MCP6042-E/SN - Dual 14kHz Low-Power RRIO Op Amp | Microchip
N.º de pieza: MCP6042-E/SN ✓ ActivoMCP6042-E/SN Descripción general
An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and drive signals. The MCP6042 belongs to the CMOS operational-amplifier family within the broader voltage-regulator and power-management IC ecosystem. Its dual-channel configuration provides two amplifiers in one package, reducing board area when a system needs signal conditioning on multiple low-voltage rails.
The MCP6042-E/SN combines a 14 kHz gain-bandwidth product with a typical operating current of 600 nA. According to the Microchip manufacturer product page, input offset voltage is less than 3 mV, while the family operates from a single supply as low as 1.4 V and draws less than 1 µA maximum quiescent current per amplifier. Rail-to-rail input and output stages allow the amplifier to operate close to the supply rails.
The MCP6042 uses Microchip's advanced CMOS technology. This rail-to-rail architecture supports low-voltage battery-powered designs where usable signal range, supply headroom, and current consumption are important. Because its bandwidth is intentionally modest, the device is best suited to low-frequency precision and general-purpose functions rather than high-speed signal conditioning.
Typical uses include battery-powered instrumentation, sensor interfaces, low-frequency active filters, current-to-voltage conversion, comparators, audio input conditioning, and portable measurement systems. The dual topology is particularly useful when two related analog channels must share the same package, supply voltage, and operating-current budget.
Design the surrounding network for the MCP6042's gain-bandwidth and output-current limits, and place input, feedback, and bypass components close to the device to reduce parasitic feedback. Verify the required source and sink current into the output at the selected load because rail-to-rail operation simplifies signal range but does not remove output-drive limitations.
This product page combines manufacturer specifications, sourcing guidance, drop-in replacement analysis, application examples, and practical PCB considerations to support faster engineering decisions beyond the basic datasheet feature list.
Alternativas directas para MCP6042-E/SN — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MCP6042-E/SN (mismo factor de forma y huella) — difiere en Maximum Quiescent Current, Package.
MCP6042-I/SN
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MCP6042T-E/SN
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MCP6042-E/SN Valores máximos y características eléctricas
| Number of Amplifiers | 2 |
| Product Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 14 kHz |
| Typical Operating Current | 600 nA per amplifier |
| Maximum Quiescent Current | <1 µA per amplifier |
| Minimum Single-Supply Voltage | 1.4 V |
| Typical Input Offset Voltage | <3 mV |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Process Technology | Advanced CMOS |
| Encapsulado | 8-pin SOIC, 3.90 mm width |
| Tipo de montaje | Surface mount |
| Operating Temperature Grade | E temperature grade |
Guía de configuración de pines de MCP6042-E/SN 8-pin soic, 3.90 mm width
Configuración de pines para MCP6042-E/SN (encapsulado 8-pin soic, 3.90 mm width). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para MCP6042-E/SN.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MCP6042-E/SN es adecuado para 6 aplicacións: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Low-Level Signal Conditioning, Current-to-Voltage Conversion, Low-Frequency Active Filtering, Audio Input Conditioning.
Battery-Powered Sensor Conditioning
The MCP6042-E/SN fits battery-powered sensor interfaces because each amplifier draws 600 nA typical operating current and the family operates from 1.4 V. Rail-to-rail input and output stages preserve signal range when the sensor output lies near the supply rails. A typical circuit buffers a high-impedance sensor, scales its voltage, and drives the input of a low-power converter or data-capture stage. The main design consideration is bandwidth: the 14 kHz gain-bandwidth product is suitable for slow environmental or biometric signals, but it is not appropriate for fast pulse signals or wideband sensor acquisition.
Recomendado
Portable Medical Monitoring
The MCP6042-E/SN is useful in portable medical monitoring circuits where each channel must operate from limited current and voltage. Its less-than-1 µA maximum quiescent current per amplifier and 600 nA typical operating current reduce amplifier contribution to total system load, while rail-to-rail operation supports low-amplitude signals close to the supply limits. The dual package can condition two related sensor channels in a compact medical device. Engineers should verify medical qualification requirements, input offset, noise, isolation barriers, and patient-safety standards because the amplifier ordering code alone does not establish compliance for the finished instrument.
Recomendado
Industrial Low-Level Signal Conditioning
The MCP6042-E/SN can amplify low-level signals in industrial measurement systems when operating speed and current draw are more important than wide bandwidth. Its less-than-3 mV typical input offset and 14 kHz gain-bandwidth product suit slow pressure, temperature, and position sensing interfaces. The amplifier may provide buffering, gain, or active filtering before a higher-resolution converter. Layout must keep the 8-SOIC away from motor-control and relay-switching circuitry, and the external feedback network must be designed around the 14 kHz bandwidth to avoid unintended oscillation or excessive noise gain.
Recomendado
Current-to-Voltage Conversion
The MCP6042-E/SN is appropriate for low-frequency current-to-voltage conversion in electrochemical, battery-fabrication, and laboratory instrumentation. Its rail-to-rail input allows a small shunt voltage to be amplified without requiring a mid-supply bias, and the dual configuration can handle two current channels where monitoring symmetry matters. The 14 kHz gain-bandwidth product constrains closed-loop bandwidth and settling behavior, so the feedback resistor and compensation capacitor must be calculated for the required measurement rate. Input bias current and offset should also be checked against the shunt impedance to avoid measurement errors.
Recomendado
Low-Frequency Active Filtering
The MCP6042-E/SN can implement first- or second-order active filters for slow analog signals because it provides two amplifiers with a 14 kHz gain-bandwidth product. Rail-to-rail input and output operation makes it useful for filters processing signals near a low supply rail. Component tolerances and the amplifier's finite gain-bandwidth response determine actual cutoff accuracy and phase margin. Test the filter across its intended frequency range, keep the signal path compact, and avoid placing high-gain stages too close to switching regulators or digital clock lines.
Recomendado
Audio Input Conditioning
The MCP6042-E/SN can condition low-level audio or microphone signals when the design prioritizes low supply voltage and low current over wide bandwidth. Rail-to-rail input and output operation improves headroom in single-supply audio paths, while the dual amplifier can support stereo or balanced signal conditioning. The 14 kHz gain-bandwidth product limits useful signal bandwidth and may introduce phase shift near the upper edge of the audio range. Confirm the required audio-band performance, input noise, channel matching, output loading, and coupling-capacitor strategy before using it in a precision audio design.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MCP6042-E/SN — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MCP6042-I/SN | MCP6042T-E/SN |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same |
| Number of Amplifiers | 2 | 2 | 2 |
| Temperature-Grade Designation | E temperature grade | I temperature grade | E temperature grade |
Diferenciadores clave
- Very low operating current supports portable systems (frente a MCP6002-E/SN)
- Single-supply operation extends to low-voltage rails (frente a MCP6002-E/SN)
- Dual rail-to-rail channels in one 8-pin package (frente a MCP6042-I/SN)
Notas de diseño
Place the supply bypass capacitor immediately beside the MCP6042-E/SN supply and ground pins. Use the decoupling arrangement specified in the manufacturer datasheet and keep the loop area small because long supply traces can let switching noise enter a high-gain analog stage. Route sensitive input and feedback nets away from inductors, switching-regulator outputs, relay contacts, and high-current return paths.
Design the feedback network around the 14 kHz gain-bandwidth product rather than assuming unlimited closed-loop bandwidth. Lower closed-loop gains provide more bandwidth and phase margin, while higher gains reduce available bandwidth. Check source impedance because very high-impedance sensors can interact with input bias current and capacitance, and verify the output load against the amplifier's specified source and sink capability.
Calculate the complete system budget from the 600 nA typical operating current per amplifier, not only the load current at the output. Include sensor biasing, pull resistors, leakage, ADC power, and switching-converter losses. The device's less-than-1 µA maximum quiescent current per amplifier helps in battery systems, but it does not remove the need to minimize supply-side losses and board contamination.
Do not substitute the 8-pin SOIC MCP6042 for a single-amplifier or 8-pin MSOP variant without comparing the pin description tables. Rail-to-rail input and output does not guarantee unlimited output-current capability or operation beyond the rated supply range. Confirm the exact suffix, temperature grade, package, pin functions, and production requirements before approving a replacement.
Información de cumplimiento
The available product information identifies an E-temperature-grade industrial operational amplifier but does not provide a definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration.