MAX336EPI+ - 16:1 Low-Leakage CMOS Multiplexer | Analog Devices
MPN: MAX336EPI+ ✓ ActiveMAX336EPI+ Overview
An analog multiplexer is an input-routing semiconductor that selects one of several analog inputs and connects it to a common output. The MAX336 belongs to the CMOS analog switch and multiplexer hierarchy within broader interface ICs. Its 16:1 configuration reduces the number of physical signal paths required in instrumentation, measurement, control, and data-acquisition systems where many sensor or test inputs must be scanned sequentially.
Key features include a single 16:1 configuration, 400 ohm on-resistance, low-leakage CMOS operation, and a 4.5 V to 30 V single-supply range. The MAX336 family also provides a dual 8-channel configuration option and is specified for low charge injection, with 3.5 pC typical. According to the Analog Devices product page, electrostatic-discharge protection exceeds 2000 V using method 3015.7, helping protect sensitive analog nodes during handling and system integration.
The MAX336 is implemented as a CMOS analog switch with controlled complementary addressing and break-before-make behavior expected of the MAX336/MAX337 family. Its low-leakage characteristic is particularly valuable when measuring high-impedance sources because off-channel leakage can create an error proportional to source impedance. The 400 ohm on-resistance must also be included in source-impedance and gain-error calculations, especially for instrumentation front ends with long sensor leads.
Typical uses include battery-cell monitoring, programmable instrumentation, industrial control, automated test equipment, data acquisition, and analog signal routing. The device can consolidate 16 measurement channels into one signal chain while the surrounding system applies an address and measures each selected input. It is also suitable where leakage, rather than switching speed, is the primary concern.
PCB design should keep the selected analog path short and place protection and filtering components near the relevant pins. Verify input levels, supply range, address timing, and off-channel leakage against the end-equipment accuracy budget. A PDIP package favors through-hole prototyping and repair but occupies more board area than surface-mount alternatives.
This product page combines manufacturer specifications, package information, sourcing guidance, application analysis, and honest replacement evaluation. It also highlights where pin-to-pin alternatives are technically credible, avoiding the inclusion of parts that require a different footprint or materially different switching architecture.
Drop-in alternatives for MAX336EPI+ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
MAX336EPI
✅ Drop-In📋 Reference alternative (not in catalog)
MAX337EPI+
✅ Drop-In📋 Reference alternative (not in catalog)
MAX336EPI+ Specifications
| Product Type | 16:1 CMOS analog multiplexer |
| Number of Channels | 16 channels |
| Configuration | Single 16:1 |
| On-Resistance | 400 ohm |
| Supply Voltage Range | 4.5 V to 30 V |
| Dual-Supply Operation | Plus or minus 4.5 V to plus or minus 20 V |
| Charge Injection | 3.5 pC typical |
| ESD Protection | Greater than 2000 V using method 3015.7 |
| Multiplexer Family | 16-channel or dual 8-channel configuration |
| Switch Type | CMOS analog switch |
| Leakage Characteristic | Low leakage |
| Package | 28-pin PDIP |
| Mounting Type | Through-hole |
MAX336EPI+ 28-pin pdip Pin Configuration Guide
Pin configuration for MAX336EPI+ (28-pin pdip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MAX336EPI+.
Refer to the datasheet for full pin configuration.
Typical Applications
MAX336EPI+ is suitable for 6 applications: Battery-Cell Monitoring, Programmable Test and Measurement, Industrial Process Sensing, Data-Acquisition Systems, Automated Test Equipment, Analog Signal Routing.
Battery-Cell Monitoring
The MAX336EPI+ is useful for scanning groups of battery-cell voltages through a common measurement path. Its single 16:1 organization can route 16 monitored inputs in a repeated sequence, reducing the number of analog input channels required in the measuring system. The 4.5 V to 30 V supply range supports equipment operating from multiple cell stacks, while the 400 ohm on-resistance must be included in the input-loading analysis. For high-impedance cell taps, the family's low-leakage characteristic helps prevent off-channel paths from corrupting measurements.
Recommended
Programmable Test and Measurement
A programmable instrument can use the MAX336EPI+ to connect one of 16 external test points to a shared measurement chain. This arrangement supports repeatable channel selection without requiring 16 separate analog front ends. The 16:1 architecture reduces routing complexity, while the 400 ohm on-resistance should be combined with the source impedance of the device under test when calculating measurement accuracy. The low-leakage behavior is advantageous when switching between high-impedance sensors, probes, or precision networks.
Recommended
Industrial Process Sensing
The MAX336EPI+ can scan pressure, temperature, level, or current-derived analog signals in an industrial control system. A single 16:1 multiplexer allows one controller ADC channel to service multiple sensors, lowering wiring and input-converter requirements. Its 4.5 V to 30 V operating range supports industrial supply conditions, while the family low-leakage characteristic helps preserve accuracy with resistive sensors. Engineers should verify common-mode limits, settling behavior, and channel-to-channel isolation for the process signals being selected.
Recommended
Data-Acquisition Systems
The MAX336EPI+ fits data-acquisition systems that must monitor many slowly changing analog inputs with a shared converter. Its single 16:1 configuration consolidates 16 channels into one routing stage, and the 400 ohm on-resistance can be incorporated into the input model used for gain and settling calculations. The low-leakage characteristic is particularly useful for high-impedance transducers, where leakage through an off channel can generate an error comparable to the signal being measured.
Recommended
Automated Test Equipment
The MAX336EPI+ can route test resources among a group of DUT pins in automated test equipment. A single 16:1 structure minimizes the number of external multiplexing components around one measurement amplifier or converter. The 28-pin PDIP package also simplifies through-hole prototyping and bench repair. Precision testing requires accounting for the 400 ohm switch resistance, the low-leakage behavior, and the manufacturer-defined switching and settling limits when calculating stimulus accuracy and measurement time.
Recommended
Analog Signal Routing
The MAX336EPI+ can consolidate 16 low-frequency analog sources into one shared signal path for routing and monitoring. This is useful in laboratory equipment, control panels, and general-purpose analog switching systems where a physical multiplexer saves board space and wiring. Its CMOS implementation, low-leakage characteristics, and 400 ohm on-resistance provide a defined switching baseline, although the final design must satisfy signal-range, bandwidth, injection, and transition requirements in the manufacturer datasheet.
Recommended
Recommended Products Summary
Engineering reference data for MAX336EPI+ — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MAX336EPI | MAX337EPI+ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-PDIP | 28-PDIP | 28-PDIP |
| Multiplexer Configuration | Single 16:1 | Single 16:1 | Dual 8:1 |
| Number of Channels | 16 channels | 16 channels | 16 channels arranged as dual 8:1 |
| Single-Supply Voltage Range | 4.5 V to 30 V | 4.5 V to 30 V | 4.5 V to 30 V |
| Dual-Supply Voltage Range | Plus or minus 4.5 V to plus or minus 20 V | Plus or minus 4.5 V to plus or minus 20 V | Plus or minus 4.5 V to plus or minus 20 V |
| Charge Injection | 3.5 pC typical for MAX336 family | 3.5 pC typical for MAX336 family | 3.5 pC typical for MAX336/MAX337 family |
| ESD Protection | Greater than 2000 V using method 3015.7 | Greater than 2000 V using method 3015.7 | Greater than 2000 V using method 3015.7 |
| Leakage Characteristic | Low leakage | Low leakage | Low leakage |
| Mounting Type | Through-hole | Through-hole | Through-hole |
Key Differentiators
- Single 16:1 organization (vs MAX337EPI+)
- Defined 400 ohm on-resistance (vs MAX337EPI+)
- Wide single-supply operating range (vs MAX336EPI)
Design Notes
Include the 400 ohm on-resistance in the complete source-impedance calculation rather than treating the selected channel as an ideal switch. For a resistive divider or amplifier input, the switch resistance changes the effective transfer ratio; for a capacitive input node, it also changes the available charging current. Add cable and source resistance to establish the worst-case settling time before selecting the acquisition rate.
Do not substitute MAX336, MAX337, and package variants solely because their channel counts look similar. MAX336EPI+ is the single 16:1 configuration in a 28-pin PDIP package, whereas MAX337EPI+ uses the dual 8-channel organization. Confirm address inputs, common terminals, supply connections, package drawing, and signal limits against the manufacturer pin configuration before approving a replacement.
Keep the selected analog route short and place channel-specific filtering or protection close to the associated pins. Provide a low-impedance ground and bypass the supply pins with the capacitance recommended by the manufacturer. For high-impedance sources, use guarding and clean PCB surfaces to minimize leakage from contamination and adjacent traces; the device's low-leakage specification cannot overcome leakage introduced by the board or connectors.
Route multiplexer control signals away from sensitive analog inputs and use a solid ground-plane strategy. Charge injection of 3.5 pC typical can create a transient when the address changes, so acquisition systems should blank or discard samples during transitions. If the multiplexed signal is low frequency and high impedance, include the charge-injection transient in the front-end settling and error analysis.
Compliance Information
The supplied product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The MAX336 is an industrial analog interface IC, so AEC-Q100 qualification is not applicable.