Analog Devices

MAX362ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices

MPN: MAX362ESE+ ✓ Active
Less than 85 ohm Rds(on) 16-pin SOIC Package
MOQ: 1 |

MAX362ESE+ Overview

Analog Devices MAX362ESE+ is a precision, quad, single-pole single-throw analog switch with four normally open channels, a maximum on resistance of 85Ω, and a 16-pin SOIC package. The switch is designed for controlled routing of low-frequency analog signals where consistent channel resistance, low leakage, and a compact surface-mount footprint are important.

An analog switch is an integrated semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw switch provides one signal path that is normally disconnected and closes when its control input is asserted. The quad architecture gives the MAX362ESE+ four independent switch paths, reducing component count in test systems, measurement instruments, signal-conditioning circuits, and controlled analog-routing designs.

The MAX362 family provides on-resistance below 85Ω across the analog signal range. Analog Devices specifies channel matching within 3Ω and a maximum on-resistance change of 9Ω, helping preserve amplitude relationships when signals pass through multiple channels. These characteristics are especially useful when attenuation, calibration, or measurement accuracy depends on similar resistance among switched paths.

The MAX362ESE+ differs from the MAX361 family member through its normally open switch configuration: MAX362 uses normally open channels, while MAX361 uses normally closed channels. Its 1:1 circuit arrangement means the device does not inherently invert the signal. The industrial temperature-grade designation and 16-lead SOIC packaging support conventional surface-mount assembly for industrial and instrumentation applications.

Typical uses include low-frequency sensor multiplexing, sample-and-hold signal routing, automated test equipment, programmable gain networks, and laboratory measurement interfaces. The four channels can route related nodes to a common analog processing chain, although system timing and control logic must ensure that only the intended channel is closed when signal integrity matters.

Layout should keep analog traces short and place bypass and interface components near their associated pins. Control signals should transition cleanly, and unused control or signal pins should be connected according to the manufacturer pin-description table. Because switch resistance can vary with signal amplitude, verify the complete signal path and account for Ron when designing precision dividers, current loops, or low-amplitude sensor interfaces.

This page consolidates the manufacturer switch characteristics, package information, sourcing workflow, verified replacement reference, and practical implementation guidance. It is designed to help engineers evaluate the MAX362ESE+ for new analog-routing designs and assess PCB reuse without relying on generic analog-switch descriptions.

Drop-in alternatives for MAX362ESE+ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MAX362ESE+ (same form factor and footprint) — differing in Mounting Type, Package.

Maxim Integrated
Mounting Type: Surface Mount (SMD/SMT)
Package: 16-SOIC narrow (0.154 inch / 3.90 mm width)
Compare with MAX362ESE+ →

MAX338ESE+

✅ Drop-In
Maxim Integrated
📦 16-pin SOIC
8-Channel / Dual 4-Channel CMOS Analog Multiplexer (Mux or Demux) · 1 · 8:1 · 400 ohm · +4.5V to +30V · +/-4.5V to +/-20V · Bidirectional analog channel · Yes, protected channels

Contact for price

View Datasheet →

MAX362ESE+ Maximum Ratings & Electrical Characteristics

Switch Configuration Quad SPST
Number of Channels 4 circuits
Switch Type Normally open SPST
On-Resistance Less than 85 ohm
Channel Resistance Matching Within 3 ohm
On-Resistance Variation Over Analog Range 9 ohm maximum
Operating Temperature Grade Industrial grade
Package 16-pin SOIC
Mounting Type Surface mount
Package Code SOP

MAX362ESE+ sop Pin Configuration Guide

Pin configuration for MAX362ESE+ (sop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

sop package pinout diagram for MAX362ESE+

No detailed pinout data available for MAX362ESE+.

Refer to the datasheet for full pin configuration.

Typical Applications

MAX362ESE+ is suitable for 6 applications: Low-Frequency Sensor Multiplexing, Automated Test Equipment Signal Routing, Programmable Gain and Attenuation Networks, Precision Measurement Front Ends, Sample-and-Hold Signal Routing, Industrial Control and Signal Conditioning.

🧩

Low-Frequency Sensor Multiplexing

The MAX362ESE+ fits sensor-selection networks requiring four independently controlled, normally open analog paths. With on resistance below 85Ω, channel matching within 3Ω, and a maximum variation of 9Ω across the analog range, it can provide more consistent path resistance than an unspecified discrete switch arrangement. The device is placed between sensor outputs and a shared analog input, while control logic selects the required channel. Because the switches are normally open, disconnected sensors remain isolated until intentionally connected. Designers should verify the numeric leakage and signal-range limits in the Analog Devices data sheet, particularly for high-impedance sources where leakage and off-state coupling can influence accuracy.

🖥️

Automated Test Equipment Signal Routing

The MAX362ESE+ is suitable for automated test equipment that routes several low-frequency nodes to a shared measurement or stimulus path. Four normally open SPST switches reduce the number of discrete routing elements, while resistance matching within 3Ω helps maintain repeatable channel behavior. A practical implementation places the switch close to the instrument backplane and drives its control inputs from test-sequence logic. The 16-pin SOIC package also simplifies board-level integration. Engineers should account for the maximum 85Ω on resistance when calculating divider ratios and should validate switching transients, leakage, and logic thresholds for the selected supply arrangement.

📡

Programmable Gain and Attenuation Networks

The MAX362ESE+ can route resistance networks into and out of a signal path to create programmable gain or attenuation settings. Its sub-85Ω on resistance and channel-to-channel matching within 3Ω make switch resistance a manageable part of network design when the switched impedance is appropriately chosen. The four normally open switches can select one branch at a time and prevent unintended parallel paths during state changes. In a practical circuit, the device is placed adjacent to the precision resistor network so that switch resistance does not add substantial parasitic capacitance or long trace resistance. Final tolerance calculations should include the maximum 85Ω resistance, the 9Ω variation over signal amplitude, and the resistor network's own tolerance.

🔧

Precision Measurement Front Ends

The MAX362ESE+ is useful in measurement front ends that need to select among several analog inputs before amplification or conversion. The matched channel resistance helps preserve consistent gain and offset behavior across measurements, while the normally open configuration reduces unintended coupling between inactive inputs. Place the switch close to the measurement node and use a high-impedance amplifier when source impedance is high. According to the Analog Devices MAX361/MAX362 data sheet Rev. 2, the device provides low leakage and low on resistance. The exact leakage limit, input swing, and switching characteristics should be checked against the intended signal range and measurement bandwidth before production release.

📺

Sample-and-Hold Signal Routing

The MAX362ESE+ can route one of four signal sources into a sample-and-hold stage while providing a compact alternative to multiple discrete SPST devices. Its maximum on resistance below 85Ω should be included when selecting the acquisition capacitance and settling time, and the 3Ω channel-matching specification helps make channel-dependent errors more predictable. The normally open configuration is helpful when the held node must not be connected to a source during control transitions. Use short analog traces, place the hold capacitor near the receiving amplifier, and verify charge injection, off isolation, and switching time from the manufacturer data sheet for the intended bandwidth and signal amplitude.

🏭

Industrial Control and Signal Conditioning

The industrial-grade MAX362ESE+ fits control boards that route conditioned analog signals among sensors, filter stages, or actuator drivers. Its four normally open channels allow a controller to select a source without maintaining unintended parallel signal paths, while the 16-pin SOIC package supports conventional surface-mount assembly. The sub-85Ω on resistance limits added path resistance, and matching within 3Ω supports repeatable behavior across channels. PCB implementation should keep sensitive traces away from control and power routing, provide a stable reference and supply arrangement, and account for leakage in high-impedance sensor circuits. Validate the logic thresholds, supply range, and operating temperature limits in the manufacturer documentation.

What is the MAX362ESE+?
The MAX362ESE+ is a precision, quad, normally open SPST analog switch from Analog Devices, packaged in a 16-pin SOIC. According to the manufacturer data sheet Rev. 2, its four channels have on resistance below 85Ω, match one another within 3Ω, and vary by no more than 9Ω across the analog signal range. It is intended for controlled routing of low-frequency analog signals in compact surface-mount equipment.
What is the on-resistance of MAX362ESE+?
The MAX362ESE+ has a maximum on resistance below 85Ω, with channel resistance matching specified within 3Ω. Analog Devices also specifies a maximum on-resistance change of 9Ω over the analog signal range. According to the manufacturer data sheet Rev. 2, these figures make the device useful in measurement and signal-conditioning paths where similar resistance among channels helps preserve signal relationships.
Where can I download the MAX362ESE+ datasheet PDF?
The MAX362ESE+ datasheet is available through the official Analog Devices MAX362 product page at https://www.analog.com/en/products/max362.html. That page links to the MAX361/MAX362 data sheet Rev. 2 and its product documentation. Use the manufacturer pin-description table and electrical-characteristics tables when assigning PCB tracks, selecting control levels, and verifying switch resistance and leakage requirements.
Where can I find the MAX362ESE+ pinout?
The MAX362ESE+ pinout is documented in the pin-description section of the Analog Devices MAX361/MAX362 data sheet Rev. 2. The device uses a 16-pin SOIC package, but pin numbering must be checked against the manufacturer table before layout because the four normally open channels and their control inputs are not identified in the product-page summary. The official page is https://www.analog.com/en/products/max362.html.
What is the difference between MAX362 and MAX361?
The principal functional difference is the switch state: MAX362 has four normally open switches, while MAX361 has four normally closed switches. Both are precision quad SPST devices with on resistance below 85Ω, channel matching within 3Ω, and on-resistance variation of 9Ω maximum. According to Analog Devices, MAX362ESE+ is therefore appropriate when a path should remain disconnected until control is asserted.
Can MAX338ESE+ replace MAX362ESE+?
MAX338ESE+ is identified by a component-comparison source as a complete replacement with consistent terminals and package characteristics. The source also describes the replacement as requiring no modification to an existing circuit. Before approving it for production, verify the actual pin functions, supply arrangement, logic levels, on resistance, leakage, and switching timing against the MAX362ESE+ manufacturer data sheet and your operating conditions.
What is the best drop-in replacement for MAX362ESE+?
MAX338ESE+ is the closest verified drop-in candidate because the comparison source states that its terminals and package are consistent with MAX362ESE+ and that no circuit modification is required. The same source also reports consistent main performance parameters and functional characteristics. Final qualification should nevertheless confirm pinout, control polarity, supply voltage, leakage, and analog signal range in the manufacturer documentation.
Is MAX362ESE+ suitable for sensor multiplexing?
The MAX362ESE+ is suitable for many low-frequency sensor multiplexing tasks because it provides four normally open SPST paths and on resistance below 85Ω. Its channel matching within 3Ω can help maintain consistent path resistance across selected sensors. The design should still account for leakage, switching transients, source impedance, and the maximum signal amplitude permitted by the manufacturer data sheet.
MAX362ESE+ vs MAX338ESE+ — which is better for a precision test system?
Choose MAX362ESE+ when its explicitly specified behavior—four normally open paths, on resistance below 85Ω, matching within 3Ω, and 9Ω maximum variation—is the controlling requirement. MAX338ESE+ is attractive when PCB reuse and confirmed terminal and package consistency are the priorities. The final selection should follow a side-by-side review of logic polarity, leakage, switching time, and power requirements.
When should I choose MAX362ESE+ instead of MAX338ESE+?
Choose MAX362ESE+ when normally open behavior and the documented 85Ω maximum channel resistance are central to the design. The manufacturer specification for MAX362 also provides explicit channel-matching and signal-range variation limits, which can simplify design verification. Select MAX338ESE+ instead when its replacement cross-reference and package compatibility are more important than using the MAX362-specific characterization.
How does the normally open configuration affect MAX362ESE+ designs?
A normally open MAX362 channel remains disconnected until its control signal activates the switch, preventing unintended signal paths during reset or control initialization. This behavior is useful when multiple sources share a downstream node and only one should be connected at a time. Designers should account for control timing and switch transients so that the inactive state does not create an unintended measurement disturbance.
What is the leakage current of MAX362ESE+?
The manufacturer characterizes the MAX362 as a low-leakage precision switch, but the product-page summary does not state the numeric maximum. Use the leakage-current specification in the Analog Devices MAX361/MAX362 data sheet Rev. 2 for design calculations. Leakage is particularly important when the switched node sources a high-impedance signal or when off-state isolation contributes directly to measurement error.
Is MAX362ESE+ in stock?
Current stock status can change rapidly, so use the Request a Quote form on this page to request the current availability for MAX362ESE+ and confirm the required quantity and delivery schedule. The part is listed as a production device by Analog Devices, and its industrial-grade 16-pin SOIC construction supports standard surface-mount sourcing. The form is the appropriate route for current stock, lot, and lead-time confirmation.
What is the price of MAX362ESE+?
Use the Request a Quote form on this page for the current MAX362ESE+ unit price, volume pricing, stock, and lead time. Quote pricing can reflect quantity, packaging, component condition, and market availability, so a static price figure may not represent the purchasing configuration for your project. Submit the exact MPN, quantity, and required delivery information for a current quotation.
How long is the lead time for MAX362ESE+?
The current lead time for MAX362ESE+ should be confirmed through the Request a Quote form on this page by stating the required quantity, date code, and target delivery schedule. Lead time can change with inventory, production planning, and packaging requirements. The manufacturer identifies MAX362 as a production device, but current operational availability remains a commercial question for each order.
What are the key specifications of MAX362ESE+ that engineers should know?
The key MAX362ESE+ specifications are four normally open SPST channels, on resistance below 85Ω, channel matching within 3Ω, and no more than 9Ω on-resistance variation over the analog range. The device is offered in a 16-pin SOIC package and carries an industrial temperature-grade designation. Analog Devices specifies low leakage, but its numeric limit must be taken from the manufacturer data sheet Rev. 2.

Engineering reference data for MAX362ESE+ — comparison, design guidance, and compliance information.

Selection Guide

Choose MAX362ESE+ when the design requires four normally open precision SPST paths and when the documented electrical limits provide a clear basis for signal-path calculations. Its on resistance below 85Ω, matching within 3Ω, and 9Ω maximum variation are particularly useful in matched measurement channels, programmable networks, and low-frequency multiplexing systems. MAX338ESE+ is the practical PCB-reuse candidate identified by the cross-reference source, which states that terminals and packages are consistent and modification is unnecessary. Select it when footprint continuity is the dominant requirement, but verify its switch-state behavior, pin functions, leakage, logic levels, and timing before production. Use MAX361 instead only when normally closed channels are specifically required; it is functionally different from the normally open MAX362 and should not be treated as an automatic substitution.

Comparison with Alternatives

Parameter This Product MAX338ESE+
Package 16-pin SOIC 16-pin SOIC - same package stated by comparison source
Brand Analog Devices Maxim Integrated
Mounting Type Surface mount Surface mount

Key Differentiators

  • Explicitly characterized precision resistance (vs MAX338ESE+)
  • Normally open four-channel routing (vs MAX338ESE+)
  • Industrial surface-mount implementation (vs MAX338ESE+)

Design Notes

Treat the MAX362ESE+ on resistance as part of the signal path rather than as an ideal switch. The manufacturer specifies less than 85Ω on resistance, matching within 3Ω, and a 9Ω maximum variation over the analog range. Include these values in divider, gain, settling-time, and source-loading calculations. For high-impedance sensors, also evaluate leakage and off-state coupling using the numeric limits in the manufacturer data sheet.

Place the MAX362ESE+ close to the multiplexed analog node and its receiving amplifier to minimize trace resistance and parasitic capacitance. Keep switched and un-switched high-impedance nodes short, provide a quiet ground reference, and route control traces away from sensitive analog tracks. Use the pin-description table in the Analog Devices data sheet Rev. 2 to confirm control inputs, common terminals, and normally open terminals before releasing the layout.

Do not substitute a normally closed switch family when the control default must leave the signal path disconnected. MAX362ESE+ provides four normally open channels, while MAX361 provides normally closed channels. Likewise, do not approve MAX338ESE+ solely from its package description: verify pin functions, control polarity, logic thresholds, leakage, switching time, and supply requirements. A footprint match alone does not guarantee equivalent system behavior.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The MAX362ESE+ is identified as an industrial-grade analog switch, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated in the accessible product information. AEC-Q100 qualification is not indicated for this industrial analog switch.

Related Searches

MAX362ESE+ datasheet MAX362ESE+ pinout MAX362ESE+ datasheet pdf MAX362ESE+ specifications MAX362ESE+ equivalent MAX362ESE+ replacement MAX362ESE+ cross reference MAX362ESE+ vs MAX338ESE+ MAX362 16-SOIC analog switch MAX362ESE+ sensor multiplexing MAX362ESE+ price MAX362ESE+ stock Analog Devices MAX362ESE+

Related Components & Terms

Analog Devices Maxim Integrated MAX362ESE+ MAX338ESE+ MAX361 MAX362 analog switch SPST switch normally open switch interface IC semiconductor on resistance channel matching leakage current signal routing sensor multiplexing 16-pin SOIC SOIC package family surface mount SMD industrial grade Analog Devices MAX361/MAX362 data sheet Rev. 2 1:1 circuit arrangement programmable gain network
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details