MC14066BD - 3-18V Quad Analog Switch | onsemi | SOIC-14
MPN: MC14066BD ✓ ActiveMC14066BD Overview
An analog switch is a semiconductor device that routes a signal between circuit nodes under digital control. The MC14066BD belongs to the analog switch and multiplexer hierarchy, which sits within interface ICs and broader logic semiconductor systems. Unlike a mechanical relay, its switching action is controlled by CMOS-compatible logic and is intended for compact signal-routing implementations. Its four independent switches allow one package to handle multiple gated channels without requiring four separate single-switch packages.
The key defining feature is the MC14066B family's pin-for-pin compatibility with the onsemi MC14016B. The manufacturer states that the MC14066B provides substantially lower ON resistance than the MC14016B while retaining compatibility between the two devices. Its 3-18 V operating range supports both lower-voltage CMOS logic systems and higher-voltage analog signal-routing systems. Each of the four switches has a separate control input, allowing independent routing decisions within one circuit.
The MC14066BD uses parallel MOSFET-style switch elements to provide bilateral signal paths. A control signal determines whether the corresponding path is ON or OFF, and the switched signal can travel in either direction. This bilateral behavior makes the device suitable for signal gating, multiplexed test paths, chopper functions, modulation and demodulation stages, and general CMOS logic implementations where multiple analog or logic nodes must be routed independently.
Typical uses include switching sensor outputs in industrial measurement systems, routing audio-range signals in test equipment, selecting external networks in control circuits, and implementing modulator or demodulator functions. Because the control inputs operate from the same supply family as the signal paths, system designers should account for input logic levels, permissible signal excursions, ON-resistance effects, and off-state leakage when choosing external bias and interface components.
For PCB implementation, place the device so that switched signal traces remain short and away from high-current switching nodes. Use a common ground reference and provide a clean supply connection where logic thresholds matter. Confirm the exact pin assignment, electrical limits, and recommended operating conditions in the onsemi MC14066B datasheet before finalizing signal amplitude, control timing, and external resistor values.
This page consolidates the manufacturer’s core switch characteristics, package information, pin-compatibility guidance, application contexts, and design considerations into an engineering-focused selection reference. It also distinguishes the verified MC14016B relationship from unsupported substitutions, helping designers identify where a board-level change can be evaluated without relying on a generic cross-reference listing.
Drop-in alternatives for MC14066BD — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
MC14016B
✅ Drop-In📋 Reference alternative (not in catalog)
MC14066BD Maximum Ratings & Electrical Characteristics
| Product Type | Quad analog switch and quad multiplexer |
| Number of Switches | 4 independent switches |
| Switch Configuration | 4 independent SPST bilateral switches |
| Operating Supply Voltage Range | 3 V to 18 V |
| Package | 14-pin SOIC |
| Pin Count | 14 pins |
| Mounting Type | Surface mount |
| Signal Path | Bilateral; supports analog or digital signals |
| Control | One independent control input per switch |
| Maximum Controlled Signal Swing | Up to the full supply voltage |
| Logic Family | CMOS |
| Pin Compatibility | Pin-for-pin compatible with onsemi MC14016B |
MC14066BD 14-pin soic Pin Configuration Guide
Pin configuration for MC14066BD (14-pin soic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MC14066BD.
Refer to the datasheet for full pin configuration.
Typical Applications
MC14066BD is suitable for 6 applications: Analog Signal Gating, Chopper and Modulator Circuits, Demodulator Signal Routing, Industrial Sensor Signal Selection, CMOS Logic Signal Routing, Test and Measurement Signal Gating.
Analog Signal Gating
The MC14066BD is appropriate when several analog or logic paths must be switched under independent control. Its four bilateral switches operate from a 3-18 V supply, and each channel has a dedicated control input, allowing a single 14-pin SOIC to replace four separate single-switch packages. This reduces board area while preserving independent routing decisions. Engineers should verify the signal amplitude, ON resistance, control thresholds, and leakage for the operating point before finalizing the analog path.
Recommended
Chopper and Modulator Circuits
The four independent bilateral switches in the MC14066BD can construct switching functions used in chopper, modulator, and demodulator signal paths. Its 3-18 V operating range allows the device to operate alongside conventional CMOS logic, while signal excursions as large as the full supply voltage can be controlled. A practical design must account for control timing and switch resistance so that modulation waveform edges and amplitude remain acceptable at the intended operating conditions.
Recommended
Demodulator Signal Routing
A demodulator or gain-control implementation can use the MC14066BD to route a controlled input across one of four signal paths. Each switch has an independent control input, permitting separate timing and routing decisions within a compact 14-pin SOIC footprint. Because the device is bilateral, the switch paths are not restricted to a one-way signal direction. Confirm the acceptable logic levels and permitted signal excursion in the onsemi MC14066B datasheet when operating near supply limits.
Recommended
Industrial Sensor Signal Selection
The MC14066BD can gate sensor signals or select among conditioned measurement paths in industrial equipment. Four independently controlled channels provide useful routing flexibility, and the 3-18 V supply range supports both logic-level control and higher-voltage systems. The 14-pin SOIC package simplifies board-level integration, but signal integrity depends on keeping switched traces short, providing a stable ground reference, and reviewing leakage and ON resistance at the actual sensor amplitude.
Recommended
CMOS Logic Signal Routing
The MC14066BD is suitable for CMOS logic routing because each of its four switches is independently controlled and can handle digital as well as analog signals. The device supports bidirectional paths, making it useful when a logic node must be connected to one of several destinations. Its 3-18 V range spans common CMOS supply environments. Designers should use the manufacturer control-input thresholds to guarantee reliable recognition of every logic state and should avoid excessive loading on the switched node.
Recommended
Test and Measurement Signal Gating
Instrumentation designs can use the MC14066BD to gate or multiplex test signals among multiple circuit paths. Independent controls allow each of the four bilateral switches to represent a separately managed routing function, while the 14-pin SOIC package limits board area. When switching low-level or high-impedance signals, review ON resistance, leakage, control timing, and the maximum controlled signal excursion in the datasheet. Keep sensitive routes short and isolated from noisy switching nodes to preserve measurement quality.
Recommended
Engineering reference data for MC14066BD — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MC14016B |
|---|---|---|
| Brand | onsemi | onsemi |
| Package | 14-pin SOIC | 14-pin SOIC |
| ON Resistance | Lower than MC14016B | Higher than MC14066B |
| Pin Compatibility | Pin-for-pin compatible with MC14016B | Pin-for-pin compatible with MC14066B |
Key Differentiators
- Lower ON resistance than the pin-compatible MC14016B (vs MC14016B)
- Four independent bilateral switches in one package (vs MC14016B)
- Three- to 18-volt operating range (vs MC14016B)
Design Notes
Do not select the MC14016B as a substitute without checking the ON-resistance difference. The onsemi MC14066B datasheet states that the MC14066B is pin-for-pin compatible with the MC14016B but has much lower ON resistance. The substitution is therefore electrically attractive for routing, yet it can change signal attenuation, level loss, and effective source impedance. Confirm the numerical resistance under the intended supply and control voltages before approving the change.
Keep switched-node traces short and avoid routing them beside high-current or fast-switching nets. Although the MC14066BD supports signal swings as large as the full supply voltage, capacitance introduced by long PCB traces can increase control-edge timing effects and allow coupling into the gated signal. Use a continuous ground reference, minimize loop area, and place the device close to the signal source when working with low-level or high-impedance paths.
Assign every connection from the 14-pin SOIC pin-description table before routing the board, including the four control inputs, four bilateral switch paths, supply, and ground. Do not infer a pin assignment from the four-channel functional description alone. Preserve a straightforward flow from the controller outputs to the control pins and maintain a low-impedance ground connection so that the CMOS switching thresholds remain predictable under noisy or high-impedance conditions.
Compliance Information
The onsemi product page and MC14066B datasheet are the authoritative sources for environmental and material compliance. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for the exact MC14066BD ordering code were not confirmed.