MCP6042-E/MS - Dual 14kHz Low-Power R-R Op Amp | Microchip
MPN: MCP6042-E/MS ✓ نشطMCP6042-E/MS نظرة عامة
An operational amplifier, or op amp, is a voltage-gain element that uses high open-loop gain to amplify small input differences. The MCP6042 belongs to the CMOS operational-amplifier hierarchy, where low bias current and low quiescent current are the defining priorities for battery-powered and high-impedance instrumentation. Rail-to-rail input capability allows the amplifier to operate close to the supply limits, while rail-to-rail output reduces clipping in low-voltage, single-supply applications.
The MCP6042-E/MS combines a 14 kHz gain-bandwidth product with a typical operating current of 600 nA. According to the Microchip MCP6042 product page, the device uses advanced CMOS technology to provide low bias current, high open-loop gain, high-speed operation, and a rail-to-rail output swing. The input offset voltage is specified below 3 mV, making the amplifier appropriate for sensor interfaces, current measurements, and low-frequency filtering rather than precision instrumentation requiring very small offsets.
Operation from a single supply as low as 1.4 V supports energy-efficient systems with limited rail headroom. Two independent amplifiers are integrated into one package, reducing board area for dual-channel sensing, differential buffering, and complementary signal conditioning. The 8-pin MSOP outline supports surface-mount assembly, while its low operating current helps conserve energy when the signal path is continuously active.
Typical uses include battery-powered sensor interfaces, portable measurement modules, low-current transducers, buffered analog controls, and general-purpose low-frequency amplification. Because its 14 kHz bandwidth is modest compared with general-purpose high-speed amplifiers, the MCP6042 is best selected where low quiescent current, rail-to-rail operation, and compact dual-channel integration matter more than wideband performance.
Design the input network to limit parasitic capacitance and leakage, especially when source impedances are high. Place the bypass capacitor close to the supply pin, maintain adequate output-load margin, and verify stability with the actual feedback network, source impedance, and capacitive load. This page combines the manufacturer specifications, package details, sourcing guidance, replacement constraints, and application-oriented design guidance needed to evaluate the MCP6042-E/MS.
بدائل مباشرة لـ MCP6042-E/MS — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MCP6042-E/MS (نفس عامل الشكل والبصمة) — يختلف في Amplifier Type, Input Offset Voltage, Output Swing, Typical Operating Current.
MCP6042-I/MS
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MCP6042-E/MS الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 14 kHz |
| Typical Operating Current | 600 nA |
| Input Offset Voltage | <3 mV |
| Output Swing | Rail-to-rail |
| Input Range | Rail-to-rail |
| Minimum Supply Voltage | 1.4 V |
| Maximum Supply Voltage | 6 V |
| Technology | CMOS |
| العلبة | 8-pin MSOP |
| نوع التركيب | Surface mount |
دليل تكوين أطراف MCP6042-E/MS 8-pin msop
تكوين الأطراف لـ MCP6042-E/MS (حزمة 8-pin msop). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MCP6042-E/MS.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MCP6042-E/MS مناسب لـ 6 التطبيقs: Battery-Powered Sensor Buffering, Portable Medical Monitoring, Industrial Current-Sensing Interface, Low-Voltage Control Signal Buffer, Portable Instrumentation Front End, IoT Sensor Node Interface.
Battery-Powered Sensor Buffering
The MCP6042-E/MS fits low-power sensor front ends because its 600 nA typical operating current minimizes continuous drain and its 1.4 V minimum supply voltage supports low-voltage battery systems. Two channels can buffer closely related sensor outputs without requiring two packages, reducing board area. The rail-to-rail input and output behavior helps preserve signal range in single-supply designs. Because the gain-bandwidth product is 14 kHz, the device is best suited to temperature, pressure, and chemical sensors with slow bandwidth rather than rapidly changing signals. The engineer should also verify input bias current against the sensor source impedance.
موصى به
Portable Medical Monitoring
The MCP6042-E/MS can condition the slow, low-amplitude signals found in portable monitoring equipment while keeping two amplifier channels in one compact 8-pin MSOP package. Its 600 nA typical operating current is valuable when the instrument operates continuously from a limited battery budget, and rail-to-rail operation accommodates small signals on a low-voltage supply. The MCP6042 is appropriate for low-bandwidth sensor channels rather than diagnostic waveforms requiring rapid settling. Input bias current, noise, and common-mode behavior must be checked against the selected sensor and the required medical-system design controls.
موصى به
Industrial Current-Sensing Interface
The MCP6042-E/MS is suitable for low-bandwidth current-sense amplifier stages in industrial monitoring systems because the two channels can process complementary or differential measurements in a compact package. Its 14 kHz gain-bandwidth product is appropriate for signals whose useful content remains well below that frequency, and the low operating current reduces auxiliary power in distributed sensor nodes. Rail-to-rail input operation helps maximize signal utilization on low-voltage supplies. The actual shunt impedance, amplifier offset below 3 mV, input bias current, and output load must be evaluated to determine whether the error budget meets the application requirements.
موصى به
Low-Voltage Control Signal Buffer
The MCP6042-E/MS can buffer low-level control signals from sensors, dividers, and simple DAC outputs when the required bandwidth is modest. The dual amplifier provides independent channels for a signal and its reference or for two related control paths, while the 8-pin MSOP package supports compact PCB layouts. Operation from 1.4 V and rail-to-rail output make the device useful in low-voltage embedded systems. Designers should confirm output drive and stability with the connected load, and should not use the 14 kHz device where fast edges or high capacitive loads require a wider-bandwidth amplifier.
موصى به
Portable Instrumentation Front End
The MCP6042-E/MS suits portable instrumentation that combines two low-frequency analog channels with strict power constraints. Its dual architecture reduces component count, while 600 nA typical operating current leaves more of the battery budget for the sensor and display. The 14 kHz gain-bandwidth product can support gain stages and gentle active filtering around slow process or laboratory signals. Because input offset voltage is specified below 3 mV, applications requiring very high absolute accuracy should calculate resistor matching, bias-current error, and drift before selecting it. The MSOP outline also helps minimize board area in handheld instruments.
موصى به
IoT Sensor Node Interface
The MCP6042-E/MS is well matched to compact IoT sensor nodes that condition two slow analog channels before conversion or digital sampling. Low power is central because the amplifier can operate with only 600 nA typical current, and the 1.4 V minimum supply supports aggressively partitioned low-voltage systems. Rail-to-rail inputs improve utilization of the available signal range, while the dual MSOP package conservates area. Leakage and bias current become more important as the sensor impedance rises, so high-impedance sources should be evaluated carefully. A sampling system with demanding acquisition bandwidth will need a faster amplifier instead.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MCP6042-E/MS — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MCP6042-I/MS |
|---|---|---|
| Package | 8-pin MSOP | 8-pin MSOP |
| Brand | Microchip Technology | Microchip Technology |
| Number of Amplifiers | 2 | 2 |
| Gain-Bandwidth Product | 14 kHz | 14 kHz |
| Typical Operating Current | 600 nA | 600 nA |
| Input Offset Voltage | <3 mV | <3 mV |
| Supply Voltage Range | 1.4 V to 6 V | 1.4 V to 6 V |
| Input and Output Range | Rail-to-rail | Rail-to-rail |
أبرز الفروقات
- Combines two amplifier channels with very low operating current (مقابلMCP6042-I/MS)
- Maintains the same core signal-path performance in the I-grade option (مقابلMCP6042-I/MS)
- Supports compact dual-channel instrumentation (مقابلMCP6041)
ملاحظات التصميم
Place the supply bypass capacitor directly between the MSOP supply and ground pins, with a short ground return and no unnecessary loop area. For low-frequency sensor interfaces, keep the amplifier input traces short and isolate them from switching nodes and digital clocks. The MCP6042-E/MS uses a 14 kHz gain-bandwidth product, so it is generally insensitive to ordinary board-level high-frequency coupling, but low-level inputs still benefit from a quiet, high-impedance layout.
Budget the MCP6042-E/MS using its 600 nA typical operating current and then check the worst-case current stated in the manufacturer datasheet. Include the quiescent current of both amplifier channels, divider current, feedback-network current, and load current in the total system calculation. A low-current amplifier does not guarantee low total supply consumption if the application continuously drives a resistive load.
Avoid long high-impedance input traces and unnecessary shunt capacitance, particularly when the source impedance is high. Calculate the bias-current-induced error across the effective source resistance and compare it with the signal budget. If the MCP6042-E/MS is used as a voltage follower, verify stability and bandwidth with the actual source impedance; very high source resistance can introduce parasitic capacitance that alters the closed-loop response.
Do not interpret the 14 kHz gain-bandwidth product as a 14 kHz closed-loop bandwidth at every gain. At a closed-loop gain of 10, the nominal bandwidth is approximately 1.4 kHz before additional real-world limitations. Also confirm that input and output operation near the rails remains within the manufacturer-recommended common-mode and load conditions. For signals above the device's useful bandwidth or for capacitive loads, select a wider-bandwidth amplifier.
معلومات الامتثال
Compliance information was not explicitly stated in the available manufacturer page excerpt or distributor results. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals status using the current Microchip product documentation and material declarations.