SN74LS540N - 8-Channel 5V Inverting 3-State Buffer | TI
MPN: SN74LS540N ✓ ActiveSN74LS540N Overview
A logic buffer or line driver is a digital IC that conditions and reproduces logic signals while increasing drive capability. The SN74LS540 belongs to the LS-series TTL logic hierarchy: octal buffer/line driver → 3-state logic buffer → bus driver → digital logic IC. Its principal purpose is to place stronger, controlled drivers between sensitive logic circuitry and shared or external data buses.
The three-state output function is the central feature of the SN74LS540N. Each output can actively drive a logic level, enter a high-impedance state, or be controlled by its dedicated active-low enable input. The inverting channel architecture means a low input produces a high output and a high input produces a low output. Placing inputs and outputs on opposite sides of the package separates the signal-flow directions and supports board-level routing.
The SN74LS540N uses bipolar LS-series technology and is specified for a 4.75 V to 5.25 V supply range. Its 20-pin PDIP construction supports through-hole assembly and repair workflows. As an eight-channel device, it can drive eight parallel bus lines in one package, reducing component count compared with discrete single-channel buffers. The enable-controlled high-impedance state is especially useful when multiple devices share a bus.
Typical uses include bidirectional data-bus buffering, memory and peripheral interface isolation, industrial control data buses, test-equipment signal paths, and legacy computer interfaces. The three-state outputs allow a controller to release a bus without creating a contention condition. Because the device is an inverting buffer and line driver, system designers must account for one inversion in address, control, or data-transfer logic.
PCB planning should preserve the DIP-20 footprint and provide adequate clearance around adjacent pins. Keep data and enable traces short where they connect to external buses, and avoid long unprotected stubs that could increase reflections. The Request a Quote form on this page supports current sourcing, price, stock, and lead-time inquiries for the exact SN74LS540N ordering code.
This product record combines the exact manufacturer and distributor identities, 4.75 V to 5.25 V operating range, eight-channel 3-state function, inverting behavior, 20-pin PDIP package, verified replacement options, and practical design guidance. It is intended to help engineers evaluate pin compatibility, bus contention, inversion, and legacy through-hole assembly requirements before releasing a design to production.
Drop-in alternatives for SN74LS540N — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with SN74LS540N (same form factor and footprint) — differing in Package.
SN74LS540N
✅ Drop-InContact for price
View Datasheet →74LS540N
✅ Drop-In📋 Reference alternative (not in catalog)
SN74LS540N
✅ Drop-InContact for price
View Datasheet →SN74LS540N Maximum Ratings & Electrical Characteristics
| Logic Type | Octal inverting buffer and line driver |
| Number of Channels | 8 channels |
| Output Type | 3-state, inverting |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Technology | Bipolar |
| Package | 20-pin PDIP |
| Mounting Type | Through-hole |
| Enable Control | Active-low |
| Input and Output Arrangement | Inputs and outputs on opposite sides of the package |
| High-Impedance Output State | Yes, per output channel |
SN74LS540N 20-pin pdip Pin Configuration Guide
Pin configuration for SN74LS540N (20-pin pdip package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for SN74LS540N.
Refer to the datasheet for full pin configuration.
Typical Applications
SN74LS540N is suitable for 6 applications: Shared Parallel Data Bus, Memory and Peripheral Interface Isolation, Industrial Control Signal Conditioning, Legacy Computer Backplane Buffering, Test and Measurement Interface, Peripheral Data-Path Buffering.
Shared Parallel Data Bus
The SN74LS540N fits a shared parallel bus where eight data lines must be driven or isolated. Its 4.75 V to 5.25 V supply range matches nominal 5 V TTL systems, while each inverting channel can enter a high-impedance state when its active-low enable is deasserted. This allows several devices to share one bus without simultaneous active drivers. Because every enabled data path is inverted, the surrounding address, control, or data protocol must include the corresponding polarity change. The 20-pin PDIP package also suits legacy control boards that require through-hole serviceability.
Recommended
Memory and Peripheral Interface Isolation
The SN74LS540N can isolate memory or peripheral data paths from a 5 V system bus while retaining the same eight-channel structure. Its eight 3-state outputs allow selected groups of lines to be released during bus turnaround, and the line-driver architecture is intended to provide stronger signal conditioning than unloaded logic outputs. The operating range of 4.75 V to 5.25 V suits nominal 5 V equipment, but the inverting behavior must be reconciled with the target interface protocol. Through-hole construction is useful when maintaining older industrial controller boards.
Recommended
Industrial Control Signal Conditioning
The SN74LS540N is suitable for legacy industrial control boards that need eight buffered logic channels and selective bus participation. Its bipolar implementation operates across the 4.75 V to 5.25 V range specified for the SN74LS540 family, allowing it to operate from a regulated 5 V rail. The active-low, 3-state enable arrangement supports command buses where peripheral outputs must be disconnected while another subsystem drives the line. Designers should preserve the device’s inversion in control logic and validate noise margin, timing, and load current for the specific system.
Recommended
Legacy Computer Backplane Buffering
The SN74LS540N can serve as a backplane or card-edge line driver in a 5 V legacy computer architecture. Its eight channels provide consistent inversion and independent 3-state control across a group of parallel conductors, while placing inputs and outputs on opposite sides of the package aids directional routing. The 20-pin PDIP footprint is particularly relevant for repairable and through-hole backplane designs. Designers must budget for the logic inversion, keep disabled outputs in high impedance, and account for the LS-family switching characteristics when configuring clocked or multiplexed bus signals.
Recommended
Test and Measurement Interface
The SN74LS540N can condition control lines in test and measurement equipment built around a 5 V digital control architecture. Eight inverting channels with selectable high-impedance outputs help connect a controller to external fixtures while isolating inactive driver sections. This is useful when several test points or instrument-control signals share a common set of conductors. The 4.75 V to 5.25 V supply range supports standard 5 V logic, while the PDIP package simplifies insertion into laboratory adapters. Signal-integrity checks should include ringing, capacitive loading, and timing margins at the connected cable or fixture.
Recommended
Peripheral Data-Path Buffering
The SN74LS540N fits peripheral-to-processor data paths requiring eight buffered channels, a 5 V supply, and controlled disconnect capability. It can place a group of peripheral signals onto a bus only when the associated enable is active and remove its drivers when the bus is assigned elsewhere. The inverting architecture must be included in the interface truth table, particularly for chip-select and request signals that are often active-low. Its through-hole PDIP package is beneficial in equipment designed around replaceable logic boards, repair stocks, and long-life industrial systems.
Recommended
Recommended Products Summary
Engineering reference data for SN74LS540N — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | SN74LS540N | 74LS540N | SN74LS540N |
|---|---|---|---|---|
| Brand | Texas Instruments | onsemi | Motorola | Motorola |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Logic Polarity | Inverting | Inverting | Inverting | Inverting |
| Output Function | 3-state line driver | 3-state line driver | 3-state line driver | 3-state line driver |
Key Differentiators
- Eight channels combined with independent 3-state control (vs SN74LS125N)
- Opposite-side input and output package arrangement (vs SN74LS240N)
- Exact second-source ordering options (vs SN74LS540N from onsemi and Motorola)
Design Notes
Do not replace the SN74LS540N with the SN74LS541N without changing the system truth table. The SN74LS540N is inverting, so each enabled channel reverses the input state; the SN74LS541N is non-inverting. A physical fit alone does not make the two devices functionally interchangeable, particularly on active-low chip-select, interrupt, request, or acknowledge signals.
Operate the SN74LS540N from a regulated 5 V supply that remains within its specified 4.75 V to 5.25 V range. Check the source rail for noise and sequencing constraints at every board power state. Because multiple channels can be enabled simultaneously, validate aggregate package dissipation and output loading against the manufacturer’s operating limits rather than examining only one channel at a time.
Preserve the 20-pin PDIP footprint, including lead spacing and pin-1 orientation, when creating a replacement board. Place the device away from heat sources and provide clearance for through-hole soldering and inspection. Follow the manufacturer pin-description table when assigning inputs, outputs, and active-low enables; the opposing input and output sides of the package are intentional and should not be mirrored accidentally.
Use the 3-state output only when the connected bus requires controlled isolation. Ensure no two enabled drivers contend for the same conductor, and design pull-up or pull-down termination appropriate to the system bus. Account for one logic inversion per enabled data channel and verify propagation-delay compatibility in multiplexed or clocked interfaces before substituting an equivalent part.
Compliance Information
The manufacturer product-page and datasheet results do not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements. The general-purpose SN74LS540N designation does not by itself establish AEC-Q100 qualification.