OPA2650E - Dual 360 MHz Op Amp | Texas Instruments
MPN: OPA2650E ✓ ActiveOPA2650E Overview
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Voltage-feedback operational amplifiers use internal feedback to establish gain and are widely used in the broader amplifier IC and power-management signal-chain hierarchy. The OPA2650E combines wide bandwidth with low power consumption, supporting applications that require fast signal response without the higher power demand of many broadband amplifiers.
The OPA2650E provides 360 MHz unity-gain bandwidth and is unity-gain stable. Its specified low-power operation is approximately 50 mW per channel, while differential gain and phase errors are listed as 0.01% and 0.025 degrees. Low harmonic distortion is specified at 5 MHz. These characteristics make the amplifier useful in wideband buffers, cross-coupled stages, communications equipment, video-signal paths, and instrumentation where dynamic range and gain accuracy are important.
The device uses a bipolar voltage-feedback architecture and is designed for high-frequency signal amplification. Its bandwidth allows closed-loop operation at frequencies substantially below the unity-gain limit when external feedback sets the gain. Designers should account for op-amp stability, feedback resistance, output drive, and parasitic capacitance when operating at high speed. The 8-pin VSSOP footprint also requires careful PCB layout so that feedback loops remain short and supply-return paths preserve signal integrity.
Typical uses include dual-channel video amplification, wideband analog buffering, communications signal conditioning, active filtering, and instrumentation. One amplifier channel can handle a positive-going signal while the second handles a complementary, differential, or unrelated signal, reducing component count in dual-path systems. This integration is valuable when board area and channel-to-channel matching are important.
For the highest bandwidth, place input, feedback, and decoupling components close to the associated pins, and use a low-inductance ground-return structure. Avoid long traces around the amplifier because stray capacitance can alter gain, increase peaking, or impair settling. Confirm output-current, supply-voltage, and load requirements against the manufacturer datasheet before finalizing the bias and feedback network.
This page combines the identified electrical characteristics with package, sourcing, replacement, and design guidance for engineers evaluating the OPA2650E. It also highlights where application-specific verification remains essential, including signal bandwidth, output loading, thermal conditions, and final component tolerances.
Drop-in alternatives for OPA2650E — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesOPA2650E Maximum Ratings & Electrical Characteristics
| Amplifier Type | Dual voltage-feedback operational amplifier |
| Number of Channels | 2 channels |
| Unity-Gain Bandwidth | 360 MHz |
| Power Consumption | 50 mW per channel |
| Settling Time | 0.01% criterion; time not stated |
| Low-Harmonic Distortion Frequency | 5 MHz |
| Differential Gain Error | 0.01% |
| Differential Phase Error | 0.025 degrees |
| Unity-Gain Stability | Unity-gain stable |
| Feedback Topology | Voltage feedback |
| Semiconductor Type | Bipolar operational amplifier |
| Package | 8-pin VSSOP |
| Mounting Type | Surface mount |
| Temperature Grade | Industrial |
OPA2650E 8-pin vssop Pin Configuration Guide
Pin configuration for OPA2650E (8-pin vssop package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for OPA2650E.
Refer to the datasheet for full pin configuration.
Typical Applications
OPA2650E is suitable for 6 applications: Wideband Video Signal Buffering, Communications Signal Conditioning, Instrumentation Signal Conditioning, Active Filtering, Dual-Channel Amplification, Test and Measurement Front Ends.
Wideband Video Signal Buffering
The OPA2650E fits wideband video buffering because its 360 MHz unity-gain bandwidth and unity-gain stability support direct buffering without changing the gain-one signal path. According to the manufacturer datasheet, the amplifier also specifies low harmonic distortion at 5 MHz and a 0.01% settling criterion, which are useful when preserving transition fidelity through source and termination networks. The two channels can buffer complementary video paths or provide independent buffering for related signals. Keep feedback loops short, terminate unused inputs according to the datasheet, and place decoupling capacitors close to the supply pins to limit supply-induced distortion.
Communications Signal Conditioning
OPA2650E is appropriate for communications signal-conditioning stages that require more bandwidth than conventional precision amplifiers but do not require the power of a much larger wideband amplifier. Its 360 MHz unity-gain bandwidth provides useful speed margin, while the specified 0.01% differential gain error and 0.025-degree differential phase error support accurate amplification across matched channels. The approximately 50 mW per-channel power figure is important when scaling to multiple radio or interface paths. PCB design should use controlled impedance routing, short feedback traces, and a quiet ground reference to prevent high-frequency pickup from degrading the processed signal.
Instrumentation Signal Conditioning
The OPA2650E can serve in instrumentation paths where sensor or test signals must be amplified before digitization or further processing. Its 360 MHz unity-gain bandwidth handles fast transients and high-bandwidth measurement channels, while unity-gain stability offers flexibility in both follower and feedback-defined gain configurations. The 0.01% differential gain error and 0.025-degree differential phase error are especially relevant when two channels process related signals and must preserve timing and amplitude relationships. Account for input bias current, offset voltage, and output-current requirements in the complete design, and keep sensitive input routing away from power-return currents.
Active Filtering
OPA2650E fits active high-order filtering where op-amp bandwidth and settling behavior determine the usable frequency range. A 360 MHz unity-gain bandwidth provides considerable headroom above the passband of many moderate-frequency filters, and the 0.01% settling specification is valuable when the filter must reach accurate steady-state levels quickly. The device can implement both inverting and non-inverting sections with conventional voltage-feedback networks. Component tolerances and parasitic capacitance can shift poles and cause peaking, so simulate the complete filter and preserve the recommended feedback topology. Place resistor networks and decoupling components close to the amplifier pins.
Dual-Channel Amplification
OPA2650E reduces board area in systems requiring two wideband amplification channels by integrating both amplifiers in one 8-pin VSSOP package. The dual arrangement is useful for differential front ends, complementary drive paths, matched sensing channels, or two independent gain stages. Its unity-gain-stable design supports follower operation, while external resistors can establish other closed-loop gains. Each channel must be evaluated independently for gain, bandwidth, output swing, and stability. Maintain symmetric routing where channel matching matters, because unequal ground paths or component placement can create timing and gain differences that are separate from the amplifier specifications.
Test and Measurement Front Ends
OPA2650E can be used at the input of oscilloscope buffers, signal analyzers, automated test equipment, and high-speed measurement fixtures where low distortion and fast settling are needed. The 360 MHz unity-gain bandwidth supports probing of faster edge rates than typical general-purpose amplifiers, while the 0.01% settling criterion helps limit the time required to reach a defined accuracy level. Because a measurement front end can magnify noise and reflection errors, use controlled impedance layouts and short connections. Verify input common-mode range, output swing, and load drive against the manufacturer electrical-characteristics table before finalizing the front end.
Engineering reference data for OPA2650E — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Package | 8-pin VSSOP |
| Brand | Texas Instruments |
| Number of Channels | 2 channels |
| Amplifier Type | Voltage-feedback operational amplifier |
| Unity-Gain Bandwidth | 360 MHz |
| Power Consumption | 50 mW per channel |
| Settling Time Criterion | 0.01% criterion; settling time not stated |
| Low-Harmonic Distortion Frequency | 5 MHz |
| Differential Gain Error | 0.01% |
| Differential Phase Error | 0.025 degrees |
Key Differentiators
- High bandwidth in a dual low-power amplifier (vs OPA2650E-2500)
- Direct unity-gain buffer capability (vs OPA2650E-2500)
- Matched wideband dual-channel architecture (vs OPA2650E-2500)
Design Notes
Keep each feedback loop physically short and place its resistor network close to the amplifier pins. The 360 MHz unity-gain bandwidth makes stray PCB capacitance electrically significant, particularly around high-impedance input and feedback nodes. Route each channel independently, use a continuous ground reference near the device, and avoid passing feedback traces over split-plane boundaries. These steps reduce parasitic feedback, gain peaking, and unexpected instability.
Place the supply-bypass capacitor as close as practical to the power pins, with a short and low-inductance return path to the device ground. Verify the required supply voltage, supply sequencing, output swing, and load current against the manufacturer electrical-characteristics table before choosing capacitor voltage ratings. Although the specified power consumption is approximately 50 mW per channel, total system dissipation also depends on supply voltage, load current, package construction, and board thermal resistance.
Do not assume that unity-gain stability guarantees acceptable behavior at every gain and capacitive load. Evaluate the intended feedback network, source impedance, load, and PCB capacitance, especially when driving long cables or sampling edges above the nominal video bandwidth. The manufacturer datasheet should be used to select stable operating conditions and to confirm input and output overdrive behavior. Add small isolation resistance near the output when driving capacitive loads if the application guidance permits it.
Avoid treating the 0.01% settling specification as a complete timing value; the accompanying settling time and test conditions must be read from the manufacturer datasheet. Likewise, confirm that the 5 MHz low-harmonic-distortion statement applies to the intended supply, gain, load, and output-amplitude conditions. These qualifications matter in wideband systems where a nominal bandwidth alone cannot predict waveform fidelity or channel matching.
Compliance Information
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration is present in the identified product information. AEC-Q100 is not applicable because OPA2650E is an industrial-grade analog operational amplifier rather than an automotive-qualified device.