voltage ratings, leakage, and exact pin assignment. A surface-mount alternative is not a drop-in option because the PCB footprint would require redesign.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MAX326CPE
Package 16-pin PDIP 16-pin PDIP
Brand Analog Devices Analog Devices
Number of Switches 4 circuits 4 circuits
Switch Configuration 1:1 SPST 1:1 SPST
On Resistance 3.5 kΩ 3.5 kΩ
Mounting Type Through-hole Through-hole

Pangunahing mga Pagkakaiba

  • Ultra-low leakage supports preservation of small high-impedance signals (kumpara saMAX326CPE)
  • Four independently controlled channels in one package (kumpara saMAX326CPE)
  • Broad single- and dual-supply operating ranges (kumpara saMAX326CPE)

Talaan ng Disenyo

Treat the 3.5 kΩ on resistance as part of the source impedance presented to the switched node. It is generally appropriate for high-impedance sensing paths but may create excessive attenuation or phase shift when driving a low-impedance load. Simulate the complete source, switch, cable, and input-impedance network, and include the 2 pC typical charge injection when evaluating transient settling after a control transition.

Route the high-impedance analog terminals away from switching nodes, clock lines, and digital return currents. Keep the MAX326CPE+ control traces short enough to avoid false switching, use a solid ground reference, and place any required bypass capacitors close to the supply pins according to the manufacturer application guidance. Because the PDIP package exposes all terminals, inspect solder bridges and contamination on closely spaced analog and control pins after assembly.

Do not assume that every quad-SPST switch with a 16-pin PDIP outline is interchangeable. The switch type, normally closed or normally open behavior, on resistance, leakage, supply range, absolute maximum ratings, and truth table must all match. In particular, verify control polarity and the switched terminals in the MAX326 pin-description table before assigning PCB nets, because the available package summary does not expose the complete pin numbering.

Confirm whether the application uses the supported 10 V to 30 V single-supply range or the ±5 V to ±18 V dual-supply range. Keep all analog and logic voltages within their respective absolute maximum limits, especially during power-up, shutdown, and fault conditions. Provide a defined logic state before the analog node becomes active, because an uncontrolled control input could leave a sensitive measurement path connected or disconnected unexpectedly.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The MAX326CPE+ is listed as a commercial-grade component, but the verified excerpts do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not indicated for this commercial-grade part.

Kaugnay na Hanapin

MAX326CPE+ datasheet MAX326CPE+ pinout MAX326CPE+ datasheet pdf Analog Devices MAX326CPE+ MAX326CPE+ equivalent MAX326CPE+ replacement MAX326CPE+ cross reference MAX326CPE+ vs MAX326CPE MAX326CPE+ 3.5kOhm SPST MAX326CPE+ 16-pin PDIP MAX326CPE+ low leakage switch MAX326CPE+ price MAX326CPE+ stock MAX326CPE+ analog switch MAX326CPE+ footprint

Mga kaugnay na Mga Komponente at mga Tuntunin

Analog Devices MAX326CPE+ MAX326CPE MAX326 CMOS analog switch SPST switch four-channel analog switch integrated circuit interface IC semiconductor ultra-low leakage 10 pA maximum leakage 3.5 kΩ on resistance 2 pC charge injection 16-pin PDIP DIP package through-hole assembly CMOS-compatible control TTL-compatible control high-impedance measurement sensor routing data acquisition single-supply operation dual-supply operation
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ