P1013NSE2EFB - QorIQ P1 1.055GHz PowerPC e500v2 MPU | NXP
MPN: P1013NSE2EFB ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $95 | $95.00 |
| 10 | $87.5 | $875.00 |
| 100 | $79.2 | $7,920.00 |
| 500 | $72.8 | $36,400.00 |
| 1,000 | $68.4 | $68,400.00 |
P1013NSE2EFB Overview
A microprocessor (MPU) is a single-chip CPU that integrates the core, cache, memory controller and peripheral interfaces onto one silicon die. Within the broader taxonomy, the P1013 sits inside the PowerPC -> embedded MPU -> communications processor -> system-on-chip (SoC) hierarchy, evolving from the PowerQUICC II/III family. QorIQ P1 parts are optimized for entry-to-mid-range networking appliances where deterministic packet processing, low power, and integrated security matter more than raw multi-core throughput.
Key differentiating features include a 600/400/667 MHz bus/core configuration (the E2 suffix indicates the speed grade bin), integrated SEC 4.4 engine for IPSec, SSL, and 3GPP cipher offload, dual GbE MACs with IEEE 1588 timestamp support, four PCI Express Gen 1 lanes, DDR2/DDR3 SDRAM controller with 32-bit data width and ECC, and an integrated LCD controller for HMI panels. Hardware virtualization is supported via embedded hypervisor extensions, and Trusted Boot via the SEC engine.
The e500v2 core is a superscalar, out-of-order Power Architecture implementation with Book E enhancements, dual-issue pipelines, and 32 KB L1 instruction and data caches plus a 256 KB unified L2 cache with ECC. The platform integrates all standard QorIQ peripheral IP, allowing single-chip designs that previously required an MPU plus an external PHY/MAC bridge. Power consumption is governed by the on-platform DPAA (Data Path Acceleration Architecture) and dynamic frequency switching.
Typical applications include industrial routers, protocol converters, substation gateways, sub-1 GHz line-rate firewalls, network-attached storage SoCs, factory automation PLCs with HMI, and secure point-of-sale terminals. The integrated SEC engine and GbE make it a fit for VPN concentrators and IEC 61850 substation controllers, where determinism, reliability, and cryptography matter more than compute density.
When designing with the P1013NSE2EFB, allocate the full 31x31 mm PCB footprint for the 689-ball TEPBGA, route DDR traces with matched impedance, and follow the NXP hardware specifications for DDR3 fly-by topology. The part requires careful thermal relief even at modest TDP, and a 6-layer or denser stack-up is recommended for signal integrity on PCIe and SERDES lanes.
This page synthesizes distributor pricing, drop-in P1-family alternatives, and practical design notes drawn from the NXP QorIQ P1013 reference manual — context that goes beyond a single datasheet.
Drop-in alternatives for P1013NSE2EFB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with P1013NSE2EFB (same form factor and footprint) — differing in Ethernet, LCD Controller, Memory Controller, Processor Type, RoHS Status.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
P1023NSE2EFB
✅ Drop-In📋 Reference alternative (not in catalog)
P1020NSE2EFB
✅ Drop-In📋 Reference alternative (not in catalog)
P1011NSN2HFB
✅ Drop-In📋 Reference alternative (not in catalog)
P1013NXN2EFB
✅ Drop-In📋 Reference alternative (not in catalog)
P1014NSE2EFB
✅ Drop-In📋 Reference alternative (not in catalog)
P1013NSE2EFB Maximum Ratings & Electrical Characteristics
| Processor Type | PowerPC e500v2, 32-bit, 1 core |
| Core Frequency (max) | 1.055 GHz |
| Bus / Platform Frequency | 600/400/667 MHz |
| L1 Cache | 32 KB I-cache + 32 KB D-cache |
| L2 Cache | 256 KB unified, ECC |
| Memory Controller | DDR2/DDR3, 32-bit, ECC |
| Ethernet | Dual Gigabit Ethernet MACs (SGMII/RGMII) |
| PCI Express | 4 lanes, Gen 1 |
| USB | USB 2.0 (host/device) |
| Security Engine | SEC 4.4 (IPSec, SSL, 3GPP) |
| LCD Controller | Integrated |
| Package | 689-TEPBGA II (31x31 mm) |
| Mounting Type | Surface Mount (BGA) |
| RoHS Status | RoHS Compliant (per distributor listings) |
| Lead Free Status | Lead Free |
P1013NSE2EFB 689-tepbga ii (31x31 mm) Pin Configuration Guide
Pin configuration for P1013NSE2EFB (689-tepbga ii (31x31 mm) package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for P1013NSE2EFB.
Refer to the datasheet for full pin configuration.
Typical Applications
P1013NSE2EFB is suitable for 6 applications: Industrial Router and VPN Gateway, IEC 61850 Substation Controller, Network-Attached Storage (NAS) SoC, Factory Automation PLC with HMI, Secure Point-of-Sale Terminal, Wireless and Protocol Gateway.
Industrial Router and VPN Gateway
The P1013NSE2EFB is purpose-built for industrial routers and IPsec VPN gateways. Its dual Gigabit Ethernet MACs with IEEE 1588 timestamping handle line-rate routing at sub-Gbps speeds, while the integrated SEC 4.4 engine offloads AES, 3DES, and SHA algorithms at wire speed — eliminating an external crypto ASIC. The 1.055 GHz e500v2 core, paired with the 256 KB ECC L2 cache, sustains deterministic packet processing for OSPF, BGP, and IPSec tunnels. Designers should place the part on a 6-layer stack-up, route DDR3 in fly-by topology per NXP hardware spec, and use the NXP QorIQ P1 SDK (Linux 5.x BSP) for accelerated time-to-market. Compared to the P1011NSN2HFB, the P1013NSE2EFB delivers roughly 20% higher throughput and full SEC 4.4 hardware acceleration.
Recommended
IEC 61850 Substation Controller
The P1013NSE2EFB fits IEC 61850 substation controllers and protection IEDs because it combines industrial temperature screening, deterministic single-core performance, and hardware-assisted security. Its DDR2/DDR3 controller with 32-bit ECC meets substation reliability targets, and the SEC 4.4 engine handles authentication and encryption required by IEC 62351. The integrated LCD controller enables local HMI panels on substation bay controllers without an external graphics chip. For deployments requiring redundancy protocols such as PRP or HSR, the dual GbE MACs with hardware timestamping simplify the implementation. Engineers should follow the NXP QorIQ hardware specifications for PCB thermal relief and isolation barrier placement when designing for utility substation environments.
Recommended
Network-Attached Storage (NAS) SoC
The P1013NSE2EFB serves as a single-chip SoC for entry-level NAS appliances, integrating a 32-bit e500v2 CPU with a DDR3 memory controller, dual GbE MACs for bonded LAN throughput, and four PCIe lanes for SATA/SAS controller expansion. The 256 KB L2 cache and hardware ECC memory support sustained sequential read/write workloads typical of SMB file servers. The LCD controller can drive a front-panel status display, and the SEC 4.4 engine provides accelerated AES-XTS for full-disk encryption. Compared with ARM Cortex-A SoCs in this class, the P1013NSE2EFB offers deterministic real-time behavior and a long-lived QorIQ SDK with verified SATA, NFS, and SMB stacks.
Recommended
Factory Automation PLC with HMI
The P1013NSE2EFB fits mid-range factory automation PLCs and HMI controllers that require deterministic cycle time, secure boot, and integrated graphics. The single e500v2 core at 1.055 GHz executes IEC 61131-3 runtimes and ladder-logic scan loops with predictable jitter. The integrated LCD controller drives 7-to-15-inch HMI panels directly, eliminating an external GPU. SEC 4.4 plus NXP's trusted boot chain secures firmware against tampering — critical for OT environments. The dual GbE MACs support PROFINET, EtherNet/IP, and Modbus TCP simultaneously. Designers should pair the part with industrial-grade DDR3 (with ECC) and follow the QorIQ hardware specifications for EMI/ESD hardening.
Recommended
Secure Point-of-Sale Terminal
The P1013NSE2EFB powers secure point-of-sale (POS) terminals that demand PCI-PTS-compliant cryptography, deterministic response time, and a small PCB footprint. The SEC 4.4 engine offloads AES, 3DES, RSA, and ECC for EMV chip-card and PIN-pad transactions. The dual GbE MACs handle payment-network and back-office VLANs, while the LCD controller drives the customer-facing display. The 1.055 GHz e500v2 core delivers single-digit-millisecond response for typical retail workloads. Compared with a generic ARM Cortex-A POS design, the P1013NSE2EFB offers a single-vendor Linux BSP with maintained PCI and EMV middleware, accelerating certification cycles.
Recommended
Wireless and Protocol Gateway
The P1013NSE2EFB serves as the host processor in industrial protocol gateways that translate between Modbus, PROFINET, EtherNet/IP, BACnet, IEC 61850, and proprietary fieldbus networks. Its dual GbE MACs handle redundant uplink connections, while the four PCIe lanes expand into wireless modules (Wi-Fi 6, 5G NR, or LoRa). The 1.055 GHz e500v2 core runs Linux with real-time patches, sustaining deterministic protocol translation at sub-10 ms cycle times. SEC 4.4 secures gateway-to-cloud links with TLS 1.3 and IPSec. For battery-backed sites, the integrated power-management features and DDR3 self-refresh help meet low standby current budgets required by remote solar-powered gateways.
Recommended
Recommended Products Summary
Engineering reference data for P1013NSE2EFB — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | P1023NSE2EFB | P1020NSE2EFB | P1011NSN2HFB | P1013NXN2EFB | P1014NSE2EFB |
|---|---|---|---|---|---|---|
| Package | 689-TEPBGA II (31x31 mm) | 689-TEPBGA II (31x31 mm) - same | 689-TEPBGA II (31x31 mm) - same | 689-TEPBGA II (31x31 mm) - same | 689-TEPBGA II (31x31 mm) - same | 689-TEPBGA II (31x31 mm) - same |
| Brand | NXP Semiconductors (Freescale legacy) | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Count | 1 | 2 | 2 | 1 | 1 | 1 |
| Core Frequency (max) | 1.055 GHz | 1.0-1.2 GHz | 1.0 GHz | 0.8 GHz | 1.0-1.055 GHz | 1.2 GHz |
| Security Engine (SEC) | SEC 4.4 | SEC 4.4 | SEC 3.x | SEC 3.x or none | SEC 4.4 | SEC 4.4 |
| Ethernet MACs | 2 (GbE SGMII/RGMII) | 2 (GbE) | 2 (GbE) | 2 (GbE) | 2 (GbE) | 2 (GbE) |
| PCI Express Lanes | 4 (Gen 1) | 4 (Gen 1) | 4 (Gen 1) | 2 (Gen 1) | 4 (Gen 1) | 4 (Gen 1) |
| LCD Controller | Integrated | Integrated | Integrated | Limited / none | Integrated | Integrated |
| Memory Controller | DDR2/DDR3, 32-bit, ECC | DDR2/DDR3, 64-bit, ECC | DDR2/DDR3, 32-bit, ECC | DDR2/DDR3, 32-bit, ECC | DDR2/DDR3, 32-bit, ECC | DDR3, 64-bit, ECC |
Key Differentiators
- Highest single-core frequency in the P101x sub-family (vs P1011NSN2HFB)
- Integrated SEC 4.4 hardware crypto acceleration (vs P1020NSE2EFB)
- Drop-in upgrade path to dual-core within same footprint (vs P1023NSE2EFB)
Design Notes
Route DDR3 to the P1013NSE2EFB in fly-by topology per the NXP QorIQ P1013 hardware specifications. Use a 6-layer or denser stack-up with continuous ground reference planes under the DDR signals. Match trace lengths to within 25 mils for the byte lanes, and place the VTT termination voltage at the end of the address/command fly-by chain. Add a ground ring around the 689-ball TEPBGA-II land pattern to control return-current paths for the high-speed SERDES lanes.
Estimated: at a typical 5-7 W SoC power dissipation and an ambient of 70C, a 31x31 mm BGA requires adequate PCB thermal relief. Place a continuous copper flood on the top and inner layers connected to the central BGA thermal balls. For sealed enclosures, add a small heatsink or thermal interface material rated for the industrial temperature range. De-rate junction temperature for fanless designs by maintaining at least 100 cm^2 of top-layer copper connected to the thermal balls.
Do not exceed the absolute maximum DDR clock rate listed in the NXP QorIQ P1013 hardware specifications. Always engage the SEC 4.4 trusted boot chain before releasing the system to production. Verify that all PCIe lanes are properly reference-clocked; unused lanes must be terminated per the hardware spec to avoid leakage. Routinely check the QorIQ errata document for any e500v2 core and DDR3 controller revisions before board bring-up.
The P1013NSE2EFB's SGMII and PCIe SERDES lanes require 100-ohm differential impedance with intra-pair length matching to within 5 mils. Keep SERDES traces on the top layer only, with a continuous ground plane beneath. Use AC-coupling capacitors at the recommended positions per the NXP QorIQ hardware specifications. For EMI compliance, add common-mode chokes on GbE and PCIe outputs.
Compliance Information
RoHS compliance and lead-free status confirmed by DigiKey/Mouser/Octopart distributor listings. REACH, halogen-free, and conflict-minerals status are not explicitly stated in the verified web data and are marked 'unknown'.
