Analog Devices

MAX332CPE+ - Quad SPST 175Ω Analog Switch | Analog Devices

MPN: MAX332CPE+ ✓ Active
175 Ω Rds(on) 16-pin PDIP Package
MOQ: 1 |

MAX332CPE+ Overview

The Analog Devices MAX332CPE+ is a four-circuit, normally open analog switch with a 175Ω on-resistance, packaged in a 16-pin PDIP. It provides 1:1 signal routing, a typical turn-on time of 1 µs, and a typical turn-off time of 500 ns, making it suitable for analog and digital signal-path switching.

An analog switch is a semiconductor device that connects or disconnects a signal path under digital control. Within the component hierarchy, the MAX332CPE+ is an analog switch, also classified as a multiplexer or demultiplexer when used to route one of several lines to a common node. Its four independent SPST switches can isolate, select, or disconnect external circuit nodes.

The MAX332CPE+ uses four normally open switch circuits to provide straightforward routing without a break-before-make interpretation in the product description. Its documented 175Ω on-resistance supports practical signal interconnection, while 1 µs turn-on and 500 ns turn-off timing suit control systems that need switching in the microsecond range. The 16-pin PDIP format supports conventional through-hole PCB assembly.

The device is identified as a quad SPST, 1:1 analog switch with a 16-pin PDIP package. Its four-circuit architecture consolidates multiple switch functions into one package, reducing component count compared with four single-switch devices. The device is implemented as a CMOS analog switch and is intended for controlled routing of external signals rather than power conversion or high-current switching.

Typical uses include signal-path isolation in test and measurement equipment, channel selection in analog front ends, sample-and-hold control paths, instrumentation interfaces, and industrial control systems. In each case, the control logic selects one of the available connections while the switch network separates the selected source from the other external nodes.

Designers should verify the exact control states, pin mapping, supply requirements, allowable signal levels, and switching conditions in the Maxim Integrated datasheet before laying out a PCB. The PDIP package is mechanically straightforward to route, but the switch nodes should be positioned to minimize coupling between adjacent high-impedance paths and to keep control traces away from sensitive analog conductors.

This product page combines the confirmed switch configuration, timing, resistance, and package characteristics with application guidance, engineering considerations, and drop-in alternatives. It is designed to help engineers identify the correct device faster while preserving the distinction between verified MAX332CPE+ attributes and replacement-specific data that must be checked before procurement.

Drop-in alternatives for MAX332CPE+ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

MAX330CPE+

✅ Drop-In ⚠️ Specs Unverified
📦 16-pin PDIP
Retains 4 normally open SPST circuits and 16-pin PDIP format; on-resistance, timing, leakage, and control-polarity differences are

📋 Reference alternative (not in catalog)

MAX331CPE+

✅ Drop-In ⚠️ Specs Unverified
📦 16-pin PDIP
Retains 4 normally open SPST circuits and 16-pin PDIP format; MAX332CPE+ is documented at 175 Ω, while the alternative on-resistance difference is

📋 Reference alternative (not in catalog)

MAX333CPE+

✅ Drop-In ⚠️ Specs Unverified
📦 16-pin PDIP
Retains 4 normally open SPST circuits and 16-pin PDIP format; on-resistance, timing, leakage, and control-polarity differences are

📋 Reference alternative (not in catalog)

MAX334CPE+

✅ Drop-In ⚠️ Specs Unverified
📦 16-pin PDIP
Retains 4 normally open SPST circuits and 16-pin PDIP format; on-resistance, timing, leakage, and control-polarity differences are

📋 Reference alternative (not in catalog)

MAX335CPE+

✅ Drop-In ⚠️ Specs Unverified
📦 16-pin PDIP
Retains 4 normally open SPST circuits and 16-pin 有的 PDIP format; on-resistance, timing, leakage, and control-polarity differences are

📋 Reference alternative (not in catalog)

MAX332CPE+ Maximum Ratings & Electrical Characteristics

Number of Switch Circuits 4 circuits
Switch Configuration Quad SPST
Switch Type Normally open
Signal Routing Ratio 1:1
On-Resistance 175 Ω
Typical Turn-On Time 1 µs
Typical Turn-Off Time 500 ns
Charge Injection 20 pC
Package 16-pin PDIP
Package Width 0.300 inch (7.62 mm)
Mounting Type Through-hole
Technology CMOS analog switch
Category Analog switch / multiplexer / demultiplexer

MAX332CPE+ 0.300 inch (7.62 mm) Pin Configuration Guide

Pin configuration for MAX332CPE+ (0.300 inch (7.62 mm) package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

0.300 inch (7.62 mm) package pinout diagram for MAX332CPE+

No detailed pinout data available for MAX332CPE+.

Refer to the datasheet for full pin configuration.

Typical Applications

MAX332CPE+ is suitable for 6 applications: Instrument Signal Isolation, Analog Test Fixture Routing, Sensor Channel Selection, Control Output Isolation, Audio Signal Routing, Communications Line Isolation.

🖥️

Instrument Signal Isolation

The MAX332CPE+ fits instrumentation designs that need to connect and disconnect measurement paths without using four separate switch packages. Its four normally open SPST circuits can isolate sensor lines, attenuator stages, or buffer inputs, while the documented 175Ω on-resistance establishes the series resistance present in the closed path. Typical turn-on and turn-off times of 1 µs and 500 ns allow the control system to change routes on a microsecond time scale. Keep sensitive source nodes short and away from digital control traces to limit injected coupling, and confirm the allowable signal amplitude and off-state leakage against the Maxim Integrated datasheet before finalizing the instrumentation front end.

🔧

Analog Test Fixture Routing

A MAX332CPE+ can be used in automated test fixtures to route a common test resource toward one of several DUT connections while isolating the other channels. Four independently controlled SPST switches provide a practical way to organize source, measurement, and guard paths in a 16-pin PDIP package. The 175Ω on-resistance is relevant when the test path includes high source impedance, while the 1 µs turn-on time supports relatively quick fixture changes between test phases. Place the switch close to the fixture connector when practical, provide a low-impedance return path, and verify that injected charge of 20 pC remains acceptable for the measured node and settling requirements.

🏭

Sensor Channel Selection

The MAX332CPE+ is suitable for selecting or disconnecting low-level sensor channels in industrial monitoring and data-acquisition systems. Its four normally open circuits can isolate unused sensors, create switched sensor connections, or separate stages that would otherwise remain coupled. The 175Ω on-resistance should be evaluated against the sensor source impedance and amplifier input bias requirements, and the 20 pC charge-injection figure must be checked against the required settling time after each transition. Use a stable reference and ground arrangement at the sensor interface, while keeping switch-control signals isolated from the sensitive sensor conductors.

⚡

Control Output Isolation

The MAX332CPE+ can be placed between a controller and external equipment when four independently isolatable output paths are required. Although it is an analog switch rather than a relay, its 1 µs typical turn-on time and 500 ns typical turn-off time suit low-power control and signal-routing functions. The 175Ω series resistance should not be ignored when driving a sensitive load, and the device should remain within its documented signal and supply limits. Place the IC near the connector or interface circuitry to keep switch loops compact, provide a low-impedance supply decoupling path, and verify that the normally open behavior matches the required default-safe connection state.

🎧

Audio Signal Routing

The MAX332CPE+ can support auxiliary routing in audio and communication equipment where four low-level signal paths must be isolated or selected. Its four SPST circuits can manage monitor, mute, test, or auxiliary connections, while the 175Ω on-resistance may be acceptable for low-impedance audio paths. The 20 pC charge injection and 1 µs turn-on time should be evaluated when switching is audible or when the output drives a high-impedance amplifier. Keep the routing loops short, maintain a common ground reference, and use the Maxim Integrated datasheet to verify the maximum signal amplitude, off-state behavior, and operating conditions before selecting it for a precision audio path.

🌐

Communications Line Isolation

The MAX332CPE+ can be used in communications equipment for auxiliary line isolation, test-point routing, or interface-segment separation where four normally open SPST paths are adequate. It is not an RS-232 transceiver and should not be confused with a MAX3232-family device. The 175Ω on-resistance, 500 ns typical turn-off time, and 20 pC charge injection determine how the switch affects the connected line. Place the device near the line interface, avoid long parallel routes between switched and unswitched conductors, and verify bandwidth, allowable signal level, and leakage from the datasheet before using it in a communication path.

What is the MAX332CPE+?
The MAX332CPE+ is a four-circuit, normally open SPST analog switch with a documented 175Ω on-resistance in a 16-pin PDIP package. According to the Maxim Integrated datasheet and distributor specifications, it performs 1:1 signal routing and is intended for isolation, selection, and disconnect functions in analog and control circuits. Its four switch circuits are consolidated into one through-hole package.
What are the key specifications of MAX332CPE+ that engineers should know?
The MAX332CPE+ provides four normally open SPST circuits, 175Ω on-resistance, 1 µs typical turn-on time, and 500 ns typical turn-off time in a 16-pin PDIP package. According to the Maxim Integrated datasheet, it is a CMOS analog switch with a 20 pC typical charge-injection figure. These characteristics make it suitable for general signal routing, test equipment, instrumentation, and industrial control applications.
Where can I download the MAX332CPE+ datasheet PDF?
The MAX332CPE+ datasheet PDF is available from the manufacturer-linked documentation listed on this page, with a direct PDF copy also available from the listed technical document source. Use the Maxim Integrated datasheet to confirm the pin configuration, control logic, absolute maximum ratings, electrical characteristics, and recommended operating conditions before committing the PCB layout.
Where can I find the MAX332CPE+ pinout?
The MAX332CPE+ uses a 16-pin PDIP package, and its complete pin assignment is shown in the Maxim Integrated datasheet. The switch, common, control, ground, and supply connections must be assigned exactly as documented rather than inferred from a generic quad-switch layout. Review the pin-description table and typical connection diagram before assigning PCB tracks.
Can MAX332CPE+ be used for signal isolation and test equipment?
Yes, the MAX332CPE+ is well suited to signal isolation and test-equipment routing because it contains four normally open SPST circuits with a 175Ω on-resistance. According to the Maxim Integrated datasheet, typical switching times are 1 µs turn-on and 500 ns turn-off. These values support controlled isolation of instrument channels, sensor inputs, and external test fixtures.
What is the difference between MAX332CPE+ and MAX331CPE+?
The MAX332CPE+ and MAX331CPE+ are closely related four-channel SPST CMOS analog switches in the same PDIP package family, so their architectural roles are similar. Their exact on-resistance, charge-injection, timing, and operating-condition differences must be compared in the respective Maxim Integrated datasheets. The MAX332CPE+ is documented at 175Ω on-resistance, 1 µs turn-on, and 500 ns turn-off.
When should I choose MAX332CPE+ over another quad SPST switch?
Choose the MAX332CPE+ when a design needs four normally open SPST channels, a 175Ω on-resistance, microsecond-scale switching, and a 16-pin PDIP footprint. It is particularly suitable for through-hole instrumentation, analog test paths, and industrial control boards. Confirm supply voltage, signal-range limits, control polarity, leakage, and channel isolation against the datasheet before final selection.
Is MAX332CPE+ suitable for industrial control applications?
The MAX332CPE+ can fit industrial control applications that use low-level signal routing rather than high-current or high-voltage switching. Its four normally open SPST circuits can isolate sensors, test points, or control paths, and its documented 1 µs turn-on and 500 ns turn-off times provide defined switching behavior. Confirm operating temperature and electrical limits in the datasheet.
What can replace MAX332CPE+?
The closest documented replacements are same-family, 16-pin PDIP quad SPST CMOS switches from Analog Devices, including MAX330CPE+, MAX331CPE+, MAX333CPE+, MAX334CPE+, and MAX335CPE+. They must be verified against the MAX332CPE+ datasheet for control logic, pin assignment, supply voltage, on-resistance, leakage, and signal-range compatibility before being treated as drop-in replacements.
Is MAX332CPE+ the same as MAX3232CPE+?
No. The MAX332CPE+ is a four-circuit analog switch with a 175Ω on-resistance, whereas the MAX3232CPE+ is an RS-232 transceiver. Their functions and internal architectures are different even though both are available in 16-pin PDIP packages. The MAX3232CPE+ should not be used as a substitute for the MAX332CPE+ because its pins and signal interface are not equivalent.
Where to buy MAX332CPE+ online?
Use the Request a Quote form on this page to request MAX332CPE+ availability, lead time, and a current quotation. The request should identify the exact MAX332CPE+ ordering code and the 16-pin PDIP package. The form provides a single channel for obtaining commercial confirmation without relying on a static price or stock statement that may change.
What is the price of MAX332CPE+?
The current price of MAX332CPE+ should be requested through the Request a Quote form on this page. A precise quotation depends on quantity, delivery location, and market conditions. Because prices change frequently, the form is the appropriate place to obtain a current commercial figure for the exact MAX332CPE+ part number and 16-pin PDIP package.
What is the lead time for MAX332CPE+?
Request the current MAX332CPE+ lead time through the Request a Quote form on this page. Include the required quantity and destination so the commercial response reflects the appropriate fulfillment conditions. The 16-pin PDIP package and exact MAX332CPE+ suffix should be stated on the request to avoid ambiguity with related catalog variants.
Is MAX332CPE+ in stock?
Current MAX332CPE+ stock status should be confirmed through the Request a Quote form on this page. The form allows the requested quantity and delivery location to be included in the availability response. For production planning, also request the manufacturer or authorized-channel lead time rather than treating a temporary listing status as a scheduled allocation.
How should the MAX332CPE+ PCB layout be designed?
Route each switch path directly to its associated external node and keep the normally open switch terminals away from unrelated high-impedance inputs. Place control traces and ground returns to minimize coupling into analog signal paths, especially where the 175Ω on-resistance is acceptable but source impedance is high. Follow the Maxim Integrated datasheet for the exact pin map and recommended connection diagram.

Engineering reference data for MAX332CPE+ — comparison, design guidance, and compliance information.

Selection Guide

Choose the MAX332CPE+ when the board needs four normally open SPST routing points in a 16-pin PDIP package and the design can accommodate its documented 175Ω on-resistance. It is especially useful for test fixtures, instrumentation, sensor-channel isolation, and auxiliary signal routing where 1 µs turn-on and 500 ns turn-off behavior are sufficient. Evaluate MAX330CPE+ or MAX331CPE+ when their respective on-resistance, leakage, timing, control polarity, and supply characteristics better match the source impedance or settling requirement. MAX333CPE+, MAX334CPE+, and MAX335CPE+ provide other family members to consider when their electrical characteristics improve a specific channel. Do not substitute an RS-232 transceiver such as the MAX3232CPE+ because the device function and pin interface are different. For every candidate, verify the complete pin map, absolute maximum ratings, control logic, and operating conditions before approving a drop-in replacement.

Comparison with Alternatives

Parameter This Product MAX330CPE+ MAX331CPE+ MAX333CPE+ MAX334CPE+ MAX335CPE+
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP
Number of Switch Circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits
Switch Configuration Quad SPST Quad SPST Quad SPST Quad SPST Quad SPST Quad SPST
Signal Routing Ratio 1:1 1:1 1:1 1:1 1:1 1:1
Mounting Type Through-hole Through-hole Through-hole Through-hole Through-hole Through-hole

Key Differentiators

  • Four switch functions in one through-hole package (vs MAX331CPE+)
  • Documented 175Ω on-resistance (vs MAX330CPE+)
  • Defined microsecond-scale switching behavior (vs MAX333CPE+)

Design Notes

Treat each closed switch path as a 175Ω series element when calculating signal attenuation and loading. For a high-impedance source this resistance may have little effect, but it can divide a signal with a significantly lower source impedance. Use the Maxim Integrated datasheet to check the on-resistance test conditions, because the specified 175Ω value should not be generalized across supply, temperature, or signal-amplitude conditions that differ from those conditions.

Keep switched analog nodes short and avoid routing them parallel to digital control or clock lines. If the control traces must cross an analog path, use a perpendicular crossing where practical and provide a continuous ground reference. Place supply decoupling at the device pins and maintain the pin orientation defined in the Maxim Integrated datasheet so the 16-pin PDIP footprint is not mirrored during assembly.

Do not treat the MAX332CPE+ as a power switch or as an RS-232 transceiver. The documented 175Ω on-resistance is not intended to imply low-loss high-current operation, and the 20 pC charge injection can create a transient voltage step on a high-impedance node. Check the maximum switched voltage, current, supply range, leakage, control polarity, and operating-temperature limits before applying the device to a new circuit.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The MAX332CPE+ is an analog interface switch rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer or the relevant declaration.

Related Searches

MAX332CPE+ datasheet MAX332CPE+ pinout MAX332CPE+ datasheet pdf MAX332CPE+ specifications MAX332CPE+ equivalent MAX332CPE+ replacement MAX332CPE+ cross reference MAX332CPE+ price MAX332CPE+ stock Analog Devices MAX332CPE+ MAX332CPE+ 175 ohm switch MAX332CPE+ PDIP-16 MAX332CPE+ signal isolation MAX332CPE+ vs MAX331CPE+

Related Components & Terms

Analog Devices Maxim Integrated MAX332CPE+ MAX330CPE+ MAX331CPE+ MAX333CPE+ MAX334CPE+ MAX335CPE+ analog switch multiplexer demultiplexer SPST switch normally open switch CMOS analog switch signal isolation test fixture routing sensor channel selection on-resistance charge injection turn-on time turn-off time 16-pin PDIP PDIP package family through-hole mounting 175 ohm
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details