Texas Instruments

SN74LS442N - 4-Bit 3-State Bus Transceiver | Texas Instruments

MPN: SN74LS442N ✓ Active
20-pin PDIP Package
MOQ: 1 |

SN74LS442N Overview

Texas Instruments SN74LS442N is a quadruple tridirectional bus transceiver packaged in a 20-pin PDIP. The device combines four 4-bit transceiver channels in one package, provides non-inverting signal transfer, and places each bus output in a high-impedance state when its direction control is inactive. This combination makes the SN74LS442N suitable for bidirectional parallel-bus interfaces where connected devices must exchange data while maintaining a shared data path.

A bus transceiver is a digital interface component that connects two logic sections through a shared bidirectional line. It belongs to the broader transceiver hierarchy: parallel bus transceiver, bidirectional transceiver, bus-interface IC, and digital logic IC. Unlike a unidirectional buffer, a tridirectional transceiver can support both data transmission and reception. Its 3-state output allows the output driver to disconnect electrically from the bus, preventing multiple connected devices from driving the same node simultaneously.

The SN74LS442N organizes four independent 4-bit channels into one 20-pin PDIP package. Each 4-bit section provides parallel data transfer, while the tridirectional architecture supports communication in either direction. The non-inverting implementation preserves the logical relationship between bus data and the corresponding transceiver-side signals. Three-state operation is particularly important for shared buses because it permits an inactive channel to avoid loading the common node.

The SN74LS442N belongs to the 74LS low-power Schottky TTL logic family. This family is used in systems that require conventional bipolar TTL-compatible interfacing rather than a modern low-voltage differential bus such as LVDS. Because the SN74LS442N operates as a parallel logic device, board-level design must account for shared-bus contention, direction-control sequencing, adequate signal settling time, and correct handling of every enable and direction input.

Typical uses include bidirectional data buffers, computer peripheral interfaces, bus isolation points, test equipment, and legacy industrial control systems. The device can sit between two bus segments when data must be exchanged in both directions without continuously loading either segment. It is also suitable for systems that require a defined high-impedance state during reset, test, or bus ownership changes. The 20-pin PDIP format favors through-hole assembly, repair, and legacy control-system maintenance.

For a reliable design, define the ownership of every bus segment so that only one enabled driver sources a given bit at a time. Direction and enable signals should be decoded cleanly and should not leave two transceivers driving simultaneously during transitions. Review signal timing and bus loading against the circuit requirements, and use the manufacturer's pin-description table when assigning PCB tracks. The PDIP footprint also requires adequate board spacing and appropriate lead-forming during insertion.

This page combines the device's exact catalog identity, package information, application guidance, qualified same-footprint alternatives, and design-oriented cautions. It focuses on the practical role of four non-inverting 4-bit channels and tri-state bus isolation while directing engineers to the manufacturer datasheet for authoritative electrical limits and timing conditions.

Drop-in alternatives for SN74LS442N — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

74LS442N

✅ Drop-In
📦 20-pin PDIP
Same 74LS442 four-channel 4-bit tridirectional function and 20-pin PDIP format; manufacturer sourcing differs by 0 V functional specification

📋 Reference alternative (not in catalog)

DM74LS442N

✅ Drop-In
📦 20-pin PDIP
Same 74LS442 transceiver function and 20-pin PDIP footprint; manufacturer-specific electrical limits must be matched

📋 Reference alternative (not in catalog)

MC74LS442

✅ Drop-In
📦 20-pin PDIP
Same 74LS442 family bus-transceiver role and 20-pin PDIP format; legacy manufacturer and timing differences require review

📋 Reference alternative (not in catalog)

HD74LS442P

✅ Drop-In
📦 20-pin PDIP
Same four-channel 4-bit tridirectional bus function in a 20-pin PDIP package; device-specific timing must be compared

📋 Reference alternative (not in catalog)

TC74LS442

✅ Drop-In
📦 20-pin PDIP
Same 74LS442 quadruple bus-transceiver function and 20-pin PDIP footprint; manufacturer-specific operating limits differ

📋 Reference alternative (not in catalog)

SN74LS442N Specifications

Product Type Quadruple 4-bit bidirectional bus transceiver
Number of Elements 1 element
Bits per Element 4 bits per element
Channel Direction Non-inverting, tridirectional
Output State 3-state output
Number of Bus Channels 4 channels
Total Parallel Data Width 16 bits per device
Package 20-pin PDIP
Pin Count 20 pins
Mounting Type Through-hole
Logic Family 74LS low-power Schottky TTL

SN74LS442N 20-pin pdip Pin Configuration Guide

Pin configuration for SN74LS442N (20-pin pdip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

20-pin pdip package pinout diagram for SN74LS442N

No detailed pinout data available for SN74LS442N.

Refer to the datasheet for full pin configuration.

Typical Applications

SN74LS442N is suitable for 6 applications: Bidirectional Parallel Data Buffer, Legacy Peripheral Bus Isolation, Computer Backplane Interconnect, Industrial Test Equipment Interface, Data Acquisition Module Backplane, Embedded Control System Bus Hub.

🔧

Bidirectional Parallel Data Buffer

The SN74LS442N fits legacy parallel systems that need data to move in either direction across a shared bus. Four 4-bit channels provide 16 parallel bits per device, while the 3-state outputs allow an inactive driver to disconnect from the node. Placing the transceiver between two bus segments can reduce contention and create a controlled interface point. The design must ensure that only one side drives a segment during any given interval. Direction decoding should include non-overlapping transitions so that neither side sources the bus while the other changes direction. Because this is a 20-pin PDIP device, it is especially suitable for repair-oriented and through-hole legacy equipment rather than compact surface-mount systems.

🏭

Legacy Peripheral Bus Isolation

The SN74LS442N can isolate a legacy peripheral bus from the logic that controls bus ownership. Its four non-inverting 4-bit channels support 16 bits of bidirectional signaling, and the tri-state function keeps an unused driver electrically disconnected from the shared line. This arrangement is useful when a peripheral must be selected, disabled, or tested without continuously loading the processor-side bus. Firmware and hardware timing must ensure that enable and direction changes never create a period in which two enabled outputs contend. The through-hole PDIP package supports board-level repair and clear mechanical inspection in older industrial and instrumentation systems.

🖥️

Computer Backplane Interconnect

The SN74LS442N is applicable to legacy computer backplanes where a shared parallel bus must exchange data between two modules. Its four 4-bit sections provide grouped bidirectional channels, and each output can enter a high-impedance state when that channel is not enabled. This characteristic helps preserve signal integrity by preventing an idle transceiver from loading the bus. The design should assign ownership deterministically and account for propagation delay during direction handoff. The 20-pin PDIP format suits large-format control, test, and industrial computers where through-hole components and serviceability remain priorities.

🔧

Industrial Test Equipment Interface

The SN74LS442N can connect a legacy test fixture to a controller while allowing the bus driver to disconnect during idle or measurement intervals. Its four 4-bit tridirectional channels provide a practical way to exchange multiple parallel status and command bits. The 3-state outputs help the fixture avoid loading circuitry that drives the same bus elsewhere. A robust implementation should disable transceivers before changing direction and use the manufacturer timing information to establish safe setup and hold margins. The PDIP package is mechanically convenient for instrument chassis and repairable production-test platforms.

📡

Data Acquisition Module Backplane

The SN74LS442N can be used in legacy data-acquisition modules that require a compact bidirectional parallel interface between a controller and an analog or digital front end. Four grouped 4-bit channels provide 16 lines for command, address, or multiplexed data, and tri-state operation permits the module to release shared lines when not selected. The design should keep analog-signal routing separate from the digital bus and use controlled enables to prevent contention. Its 20-pin PDIP package is well suited to modular backplanes where long service life and straightforward replacement are more important than minimum board area.

⚙️

Embedded Control System Bus Hub

The SN74LS442N can serve as a controlled hub in a legacy embedded system where two subsystems exchange commands over one parallel bus. The non-inverting 4-bit channels preserve bus logic while the tri-state outputs let a nonselected subsystem remain passive. This arrangement can simplify ownership compared with continuously enabled drivers, provided the controller asserts enable and direction signals in a non-overlapping sequence. Because the package is a 20-pin PDIP, the device is most attractive in control boards designed around through-hole logic and maintainable bus architecture rather than high-density mixed-signal products.

What is the SN74LS442N?
The SN74LS442N is a Texas Instruments quadruple tridirectional bus transceiver with four 4-bit channels, non-inverting data transfer, 3-state outputs, and a 20-pin PDIP package. According to the Texas Instruments datasheet listing, the device is designed to support parallel bidirectional bus communication while allowing an inactive output driver to assume a high-impedance state.
How many bus channels and data bits does the SN74LS442N contain?
The SN74LS442N contains four 4-bit transceiver channels, providing 16 parallel bus bits in one package. Texas Instruments describes it as a quadruple tridirectional bus transceiver, while distributor technical data identifies one element with four bits per element and a 3-state output. Each channel can therefore support parallel bidirectional signaling with independently controlled tri-state behavior.
What package does the SN74LS442N use?
The SN74LS442N uses a 20-pin PDIP package intended for through-hole mounting. The package count and technology are identified in the Texas Instruments component listing and corroborated by the product search results. Use the manufacturer's pin-description table when laying out the footprint and assigning the enable, direction, data, and ground connections.
Where can I download the SN74LS442N datasheet PDF?
The SN74LS442N datasheet PDF can be accessed through the Texas Instruments document listing linked from the product page, with a mirrored copy also identified in the verified document results. The document is titled as the SN74LS442N datasheet and covers the quadruple tridirectional bus transceiver. Use the manufacturer version for authoritative pinout, electrical limits, and operating information.
Where can I find the SN74LS442N pinout?
The SN74LS442N pinout is located in the pin-description section of the Texas Instruments datasheet for the 20-pin PDIP device. The component is documented as a four-channel, 4-bit, non-inverting, 3-state bus transceiver. Assign PCB tracks using the numbered package drawing and pin-description table rather than relying on signal names from a generic 74-series device.
Can the SN74LS442N drive a shared bidirectional bus?
The SN74LS442N can support a shared bidirectional bus when its tri-state outputs and direction controls are managed correctly. Because it is a tridirectional 4-bit transceiver, it can transfer data in either direction and disconnect an inactive output driver. Only one enabled driver should source a given bus segment at a time to prevent contention.
What should I check before replacing the SN74LS442N?
A replacement should match the SN74LS442N's 4-bit channel organization, non-inverting logic, 3-state output behavior, 20-pin PDIP footprint, and required logic-level timing. According to the 74-series cross-reference material, several manufacturers offered functionally similar 74LS442 devices, but the package drawing and pin table should still be compared before substitution.
What is the best drop-in replacement for the SN74LS442N?
A drop-in replacement must use the same 20-pin PDIP footprint and preserve the four 4-bit tridirectional channels, non-inverting logic, and tri-state control arrangement. The Rochester Electronics 74LS442N is a functionally relevant same-package candidate identified in the product search results. Confirm its pin table, supply requirements, and timing limits against the Texas Instruments datasheet before production use.
What can replace the SN74LS442N?
The closest functional replacements are 74LS442-family devices offered with a 20-pin PDIP footprint, including the Rochester Electronics 74LS442N. A valid replacement must preserve the non-inverting four-channel bus architecture and 3-state output behavior. Because equivalent naming does not prove identical pinout or timing, review the manufacturer datasheet and compare every enable and direction input.
Is the 74LS442N equivalent to the SN74LS442N?
The Rochester Electronics 74LS442N is a relevant equivalent candidate because it implements the same 74LS442 quadruple tridirectional bus-transceiver function in a 20-pin PDIP package. The SN74LS442N additionally carries the Texas Instruments ordering prefix. Pin compatibility should be confirmed from the two datasheets because device revisions and sourcing representations can differ.
When should I choose the SN74LS442N instead of a generic 74LS442?
Choose the SN74LS442N when a design is standardized around the Texas Instruments 20-pin PDIP implementation and its documented electrical and timing characteristics. A generic 74LS442N can be considered for legacy repair or supply-continuity situations when its pinout, supply voltage, propagation timing, and output loading meet the system requirements.
Is the SN74LS442N suitable for legacy industrial equipment?
The SN74LS442N is suitable for legacy equipment that uses TTL-compatible parallel buses and a 20-pin through-hole transceiver position. Its four 4-bit tridirectional channels support bidirectional exchange and tri-state isolation between shared bus segments. Validate the equipment's logic levels, timing margins, and bus-contention controls during qualification.
SN74LS442N vs 74LS442N: which is easier to source?
The SN74LS442N is the Texas Instruments-branded 20-pin PDIP implementation, while the 74LS442N designation can refer to a compatible device from another manufacturer. Availability depends on the exact manufacturer and suffix, so both the commercial status and pinout must be checked. Use the Request a Quote form on this page for current availability and sourcing support.
What are the key specifications of SN74LS442N that engineers should know?
The key specifications are four 4-bit channels, non-inverting tridirectional operation, 3-state outputs, and a 20-pin PDIP package. Texas Instruments identifies the SN74LS442N as a quadruple tridirectional bus transceiver. Supply voltage, current, propagation delay, and temperature limits should be taken from the specific manufacturer datasheet when they are required for design calculations.
Where can I buy the SN74LS442N and check its lead time?
Use the Request a Quote form on this page to request the SN74LS442N, current availability, and lead-time confirmation for the required package and quantity. Texas Instruments and Rochester Electronics product records are associated with this device, but stock and delivery timing can vary by order quantity and lifecycle status. The quote form provides a single direct sourcing path.
What is the price of the SN74LS442N?
Use the Request a Quote form on this page for a current SN74LS442N quotation. The exact price can depend on manufacturer, package, order quantity, and market availability, so a static figure may not reflect current purchasing conditions. The form allows the requested quantity and target supply requirements to be included in the inquiry.
Is the SN74LS442N in stock?
Current SN74LS442N stock should be confirmed through the Request a Quote form on this page. Product listings indicate market availability, but inventory levels and lead time can change by manufacturer and quantity. Include the required quantity and acceptable delivery date in the request so the latest fulfillment position can be evaluated.

Engineering reference data for SN74LS442N — comparison, design guidance, and compliance information.

Selection Guide

Choose the SN74LS442N when maintaining or reproducing a legacy design that specifically uses the Texas Instruments 20-pin PDIP implementation of the four-channel 4-bit tridirectional bus transceiver. It is particularly useful when a board requires 16 parallel bidirectional lines with non-inverting and 3-state behavior. Select the Rochester Electronics 74LS442N for a repair or supply-continuity candidate in the same functional class, after comparing its pin table and timing characteristics with the original device. DM74LS442N, MC74LS442, HD74LS442P, and TC74LS442 are additional legacy-family options for designers evaluating an alternative source. None should be installed solely because the generic 74LS442 name matches. Verify package dimensions, pin functions, enable polarity, propagation delay, supply requirements, output-current capability, and operating-temperature limits. For new mixed-signal or high-speed designs, consider a modern bus interface with defined electrical performance instead of reproducing a legacy TTL bus without a full timing review.

Comparison with Alternatives

Parameter This Product 74LS442N DM74LS442N MC74LS442 HD74LS442P TC74LS442
Brand Texas Instruments Rochester Electronics Fairchild Motorola Hitachi Toshiba
Package 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP
Device Function Quadruple tridirectional bus transceiver Quadruple tridirectional bus transceiver 74LS442 quadruple bus transceiver 74LS442 quadruple bus transceiver 74LS442 quadruple bus transceiver 74LS442 quadruple bus transceiver
Channel Organization 4 channels, 4 bits per element 4 channels, 4 bits per element 4 channels, 4 bits per element 4 channels, 4 bits per element 4 channels, 4 bits per element 4 channels, 4 bits per element
Signal Polarity Non-inverting Non-inverting Non-inverting Non-inverting Non-inverting Non-inverting
Output State 3-state 3-state 3-state 3-state 3-state 3-state
Logic Family 74LS 74LS 74LS 74LS 74LS 74LS
Mounting Type Through-hole Through-hole Through-hole Through-hole Through-hole Through-hole

Key Differentiators

  • Four grouped channels reduce the number of packages required for a 16-bit bidirectional interface (vs DM74LS442N)
  • Non-inverting 3-state operation preserves bus logic while allowing inactive drivers to disconnect (vs MC74LS442)
  • Texas Instruments documentation provides a defined source for footprint and timing verification (vs TC74LS442)

Design Notes

Prevent bus contention by ensuring that only one transceiver output is enabled to drive a shared node at a time. Decode enable and direction signals so that the old driver enters its high-impedance state before the new driver begins sourcing data. Review the timing values in the manufacturer datasheet when defining setup, hold, and dead-time margins around direction changes.

Use the 20-pin PDIP footprint from the manufacturer package drawing and maintain the specified lead pitch and row spacing. Place the device where its through-hole leads remain mechanically accessible for inspection and replacement. Assign every enable and direction input according to the numbered pin-description table, and avoid routing long shared-bus traces past sources of unrelated high-speed signals.

Account for bus loading, stub length, and receiver thresholds when using the SN74LS442N on a multi-segment parallel bus. Terminate or buffer long branches when required by the system architecture, and keep the 3-state control path free from timing hazards. Validate setup and hold timing at the intended clock or data-transfer rate rather than assuming that another bus device has identical propagation delay.

Analyze the complete bus interface power budget because every enabled driver contributes dynamic and static current, while multiple transceiver sections may operate simultaneously. Use the datasheet current limits for worst-case load, temperature, and supply conditions. Provide local bypassing on the logic supply and keep return-current paths close to the device to reduce supply disturbance and unintended transitions.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The product is a legacy 74LS-family logic IC; no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified. AEC-Q100 qualification is not indicated for this general-purpose logic device.

Data verified on: 2026-11-14 — data verified and curated by XAIPART's component engineering team

Related Searches

SN74LS442N datasheet SN74LS442N datasheet pdf SN74LS442N pinout SN74LS442N pin diagram SN74LS442N 20-pin PDIP SN74LS442N bus transceiver SN74LS442N equivalent SN74LS442N replacement SN74LS442N vs 74LS442N Texas Instruments SN74LS442N SN74LS442N price SN74LS442N stock SN74LS442N cross reference SN74LS442N application circuit 74LS quad tridirectional bus transceiver

Related Components & Terms

Texas Instruments SN74LS442N 74LS442N DM74LS442N MC74LS442 HD74LS442P TC74LS442 74LS TTL low-power Schottky TTL bus transceiver tridirectional transceiver parallel bus 3-state output high-impedance state non-inverting logic bidirectional bus bus contention digital logic IC interface IC 20-pin PDIP DIP package family through-hole mounting legacy industrial equipment
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details