PIC10F222-E/OT - 8-Bit 8MHz Flash MCU | Microchip Technology
MPN: PIC10F222-E/OT ✓ ActivePIC10F222-E/OT Overview
A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The PIC10F222 belongs to the PIC10F family and uses a compact RISC instruction set containing 33 single-word instructions. Most instructions execute in one cycle, while program branches require two cycles, allowing small programs to run with predictable timing in battery-powered and embedded products.
The PIC10F222-E/OT combines 512 program words of 12-bit instruction storage with 23 bytes of data memory. Its four I/O lines support digital control and input functions, while the integrated 8-bit analog-to-digital converter enables the device to measure analog inputs without requiring a separate ADC. A 6-pin SOT-23 package makes the device suitable for space-constrained assemblies where a larger controller is unnecessary.
The PIC10F222-E/OT is built around a fully static CMOS design, allowing processing to continue in low-power operating states. The manufacturer describes 12-bit-wide instructions as highly symmetrical, providing approximately 2:1 code compression compared with conventional 8-bit microcontrollers in the same class. This efficiency helps reduce program-memory requirements for compact control routines.
Typical uses include simple timers, push-button interfaces, LED indicators, battery-powered monitors, analog sensing nodes, and small embedded controllers. Its low pin count simplifies PCB layout, while the ADC allows product designers to combine sensing and control in one device. The extended-temperature ordering option is suited to industrial environments requiring operation from -40°C to +125°C.
When laying out a design, assign each I/O pin to its required external function and keep the analog input connection short to minimize noise pickup. Confirm the oscillator, reset configuration, programming method, and decoupling requirements against the manufacturer datasheet. This page also organizes package information, practical application guidance, direct comparison points, and documented drop-in alternatives for engineering evaluation.
Drop-in alternatives for PIC10F222-E/OT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with PIC10F222-E/OT (same form factor and footprint) — differing in Instruction Set, Package, Operating Temperature Range, Architecture, Program Memory.
PIC10F222T-I/OT
✅ Drop-InContact for price
View Datasheet →PIC10F222-I/OT
✅ Drop-InContact for price
View Datasheet →PIC10F322T-E/OT
✅ Drop-In📋 Reference alternative (not in catalog)
PIC10F322T-I/OT
✅ Drop-In📋 Reference alternative (not in catalog)
PIC10F222-E/OT Maximum Ratings & Electrical Characteristics
| Device Type | 8-bit fully static Flash-based CMOS microcontroller |
| Maximum Clock Frequency | 8 MHz |
| Program Memory | 768 bytes (512 x 12 bits) |
| Data Memory | 23 bytes |
| Number of I/O Lines | 4 lines |
| Architecture | RISC |
| Instruction Count | 33 single-word instructions |
| Typical Instruction Cycle | 1 µs |
| Program Branch Cycle | 2 cycles |
| Instruction Width | 12 bits |
| Code Compression | Typically 2:1 |
| ADC Resolution | 8 bits |
| ADC Quantity | 1 |
| Operating Temperature Range | -40°C to +125°C |
| Package | SOT-23-6 |
| Mounting Type | Surface mount |
| Program Memory Type | Flash |
| Processor Type | 8-bit |
PIC10F222-E/OT sot-23-6 Pin Configuration Guide
Pin configuration for PIC10F222-E/OT (sot-23-6 package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for PIC10F222-E/OT.
Refer to the datasheet for full pin configuration.
Typical Applications
PIC10F222-E/OT is suitable for 6 applications: Battery-Powered Sensor Nodes, Industrial Switch and Button Interfaces, LED Status and Warning Indicators, Analog Control and Threshold Modules, Small Motor and Actuator Controllers, Portable Measurement and Metering Devices.
Battery-Powered Sensor Nodes
The PIC10F222-E/OT fits compact battery-powered sensing nodes because it combines an 8-bit ADC, 23 bytes of RAM, four I/O lines, and fully static CMOS operation in a 6-pin SOT-23-6 package. The ADC can acquire an analog sensor signal while the microcontroller performs thresholding, filtering, and state updates without a separate data converter. Its 8 MHz clock also supports short control routines and timed sampling. Because the device has only 512 program words, firmware should focus on acquisition, calibration, and status reporting rather than complex protocol stacks.
Recommended
Industrial Switch and Button Interfaces
The PIC10F222-E/OT is suitable for small industrial control panels that need debounced inputs, indicator control, and a compact controller footprint. Its four I/O lines can monitor switches and drive simple outputs, while the integrated 8-bit ADC can support an analog control or status input. The -40°C to +125°C operating range suits equipment deployed across industrial temperature conditions. Firmware should include debounce timing, contact-state filtering, fault counters, and a defined output state for startup or fault conditions.
Recommended
LED Status and Warning Indicators
The PIC10F222-E/OT can implement compact LED status, warning, or acknowledgment panels where several indicators and a simple input are required. Its 23 bytes of RAM and 768 bytes of Flash are adequate for animation tables, blink patterns, countdown timers, and switch acknowledgment routines. The four I/O lines reduce component count compared with a larger controller, and the SOT-23-6 package simplifies dense panel layouts. Designers should size current-limiting resistors from the MCU output characteristics and the LED forward voltage rather than assuming all indicators can be driven simultaneously.
Recommended
Analog Control and Threshold Modules
The PIC10F222-E/OT works well in small analog control modules where one sensor level must be converted into a digital decision. The 8-bit ADC handles coarse measurements, while the microcontroller applies thresholds, hysteresis, and timing before controlling an output. Its RISC core executes most instructions in one cycle at 8 MHz, allowing responsive control without a larger processor. For accuracy-critical designs, verify ADC reference tolerances, input acquisition time, source impedance, and output-drive limits in the manufacturer data sheet, and add filtering when the sensor signal changes rapidly.
Recommended
Small Motor and Actuator Controllers
The PIC10F222-E/OT can control a simple actuator, relay, or low-current motor stage where the application needs only a few inputs and outputs. The MCU can store motion sequences, impose timing limits, detect a switch input, and provide a fail-safe output state after reset. Its 8 MHz processing rate provides enough throughput for basic position or duty-cycle management, while the 6-pin package keeps the controller compact. An appropriate transistor or driver stage is required for loads beyond the microcontroller's output capability, and inductive loads need suitable suppression and grounding.
Recommended
Portable Measurement and Metering Devices
The PIC10F222-E/OT supports compact metering products that measure one analog quantity, apply calibration, and report a result through a simple display or output. The integrated 8-bit ADC avoids a separate converter, while 23 bytes of RAM and 512 program words support lightweight filtering and conversion routines. Its SOT-23-6 package is useful in handheld instruments and fixed meters with limited board space. For precision measurement, evaluate the ADS1262IPW when higher-resolution conversion is required; otherwise follow the PIC10F222 ADC timing and reference-layout recommendations.
Recommended
Recommended Products Summary
Engineering reference data for PIC10F222-E/OT — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | PIC10F222T-I/OT | PIC10F222-I/OT | PIC10F322T-E/OT | PIC10F322T-I/OT |
|---|---|---|---|---|---|
| Package | SOT-23-6 | SOT-23-6 | SOT-23-6 | SOT-23-6 | SOT-23-6 |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Processor Architecture | 8-bit RISC | 8-bit RISC | 8-bit RISC | 8-bit PIC10F family | 8-bit PIC10F family |
| Operating Temperature Range | -40°C to +125°C | I-grade designation; confirm numeric range | I-grade designation; confirm numeric range | E-grade designation; confirm numeric range | I-grade designation; confirm numeric range |
| Programming Memory Type | Flash | Flash | Flash | Flash | Flash |
Key Differentiators
- Combines an ADC and four I/O lines in a 6-pin package (vs ATTINY13A-SUR)
- Compact Flash-based control with 12-bit instructions (vs ATTINY20-MMHR)
- SOT-23-6 footprint-compatible family options (vs PIC10F222-I/OT)
Design Notes
Use the SOT-23-6 land pattern and pin-1 orientation specified by the manufacturer, then confirm pad dimensions against the PCB assembly process. Place the device close to its local decoupling capacitor and keep the connection path short. With only six pins, a layout error can easily affect power, programming, reset, or an analog function simultaneously; perform a pin-by-pin schematic and footprint review before release.
Route the analog input directly to its assigned device pin and keep it away from switching nodes, clock edges, and high-current return paths. The 8-bit ADC is appropriate for coarse measurements, but accuracy also depends on source impedance, acquisition time, reference stability, and input filtering. Follow the ADC application information in the Microchip data sheet and include calibration only after characterizing offset and gain across the intended operating range.
Budget the device supply for both active and low-power operating states rather than relying on the maximum clock rate alone. A battery design should account for ADC sampling energy, sensor load, indicator drive, and leakage during storage. Define a safe output state for every externally controlled pin so the board remains predictable during reset, brownout, programming, and firmware faults.
Do not assume that SOT-23-6 compatibility alone guarantees interchangeable behavior across PIC10F222 and PIC10F322 variants. Program memory, RAM, oscillator options, peripheral assignments, and interrupt behavior can differ even when the package and pin count match. For every substitution, compare the manufacturer ordering information, pin descriptions, electrical limits, programming configuration, and generated firmware requirements.
Compliance Information
No explicit compliance certification for the exact ordering code was identified. AEC-Q100 is not applicable because this is not an automotive-qualified ordering variant.