MAX359EPE - Fault-Protected 4:1 Analog Multiplexer | Maxim
MPN: MAX359EPE ✓ ActiveMAX359EPE Overview
An analog multiplexer is an interface IC that routes multiple analog inputs through a shared output path under digital control. A 4:1 multiplexer reduces the number of signal lines required when several sources must be measured sequentially. The MAX359 extends this function with fault-protection circuitry intended to limit damage caused by overvoltage conditions. In the system hierarchy, it belongs to analog switches and multiplexers, interface ICs, and the broader semiconductor category.
The MAX359 family provides two independently selectable 4:1 configurations, giving 8 differential input channels in total. According to the MAX359 manufacturer product page, the MAX359 is the four-channel differential, 2-of-8 multiplexer, while the MAX358 is an eight-channel single-ended 1-of-8 device. Its specified on resistance is 1.8 kOhm. The MAX359EPE is identified as an industrial-temperature component, and the E suffix denotes the manufacturer ordering variant shown in the product records.
The internal series N-channel, P-channel, N-channel arrangement is specifically intended to improve fault protection compared with simpler multiplexer implementations. This architecture matters when analog inputs can temporarily exceed the supply voltages. The active device still has defined supply limits, and the manufacturer should be consulted before applying voltages beyond its absolute maximum ratings or using the multiplexer as a substitute for dedicated protection components.
Typical uses include multichannel instrumentation, sensor acquisition, battery and power-system monitoring, industrial control, and laboratory test equipment. Differential routing is particularly useful for rejecting common-mode disturbance when paired signals share similar noise characteristics. The two 4:1 sections can also support redundant or comparative measurements when the system must route more than one signal group to shared processing circuitry.
For PCB design, place the device so that muxed analog traces remain short and are surrounded by a stable ground reference. Keep external switching or protection components close to exposed connector pins, and route digital select inputs away from sensitive analog inputs to reduce crosstalk. Before power-up, verify every control and signal pin against the manufacturer's operating limits. The family datasheet and pin-description table should define the correct pin assignments and supply requirements.
This page combines the manufacturer function description, package and routing characteristics, practical design guidance, sourcing questions, and qualified drop-in alternatives. It also separates exact ordering variants from package changes, helping engineers identify whether a proposed replacement preserves the original 16-pin PDIP footprint and electrical behavior.
Drop-in alternatives for MAX359EPE — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
MAX359EPE+
✅ Drop-In📋 Reference alternative (not in catalog)
MAX359CPE
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
MAX359EPA
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
MAX359EPE Specifications
| Product Type | Fault-protected analog multiplexer |
| Multiplexer Configuration | Dual 4:1 |
| Differential Channels | 8 channels in two 4-channel differential groups |
| On Resistance | 1.8 kOhm |
| Switch Circuit | 2 circuit IC switch, 4:1 |
| Fault Protection | Enabled |
| Internal Protection Structure | Series N-channel, P-channel, N-channel |
| Package | 16-pin PDIP |
| Package Type | Through-hole PDIP |
| Mounting Type | Through-hole |
| Temperature Grade | Industrial |
| Number of Terminals | 16 |
| Analog Signal Type | Differential |
MAX359EPE through-hole pdip Pin Configuration Guide
Pin configuration for MAX359EPE (through-hole pdip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MAX359EPE.
Refer to the datasheet for full pin configuration.
Typical Applications
MAX359EPE is suitable for 6 applications: Differential Sensor Acquisition, Industrial Process Monitoring, Battery Monitoring Systems, Test and Measurement Systems, Data Acquisition and Instrumentation, Redundant Signal Comparison.
Differential Sensor Acquisition
The MAX359EPE fits multichannel differential sensor acquisition because its two fault-protected 4:1 sections can route eight differential inputs through shared processing channels. The 1.8 kOhm on resistance must be considered alongside the sensor output impedance and amplifier input bias current to avoid measurement gain errors. Pairing related signals on differential paths also helps reject common-mode noise. Before implementation, confirm the switch leakage, off-isolation, switching time, and channel-selection truth table in the MAX359 family datasheet.
Recommended
Industrial Process Monitoring
The MAX359EPE is appropriate for industrial process monitoring when several differential sensor or transducer signals must be sampled by one analog front end. Its dual 4:1 organization reduces analog routing complexity, while fault protection adds resilience when a connected input temporarily moves outside the expected range. Design the enclosure for the E-grade industrial variant, keep traces away from switching nodes, and verify that every external source remains within the absolute maximum ratings. The manufacturer data sheet should govern supply sequencing and control-state behavior.
Recommended
Battery Monitoring Systems
The MAX359EPE can route several differential battery or power-system voltages into a shared monitoring path, simplifying the number of analog input connections required on a controller board. The two differential 4:1 sections support parallel comparison of voltage, current, and temperature channels. Because battery systems can experience large transients, use the device's fault-protection capability as one layer of protection rather than the only protection. Confirm the maximum signal excursion, supply range, and whether an external clamp is required before selecting the multiplexer.
Recommended
Test and Measurement Systems
The MAX359EPE is useful in test and measurement equipment that must connect multiple differential sources to one measurement chain without duplicating front-end circuitry. Its stated 1.8 kOhm on resistance should be included in the input-impedance and settling analysis, particularly for high-accuracy systems. Keep connector traces short and use a stable ground plane to minimize switching transients. Because the exact isolation and bandwidth figures are not stated on the product page, engineers should read the MAX359 family data sheet before setting measurement accuracy limits.
Recommended
Data Acquisition and Instrumentation
The MAX359EPE supports compact data-acquisition systems by consolidating multiple differential inputs into two multiplexed outputs. This allows a shared converter or instrumentation amplifier to process several channels sequentially, provided the multiplexer settling behavior is included in the sampling plan. Route the analog paths away from digital select lines and place optional protection components near connectors. Confirm the exact enable and select logic, supply limits, channel count, and control timing against the manufacturer pin-description table before laying out the PCB.
Recommended
Redundant Signal Comparison
The MAX359EPE can support redundant or comparative signal routing by using its two 4:1 differential sections to select channels for side-by-side measurement. This is useful in condition-monitoring and diagnostic equipment where two related signals must be evaluated through a common analog path. The switch's 1.8 kOhm on resistance and source-to-source variation affect common-mode rejection and channel balance, so characterize the complete measurement path. Also define fail-safe control states so an invalid mux selection cannot expose downstream circuitry to an unintended source.
Recommended
Recommended Products Summary
Engineering reference data for MAX359EPE — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MAX359EPE+ | MAX359CPE | MAX359EPA |
|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Function | Fault-protected dual 4:1 analog multiplexer | Fault-protected dual 4:1 analog multiplexer | Dual 4:1 analog multiplexer | Dual 4:1 analog multiplexer |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Signal Type | Differential | Differential | Differential | Differential |
| Fault Protection | Enabled | Enabled | Enabled | Enabled |
| Number of Terminals | 16 | 16 | 16 | 16 |
Key Differentiators
- Fault-protected analog routing (vs MAX359EPE+)
- Differential channel organization (vs MAX358)
- Through-hole package compatibility (vs MAX359EWE)
- Defined on resistance (vs MAX359CPE)
Design Notes
Route each multiplexed analog node as a short, impedance-controlled trace surrounded by a continuous ground reference. Place the MAX359 close to the connector or sensor interface and preserve symmetry between paired differential inputs. Keep the digital select and enable traces away from the analog paths, and avoid sharing a narrow neck between the multiplexer outputs and downstream amplifiers. These practices reduce capacitive coupling and preserve the differential signal relationship.
Treat the fault-protection structure as limited internal protection rather than an unrestricted surge suppressor. Establish the signal-source maximum, normal supply range, and absolute maximum ratings before connecting external equipment. If an input can exceed those limits or sustain sustained overvoltage, add an appropriate external clamp or series impedance. Also decouple the supplies close to the device and verify power-up and power-down behavior against the MAX359 family datasheet.
Do not treat every MAX359 suffix as a PCB-compatible replacement. MAX359EPE is a 16-pin PDIP, while MAX359EWE is identified as a 16-SOIC and requires a different footprint. Similarly, temperature-grade suffixes must be checked against the system's ambient range. For any proposed substitute, compare the pin-description table, supply limits, on-resistance behavior, fault-protection rating, enable logic, and control truth table before approving the substitution.
Include the 1.8 kOhm on resistance when calculating gain error, input loading, and amplifier headroom. For high-accuracy measurements, also evaluate source impedance, switch leakage, off-isolation, charge injection, and settling time from the family data sheet. Allow sufficient acquisition time after changing a selection state. If the source impedance is high, add a suitable buffer close to the multiplexer so channel resistance does not dominate the measurement node.
Compliance Information
The MAX359 family is an industrial-grade industrial and instrumentation interface component; no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the available product records.