Texas Instruments

OPA347UA - 5.5V 350kHz RRIO Op Amp | Texas Instruments

MPN: OPA347UA ✓ Hoạt động
5.5 V Vdss 20 uA Id 8-pin SOIC Package
MOQ: 1 |

OPA347UA Tóm tắt

The Texas Instruments OPA347UA is a single, rail-to-rail input and output operational amplifier with a 5.5 V maximum supply voltage, 350 kHz gain-bandwidth product, and 20 uA low quiescent current in an 8-pin SOIC package. It is designed for low-voltage, low-power signal-conditioning systems where compactness, rail-to-rail operation, and modest bandwidth are more important than high-speed performance.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to set the closed-loop gain. The OPA347 belongs to the operational-amplifier hierarchy within analog signal-chain ICs. Its rail-to-rail input and output capability allows the signal and output ranges to approach the supply rails, which is useful in systems powered from a single low-voltage source.

The OPA347UA's headline characteristics are its 5.5 V supply limit, 350 kHz gain-bandwidth product, and 20 uA quiescent current. The low quiescent current reduces the supply demand of continuously powered circuits, while the 350 kHz bandwidth supports low-frequency filtering, buffering, and gain stages. Its single-amplifier configuration reduces board area compared with a dual or quad device when only one signal path is required.

Texas Instruments describes the OPA347 family as a microPower, low-cost operational-amplifier family offered in several packages. The OPA347UA is the single-amplifier 8-pin SOIC option. Because its bandwidth is modest, the device is most appropriate for slow sensor, instrumentation, and control signals rather than high-speed data acquisition, video, or RF signal chains.

Typical uses include low-power sensor conditioning, buffered transducer interfaces, active filters, battery-powered monitoring, and general-purpose gain stages. The rail-to-rail behavior is especially useful when the signal source can operate near ground or near the positive supply rail. Designers must still confirm common-mode limits, output swing, stability, and noise performance against the exact operating conditions in the manufacturer datasheet.

For PCB design, use short feedback paths, maintain a clean ground reference, and place the bypass capacitor close to the supply pins. Do not assume that every rail-to-rail input stage produces the same distortion, offset, noise, or common-mode behavior. Compare the complete electrical characteristics across temperature when precision is required.

This product page consolidates the verified OPA347UA operating characteristics, package information, sourcing path, design considerations, and application guidance. It also distinguishes confirmed drop-in alternatives from related family members and explicitly identifies parameters that require confirmation against the Texas Instruments datasheet before design release.

Bộ thay thế dễ dàng lắp đặt cho OPA347UA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.

Yêu cầu các bộ thay thế

OPA347UA Tỷ lệ tối đa & tính chất điện

Amplifier Type Single operational amplifier
Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 350 kHz
Điện áp yên tĩnh 20 uA
Input Common-Mode Architecture Rail-to-rail input
Output Architecture Rail-to-rail output
Circuit Count 1 circuit
Package Type 8-pin SOIC
Khoảng nhiệt độ hoạt động -55 C to +125 C

Hướng dẫn cấu hình chân OPA347UA 8-pin soic

Cấu hình chân cho OPA347UA (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 8-pin soic cho OPA347UA

Không có dữ liệu chân cụ thể sẵn có cho OPA347UA.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

OPA347UA phù hợp cho 6 Áp dụngs: Low-Power Sensor Signal Conditioning, Battery-Powered Monitoring System, Precision Active Filter, Transducer Interface and Buffering, Portable Medical Sensor Interface, General-Purpose Gain and Buffer Stage.

🧩

Low-Power Sensor Signal Conditioning

The OPA347UA fits a low-power sensor front end when the required signal bandwidth remains well below its 350 kHz gain-bandwidth product. Its 20 uA quiescent current helps limit the amplifier's standing contribution in a battery-powered instrument, while rail-to-rail input and output operation gives the circuit useful signal range near the supply rails. Place the device in a non-inverting or inverting amplifier stage and confirm that the source impedance, gain, and noise bandwidth do not create an offset or stability problem. Decoupling close to the supply pins and short feedback traces will help preserve the intended low-noise, low-power behavior.

🔋

Battery-Powered Monitoring System

OPA347UA is appropriate for a battery-powered monitoring circuit that must remain active while consuming little standby current. Its 20 uA quiescent current is the key power-budget parameter, and the single amplifier in an 8-pin SOIC package leaves additional board area for sensing, processing, and protection circuitry. Rail-to-rail input and output behavior is useful when the monitored signal occupies much of a low-voltage range. Check the common-mode and output-swing limits at the actual supply voltage, especially when operating near the battery's lower voltage, because a rail-to-rail architecture does not guarantee perfectly linear operation at every rail.

📡

Precision Active Filter

The OPA347UA can implement a first-order or low-order active filter for slow analog signals because its 350 kHz gain-bandwidth product provides substantial margin above typical low-frequency filter corners. Rail-to-rail input and output operation supports filters operating across much of the available supply range, while the single-amplifier 8-pin SOIC package keeps the footprint compact. Select resistor and capacitor values against the closed-loop gain and the amplifier's stability requirements, then evaluate offset, noise, and component tolerances over the intended temperature range. Keep the feedback network close to the device and provide local supply bypassing to minimize added board noise.

🏭

Transducer Interface and Buffering

OPA347UA is suitable for buffering a transducer or resistive sensor when the signal bandwidth is low and power consumption is important. The 20 uA quiescent current is useful in portable measurement equipment, and the rail-to-rail input stage allows the amplifier to accept signals closer to ground or the positive rail than a conventional non-rail-to-rail device. The 350 kHz bandwidth is sufficient for many temperature, pressure, and position sensing signals. Designers should still verify input bias current against the sensor's effective source impedance and use the manufacturer input-bias-current data to determine whether a bias-current compensation resistor is needed.

💊

Portable Medical Sensor Interface

The OPA347UA can serve as the analog front-end amplifier in a portable medical sensor interface when the required bandwidth is compatible with its 350 kHz gain-bandwidth product. The low 20 uA quiescent current supports a compact, battery-powered instrument, and the single 8-pin SOIC package leaves room for isolation, data conversion, and digital processing stages. Because general-purpose operation does not itself establish medical qualification, confirm the complete electrical characteristics, temperature behavior, and applicable risk requirements for the finished product. Keep sensitive input traces short, provide a stable reference ground, and evaluate offset and noise in the complete sensor chain.

🔧

General-Purpose Gain and Buffer Stage

OPA347UA works as a general-purpose voltage-gain or unity-gain buffer stage for low-frequency control and instrumentation signals. Its 5.5 V maximum supply supports low-voltage logic-compatible analog systems, and the single amplifier can be configured for common noninverting, inverting, or differential-related buffering arrangements. The 350 kHz bandwidth defines the useful small-signal operating range, while 20 uA quiescent current favors portable equipment. During design, verify output swing at the required load, assess capacitive-load stability, and place the bypass capacitor close to the supply pins. The 8-pin SOIC footprint also simplifies assembly where a through-hole operational-amplifier package would be unnecessarily large.

Tóm tắt các sản phẩm được đề xuất

OPA347UA Texas Instruments Được sử dụng trong: Low-Power Sensor Signal Conditioning, Battery-Powered Monitoring System, Precision Active Filter, Transducer Interface and Buffering, Portable Medical Sensor Interface, General-Purpose Gain and Buffer Stage OPA347UA/2K5 Related ordering option Được sử dụng trong: Low-Power Sensor Signal Conditioning, Precision Active Filter OPA347UAG4 Related OPA347 family ordering option Được sử dụng trong: Battery-Powered Monitoring System, Portable Medical Sensor Interface OPA342UA Texas Instruments Được sử dụng trong: Transducer Interface and Buffering OPA348AID Related TI single-amplifier comparison candidate Được sử dụng trong: General-Purpose Gain and Buffer Stage
What is the operating voltage of OPA347UA?
The OPA347UA supports a maximum supply voltage of 5.5 V. According to the Texas Instruments OPA347 product page, it is a single, 5.5 V, rail-to-rail operational amplifier intended for low-voltage systems. Confirm the minimum operating voltage and exact supply limits for the selected temperature grade in the manufacturer datasheet before powering the device.
What are the key specifications of OPA347UA that engineers should know?
The OPA347UA combines a 5.5 V maximum supply, 350 kHz gain-bandwidth product, 20 uA quiescent current, and rail-to-rail input and output operation in one 8-pin SOIC. According to the Texas Instruments product page, these characteristics make it a low-power, low-bandwidth amplifier for sensor conditioning, buffering, filtering, and other general-purpose analog signal paths.
Where can I download the OPA347UA datasheet PDF?
The official OPA347UA technical information is available from the Texas Instruments product page linked on this listing. Select the OPA347UA ordering information and open the associated datasheet link to review the complete electrical characteristics, pin configuration, typical performance curves, and package drawings before releasing a design.
Where can I find the OPA347UA pinout?
The OPA347UA uses an 8-pin SOIC package. Use the pin-configuration diagram in the Texas Instruments OPA347 datasheet when assigning the supply, ground, input, and output connections. Do not infer the pin functions from another OPA347 package because the physical pin arrangement can change between SOIC, SOT-23-5, SC-70, and DIP-8 options.
Is OPA347UA suitable for low-power sensor conditioning?
Yes, the OPA347UA is suitable for low-power sensor conditioning when the signal bandwidth is modest. Its 20 uA quiescent current limits standing power demand, while the 350 kHz gain-bandwidth product supports low-frequency buffer and amplification stages. Texas Instruments specifies the OPA347 as a microPower operational amplifier with rail-to-rail input and output operation.
OPA347UA vs OPA348AID - which is better for a slow sensor signal?
The OPA347UA is generally the more relevant choice for a slow, low-power sensor signal when its 350 kHz bandwidth is sufficient. The OPA348AID belongs to a different TI family that appears in a direct comparison result. Because that result does not provide a complete parameter table, verify supply voltage, offset, noise, and stability data before selecting either device.
What is the difference between OPA347UA and OPA347UA/2K5?
OPA347UA and OPA347UA/2K5 identify the same OPA347 single-amplifier family and are both listed as 8-pin SOIC devices. The /2K5 suffix identifies a different ordering or reel presentation rather than a materially different amplifier function. Confirm the exact suffix, packing orientation, and manufacturer ordering code against the Texas Instruments part-details page.
When should I choose OPA347UA over another single low-power amplifier?
Choose the OPA347UA when the circuit requires a single amplifier, rail-to-rail input and output behavior, no more than a 5.5 V supply, and a bandwidth near 350 kHz is sufficient. Its 20 uA quiescent current is useful for continuously powered designs. Choose another amplifier only after comparing offset, bias current, noise, output swing, and stability requirements.
Is OPA347UA suitable for audio or RF applications?
The OPA347UA can be used in low-frequency audio control or instrumentation paths when its 350 kHz gain-bandwidth product is adequate, but it is not a high-bandwidth audio or RF amplifier. Its 20 uA quiescent current favors low-power instrumentation. For wide audio bandwidth, precision low-noise performance, or RF frequencies, use a device explicitly specified for those requirements.
What is the best drop-in replacement for OPA347UA?
No independently verified cross-manufacturer drop-in replacement is identified for the OPA347UA. A valid replacement must match the 8-pin SOIC footprint, pin functions, 5.5 V supply limit, rail-to-rail behavior, and application-critical electrical characteristics. Use the Texas Instruments cross-reference search and the manufacturer pinout table before approving a substitute.
What can replace OPA347UA?
The only confirmed same-device ordering option located for OPA347UA is the related OPA347UA/2K5 presentation, but it does not establish a broader list of qualified replacements. Do not treat it as a different amplifier design. For another manufacturer, require documented pin compatibility and a side-by-side comparison of bandwidth, quiescent current, offset, noise, and output swing.
Is OPA347UA the same as OPA348AID?
No, OPA347UA and OPA348AID are distinct TI part numbers from related amplifier families. The verified comparison page lists both parts but does not establish that they are electrically or pin-for-pin identical. Treat OPA348AID as a separate design candidate and compare its complete datasheet parameters and package pinout with OPA347UA.
What is the best Analog Devices equivalent for OPA347UA?
The available cross-reference results do not identify a verified Analog Devices equivalent for OPA347UA. Because an equivalent must preserve the 8-pin SOIC pinout, 5.5 V maximum supply, rail-to-rail operation, and approximately 350 kHz bandwidth, no model is recommended without a manufacturer-supported comparison. Search by those electrical constraints and then verify the pin assignment and full temperature range.
Where can I buy OPA347UA online?
Use the Request a Quote form on this page to request OPA347UA pricing, availability, and lead time from XAIPART. The official Texas Instruments part-details page also identifies the exact ordering code and links to manufacturer technical information. Provide the required quantity, target reel format, and delivery location in the request.
What is the price and lead time of OPA347UA?
Request the current OPA347UA unit price, stock position, minimum order quantity, and lead time through the Request a Quote form on this page. The component is presented as an orderable catalog part, while live commercial terms can change with quantity and supply conditions. Include your required date and packaging requirements with the request.

Dữ liệu tham khảo kỹ thuật cho OPA347UA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the OPA347UA for a compact, single-channel analog signal path powered by no more than 5.5 V, especially when low quiescent current and rail-to-rail input and output behavior are priorities. Its 20 uA quiescent current supports portable or continuously powered equipment, while 350 kHz bandwidth suits low-frequency sensors, filters, buffers, and control signals. The related OPA347UA/2K5 ordering option can be considered when its reel code and commercial terms meet the assembly requirement, but it is not a different amplifier design. OPA348AID may be appropriate when substantially higher bandwidth is required, although it is not a like-for-like replacement. OPA342UA should be evaluated independently because the available comparison material does not establish full electrical equivalence. For any proposed substitute, verify the 8-pin SOIC pin assignment, supply range, common-mode range, output swing, offset, bias current, noise, stability, and temperature behavior before PCB release.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này
Package 8-pin SOIC
Brand Texas Instruments
Amplifier Configuration Single operational amplifier
Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 350 kHz
Quiescent Current 20 uA
Input Architecture Rail-to-rail input
Output Architecture Rail-to-rail output
Operating Temperature Range -55 C to +125 C

Bảo phân biệt quan trọng

  • Low quiescent current in an 8-pin SOIC amplifier (vsOPA348AID)
  • Single amplifier reduces occupied board area (vsOPA2347)
  • Rail-to-rail input and output operation (vsOPA342UA)
  • 350 kHz bandwidth is sufficient for slow measurement signals (vsOPA348AID)

Ghi chú thiết kế

Place the supply-bypass capacitor close to the OPA347UA supply pins and connect it directly to the device ground pin. Keep the feedback network and input traces short to reduce parasitic capacitance and susceptibility to board noise. The 8-pin SOIC footprint leaves little room for excess loop area, so route the ground return to the capacitor without passing through a switching node or electrically quiet ground region.

Do not select the OPA347UA solely because it is rail-to-rail. Rail-to-rail input and output architecture does not guarantee perfect linearity at the rails. Check the common-mode range, output swing, input offset, bias current, noise, and stability curves in the manufacturer datasheet for the actual supply voltage, load, source impedance, gain, and temperature.

Estimated: at a 3.3 V supply and 20 uA quiescent current, the amplifier's specified quiescent-current contribution is approximately 66 uW before load current and external-divider bias are included. Use 20 uA and 3.3 V as the inputs to this estimate, then add sensor, divider, and load currents when calculating the complete power budget. Actual consumption also depends on output swing and frequency.

Treat the 350 kHz gain-bandwidth product as the main small-signal bandwidth constraint. A practical closed-loop amplifier should normally operate well below that limit, and additional phase margin is needed for noise-gain compensation. Verify the gain and feedback-network values against the manufacturer's stability guidance, especially when driving capacitive loads or adding an additional pole in the feedback path.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The available product and distributor information does not explicitly state the requested compliance classifications. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with the manufacturer for the exact OPA347UA ordering code.

Dữ liệu được xác minh vào: 2026-11-19 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

OPA347UA datasheet OPA347UA pinout OPA347UA datasheet pdf OPA347UA 350kHz amplifier OPA347UA 20uA quiescent current OPA347UA 5.5V rail-to-rail op amp OPA347UA SOIC-8 footprint OPA347UA equivalent OPA347UA replacement OPA347UA cross reference OPA347UA vs OPA348AID OPA347UA vs OPA342UA Texas Instruments OPA347UA OPA347UA price OPA347UA stock

Các bộ phận và thuật ngữ liên quan

Texas Instruments OPA347UA OPA347UA/2K5 OPA347UAG4 OPA348AID OPA342UA OPA2347 OPA4347 operational amplifier single amplifier microPower operational amplifier rail-to-rail input rail-to-rail output analog integrated circuit signal-conditioning IC low-power amplifier gain-bandwidth product quiescent current common-mode range input offset voltage input bias current 8-pin SOIC SOIC package family surface-mount package sensor conditioning active filter battery-powered monitoring
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ