Microchip Technology

MCP6042-E/SN - Dual 14kHz Low-Power RRIO Op Amp | Microchip

MPN: MCP6042-E/SN ✓ Active
1.4 V Vdss 600 nA per amplifier Id 8-pin SOIC, 3.90 mm width Package
MOQ: 1 |

MCP6042-E/SN Overview

The Microchip Technology MCP6042-E/SN is a dual, general-purpose operational amplifier with a 14 kHz gain-bandwidth product, typical operating current of 600 nA per amplifier, and rail-to-rail input and output operation in an 8-pin SOIC package. The device supports single-supply operation from 1.4 V and is intended for low-voltage, low-power signal-conditioning systems.

An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and drive signals. The MCP6042 belongs to the CMOS operational-amplifier family within the broader voltage-regulator and power-management IC ecosystem. Its dual-channel configuration provides two amplifiers in one package, reducing board area when a system needs signal conditioning on multiple low-voltage rails.

The MCP6042-E/SN combines a 14 kHz gain-bandwidth product with a typical operating current of 600 nA. According to the Microchip manufacturer product page, input offset voltage is less than 3 mV, while the family operates from a single supply as low as 1.4 V and draws less than 1 µA maximum quiescent current per amplifier. Rail-to-rail input and output stages allow the amplifier to operate close to the supply rails.

The MCP6042 uses Microchip's advanced CMOS technology. This rail-to-rail architecture supports low-voltage battery-powered designs where usable signal range, supply headroom, and current consumption are important. Because its bandwidth is intentionally modest, the device is best suited to low-frequency precision and general-purpose functions rather than high-speed signal conditioning.

Typical uses include battery-powered instrumentation, sensor interfaces, low-frequency active filters, current-to-voltage conversion, comparators, audio input conditioning, and portable measurement systems. The dual topology is particularly useful when two related analog channels must share the same package, supply voltage, and operating-current budget.

Design the surrounding network for the MCP6042's gain-bandwidth and output-current limits, and place input, feedback, and bypass components close to the device to reduce parasitic feedback. Verify the required source and sink current into the output at the selected load because rail-to-rail operation simplifies signal range but does not remove output-drive limitations.

This product page combines manufacturer specifications, sourcing guidance, drop-in replacement analysis, application examples, and practical PCB considerations to support faster engineering decisions beyond the basic datasheet feature list.

Drop-in alternatives for MCP6042-E/SN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MCP6042-E/SN (same form factor and footprint) — differing in Maximum Quiescent Current, Package.

Microchip Technology
Maximum Quiescent Current: 1 µA per amplifier
Package: 8-SOIC, 3.90 mm width

MCP6042-I/SN

✅ Drop-In
Microchip Technology
📦 8-SOIC
General-purpose operational amplifier · 2 · 14 kHz · 600 nA per amplifier · 1 µA per amplifier · 1.4 V · Less than 3 mV · 1 pA

Contact for price

View Datasheet →

MCP6042T-E/SN

✅ Drop-In
📦 8-SOIC
Same E-grade dual 8-SOIC electrical configuration and 14 kHz class of operation; only the shipping format changes from tube to tape and reel, with no electrical difference quantified

📋 Reference alternative (not in catalog)

MCP6042-E/SN Maximum Ratings & Electrical Characteristics

Number of Amplifiers 2
Product Type General-purpose operational amplifier
Gain-Bandwidth Product 14 kHz
Typical Operating Current 600 nA per amplifier
Maximum Quiescent Current <1 µA per amplifier
Minimum Single-Supply Voltage 1.4 V
Typical Input Offset Voltage <3 mV
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Process Technology Advanced CMOS
Package 8-pin SOIC, 3.90 mm width
Mounting Type Surface mount
Operating Temperature Grade E temperature grade

MCP6042-E/SN 8-pin soic, 3.90 mm width Pin Configuration Guide

Pin configuration for MCP6042-E/SN (8-pin soic, 3.90 mm width package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

8-pin soic, 3.90 mm width package pinout diagram for MCP6042-E/SN

No detailed pinout data available for MCP6042-E/SN.

Refer to the datasheet for full pin configuration.

Typical Applications

MCP6042-E/SN is suitable for 6 applications: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Low-Level Signal Conditioning, Current-to-Voltage Conversion, Low-Frequency Active Filtering, Audio Input Conditioning.

🧩

Battery-Powered Sensor Conditioning

The MCP6042-E/SN fits battery-powered sensor interfaces because each amplifier draws 600 nA typical operating current and the family operates from 1.4 V. Rail-to-rail input and output stages preserve signal range when the sensor output lies near the supply rails. A typical circuit buffers a high-impedance sensor, scales its voltage, and drives the input of a low-power converter or data-capture stage. The main design consideration is bandwidth: the 14 kHz gain-bandwidth product is suitable for slow environmental or biometric signals, but it is not appropriate for fast pulse signals or wideband sensor acquisition.

💊

Portable Medical Monitoring

The MCP6042-E/SN is useful in portable medical monitoring circuits where each channel must operate from limited current and voltage. Its less-than-1 µA maximum quiescent current per amplifier and 600 nA typical operating current reduce amplifier contribution to total system load, while rail-to-rail operation supports low-amplitude signals close to the supply limits. The dual package can condition two related sensor channels in a compact medical device. Engineers should verify medical qualification requirements, input offset, noise, isolation barriers, and patient-safety standards because the amplifier ordering code alone does not establish compliance for the finished instrument.

🏭

Industrial Low-Level Signal Conditioning

The MCP6042-E/SN can amplify low-level signals in industrial measurement systems when operating speed and current draw are more important than wide bandwidth. Its less-than-3 mV typical input offset and 14 kHz gain-bandwidth product suit slow pressure, temperature, and position sensing interfaces. The amplifier may provide buffering, gain, or active filtering before a higher-resolution converter. Layout must keep the 8-SOIC away from motor-control and relay-switching circuitry, and the external feedback network must be designed around the 14 kHz bandwidth to avoid unintended oscillation or excessive noise gain.

⚡

Current-to-Voltage Conversion

The MCP6042-E/SN is appropriate for low-frequency current-to-voltage conversion in electrochemical, battery-fabrication, and laboratory instrumentation. Its rail-to-rail input allows a small shunt voltage to be amplified without requiring a mid-supply bias, and the dual configuration can handle two current channels where monitoring symmetry matters. The 14 kHz gain-bandwidth product constrains closed-loop bandwidth and settling behavior, so the feedback resistor and compensation capacitor must be calculated for the required measurement rate. Input bias current and offset should also be checked against the shunt impedance to avoid measurement errors.

🎧

Low-Frequency Active Filtering

The MCP6042-E/SN can implement first- or second-order active filters for slow analog signals because it provides two amplifiers with a 14 kHz gain-bandwidth product. Rail-to-rail input and output operation makes it useful for filters processing signals near a low supply rail. Component tolerances and the amplifier's finite gain-bandwidth response determine actual cutoff accuracy and phase margin. Test the filter across its intended frequency range, keep the signal path compact, and avoid placing high-gain stages too close to switching regulators or digital clock lines.

🎧

Audio Input Conditioning

The MCP6042-E/SN can condition low-level audio or microphone signals when the design prioritizes low supply voltage and low current over wide bandwidth. Rail-to-rail input and output operation improves headroom in single-supply audio paths, while the dual amplifier can support stereo or balanced signal conditioning. The 14 kHz gain-bandwidth product limits useful signal bandwidth and may introduce phase shift near the upper edge of the audio range. Confirm the required audio-band performance, input noise, channel matching, output loading, and coupling-capacitor strategy before using it in a precision audio design.

What are the key specifications of MCP6042-E/SN that engineers should know?
The MCP6042-E/SN is a dual, rail-to-rail CMOS operational amplifier with a 14 kHz gain-bandwidth product, 600 nA typical operating current per amplifier, and input offset voltage below 3 mV. According to the Microchip manufacturer product page, the family supports single-supply operation from 1.4 V and consumes less than 1 µA maximum quiescent current per amplifier. It is packaged in an 8-pin SOIC for conventional surface-mount assembly.
What is the operating voltage of MCP6042-E/SN?
The MCP6042-E/SN operates from a single supply as low as 1.4 V. According to the Microchip MCP6042 product page, the device uses rail-to-rail input and output stages, allowing signals to approach the supply limits at the input and output. The maximum rated supply voltage should be confirmed against the manufacturer datasheet before applying the amplifier outside the stated operating range.
How much current does MCP6042-E/SN consume?
The MCP6042-E/SN draws 600 nA typical operating current per amplifier. The MCP6042 family specification states less than 1 µA maximum quiescent current per amplifier. This low-current characteristic is particularly useful for battery-powered instrumentation, portable sensors, and low-leakage measurement circuits where every microamp contributes to the system's operating time.
Is MCP6042-E/SN suitable for battery-powered applications?
Yes, the MCP6042-E/SN is well suited to battery-powered applications because it operates from 1.4 V and consumes 600 nA typical current per amplifier. Its rail-to-rail input and output operation improves usable signal range in low-voltage systems. The complete power budget should also include sensor current, pull-up resistors, leakage, and the amplifier's output-load requirements.
Where can I download the MCP6042 datasheet PDF?
The official MCP6042 datasheet is available through the Microchip manufacturer product page at https://www.microchip.com/en-us/product/MCP6042. The page contains the family documentation and device information for the MCP6041, MCP6042, MCP6043, and MCP6044 amplifiers. Use the manufacturer document-selection controls to choose the specific package and temperature-grade variant corresponding to MCP6042-E/SN.
Where can I find the MCP6042 pinout?
The MCP6042 pinout is shown in the manufacturer datasheet available from the Microchip MCP6042 product page. The MCP6042-E/SN uses an 8-pin SOIC with two operational amplifiers, and the pin-description table should be used when assigning inputs, outputs, supply pins, and no-connect positions on the PCB. Do not infer the dual-amplifier pinout from a single-amplifier package without checking the specific drawing.
What is the gain-bandwidth product of MCP6042-E/SN?
The MCP6042-E/SN has a 14 kHz gain-bandwidth product. According to the Microchip manufacturer product page, this bandwidth supports low-frequency analog signal conditioning while consuming 600 nA typical current per amplifier. The product is therefore appropriate for sensor buffers, slow comparators, low-frequency filters, and precision conditioning rather than wideband video or high-speed communications.
What can replace MCP6042-E/SN?
A valid replacement must use the same 8-pin SOIC footprint, preserve pin-to-pin connectivity, and remain electrically comparable. MCP6042-I/SN is a same-package Microchip option with a different temperature-grade designation, while MCP6042T-E/SN preserves the electrical configuration but changes the shipping format from tube to tape and reel. Verify the exact pinout, supply limits, offset, bandwidth, output drive, and production documentation before replacing the assembled part.
Is MCP6042-E/SN the same as MCP6042-I/SN?
MCP6042-E/SN and MCP6042-I/SN are variants of the same dual Microchip operational-amplifier family and use the 8-pin SOIC package. Their temperature-grade designations differ, with the E variant intended for the extended-temperature application identified by its ordering code and the I variant carrying the industrial-grade designation. Confirm the exact temperature limits and required qualification for the end application before substitution.
When should I choose MCP6042-E/SN instead of MCP6002-E/SN?
Choose MCP6042-E/SN when very low operating current and operation from 1.4 V are priorities, because the MCP6042 is specified at 600 nA typical current per amplifier and a 14 kHz gain-bandwidth product. Choose MCP6002-E/SN when its higher bandwidth or output-drive capability is required. Both are dual amplifiers, but the correct choice depends on speed, load, noise, and supply requirements.
What is the best drop-in replacement for MCP6042-E/SN?
MCP6042-I/SN is the closest same-package option because it retains the Microchip MCP6042 dual-amplifier configuration in an 8-pin SOIC while changing the temperature-grade designation. It should be used only after checking temperature limits, electrical ratings, pin functions, and qualification requirements against the original design. MCP6042T-E/SN is electrically similar but changes the assembly packing format.
Is MCP6042-E/SN suitable for sensor signal conditioning?
Yes, MCP6042-E/SN is suitable for low-frequency sensor signal conditioning, particularly when the sensor operates from a low-voltage supply and current consumption is important. Its rail-to-rail input supports signals near the supply rails, while 600 nA typical operating current limits amplifier overhead. Confirm input capacitance, source impedance, output loading, and noise requirements during sensor-interface design.
How should MCP6042-E/SN be bypassed on a PCB?
Place the supply bypass capacitor close to the MCP6042-E/SN supply pin, with a short and low-inductance return path to the ground pin. Follow the manufacturer datasheet's recommended decoupling arrangement and use a quiet ground reference for the analog signal path. Keep feedback resistors and non-inverting inputs away from switching nodes to prevent supply ripple and digital coupling from appearing as input error.
Is MCP6042-E/SN currently available to order?
Current availability and lead time can be requested through the Request a Quote form on this product page. The manufacturer product page and current distributor records identify MCP6042-E/SN as an orderable 8-pin SOIC dual operational amplifier. Quote requests should state the required quantity, date code, lot-control requirements, and destination to establish a current supply commitment.
What is the price of MCP6042-E/SN?
The current commercial terms for MCP6042-E/SN are available through the Request a Quote form on this page. The form allows buyers to specify quantity, packaging preference, target date, and shipment requirements without relying on a static price. Current pricing and lead time should be confirmed for the exact ordering code MCP6042-E/SN before releasing a production order.
What is the lead time for MCP6042-E/SN?
The current lead time for MCP6042-E/SN should be confirmed through the Request a Quote form on this product page. State the required quantity and production schedule when requesting the quotation so the supplier can check available inventory, manufacturing allocation, and delivery options. The 8-pin SOIC ordering suffix should be included in the request to avoid ambiguity with other MCP6042 package formats.
Can MCP6042-E/SN be used as a comparator?
Yes, MCP6042-E/SN can perform low-frequency comparator functions because it has rail-to-rail input and output operation. The 14 kHz gain-bandwidth product and specified output-drive capability must satisfy the propagation-delay and load requirements of the circuit. For applications requiring faster switching, lower offset, or dedicated open-drain output, select a comparator designed for those specifications.

Engineering reference data for MCP6042-E/SN — comparison, design guidance, and compliance information.

Selection Guide

Choose MCP6042-E/SN for low-voltage, low-power analog designs that need two general-purpose amplifiers with 14 kHz bandwidth, rail-to-rail input and output, and operation from 1.4 V. It is particularly appropriate for battery-powered sensors, portable instrumentation, low-frequency filters, current-to-voltage conversion, and modest audio-conditioning stages. Select MCP6042-I/SN when its industrial temperature-grade designation is the better fit, but verify all temperature limits and environmental requirements before changing the approved ordering code. MCP6042T-E/SN offers the same 8-pin SOIC electrical configuration with tape-and-reel shipment, making it useful for automated production rather than a functional redesign. If the circuit requires substantially more bandwidth, faster settling, lower offset, or stronger output drive, move to a higher-performance dual amplifier and re-evaluate stability, power, noise, and layout.

Comparison with Alternatives

Parameter This Product MCP6042-I/SN MCP6042T-E/SN
Brand Microchip Technology Microchip Technology Microchip Technology
Package 8-SOIC 8-SOIC - same 8-SOIC - same
Number of Amplifiers 2 2 2
Temperature-Grade Designation E temperature grade I temperature grade E temperature grade

Key Differentiators

  • Very low operating current supports portable systems (vs MCP6002-E/SN)
  • Single-supply operation extends to low-voltage rails (vs MCP6002-E/SN)
  • Dual rail-to-rail channels in one 8-pin package (vs MCP6042-I/SN)

Design Notes

Place the supply bypass capacitor immediately beside the MCP6042-E/SN supply and ground pins. Use the decoupling arrangement specified in the manufacturer datasheet and keep the loop area small because long supply traces can let switching noise enter a high-gain analog stage. Route sensitive input and feedback nets away from inductors, switching-regulator outputs, relay contacts, and high-current return paths.

Design the feedback network around the 14 kHz gain-bandwidth product rather than assuming unlimited closed-loop bandwidth. Lower closed-loop gains provide more bandwidth and phase margin, while higher gains reduce available bandwidth. Check source impedance because very high-impedance sensors can interact with input bias current and capacitance, and verify the output load against the amplifier's specified source and sink capability.

Calculate the complete system budget from the 600 nA typical operating current per amplifier, not only the load current at the output. Include sensor biasing, pull resistors, leakage, ADC power, and switching-converter losses. The device's less-than-1 µA maximum quiescent current per amplifier helps in battery systems, but it does not remove the need to minimize supply-side losses and board contamination.

Do not substitute the 8-pin SOIC MCP6042 for a single-amplifier or 8-pin MSOP variant without comparing the pin description tables. Rail-to-rail input and output does not guarantee unlimited output-current capability or operation beyond the rated supply range. Confirm the exact suffix, temperature grade, package, pin functions, and production requirements before approving a replacement.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The available product information identifies an E-temperature-grade industrial operational amplifier but does not provide a definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration.

Data verified on: 2026-11-20 — data verified and curated by XAIPART's component engineering team

Related Searches

mcp6042 datasheet mcp6042 datasheet pdf mcp6042 pinout MCP6042-E/SN specifications MCP6042-E/SN equivalent MCP6042-E/SN replacement MCP6042-E/SN cross reference MCP6042-E/SN 8-SOIC MCP6042 dual low power op amp MCP6042-E/SN price MCP6042-E/SN stock Microchip MCP6042-E/SN MCP6042-E/SN sensor amplifier MCP6042 vs MCP6002-E/SN MCP6042 rail-to-rail 14kHz amplifier

Related Components & Terms

Microchip Technology MCP6042-E/SN MCP6042 MCP6042-I/SN MCP6042T-E/SN MCP6002-E/SN MCP6242-E/SN operational amplifier op amp dual amplifier CMOS operational amplifier rail-to-rail input rail-to-rail output gain-bandwidth product quiescent current input offset voltage 8-pin SOIC SOIC package surface-mount package low-power analog sensor conditioning battery-powered electronics active filter transimpedance amplifier
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details