MAX362ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices
料号: MAX362ESE+ ✓ 量产中MAX362ESE+ 概述
An analog switch is an integrated semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw switch provides one signal path that is normally disconnected and closes when its control input is asserted. The quad architecture gives the MAX362ESE+ four independent switch paths, reducing component count in test systems, measurement instruments, signal-conditioning circuits, and controlled analog-routing designs.
The MAX362 family provides on-resistance below 85Ω across the analog signal range. Analog Devices specifies channel matching within 3Ω and a maximum on-resistance change of 9Ω, helping preserve amplitude relationships when signals pass through multiple channels. These characteristics are especially useful when attenuation, calibration, or measurement accuracy depends on similar resistance among switched paths.
The MAX362ESE+ differs from the MAX361 family member through its normally open switch configuration: MAX362 uses normally open channels, while MAX361 uses normally closed channels. Its 1:1 circuit arrangement means the device does not inherently invert the signal. The industrial temperature-grade designation and 16-lead SOIC packaging support conventional surface-mount assembly for industrial and instrumentation applications.
Typical uses include low-frequency sensor multiplexing, sample-and-hold signal routing, automated test equipment, programmable gain networks, and laboratory measurement interfaces. The four channels can route related nodes to a common analog processing chain, although system timing and control logic must ensure that only the intended channel is closed when signal integrity matters.
Layout should keep analog traces short and place bypass and interface components near their associated pins. Control signals should transition cleanly, and unused control or signal pins should be connected according to the manufacturer pin-description table. Because switch resistance can vary with signal amplitude, verify the complete signal path and account for Ron when designing precision dividers, current loops, or low-amplitude sensor interfaces.
This page consolidates the manufacturer switch characteristics, package information, sourcing workflow, verified replacement reference, and practical implementation guidance. It is designed to help engineers evaluate the MAX362ESE+ for new analog-routing designs and assess PCB reuse without relying on generic analog-switch descriptions.
直接替换替代料: MAX362ESE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX362ESE+ (相同外形与封装尺寸) ——差异在于 Mounting Type, Package.
MAX338ESE+
✅ 直接替换联系询价
查看数据手册 →MAX362ESE+ 最大额定值与电气特性
| Switch Configuration | Quad SPST |
| Number of Channels | 4 circuits |
| Switch Type | Normally open SPST |
| On-Resistance | Less than 85 ohm |
| Channel Resistance Matching | Within 3 ohm |
| On-Resistance Variation Over Analog Range | 9 ohm maximum |
| Operating Temperature Grade | Industrial grade |
| 封装 | 16-pin SOIC |
| 安装类型 | Surface mount |
| Package Code | SOP |
MAX362ESE+ sop 引脚配置指南
MAX362ESE+(sop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX362ESE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX362ESE+ 适用于 6 应用s: Low-Frequency Sensor Multiplexing, Automated Test Equipment Signal Routing, Programmable Gain and Attenuation Networks, Precision Measurement Front Ends, Sample-and-Hold Signal Routing, Industrial Control and Signal Conditioning.
Low-Frequency Sensor Multiplexing
The MAX362ESE+ fits sensor-selection networks requiring four independently controlled, normally open analog paths. With on resistance below 85Ω, channel matching within 3Ω, and a maximum variation of 9Ω across the analog range, it can provide more consistent path resistance than an unspecified discrete switch arrangement. The device is placed between sensor outputs and a shared analog input, while control logic selects the required channel. Because the switches are normally open, disconnected sensors remain isolated until intentionally connected. Designers should verify the numeric leakage and signal-range limits in the Analog Devices data sheet, particularly for high-impedance sources where leakage and off-state coupling can influence accuracy.
推荐
Automated Test Equipment Signal Routing
The MAX362ESE+ is suitable for automated test equipment that routes several low-frequency nodes to a shared measurement or stimulus path. Four normally open SPST switches reduce the number of discrete routing elements, while resistance matching within 3Ω helps maintain repeatable channel behavior. A practical implementation places the switch close to the instrument backplane and drives its control inputs from test-sequence logic. The 16-pin SOIC package also simplifies board-level integration. Engineers should account for the maximum 85Ω on resistance when calculating divider ratios and should validate switching transients, leakage, and logic thresholds for the selected supply arrangement.
推荐
Programmable Gain and Attenuation Networks
The MAX362ESE+ can route resistance networks into and out of a signal path to create programmable gain or attenuation settings. Its sub-85Ω on resistance and channel-to-channel matching within 3Ω make switch resistance a manageable part of network design when the switched impedance is appropriately chosen. The four normally open switches can select one branch at a time and prevent unintended parallel paths during state changes. In a practical circuit, the device is placed adjacent to the precision resistor network so that switch resistance does not add substantial parasitic capacitance or long trace resistance. Final tolerance calculations should include the maximum 85Ω resistance, the 9Ω variation over signal amplitude, and the resistor network's own tolerance.
推荐
Precision Measurement Front Ends
The MAX362ESE+ is useful in measurement front ends that need to select among several analog inputs before amplification or conversion. The matched channel resistance helps preserve consistent gain and offset behavior across measurements, while the normally open configuration reduces unintended coupling between inactive inputs. Place the switch close to the measurement node and use a high-impedance amplifier when source impedance is high. According to the Analog Devices MAX361/MAX362 data sheet Rev. 2, the device provides low leakage and low on resistance. The exact leakage limit, input swing, and switching characteristics should be checked against the intended signal range and measurement bandwidth before production release.
推荐
Sample-and-Hold Signal Routing
The MAX362ESE+ can route one of four signal sources into a sample-and-hold stage while providing a compact alternative to multiple discrete SPST devices. Its maximum on resistance below 85Ω should be included when selecting the acquisition capacitance and settling time, and the 3Ω channel-matching specification helps make channel-dependent errors more predictable. The normally open configuration is helpful when the held node must not be connected to a source during control transitions. Use short analog traces, place the hold capacitor near the receiving amplifier, and verify charge injection, off isolation, and switching time from the manufacturer data sheet for the intended bandwidth and signal amplitude.
推荐
Industrial Control and Signal Conditioning
The industrial-grade MAX362ESE+ fits control boards that route conditioned analog signals among sensors, filter stages, or actuator drivers. Its four normally open channels allow a controller to select a source without maintaining unintended parallel signal paths, while the 16-pin SOIC package supports conventional surface-mount assembly. The sub-85Ω on resistance limits added path resistance, and matching within 3Ω supports repeatable behavior across channels. PCB implementation should keep sensitive traces away from control and power routing, provide a stable reference and supply arrangement, and account for leakage in high-impedance sensor circuits. Validate the logic thresholds, supply range, and operating temperature limits in the manufacturer documentation.
推荐
推荐产品汇总
工程参考数据: MAX362ESE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX338ESE+ |
|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC - same package stated by comparison source |
| Brand | Analog Devices | Maxim Integrated |
| Mounting Type | Surface mount | Surface mount |
关键差异点
- Explicitly characterized precision resistance (对比 MAX338ESE+)
- Normally open four-channel routing (对比 MAX338ESE+)
- Industrial surface-mount implementation (对比 MAX338ESE+)
设计说明
Treat the MAX362ESE+ on resistance as part of the signal path rather than as an ideal switch. The manufacturer specifies less than 85Ω on resistance, matching within 3Ω, and a 9Ω maximum variation over the analog range. Include these values in divider, gain, settling-time, and source-loading calculations. For high-impedance sensors, also evaluate leakage and off-state coupling using the numeric limits in the manufacturer data sheet.
Place the MAX362ESE+ close to the multiplexed analog node and its receiving amplifier to minimize trace resistance and parasitic capacitance. Keep switched and un-switched high-impedance nodes short, provide a quiet ground reference, and route control traces away from sensitive analog tracks. Use the pin-description table in the Analog Devices data sheet Rev. 2 to confirm control inputs, common terminals, and normally open terminals before releasing the layout.
Do not substitute a normally closed switch family when the control default must leave the signal path disconnected. MAX362ESE+ provides four normally open channels, while MAX361 provides normally closed channels. Likewise, do not approve MAX338ESE+ solely from its package description: verify pin functions, control polarity, logic thresholds, leakage, switching time, and supply requirements. A footprint match alone does not guarantee equivalent system behavior.
合规信息
The MAX362ESE+ is identified as an industrial-grade analog switch, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated in the accessible product information. AEC-Q100 qualification is not indicated for this industrial analog switch.