OPA347UA - 5.5V 350kHz RRIO Op Amp | Texas Instruments
MPN: OPA347UA ✓ ActiveOPA347UA Overview
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to set the closed-loop gain. The OPA347 belongs to the operational-amplifier hierarchy within analog signal-chain ICs. Its rail-to-rail input and output capability allows the signal and output ranges to approach the supply rails, which is useful in systems powered from a single low-voltage source.
The OPA347UA's headline characteristics are its 5.5 V supply limit, 350 kHz gain-bandwidth product, and 20 uA quiescent current. The low quiescent current reduces the supply demand of continuously powered circuits, while the 350 kHz bandwidth supports low-frequency filtering, buffering, and gain stages. Its single-amplifier configuration reduces board area compared with a dual or quad device when only one signal path is required.
Texas Instruments describes the OPA347 family as a microPower, low-cost operational-amplifier family offered in several packages. The OPA347UA is the single-amplifier 8-pin SOIC option. Because its bandwidth is modest, the device is most appropriate for slow sensor, instrumentation, and control signals rather than high-speed data acquisition, video, or RF signal chains.
Typical uses include low-power sensor conditioning, buffered transducer interfaces, active filters, battery-powered monitoring, and general-purpose gain stages. The rail-to-rail behavior is especially useful when the signal source can operate near ground or near the positive supply rail. Designers must still confirm common-mode limits, output swing, stability, and noise performance against the exact operating conditions in the manufacturer datasheet.
For PCB design, use short feedback paths, maintain a clean ground reference, and place the bypass capacitor close to the supply pins. Do not assume that every rail-to-rail input stage produces the same distortion, offset, noise, or common-mode behavior. Compare the complete electrical characteristics across temperature when precision is required.
This product page consolidates the verified OPA347UA operating characteristics, package information, sourcing path, design considerations, and application guidance. It also distinguishes confirmed drop-in alternatives from related family members and explicitly identifies parameters that require confirmation against the Texas Instruments datasheet before design release.
Drop-in alternatives for OPA347UA — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesOPA347UA Maximum Ratings & Electrical Characteristics
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 350 kHz |
| Quiescent Current | 20 uA |
| Input Common-Mode Architecture | Rail-to-rail input |
| Output Architecture | Rail-to-rail output |
| Circuit Count | 1 circuit |
| Package Type | 8-pin SOIC |
| Operating Temperature Range | -55 C to +125 C |
OPA347UA 8-pin soic Pin Configuration Guide
Pin configuration for OPA347UA (8-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for OPA347UA.
Refer to the datasheet for full pin configuration.
Typical Applications
OPA347UA is suitable for 6 applications: Low-Power Sensor Signal Conditioning, Battery-Powered Monitoring System, Precision Active Filter, Transducer Interface and Buffering, Portable Medical Sensor Interface, General-Purpose Gain and Buffer Stage.
Low-Power Sensor Signal Conditioning
The OPA347UA fits a low-power sensor front end when the required signal bandwidth remains well below its 350 kHz gain-bandwidth product. Its 20 uA quiescent current helps limit the amplifier's standing contribution in a battery-powered instrument, while rail-to-rail input and output operation gives the circuit useful signal range near the supply rails. Place the device in a non-inverting or inverting amplifier stage and confirm that the source impedance, gain, and noise bandwidth do not create an offset or stability problem. Decoupling close to the supply pins and short feedback traces will help preserve the intended low-noise, low-power behavior.
Recommended
Battery-Powered Monitoring System
OPA347UA is appropriate for a battery-powered monitoring circuit that must remain active while consuming little standby current. Its 20 uA quiescent current is the key power-budget parameter, and the single amplifier in an 8-pin SOIC package leaves additional board area for sensing, processing, and protection circuitry. Rail-to-rail input and output behavior is useful when the monitored signal occupies much of a low-voltage range. Check the common-mode and output-swing limits at the actual supply voltage, especially when operating near the battery's lower voltage, because a rail-to-rail architecture does not guarantee perfectly linear operation at every rail.
Recommended
Precision Active Filter
The OPA347UA can implement a first-order or low-order active filter for slow analog signals because its 350 kHz gain-bandwidth product provides substantial margin above typical low-frequency filter corners. Rail-to-rail input and output operation supports filters operating across much of the available supply range, while the single-amplifier 8-pin SOIC package keeps the footprint compact. Select resistor and capacitor values against the closed-loop gain and the amplifier's stability requirements, then evaluate offset, noise, and component tolerances over the intended temperature range. Keep the feedback network close to the device and provide local supply bypassing to minimize added board noise.
Recommended
Transducer Interface and Buffering
OPA347UA is suitable for buffering a transducer or resistive sensor when the signal bandwidth is low and power consumption is important. The 20 uA quiescent current is useful in portable measurement equipment, and the rail-to-rail input stage allows the amplifier to accept signals closer to ground or the positive rail than a conventional non-rail-to-rail device. The 350 kHz bandwidth is sufficient for many temperature, pressure, and position sensing signals. Designers should still verify input bias current against the sensor's effective source impedance and use the manufacturer input-bias-current data to determine whether a bias-current compensation resistor is needed.
Recommended
Portable Medical Sensor Interface
The OPA347UA can serve as the analog front-end amplifier in a portable medical sensor interface when the required bandwidth is compatible with its 350 kHz gain-bandwidth product. The low 20 uA quiescent current supports a compact, battery-powered instrument, and the single 8-pin SOIC package leaves room for isolation, data conversion, and digital processing stages. Because general-purpose operation does not itself establish medical qualification, confirm the complete electrical characteristics, temperature behavior, and applicable risk requirements for the finished product. Keep sensitive input traces short, provide a stable reference ground, and evaluate offset and noise in the complete sensor chain.
Recommended
General-Purpose Gain and Buffer Stage
OPA347UA works as a general-purpose voltage-gain or unity-gain buffer stage for low-frequency control and instrumentation signals. Its 5.5 V maximum supply supports low-voltage logic-compatible analog systems, and the single amplifier can be configured for common noninverting, inverting, or differential-related buffering arrangements. The 350 kHz bandwidth defines the useful small-signal operating range, while 20 uA quiescent current favors portable equipment. During design, verify output swing at the required load, assess capacitive-load stability, and place the bypass capacitor close to the supply pins. The 8-pin SOIC footprint also simplifies assembly where a through-hole operational-amplifier package would be unnecessarily large.
Recommended
Recommended Products Summary
Engineering reference data for OPA347UA — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Package | 8-pin SOIC |
| Brand | Texas Instruments |
| Amplifier Configuration | Single operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 350 kHz |
| Quiescent Current | 20 uA |
| Input Architecture | Rail-to-rail input |
| Output Architecture | Rail-to-rail output |
| Operating Temperature Range | -55 C to +125 C |
Key Differentiators
- Low quiescent current in an 8-pin SOIC amplifier (vs OPA348AID)
- Single amplifier reduces occupied board area (vs OPA2347)
- Rail-to-rail input and output operation (vs OPA342UA)
- 350 kHz bandwidth is sufficient for slow measurement signals (vs OPA348AID)
Design Notes
Place the supply-bypass capacitor close to the OPA347UA supply pins and connect it directly to the device ground pin. Keep the feedback network and input traces short to reduce parasitic capacitance and susceptibility to board noise. The 8-pin SOIC footprint leaves little room for excess loop area, so route the ground return to the capacitor without passing through a switching node or electrically quiet ground region.
Do not select the OPA347UA solely because it is rail-to-rail. Rail-to-rail input and output architecture does not guarantee perfect linearity at the rails. Check the common-mode range, output swing, input offset, bias current, noise, and stability curves in the manufacturer datasheet for the actual supply voltage, load, source impedance, gain, and temperature.
Estimated: at a 3.3 V supply and 20 uA quiescent current, the amplifier's specified quiescent-current contribution is approximately 66 uW before load current and external-divider bias are included. Use 20 uA and 3.3 V as the inputs to this estimate, then add sensor, divider, and load currents when calculating the complete power budget. Actual consumption also depends on output swing and frequency.
Treat the 350 kHz gain-bandwidth product as the main small-signal bandwidth constraint. A practical closed-loop amplifier should normally operate well below that limit, and additional phase margin is needed for noise-gain compensation. Verify the gain and feedback-network values against the manufacturer's stability guidance, especially when driving capacitive loads or adding an additional pole in the feedback path.
Compliance Information
The available product and distributor information does not explicitly state the requested compliance classifications. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with the manufacturer for the exact OPA347UA ordering code.