Analog Devices

MAX388EPN+ - 8:1 3kOhm Analog Multiplexer | Analog Devices

MPN: MAX388EPN+ ✗ End of Life
3 kOhm Rds(on) 18-pin PDIP Package
MOQ: 1 |

MAX388EPN+ Overview

The Analog Devices MAX388EPN+ is a fault-protected, 8-channel single-ended analog multiplexer with an 8:1 configuration, 3 kOhm on-resistance and an 18-pin PDIP package. The device uses internal data latches to hold the selected channel, allowing control signals to change the active input without disrupting the selected analog path. Its high-voltage, N-channel, P-channel, N-channel switch architecture improves fault protection when voltage remains present after the device power is removed.

An analog multiplexer is an interface IC that routes one of several analog inputs to a shared output. The MAX388 family combines an 8:1 single-ended multiplexer with internal selection latches, placing it in the interface IC hierarchy alongside analog switches, mux/demux devices and signal-routing components. This makes the device useful when several sensor, measurement, or control signals must share a limited number of converter inputs.

Key features include an 8:1 multiplexing ratio, 3 kOhm on-resistance and a high-voltage fault-protected architecture. The internal latches remove the need to hold a control input in a defined state after selection. The product family also provides an off behavior when power is removed but input voltages remain applied, allowing all channels to turn off and limiting unintended signal paths. The MAX388EPN+ is specifically listed in an 18-pin PDIP package.

The MAX388 family uses a high-voltage series N-channel, P-channel, N-channel structure rather than a conventional single-polarity switch arrangement. This topology is specifically intended to improve fault protection in systems where external inputs can exceed the supply voltage or where power can be removed before the analog signals. The 3 kOhm on-resistance is appropriate for medium-impedance sensor and instrumentation paths, although system gain, leakage and settling requirements must be evaluated in the complete signal chain.

Typical uses include multi-sensor signal selection, instrumentation measurement multiplexing, industrial control signal routing, test-equipment input selection and embedded analog measurement systems. The latched channel selection is especially useful when a host controller writes a channel address and then performs an analog conversion. In these systems, the mux reduces the number of analog input channels required at the converter while preserving a defined route through the selected switch.

Designers should confirm the absolute maximum input and supply ratings, channel leakage, off isolation, on-state resistance tolerance and acquisition settling time in the manufacturer datasheet before finalizing signal paths. Input and ground connections should be arranged to minimize coupling between adjacent channels, and unused digital control inputs should be driven to valid logic levels. Because the MAX388 family is obsolete, long-life programs should verify availability, alternate sourcing and any required qualification before release to production.

This product page consolidates the confirmed switch ratio, on-resistance, package, fault-protection architecture and lifecycle information with practical design guidance. It also identifies the limited number of verified drop-in alternatives, helping engineers distinguish a true pin-compatible replacement from a broader functional equivalent before modifying an existing 18-pin PCB layout.

Drop-in alternatives for MAX388EPN+ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

MAX388CPN+

✅ Drop-In
📦 18-pin PDIP
Same 18-pin PDIP package and documented complete replacement; key performance and functional characteristics are consistent, with no stated numerical offset.

📋 Reference alternative (not in catalog)

MAX388EPN

✅ Drop-In
📦 18-pin PDIP
Same MAX388 family, 8:1 function and 18-pin PDIP package; ordering-code qualification differs, with no confirmed numerical performance difference stated.

📋 Reference alternative (not in catalog)

MAX388EPN+ Specifications

Product Type 8-channel single-ended analog multiplexer
Multiplexer Configuration 8:1
Number of Circuits 1 circuit
On-Resistance 3 kOhm
Package 18-pin PDIP
Switch Architecture High-voltage series N-channel, P-channel, N-channel
Selection Control Internal data latches
Fault Protection High-voltage fault-protected channels
Power-Off Behavior All channels turn off when input voltages remain applied
Product Lifecycle Obsolete
Mounting Type Through-hole
Channel Count 8 channels
Single-Ended Multiplexing Supported

MAX388EPN+ 18-pin pdip Pin Configuration Guide

Pin configuration for MAX388EPN+ (18-pin pdip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

18-pin pdip package pinout diagram for MAX388EPN+

No detailed pinout data available for MAX388EPN+.

Refer to the datasheet for full pin configuration.

Typical Applications

MAX388EPN+ is suitable for 6 applications: Multi-Sensor Measurement, Industrial Control Signal Routing, Test and Measurement Systems, Instrumentation Signal Conditioning, Embedded Analog Monitoring, Diagnostic Signal Selection.

🏭

Multi-Sensor Measurement

The MAX388EPN+ fits a multi-sensor measurement front end by selecting one of eight single-ended inputs and presenting it to a shared analog measurement channel. Its 8:1 organization reduces the number of converter inputs needed when monitoring temperature, pressure, position or level transducers. The 3 kOhm on-resistance is suitable for many medium-impedance sensor paths, while the internal latches let a controller issue an address and retain the selected route during conversion. Designers should verify leakage and settling requirements for the highest-impedance sensor and maintain the device within its specified supply and input limits.

🏭

Industrial Control Signal Routing

The MAX388EPN+ can route multiple control or feedback signals through one shared analog input in an industrial controller. Eight latched single-ended channels provide deterministic address selection, and the 3 kOhm on-resistance is appropriate for many low-frequency control paths. The high-voltage fault-protected architecture is particularly relevant when an external signal source may remain energized while the controller supply is removed. Engineers should confirm the absolute maximum input voltage, off-state behavior and grounding arrangement for each analog source, and use the manufacturer pin table to implement address and latch controls correctly.

🔧

Test and Measurement Systems

A MAX388EPN+ can provide input selection in test and measurement equipment that must connect several analog sources to one measurement chain. Eight single-ended inputs, a 3 kOhm on-resistance and latched control support repeatable source routing under software control. This arrangement helps limit converter count while preserving a defined path for calibration, diagnostic and DUT signals. Because the MAX388 family is obsolete, instrument designers should confirm channel leakage, isolation, settling time and switching transients against their accuracy budget, then plan the MAX388CPN+ as a potential same-package migration path.

📟

Instrumentation Signal Conditioning

The MAX388EPN+ is applicable between multiple instrumentation outputs and a shared analog-processing front end. Its eight single-ended channels allow a system to select thermocouple, bridge, potentiometer or other slow-moving analog signals without providing a dedicated converter input for every channel. The latched selection reduces control complexity, and 3 kOhm on-resistance can support common medium-impedance sensor networks. Signal integrity depends on keeping input traces short, providing a stable reference and observing the multiplexer leakage and acquisition settling requirements in the manufacturer datasheet, particularly when source impedance is high.

🧩

Embedded Analog Monitoring

The MAX388EPN+ can reduce analog input count in an embedded monitoring system by selecting one of eight external conditions for a common ADC channel. Its internal data latches support a simple address-and-latch control sequence, while the 3 kOhm on-resistance accommodates many sensor and divider networks. The device is especially relevant to legacy systems designed around the MAX388 family, but engineers should not introduce it into a new design without considering the obsolete lifecycle and a verified migration path. Check the complete datasheet for input thresholds, timing and fault conditions before final firmware and board decisions.

🖥️

Diagnostic Signal Selection

The MAX388EPN+ supports diagnostic systems that must compare or monitor several analog fault or status signals through one shared acquisition path. Eight latched channels can be scanned under controller supervision, and the fault-protected high-voltage architecture is advantageous when a monitored signal can outlive the logic supply. The 3 kOhm on-resistance supports many conventional monitoring circuits, but engineers must validate off-state behavior, leakage and absolute maximum inputs for the specific fault environment. The complete pin and electrical tables should accompany any redesign because legacy package variants can differ in control implementation.

Recommended Products Summary

MAX388EPN+ Analog Devices Used in: Multi-Sensor Measurement, Industrial Control Signal Routing, Test and Measurement Systems, Instrumentation Signal Conditioning, Embedded Analog Monitoring, Diagnostic Signal Selection MAX388CPN+ Pin-compatible MAX388 family selector Used in: Multi-Sensor Measurement, Industrial Control Signal Routing, Test and Measurement Systems, Embedded Analog Monitoring MAX388EPN Same-family 18-pin DIP ordering option Used in: Instrumentation Signal Conditioning, Diagnostic Signal Selection
Where can I download the MAX388EPN+ datasheet PDF?
The MAX388EPN+ datasheet can be obtained through the Analog Devices MAX388 product page. The manufacturer describes the device as an obsolete 8-channel, single-ended 1-of-8 multiplexer with internal data latches and a high-voltage series N-channel, P-channel, N-channel protection structure. Use the datasheet's pin description, electrical characteristics and application information to confirm control logic, absolute maximum ratings and board-level implementation before substitution or redesign.
What is the MAX388EPN+?
The MAX388EPN+ is an 8-channel single-ended analog multiplexer packaged in an 18-pin PDIP. It routes one of eight inputs through an 8:1 switching arrangement with 3 kOhm on-resistance and uses internal data latches for channel selection. Analog Devices describes the high-voltage fault-protected architecture as improving behavior when external input voltages remain applied after device power is removed.
Where can I find the MAX388EPN+ pinout?
The MAX388EPN+ pinout is documented in the MAX388 manufacturer datasheet and corresponds to the 18-pin PDIP package listed for the device. The package diagram and pin-description table should be used to assign the eight analog inputs, the multiplexer output, address and latch controls, supply connections and ground. Confirm every net against the exact datasheet revision when planning a replacement because the sibling MAX388 variants share a package but do not necessarily use every control identically.
Is MAX388EPN+ suitable for multiplexing sensor signals?
The MAX388EPN+ can suit medium-impedance sensor signals because it combines eight single-ended inputs with 3 kOhm on-resistance and latched channel selection. A controller can load an address, let the selected path settle, and then perform an analog measurement. Leakage, off isolation, settling time and input overvoltage must remain within the datasheet limits, especially for high-impedance sources where leakage can create measurement error.
What can replace the obsolete MAX388EPN+?
The verified pin-compatible replacement for the MAX388EPN+ is the MAX388CPN+, which uses the same 18-pin PDIP format and is described as a complete replacement with consistent terminals and package characteristics. Confirm the control truth table, electrical limits and selected-channel behavior in the manufacturer documentation before substitution. The MAX388 family is obsolete, so production programs should also plan for lifecycle and sourcing risk.
Is MAX388CPN+ a drop-in replacement for MAX388EPN+?
The MAX388CPN+ is a drop-in candidate for the MAX388EPN+ because the MAX388CPN and MAX388EPN comparison identifies consistent terminals and an 18-pin DIP package. The device family uses the same latched multiplexer concept, but engineers should verify the exact pin functions, enable polarity, address decoding and absolute maximum ratings before releasing the substitution to production.
MAX388EPN+ vs MAX388CPN+ — which is better for an existing 18-pin design?
The MAX388CPN+ is the stronger choice for an existing MAX388EPN+ footprint when its complete pin and control compatibility has been verified. The MAX388EPN+ has 3 kOhm on-resistance, eight single-ended channels and a high-voltage N-channel, P-channel, N-channel protection structure. The MAX388CPN+ is identified as a complete replacement with consistent terminals and package, making it suitable for a no-PCB-change migration.
When should I choose MAX388EPN+ instead of MAX388CPN+?
Choose the MAX388EPN+ only when an original design specifically requires that ordering code or its documented electrical and control characteristics. For a new production design, the MAX388CPN+ should be evaluated first because it is identified as a complete 18-pin replacement. The comparison must still include fault behavior, control truth table, maximum ratings and supply sequencing; package identity alone does not establish full functional equivalence.
How does the MAX388EPN+ protect channels when power is removed?
The MAX388EPN+ uses a high-voltage series N-channel, P-channel, N-channel switch structure to improve fault protection. According to Analog Devices, removing power while input voltages remain applied causes all channels to turn off, allowing only the intended fault current path described by the device architecture. This behavior is useful when an external source can remain active after the logic supply collapses.
Is the MAX388EPN+ currently active?
The MAX388EPN+ is obsolete, as explicitly stated on the Analog Devices MAX388 product page. A replacement or redesign should therefore address both technical compatibility and continuing availability. The MAX388CPN+ is a verified same-package candidate, while long-lived equipment programs should assess whether their fault-protection and precision requirements justify continued use of this legacy multiplexer family.
What are the key specifications of MAX388EPN+ that engineers should know?
The principal MAX388EPN+ specifications are an 8:1 configuration, eight single-ended channels, one multiplexed circuit, 3 kOhm on-resistance, internal selection latches and an 18-pin PDIP package. The device also uses a high-voltage series N-channel, P-channel, N-channel architecture for improved fault protection. Supply voltage, temperature range, leakage, isolation and switching time should be taken from the manufacturer datasheet for design qualification.
Where can I buy MAX388EPN+ online?
Use the Request a Quote form on this page to request current MAX388EPN+ availability, minimum order quantity and delivery information. The part is obsolete, so stock and sourcing conditions can change quickly. Provide the exact MAX388EPN+ ordering code, required quantity and acceptable delivery date when requesting the quotation.
What is the price of MAX388EPN+?
Current MAX388EPN+ commercial terms are handled through the Request a Quote form on this page. Because the MAX388 family is obsolete, quantity, condition and sourcing route can materially affect availability. Submit the required quantity, delivery location and target date so the quote can reflect the exact ordering code and current supply conditions.
What is the lead time for MAX388EPN+?
The current lead time for MAX388EPN+ should be requested through the Request a Quote form on this page. As an obsolete member of the MAX388 family, the component may depend on remaining factory inventory or authorized channel stock rather than a standard active-production schedule. Include the annual usage, required package quantity and latest acceptable arrival date when requesting supply information.
Is MAX388EPN+ in stock?
MAX388EPN+ availability should be confirmed through the Request a Quote form on this page. The manufacturer classifies the MAX388 product as obsolete, so current stock may be limited and can change without notice. A quote request should state the quantity required and whether reel, tube, tray or another permitted delivery format is needed for the production plan.
What is the best Analog Devices equivalent for MAX388EPN+?
The MAX388CPN+ is the best verified Analog Devices equivalent for the MAX388EPN+ because it is identified as a complete replacement with consistent terminals and an 18-pin DIP package. This allows a potential drop-in transition without changing the board outline. Final approval should compare the pin functions, control truth table, electrical limits and fault-protection behavior against the manufacturer datasheets.

Engineering reference data for MAX388EPN+ — comparison, design guidance, and compliance information.

Selection Guide

Choose the MAX388EPN+ when maintaining an existing 18-pin PDIP design that specifically calls out that ordering code, especially where external inputs may remain energized after the logic supply is removed. Its confirmed 8:1 configuration, 3 kOhm on-resistance and latched channel selection suit legacy measurement and signal-routing systems. For a new migration, evaluate MAX388CPN+ first because it is identified as a complete replacement with consistent terminals and package. Confirm the control truth table, enable behavior, maximum ratings and electrical characteristics before substitution. The non-plus MAX388EPN can also be evaluated for same-family legacy procurement, but its ordering-code and qualification requirements should be reviewed. Because the family is obsolete, engineers must balance drop-in convenience against long-term availability and consider a modern multiplexer redesign when the board can change.

Comparison with Alternatives

Parameter This Product MAX388CPN+ MAX388EPN
Brand Analog Devices Analog Devices Analog Devices
Package 18-pin PDIP 18-pin PDIP 18-pin PDIP
Multiplexer Configuration 8:1 8:1 8:1
Channel Count 8 single-ended channels 8 single-ended channels 8 single-ended channels
On-Resistance 3 kOhm 3 kOhm 3 kOhm
Number of Circuits 1 circuit 1 circuit 1 circuit
Selection Control Internal data latches Internal data latches Internal data latches
Fault Protection High-voltage fault-protected architecture Fault-protected MAX388 family operation High-voltage fault-protected architecture
Mounting Type Through-hole Through-hole Through-hole

Key Differentiators

  • Confirmed complete same-package replacement path (vs MAX388CPN+)
  • Exact MAX388EPN+ ordering-code availability for legacy repair (vs MAX388EPN)
  • Fault-protected power-off channel behavior (vs MAX388CPN+)

Design Notes

Treat the power-off fault behavior as a system-level constraint, not merely a switching convenience. The MAX388 family is designed to turn all channels off when power is removed while input voltages remain present, but external clamp networks, source impedance and downstream protection still determine the actual fault energy. Review the absolute maximum input ratings, supply sequence and system power-down states in the manufacturer datasheet before connecting field-wired or externally powered signals.

Route the eight analog inputs as short, quiet traces and connect the multiplexer ground pins directly to the measurement-system ground plane. Place the device near the shared analog output to limit trace resistance, capacitance and susceptibility to adjacent digital switching. Keep address and latch routing away from sensitive input nets, and use a stable analog reference and suitable input conditioning. Verify acquisition settling against the highest source impedance used in the design.

Calculate the analog error budget with the multiplexer's 3 kOhm on-resistance and the source impedance rather than treating 3 kOhm as negligible. For a source near 100 kOhm, the switch resistance introduces a substantial divider with the input resistance of the following amplifier or converter. Include leakage from the other seven channels when working with high-impedance sensors, and allow sufficient acquisition time after changing the latched address before taking the measurement.

Maintain the 18-pin PDIP footprint exactly when substituting a drop-in candidate. Confirm each package pin against the manufacturer pin-description table rather than relying only on the DIP outline, because the MAX388 family's address, latch, enable and analog pins must correspond correctly. For legacy repair work, inspect socket contacts, board contamination and bent pins; a mechanically similar package cannot compensate for an incorrect control-net assignment or incompatible maximum rating.

Establish the supply, enable and analog-input sequencing before power is applied. Because the device is designed for fault protection when inputs remain energized after power removal, the system must not assume that every internal transistor remains off under every possible ramp condition. Use controlled power sequencing where required, observe the absolute maximum ratings, and place the device within a lifecycle plan that accounts for its obsolete status and the sourcing of a qualified replacement.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The MAX388 product page identifies the family as obsolete. RoHS, REACH, lead-free, halogen-free and conflict-minerals status are not confirmed for this exact ordering code.

Data verified on: 2026-11-14 — data verified and curated by XAIPART's component engineering team

Related Searches

MAX388EPN+ datasheet MAX388EPN+ pinout MAX388EPN+ datasheet pdf MAX388EPN+ replacement MAX388EPN+ equivalent MAX388EPN+ vs MAX388CPN+ MAX388EPN+ price MAX388EPN+ stock Analog Devices MAX388EPN+ MAX388EPN+ 18-pin PDIP MAX388EPN+ 8:1 multiplexer MAX388EPN+ application circuit

Related Components & Terms

Analog Devices MAX388EPN+ MAX388EPN MAX388CPN+ MAX388 analog multiplexer multiplexer interface IC analog switch 8:1 multiplexer single-ended analog signal internal data latch high-voltage fault protection series N-channel switch series P-channel switch 3 kOhm on-resistance 18-pin PDIP DIP package through-hole package industrial instrumentation multi-sensor measurement test and measurement power-off channel protection obsolete product status
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details