SN74LS442N - 4-Bit 3-State Bus Transceiver | Texas Instruments
MPN: SN74LS442N ✓ نشطSN74LS442N نظرة عامة
A bus transceiver is a digital interface component that connects two logic sections through a shared bidirectional line. It belongs to the broader transceiver hierarchy: parallel bus transceiver, bidirectional transceiver, bus-interface IC, and digital logic IC. Unlike a unidirectional buffer, a tridirectional transceiver can support both data transmission and reception. Its 3-state output allows the output driver to disconnect electrically from the bus, preventing multiple connected devices from driving the same node simultaneously.
The SN74LS442N organizes four independent 4-bit channels into one 20-pin PDIP package. Each 4-bit section provides parallel data transfer, while the tridirectional architecture supports communication in either direction. The non-inverting implementation preserves the logical relationship between bus data and the corresponding transceiver-side signals. Three-state operation is particularly important for shared buses because it permits an inactive channel to avoid loading the common node.
The SN74LS442N belongs to the 74LS low-power Schottky TTL logic family. This family is used in systems that require conventional bipolar TTL-compatible interfacing rather than a modern low-voltage differential bus such as LVDS. Because the SN74LS442N operates as a parallel logic device, board-level design must account for shared-bus contention, direction-control sequencing, adequate signal settling time, and correct handling of every enable and direction input.
Typical uses include bidirectional data buffers, computer peripheral interfaces, bus isolation points, test equipment, and legacy industrial control systems. The device can sit between two bus segments when data must be exchanged in both directions without continuously loading either segment. It is also suitable for systems that require a defined high-impedance state during reset, test, or bus ownership changes. The 20-pin PDIP format favors through-hole assembly, repair, and legacy control-system maintenance.
For a reliable design, define the ownership of every bus segment so that only one enabled driver sources a given bit at a time. Direction and enable signals should be decoded cleanly and should not leave two transceivers driving simultaneously during transitions. Review signal timing and bus loading against the circuit requirements, and use the manufacturer's pin-description table when assigning PCB tracks. The PDIP footprint also requires adequate board spacing and appropriate lead-forming during insertion.
This page combines the device's exact catalog identity, package information, application guidance, qualified same-footprint alternatives, and design-oriented cautions. It focuses on the practical role of four non-inverting 4-bit channels and tri-state bus isolation while directing engineers to the manufacturer datasheet for authoritative electrical limits and timing conditions.
بدائل مباشرة لـ SN74LS442N — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
74LS442N
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DM74LS442N
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MC74LS442
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
HD74LS442P
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TC74LS442
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS442N المواصفات
| Product Type | Quadruple 4-bit bidirectional bus transceiver |
| Number of Elements | 1 element |
| Bits per Element | 4 bits per element |
| Channel Direction | Non-inverting, tridirectional |
| Output State | 3-state output |
| Number of Bus Channels | 4 channels |
| Total Parallel Data Width | 16 bits per device |
| العلبة | 20-pin PDIP |
| عدد الأطراف | 20 pins |
| نوع التركيب | Through-hole |
| Logic Family | 74LS low-power Schottky TTL |
دليل تكوين أطراف SN74LS442N 20-pin pdip
تكوين الأطراف لـ SN74LS442N (حزمة 20-pin pdip). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SN74LS442N.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
SN74LS442N مناسب لـ 6 التطبيقs: Bidirectional Parallel Data Buffer, Legacy Peripheral Bus Isolation, Computer Backplane Interconnect, Industrial Test Equipment Interface, Data Acquisition Module Backplane, Embedded Control System Bus Hub.
Bidirectional Parallel Data Buffer
The SN74LS442N fits legacy parallel systems that need data to move in either direction across a shared bus. Four 4-bit channels provide 16 parallel bits per device, while the 3-state outputs allow an inactive driver to disconnect from the node. Placing the transceiver between two bus segments can reduce contention and create a controlled interface point. The design must ensure that only one side drives a segment during any given interval. Direction decoding should include non-overlapping transitions so that neither side sources the bus while the other changes direction. Because this is a 20-pin PDIP device, it is especially suitable for repair-oriented and through-hole legacy equipment rather than compact surface-mount systems.
موصى به
Legacy Peripheral Bus Isolation
The SN74LS442N can isolate a legacy peripheral bus from the logic that controls bus ownership. Its four non-inverting 4-bit channels support 16 bits of bidirectional signaling, and the tri-state function keeps an unused driver electrically disconnected from the shared line. This arrangement is useful when a peripheral must be selected, disabled, or tested without continuously loading the processor-side bus. Firmware and hardware timing must ensure that enable and direction changes never create a period in which two enabled outputs contend. The through-hole PDIP package supports board-level repair and clear mechanical inspection in older industrial and instrumentation systems.
موصى به
Computer Backplane Interconnect
The SN74LS442N is applicable to legacy computer backplanes where a shared parallel bus must exchange data between two modules. Its four 4-bit sections provide grouped bidirectional channels, and each output can enter a high-impedance state when that channel is not enabled. This characteristic helps preserve signal integrity by preventing an idle transceiver from loading the bus. The design should assign ownership deterministically and account for propagation delay during direction handoff. The 20-pin PDIP format suits large-format control, test, and industrial computers where through-hole components and serviceability remain priorities.
موصى به
Industrial Test Equipment Interface
The SN74LS442N can connect a legacy test fixture to a controller while allowing the bus driver to disconnect during idle or measurement intervals. Its four 4-bit tridirectional channels provide a practical way to exchange multiple parallel status and command bits. The 3-state outputs help the fixture avoid loading circuitry that drives the same bus elsewhere. A robust implementation should disable transceivers before changing direction and use the manufacturer timing information to establish safe setup and hold margins. The PDIP package is mechanically convenient for instrument chassis and repairable production-test platforms.
موصى به
Data Acquisition Module Backplane
The SN74LS442N can be used in legacy data-acquisition modules that require a compact bidirectional parallel interface between a controller and an analog or digital front end. Four grouped 4-bit channels provide 16 lines for command, address, or multiplexed data, and tri-state operation permits the module to release shared lines when not selected. The design should keep analog-signal routing separate from the digital bus and use controlled enables to prevent contention. Its 20-pin PDIP package is well suited to modular backplanes where long service life and straightforward replacement are more important than minimum board area.
موصى به
Embedded Control System Bus Hub
The SN74LS442N can serve as a controlled hub in a legacy embedded system where two subsystems exchange commands over one parallel bus. The non-inverting 4-bit channels preserve bus logic while the tri-state outputs let a nonselected subsystem remain passive. This arrangement can simplify ownership compared with continuously enabled drivers, provided the controller asserts enable and direction signals in a non-overlapping sequence. Because the package is a 20-pin PDIP, the device is most attractive in control boards designed around through-hole logic and maintainable bus architecture rather than high-density mixed-signal products.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SN74LS442N — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | 74LS442N | DM74LS442N | MC74LS442 | HD74LS442P | TC74LS442 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Rochester Electronics | Fairchild | Motorola | Hitachi | Toshiba |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Device Function | Quadruple tridirectional bus transceiver | Quadruple tridirectional bus transceiver | 74LS442 quadruple bus transceiver | 74LS442 quadruple bus transceiver | 74LS442 quadruple bus transceiver | 74LS442 quadruple bus transceiver |
| Channel Organization | 4 channels, 4 bits per element | 4 channels, 4 bits per element | 4 channels, 4 bits per element | 4 channels, 4 bits per element | 4 channels, 4 bits per element | 4 channels, 4 bits per element |
| Signal Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Logic Family | 74LS | 74LS | 74LS | 74LS | 74LS | 74LS |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
أبرز الفروقات
- Four grouped channels reduce the number of packages required for a 16-bit bidirectional interface (مقابلDM74LS442N)
- Non-inverting 3-state operation preserves bus logic while allowing inactive drivers to disconnect (مقابلMC74LS442)
- Texas Instruments documentation provides a defined source for footprint and timing verification (مقابلTC74LS442)
ملاحظات التصميم
Prevent bus contention by ensuring that only one transceiver output is enabled to drive a shared node at a time. Decode enable and direction signals so that the old driver enters its high-impedance state before the new driver begins sourcing data. Review the timing values in the manufacturer datasheet when defining setup, hold, and dead-time margins around direction changes.
Use the 20-pin PDIP footprint from the manufacturer package drawing and maintain the specified lead pitch and row spacing. Place the device where its through-hole leads remain mechanically accessible for inspection and replacement. Assign every enable and direction input according to the numbered pin-description table, and avoid routing long shared-bus traces past sources of unrelated high-speed signals.
Account for bus loading, stub length, and receiver thresholds when using the SN74LS442N on a multi-segment parallel bus. Terminate or buffer long branches when required by the system architecture, and keep the 3-state control path free from timing hazards. Validate setup and hold timing at the intended clock or data-transfer rate rather than assuming that another bus device has identical propagation delay.
Analyze the complete bus interface power budget because every enabled driver contributes dynamic and static current, while multiple transceiver sections may operate simultaneously. Use the datasheet current limits for worst-case load, temperature, and supply conditions. Provide local bypassing on the logic supply and keep return-current paths close to the device to reduce supply disturbance and unintended transitions.
معلومات الامتثال
The product is a legacy 74LS-family logic IC; no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified. AEC-Q100 qualification is not indicated for this general-purpose logic device.