Microchip Technology

MCP6042-E/MS - Dual 14kHz Low-Power R-R Op Amp | Microchip

MPN: MCP6042-E/MS ✓ Active
<3 mV Vdss 600 nA Id 8-pin MSOP Package
MOQ: 1 |

MCP6042-E/MS Overview

The Microchip Technology MCP6042-E/MS is a dual CMOS operational amplifier with a 14 kHz gain-bandwidth product, typical operating current of 600 nA, input offset voltage below 3 mV, and rail-to-rail input and output operation. The device is supplied in an 8-pin MSOP package, making it suitable for compact, low-power analog signal-conditioning systems.

An operational amplifier, or op amp, is a voltage-gain element that uses high open-loop gain to amplify small input differences. The MCP6042 belongs to the CMOS operational-amplifier hierarchy, where low bias current and low quiescent current are the defining priorities for battery-powered and high-impedance instrumentation. Rail-to-rail input capability allows the amplifier to operate close to the supply limits, while rail-to-rail output reduces clipping in low-voltage, single-supply applications.

The MCP6042-E/MS combines a 14 kHz gain-bandwidth product with a typical operating current of 600 nA. According to the Microchip MCP6042 product page, the device uses advanced CMOS technology to provide low bias current, high open-loop gain, high-speed operation, and a rail-to-rail output swing. The input offset voltage is specified below 3 mV, making the amplifier appropriate for sensor interfaces, current measurements, and low-frequency filtering rather than precision instrumentation requiring very small offsets.

Operation from a single supply as low as 1.4 V supports energy-efficient systems with limited rail headroom. Two independent amplifiers are integrated into one package, reducing board area for dual-channel sensing, differential buffering, and complementary signal conditioning. The 8-pin MSOP outline supports surface-mount assembly, while its low operating current helps conserve energy when the signal path is continuously active.

Typical uses include battery-powered sensor interfaces, portable measurement modules, low-current transducers, buffered analog controls, and general-purpose low-frequency amplification. Because its 14 kHz bandwidth is modest compared with general-purpose high-speed amplifiers, the MCP6042 is best selected where low quiescent current, rail-to-rail operation, and compact dual-channel integration matter more than wideband performance.

Design the input network to limit parasitic capacitance and leakage, especially when source impedances are high. Place the bypass capacitor close to the supply pin, maintain adequate output-load margin, and verify stability with the actual feedback network, source impedance, and capacitive load. This page combines the manufacturer specifications, package details, sourcing guidance, replacement constraints, and application-oriented design guidance needed to evaluate the MCP6042-E/MS.

Drop-in alternatives for MCP6042-E/MS — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MCP6042-E/MS (same form factor and footprint) — differing in Amplifier Type, Input Offset Voltage, Output Swing, Typical Operating Current.

Microchip Technology
Amplifier Type: General-purpose operational amplifier
Input Offset Voltage: Less than 3 mV
Output Swing: Rail-to-rail output

MCP6042-I/MS

✅ Drop-In
Microchip Technology
📦 8-pin MSOP
General-purpose operational amplifier · 2 channels · 14 kHz · 3 V/µs · 600 nA per amplifier · 1 pA typical · Less than 3 mV · 1.4 V to 5.5 V

Contact for price

View Datasheet →

MCP6042-E/MS Maximum Ratings & Electrical Characteristics

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 14 kHz
Typical Operating Current 600 nA
Input Offset Voltage <3 mV
Output Swing Rail-to-rail
Input Range Rail-to-rail
Minimum Supply Voltage 1.4 V
Maximum Supply Voltage 6 V
Technology CMOS
Package 8-pin MSOP
Mounting Type Surface mount

MCP6042-E/MS 8-pin msop Pin Configuration Guide

Pin configuration for MCP6042-E/MS (8-pin msop package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

8-pin msop package pinout diagram for MCP6042-E/MS

No detailed pinout data available for MCP6042-E/MS.

Refer to the datasheet for full pin configuration.

Typical Applications

MCP6042-E/MS is suitable for 6 applications: Battery-Powered Sensor Buffering, Portable Medical Monitoring, Industrial Current-Sensing Interface, Low-Voltage Control Signal Buffer, Portable Instrumentation Front End, IoT Sensor Node Interface.

🔋

Battery-Powered Sensor Buffering

The MCP6042-E/MS fits low-power sensor front ends because its 600 nA typical operating current minimizes continuous drain and its 1.4 V minimum supply voltage supports low-voltage battery systems. Two channels can buffer closely related sensor outputs without requiring two packages, reducing board area. The rail-to-rail input and output behavior helps preserve signal range in single-supply designs. Because the gain-bandwidth product is 14 kHz, the device is best suited to temperature, pressure, and chemical sensors with slow bandwidth rather than rapidly changing signals. The engineer should also verify input bias current against the sensor source impedance.

💊

Portable Medical Monitoring

The MCP6042-E/MS can condition the slow, low-amplitude signals found in portable monitoring equipment while keeping two amplifier channels in one compact 8-pin MSOP package. Its 600 nA typical operating current is valuable when the instrument operates continuously from a limited battery budget, and rail-to-rail operation accommodates small signals on a low-voltage supply. The MCP6042 is appropriate for low-bandwidth sensor channels rather than diagnostic waveforms requiring rapid settling. Input bias current, noise, and common-mode behavior must be checked against the selected sensor and the required medical-system design controls.

🏭

Industrial Current-Sensing Interface

The MCP6042-E/MS is suitable for low-bandwidth current-sense amplifier stages in industrial monitoring systems because the two channels can process complementary or differential measurements in a compact package. Its 14 kHz gain-bandwidth product is appropriate for signals whose useful content remains well below that frequency, and the low operating current reduces auxiliary power in distributed sensor nodes. Rail-to-rail input operation helps maximize signal utilization on low-voltage supplies. The actual shunt impedance, amplifier offset below 3 mV, input bias current, and output load must be evaluated to determine whether the error budget meets the application requirements.

⚙️

Low-Voltage Control Signal Buffer

The MCP6042-E/MS can buffer low-level control signals from sensors, dividers, and simple DAC outputs when the required bandwidth is modest. The dual amplifier provides independent channels for a signal and its reference or for two related control paths, while the 8-pin MSOP package supports compact PCB layouts. Operation from 1.4 V and rail-to-rail output make the device useful in low-voltage embedded systems. Designers should confirm output drive and stability with the connected load, and should not use the 14 kHz device where fast edges or high capacitive loads require a wider-bandwidth amplifier.

🖥️

Portable Instrumentation Front End

The MCP6042-E/MS suits portable instrumentation that combines two low-frequency analog channels with strict power constraints. Its dual architecture reduces component count, while 600 nA typical operating current leaves more of the battery budget for the sensor and display. The 14 kHz gain-bandwidth product can support gain stages and gentle active filtering around slow process or laboratory signals. Because input offset voltage is specified below 3 mV, applications requiring very high absolute accuracy should calculate resistor matching, bias-current error, and drift before selecting it. The MSOP outline also helps minimize board area in handheld instruments.

🧩

IoT Sensor Node Interface

The MCP6042-E/MS is well matched to compact IoT sensor nodes that condition two slow analog channels before conversion or digital sampling. Low power is central because the amplifier can operate with only 600 nA typical current, and the 1.4 V minimum supply supports aggressively partitioned low-voltage systems. Rail-to-rail inputs improve utilization of the available signal range, while the dual MSOP package conservates area. Leakage and bias current become more important as the sensor impedance rises, so high-impedance sources should be evaluated carefully. A sampling system with demanding acquisition bandwidth will need a faster amplifier instead.

Recommended Products Summary

MCP6041 Single-channel member of the same low-power CMOS operational-amplifier family Used in: Battery-Powered Sensor Buffering, Portable Medical Monitoring, Industrial Current-Sensing Interface, Low-Voltage Control Signal Buffer, Portable Instrumentation Front End, IoT Sensor Node Interface MCP6043 Single-channel family member with chip-select functionality Used in: Battery-Powered Sensor Buffering, Industrial Current-Sensing Interface, IoT Sensor Node Interface MCP6044 Quad low-power family member for multi-channel monitoring systems Used in: Portable Medical Monitoring, Portable Instrumentation Front End MCP6042 Base dual-amplifier family designation Used in: Low-Voltage Control Signal Buffer
What are the key specifications of MCP6042-E/MS that engineers should know?
The MCP6042-E/MS is a dual, low-power CMOS operational amplifier with a 14 kHz gain-bandwidth product, 600 nA typical operating current, input offset voltage below 3 mV, and rail-to-rail input and output operation. According to the Microchip MCP6042 product page, it also provides high open-loop gain and operates from a 1.4 V single supply. The device is packaged in an 8-pin MSOP, making it most appropriate for low-frequency sensor buffering, portable instrumentation, and other applications where dual-channel integration and low current consumption are more important than high-speed amplification.
What is the MCP6042-E/MS operational amplifier used for?
The MCP6042-E/MS is used for low-frequency signal amplification in compact, low-power systems. Its two independent amplifier channels can handle sensor inputs, buffered controls, transducer outputs, and complementary analog channels. The 14 kHz gain-bandwidth product supports low-frequency gain and filtering stages, while 600 nA typical operating current helps preserve battery life. According to the Microchip MCP6042 product page, rail-to-rail input and output operation is particularly useful in low-voltage systems where the signal can approach either supply rail.
What is the supply voltage range of MCP6042-E/MS?
The MCP6042-E/MS operates from a 1.4 V to 6 V single supply. This low-voltage range allows the amplifier to be used with coin cells, energy-harvesting supplies, and low-voltage sensor rails. The Microchip MCP6042 family uses CMOS technology and supports rail-to-rail operation, making the device suitable for systems where the usable signal occupies much of the available supply range. The exact operating-temperature limits and maximum supply conditions should be confirmed in the manufacturer datasheet before final circuit release.
What is the gain-bandwidth product of MCP6042-E/MS?
The MCP6042-E/MS has a 14 kHz gain-bandwidth product. According to the Microchip MCP6042 product page, this bandwidth is intended for low-frequency precision and signal-conditioning applications rather than wideband waveform amplification. Closed-loop bandwidth depends on the selected noise gain, so a 10x noninverting stage would have approximately 1.4 kHz bandwidth before gain-bandwidth-product effects. Confirm stability and usable bandwidth with the selected feedback topology and the intended source and load impedances.
How much current does MCP6042-E/MS consume?
The MCP6042-E/MS consumes 600 nA of typical operating current. According to the Microchip MCP6042 product page, the low operating current results from its advanced CMOS implementation. The family can draw less than 1 µA maximum per amplifier, according to the family information represented in the cross-reference results. Actual current depends on supply voltage, output state, input bias, and switching activity, so power-budget calculations should include the worst-case operating state specified by the manufacturer.
Does MCP6042-E/MS support rail-to-rail input and output?
Yes, the MCP6042-E/MS supports rail-to-rail input and output operation. According to the Microchip MCP6042 product page, its CMOS design provides a rail-to-rail output swing and low bias current. This capability is valuable in single-supply circuits where the input may span nearly the full available signal range and the output must remain close to the load limits. Designers should still check input and output absolute-maximum ratings, common-mode behavior, and output load capability in the manufacturer datasheet.
Where can I download the MCP6042 datasheet PDF?
The official MCP6042 datasheet and product resources are available from the Microchip Technology product page at https://www.microchip.com/en-us/product/MCP6042. Use the datasheet link on that page for the authoritative PDF, ordering information, package drawings, and electrical characteristics. The MCP6042-E/MS ordering code identifies the dual device in an 8-pin MSOP package. Pin assignments, recommended operating conditions, and absolute-maximum limits should be taken from the package-specific documentation associated with that ordering code.
Where can I find the MCP6042 pinout?
The MCP6042 pinout is shown in the pin-description and package-drawing sections of the Microchip MCP6042 datasheet. The MCP6042-E/MS uses an 8-pin MSOP package, and the datasheet provides the authoritative numbering for both amplifier channels, supply connections, and no-connect positions. Use that pin-description table when assigning PCB tracks because package drawings and datasheet revisions are the controlling references for physical implementation.
What is the best drop-in replacement for MCP6042-E/MS?
The closest documented same-package replacement is MCP6042-I/MS, which retains the dual 8-pin MSOP arrangement but changes the operating-temperature grade. A drop-in replacement should also match the 1.4 V to 6 V supply range, 14 kHz gain-bandwidth product, rail-to-rail operation, and channel pin arrangement. The manufacturer cross-reference search should be used to confirm current substitutions because suffix changes can affect temperature grade, qualification, or packing. No additional drop-in equivalents were confidently established for the exact MCP6042-E/MS ordering code.
Can MCP6042-I/MS replace MCP6042-E/MS?
MCP6042-I/MS can serve as a same-footprint candidate, but its temperature grade differs from MCP6042-E/MS. The electrical core remains a dual rail-to-rail CMOS operational amplifier in an 8-pin MSOP, while the suffix change indicates a different temperature grade. Before substituting it, verify the required ambient range, operating limits, and production qualification in the Microchip documentation. The E/MS and I/MS options should not be treated as equivalent for an extended-temperature design without that review.
MCP6042-E/MS vs MCP6042-I/MS: which is better for an industrial design?
Choose MCP6042-E/MS when the design requires the higher-temperature E-grade option, and choose MCP6042-I/MS when the I-grade operating range covers the product environment. Both use the dual 8-pin MSOP architecture and belong to the 14 kHz, 600 nA CMOS family. According to the Microchip MCP6042 family information, both support operation from 1.4 V and rail-to-rail signal handling. The selection should be based on the verified temperature limits and qualification requirements for the final product.
When should I choose MCP6042-E/MS instead of a higher-bandwidth op amp?
Choose MCP6042-E/MS when the circuit operates at low frequencies and battery life, compactness, or rail-to-rail single-supply performance is more important than bandwidth. Its 14 kHz gain-bandwidth product and 600 nA typical operating current suit slow sensor signals and low-duty analog channels. Select a higher-bandwidth amplifier instead when the required closed-loop bandwidth, slew rate, settling time, or capacitive-load drive exceeds the MCP6042's capability.
Is MCP6042-E/MS suitable for battery-powered sensor interfaces?
Yes, MCP6042-E/MS is suitable for many battery-powered sensor interfaces. Its 600 nA typical operating current minimizes continuous circuit load, and the 1.4 V minimum supply voltage supports low-voltage energy sources. Rail-to-rail input and output operation can improve usable signal range in single-supply sensor circuits. High source impedances still require attention because input bias current and leakage determine the achievable sensor accuracy; verify those parameters and the complete power budget before production.
Where can I buy MCP6042-E/MS online?
Use the Request a Quote form on this page to request MCP6042-E/MS availability, order quantity, and current lead time. The form supports a direct sourcing response without presenting a static or potentially stale commercial listing. Buyers should specify the exact MCP6042-E/MS ordering code and the required tube quantity. If production quantities or scheduling are unusual, include the target build date so the sourcing response can account for procurement lead time.
What is the price of MCP6042-E/MS?
The current commercial price for MCP6042-E/MS should be requested through the Request a Quote form on this page. Quote-based handling allows the order quantity, current inventory position, and procurement date to be considered without embedding a price that can quickly become inaccurate. Provide the exact MPN and packaging requirement when submitting the request so the returned quotation corresponds to the 8-pin MSOP device rather than another member of the MCP6041/2/3/4 family.
What is the lead time and stock status of MCP6042-E/MS?
Current MCP6042-E/MS stock status and lead time should be confirmed through the Request a Quote form on this page. The request can identify the exact ordering code, tube quantity, annual demand, and required delivery date. This approach is preferable to relying on a static availability statement because distributor inventory and manufacturer lead times change. For new production programs, include the forecast and any approved alternate-part policy with the sourcing request.

Engineering reference data for MCP6042-E/MS — comparison, design guidance, and compliance information.

Selection Guide

Choose MCP6042-E/MS for compact, low-voltage designs needing two low-frequency amplifier channels, rail-to-rail input and output operation, and low power consumption. Its 600 nA typical operating current and 1.4 V minimum supply make it suitable for portable sensing, while the dual MSOP package saves board area. MCP6042-I/MS is a practical same-package candidate when its lower temperature grade covers the required environment. Use MCP6041 when only one channel is needed, MCP6043 when chip-select functionality is required, or MCP6044 when four channels justify the larger package. Do not select this family for high-speed signal chains, high-precision offset-sensitive measurements, or capacitive loads beyond the amplifier's stability limits. For those requirements, choose an amplifier with lower offset, higher bandwidth, faster slew rate, or stronger output-drive capability.

Comparison with Alternatives

Parameter This Product MCP6042-I/MS
Package 8-pin MSOP 8-pin MSOP
Brand Microchip Technology Microchip Technology
Number of Amplifiers 2 2
Gain-Bandwidth Product 14 kHz 14 kHz
Typical Operating Current 600 nA 600 nA
Input Offset Voltage <3 mV <3 mV
Supply Voltage Range 1.4 V to 6 V 1.4 V to 6 V
Input and Output Range Rail-to-rail Rail-to-rail

Key Differentiators

  • Combines two amplifier channels with very low operating current (vs MCP6042-I/MS)
  • Maintains the same core signal-path performance in the I-grade option (vs MCP6042-I/MS)
  • Supports compact dual-channel instrumentation (vs MCP6041)

Design Notes

Place the supply bypass capacitor directly between the MSOP supply and ground pins, with a short ground return and no unnecessary loop area. For low-frequency sensor interfaces, keep the amplifier input traces short and isolate them from switching nodes and digital clocks. The MCP6042-E/MS uses a 14 kHz gain-bandwidth product, so it is generally insensitive to ordinary board-level high-frequency coupling, but low-level inputs still benefit from a quiet, high-impedance layout.

Budget the MCP6042-E/MS using its 600 nA typical operating current and then check the worst-case current stated in the manufacturer datasheet. Include the quiescent current of both amplifier channels, divider current, feedback-network current, and load current in the total system calculation. A low-current amplifier does not guarantee low total supply consumption if the application continuously drives a resistive load.

Avoid long high-impedance input traces and unnecessary shunt capacitance, particularly when the source impedance is high. Calculate the bias-current-induced error across the effective source resistance and compare it with the signal budget. If the MCP6042-E/MS is used as a voltage follower, verify stability and bandwidth with the actual source impedance; very high source resistance can introduce parasitic capacitance that alters the closed-loop response.

Do not interpret the 14 kHz gain-bandwidth product as a 14 kHz closed-loop bandwidth at every gain. At a closed-loop gain of 10, the nominal bandwidth is approximately 1.4 kHz before additional real-world limitations. Also confirm that input and output operation near the rails remains within the manufacturer-recommended common-mode and load conditions. For signals above the device's useful bandwidth or for capacitive loads, select a wider-bandwidth amplifier.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

Compliance information was not explicitly stated in the available manufacturer page excerpt or distributor results. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals status using the current Microchip product documentation and material declarations.

Related Searches

mcp6042 datasheet mcp6042 datasheet pdf mcp6042 pinout MCP6042-E/MS specifications MCP6042-E/MS pinout MCP6042-E/MS MSOP package MCP6042-E/MS equivalent MCP6042-E/MS replacement MCP6042-E/MS vs MCP6042-I/MS MCP6042-E/MS price MCP6042-E/MS stock Microchip MCP6042 low power op amp

Related Components & Terms

Microchip Technology MCP6042-E/MS MCP6042 MCP6042-I/MS MCP6041 MCP6042 MCP6043 MCP6044 dual operational amplifier CMOS operational amplifier low-power op amp rail-to-rail input rail-to-rail output gain-bandwidth product quiescent current input offset voltage single-supply operation 8-pin MSOP MSOP package surface-mount package sensor interface portable instrumentation battery-powered circuit industrial current sensing RoHS REACH
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details