MAX332CPE+ - Quad SPST 175Ω Analog Switch | Analog Devices
Teilenummer: MAX332CPE+ ✓ AktivMAX332CPE+ Übersicht
An analog switch is a semiconductor device that connects or disconnects a signal path under digital control. Within the component hierarchy, the MAX332CPE+ is an analog switch, also classified as a multiplexer or demultiplexer when used to route one of several lines to a common node. Its four independent SPST switches can isolate, select, or disconnect external circuit nodes.
The MAX332CPE+ uses four normally open switch circuits to provide straightforward routing without a break-before-make interpretation in the product description. Its documented 175Ω on-resistance supports practical signal interconnection, while 1 µs turn-on and 500 ns turn-off timing suit control systems that need switching in the microsecond range. The 16-pin PDIP format supports conventional through-hole PCB assembly.
The device is identified as a quad SPST, 1:1 analog switch with a 16-pin PDIP package. Its four-circuit architecture consolidates multiple switch functions into one package, reducing component count compared with four single-switch devices. The device is implemented as a CMOS analog switch and is intended for controlled routing of external signals rather than power conversion or high-current switching.
Typical uses include signal-path isolation in test and measurement equipment, channel selection in analog front ends, sample-and-hold control paths, instrumentation interfaces, and industrial control systems. In each case, the control logic selects one of the available connections while the switch network separates the selected source from the other external nodes.
Designers should verify the exact control states, pin mapping, supply requirements, allowable signal levels, and switching conditions in the Maxim Integrated datasheet before laying out a PCB. The PDIP package is mechanically straightforward to route, but the switch nodes should be positioned to minimize coupling between adjacent high-impedance paths and to keep control traces away from sensitive analog conductors.
This product page combines the confirmed switch configuration, timing, resistance, and package characteristics with application guidance, engineering considerations, and drop-in alternatives. It is designed to help engineers identify the correct device faster while preserving the distinction between verified MAX332CPE+ attributes and replacement-specific data that must be checked before procurement.
Drop-in-Alternativen für MAX332CPE+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
MAX330CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX331CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX333CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX334CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX335CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX332CPE+ Grenzwerte & elektrische Eigenschaften
| Number of Switch Circuits | 4 circuits |
| Switch Configuration | Quad SPST |
| Switch Type | Normally open |
| Signal Routing Ratio | 1:1 |
| On-Resistance | 175 Ω |
| Typical Turn-On Time | 1 µs |
| Typical Turn-Off Time | 500 ns |
| Charge Injection | 20 pC |
| Gehäuse | 16-pin PDIP |
| Package Width | 0.300 inch (7.62 mm) |
| Montageart | Through-hole |
| Technology | CMOS analog switch |
| Kategorie | Analog switch / multiplexer / demultiplexer |
MAX332CPE+ 0.300 inch (7.62 mm) Pinbelegungsleitfaden
Pinbelegung für MAX332CPE+ (0.300 inch (7.62 mm)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für MAX332CPE+.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MAX332CPE+ ist geeignet für 6 Anwendungs: Instrument Signal Isolation, Analog Test Fixture Routing, Sensor Channel Selection, Control Output Isolation, Audio Signal Routing, Communications Line Isolation.
Instrument Signal Isolation
The MAX332CPE+ fits instrumentation designs that need to connect and disconnect measurement paths without using four separate switch packages. Its four normally open SPST circuits can isolate sensor lines, attenuator stages, or buffer inputs, while the documented 175Ω on-resistance establishes the series resistance present in the closed path. Typical turn-on and turn-off times of 1 µs and 500 ns allow the control system to change routes on a microsecond time scale. Keep sensitive source nodes short and away from digital control traces to limit injected coupling, and confirm the allowable signal amplitude and off-state leakage against the Maxim Integrated datasheet before finalizing the instrumentation front end.
Analog Test Fixture Routing
A MAX332CPE+ can be used in automated test fixtures to route a common test resource toward one of several DUT connections while isolating the other channels. Four independently controlled SPST switches provide a practical way to organize source, measurement, and guard paths in a 16-pin PDIP package. The 175Ω on-resistance is relevant when the test path includes high source impedance, while the 1 µs turn-on time supports relatively quick fixture changes between test phases. Place the switch close to the fixture connector when practical, provide a low-impedance return path, and verify that injected charge of 20 pC remains acceptable for the measured node and settling requirements.
Sensor Channel Selection
The MAX332CPE+ is suitable for selecting or disconnecting low-level sensor channels in industrial monitoring and data-acquisition systems. Its four normally open circuits can isolate unused sensors, create switched sensor connections, or separate stages that would otherwise remain coupled. The 175Ω on-resistance should be evaluated against the sensor source impedance and amplifier input bias requirements, and the 20 pC charge-injection figure must be checked against the required settling time after each transition. Use a stable reference and ground arrangement at the sensor interface, while keeping switch-control signals isolated from the sensitive sensor conductors.
Control Output Isolation
The MAX332CPE+ can be placed between a controller and external equipment when four independently isolatable output paths are required. Although it is an analog switch rather than a relay, its 1 µs typical turn-on time and 500 ns typical turn-off time suit low-power control and signal-routing functions. The 175Ω series resistance should not be ignored when driving a sensitive load, and the device should remain within its documented signal and supply limits. Place the IC near the connector or interface circuitry to keep switch loops compact, provide a low-impedance supply decoupling path, and verify that the normally open behavior matches the required default-safe connection state.
Audio Signal Routing
The MAX332CPE+ can support auxiliary routing in audio and communication equipment where four low-level signal paths must be isolated or selected. Its four SPST circuits can manage monitor, mute, test, or auxiliary connections, while the 175Ω on-resistance may be acceptable for low-impedance audio paths. The 20 pC charge injection and 1 µs turn-on time should be evaluated when switching is audible or when the output drives a high-impedance amplifier. Keep the routing loops short, maintain a common ground reference, and use the Maxim Integrated datasheet to verify the maximum signal amplitude, off-state behavior, and operating conditions before selecting it for a precision audio path.
Communications Line Isolation
The MAX332CPE+ can be used in communications equipment for auxiliary line isolation, test-point routing, or interface-segment separation where four normally open SPST paths are adequate. It is not an RS-232 transceiver and should not be confused with a MAX3232-family device. The 175Ω on-resistance, 500 ns typical turn-off time, and 20 pC charge injection determine how the switch affects the connected line. Place the device near the line interface, avoid long parallel routes between switched and unswitched conductors, and verify bandwidth, allowable signal level, and leakage from the datasheet before using it in a communication path.
Technische Referenzdaten für MAX332CPE+ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX330CPE+ | MAX331CPE+ | MAX333CPE+ | MAX334CPE+ | MAX335CPE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Number of Switch Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | Quad SPST | Quad SPST | Quad SPST | Quad SPST | Quad SPST | Quad SPST |
| Signal Routing Ratio | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
Wichtigste Unterscheidungsmerkmale
- Four switch functions in one through-hole package (vs. MAX331CPE+)
- Documented 175Ω on-resistance (vs. MAX330CPE+)
- Defined microsecond-scale switching behavior (vs. MAX333CPE+)
Designhinweise
Treat each closed switch path as a 175Ω series element when calculating signal attenuation and loading. For a high-impedance source this resistance may have little effect, but it can divide a signal with a significantly lower source impedance. Use the Maxim Integrated datasheet to check the on-resistance test conditions, because the specified 175Ω value should not be generalized across supply, temperature, or signal-amplitude conditions that differ from those conditions.
Keep switched analog nodes short and avoid routing them parallel to digital control or clock lines. If the control traces must cross an analog path, use a perpendicular crossing where practical and provide a continuous ground reference. Place supply decoupling at the device pins and maintain the pin orientation defined in the Maxim Integrated datasheet so the 16-pin PDIP footprint is not mirrored during assembly.
Do not treat the MAX332CPE+ as a power switch or as an RS-232 transceiver. The documented 175Ω on-resistance is not intended to imply low-loss high-current operation, and the 20 pC charge injection can create a transient voltage step on a high-impedance node. Check the maximum switched voltage, current, supply range, leakage, control polarity, and operating-temperature limits before applying the device to a new circuit.
Compliance-Informationen
The MAX332CPE+ is an analog interface switch rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer or the relevant declaration.