Texas Instruments

SN74LS540N - 8-Channel 5V Inverting 3-State Buffer | TI

Référence : SN74LS540N ✓ Actif
4.75 V to 5.25 V Vdss 20-pin PDIP Package
MOQ : 1 |

SN74LS540N Présentation

The Texas Instruments SN74LS540N is an 8-channel, inverting, 3-state octal buffer and line driver operating from 4.75 V to 5.25 V, supplied in a 20-pin PDIP package. Its eight channels provide non-inverting data paths, active-low output enables, and high-impedance output states for bus isolation.

A logic buffer or line driver is a digital IC that conditions and reproduces logic signals while increasing drive capability. The SN74LS540 belongs to the LS-series TTL logic hierarchy: octal buffer/line driver → 3-state logic buffer → bus driver → digital logic IC. Its principal purpose is to place stronger, controlled drivers between sensitive logic circuitry and shared or external data buses.

The three-state output function is the central feature of the SN74LS540N. Each output can actively drive a logic level, enter a high-impedance state, or be controlled by its dedicated active-low enable input. The inverting channel architecture means a low input produces a high output and a high input produces a low output. Placing inputs and outputs on opposite sides of the package separates the signal-flow directions and supports board-level routing.

The SN74LS540N uses bipolar LS-series technology and is specified for a 4.75 V to 5.25 V supply range. Its 20-pin PDIP construction supports through-hole assembly and repair workflows. As an eight-channel device, it can drive eight parallel bus lines in one package, reducing component count compared with discrete single-channel buffers. The enable-controlled high-impedance state is especially useful when multiple devices share a bus.

Typical uses include bidirectional data-bus buffering, memory and peripheral interface isolation, industrial control data buses, test-equipment signal paths, and legacy computer interfaces. The three-state outputs allow a controller to release a bus without creating a contention condition. Because the device is an inverting buffer and line driver, system designers must account for one inversion in address, control, or data-transfer logic.

PCB planning should preserve the DIP-20 footprint and provide adequate clearance around adjacent pins. Keep data and enable traces short where they connect to external buses, and avoid long unprotected stubs that could increase reflections. The Request a Quote form on this page supports current sourcing, price, stock, and lead-time inquiries for the exact SN74LS540N ordering code.

This product record combines the exact manufacturer and distributor identities, 4.75 V to 5.25 V operating range, eight-channel 3-state function, inverting behavior, 20-pin PDIP package, verified replacement options, and practical design guidance. It is intended to help engineers evaluate pin compatibility, bus contention, inversion, and legacy through-hole assembly requirements before releasing a design to production.

Alternatives de remplacement direct pour SN74LS540N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec SN74LS540N (même facteur de forme et même empreinte) — différant par Package.

onsemi
Package: DIP-20
Comparer avec SN74LS540N →

SN74LS540N

✅ Remplacement direct
Texas Instruments
📦 20-pin PDIP
Octal inverting buffer and line driver · 8 channels · 3-state, inverting · 4.75 V to 5.25 V · Bipolar · 20-pin PDIP · Through-hole · Active-low

Contactez-nous pour le prix

Voir la fiche technique →

74LS540N

✅ Remplacement direct
📦 20-pin PDIP
Motorola 74LS540N retains the 8-channel, 4.75 V to 5.25 V, inverting 3-state function; only the manufacturer prefix differs from SN74LS540N.

📋 Alternative de référence (hors catalogue)

SN74LS540N

✅ Remplacement direct
Texas Instruments
📦 20-pin PDIP
Octal inverting buffer and line driver · 8 channels · 3-state, inverting · 4.75 V to 5.25 V · Bipolar · 20-pin PDIP · Through-hole · Active-low

Contactez-nous pour le prix

Voir la fiche technique →

SN74LS540N Valeurs maximales et caractéristiques électriques

Logic Type Octal inverting buffer and line driver
Number of Channels 8 channels
Type de sortie 3-state, inverting
Supply Voltage Range 4.75 V to 5.25 V
Technology Bipolar
Boîtier 20-pin PDIP
Type de montage Through-hole
Enable Control Active-low
Input and Output Arrangement Inputs and outputs on opposite sides of the package
High-Impedance Output State Yes, per output channel

Guide de configuration des broches du SN74LS540N 20-pin pdip

Configuration des broches du SN74LS540N (boîtier 20-pin pdip). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.

Schéma de brochage du boîtier 20-pin pdip pour le SN74LS540N

Aucune donnée de brochage détaillée disponible pour SN74LS540N.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

SN74LS540N convient pour 6 applications: Shared Parallel Data Bus, Memory and Peripheral Interface Isolation, Industrial Control Signal Conditioning, Legacy Computer Backplane Buffering, Test and Measurement Interface, Peripheral Data-Path Buffering.

🖥️

Shared Parallel Data Bus

The SN74LS540N fits a shared parallel bus where eight data lines must be driven or isolated. Its 4.75 V to 5.25 V supply range matches nominal 5 V TTL systems, while each inverting channel can enter a high-impedance state when its active-low enable is deasserted. This allows several devices to share one bus without simultaneous active drivers. Because every enabled data path is inverted, the surrounding address, control, or data protocol must include the corresponding polarity change. The 20-pin PDIP package also suits legacy control boards that require through-hole serviceability.

🏭

Memory and Peripheral Interface Isolation

The SN74LS540N can isolate memory or peripheral data paths from a 5 V system bus while retaining the same eight-channel structure. Its eight 3-state outputs allow selected groups of lines to be released during bus turnaround, and the line-driver architecture is intended to provide stronger signal conditioning than unloaded logic outputs. The operating range of 4.75 V to 5.25 V suits nominal 5 V equipment, but the inverting behavior must be reconciled with the target interface protocol. Through-hole construction is useful when maintaining older industrial controller boards.

⚡

Industrial Control Signal Conditioning

The SN74LS540N is suitable for legacy industrial control boards that need eight buffered logic channels and selective bus participation. Its bipolar implementation operates across the 4.75 V to 5.25 V range specified for the SN74LS540 family, allowing it to operate from a regulated 5 V rail. The active-low, 3-state enable arrangement supports command buses where peripheral outputs must be disconnected while another subsystem drives the line. Designers should preserve the device’s inversion in control logic and validate noise margin, timing, and load current for the specific system.

🖥️

Legacy Computer Backplane Buffering

The SN74LS540N can serve as a backplane or card-edge line driver in a 5 V legacy computer architecture. Its eight channels provide consistent inversion and independent 3-state control across a group of parallel conductors, while placing inputs and outputs on opposite sides of the package aids directional routing. The 20-pin PDIP footprint is particularly relevant for repairable and through-hole backplane designs. Designers must budget for the logic inversion, keep disabled outputs in high impedance, and account for the LS-family switching characteristics when configuring clocked or multiplexed bus signals.

🔧

Test and Measurement Interface

The SN74LS540N can condition control lines in test and measurement equipment built around a 5 V digital control architecture. Eight inverting channels with selectable high-impedance outputs help connect a controller to external fixtures while isolating inactive driver sections. This is useful when several test points or instrument-control signals share a common set of conductors. The 4.75 V to 5.25 V supply range supports standard 5 V logic, while the PDIP package simplifies insertion into laboratory adapters. Signal-integrity checks should include ringing, capacitive loading, and timing margins at the connected cable or fixture.

🖥️

Peripheral Data-Path Buffering

The SN74LS540N fits peripheral-to-processor data paths requiring eight buffered channels, a 5 V supply, and controlled disconnect capability. It can place a group of peripheral signals onto a bus only when the associated enable is active and remove its drivers when the bus is assigned elsewhere. The inverting architecture must be included in the interface truth table, particularly for chip-select and request signals that are often active-low. Its through-hole PDIP package is beneficial in equipment designed around replaceable logic boards, repair stocks, and long-life industrial systems.

Récapitulatif des produits recommandés

SN74LS240N Texas Instruments Utilisé dans : Shared Parallel Data Bus, Legacy Computer Backplane Buffering SN74LS125N Related quad 3-state buffer Utilisé dans : Shared Parallel Data Bus, Test and Measurement Interface SN74LS373N Related octal 3-state register Utilisé dans : Memory and Peripheral Interface Isolation, Peripheral Data-Path Buffering SN74LS374N Related edge-triggered octal register Utilisé dans : Memory and Peripheral Interface Isolation, Peripheral Data-Path Buffering SN74LS241N Texas Instruments Utilisé dans : Industrial Control Signal Conditioning SN74LS244N Texas Instruments Utilisé dans : Industrial Control Signal Conditioning, Test and Measurement Interface SN74LS138N Related 3-to-8 decoder for bus selection Utilisé dans : Legacy Computer Backplane Buffering
What is the operating voltage of SN74LS540N?
The SN74LS540N operates from 4.75 V to 5.25 V, according to the Texas Instruments SN74LS540 product page and the manufacturer datasheet SDLS180. This range corresponds to a nominal 5 V LS-series logic supply. The design should remain inside that interval during normal operation, and the component should not be treated as a 3.3 V-only or wide-range device.
What does the SN74LS540N do?
The SN74LS540N is an 8-channel, inverting, 3-state octal buffer and line driver. According to the Texas Instruments SN74LS540 product page, it provides eight channels with individually controlled 3-state outputs. Each channel inverts its input and can be placed in a high-impedance state, allowing several devices to share a bus when only one is enabled.
How many pins does SN74LS540N have?
The SN74LS540N has 20 pins in a PDIP package. The DigiKey product record identifies the exact SN74LS540N as a 20-PDIP octal inverting buffer with 3-state outputs. It is a through-hole logic device rather than a surface-mount package, so a PCB replacement must provide the appropriate 20-pin dual-inline footprint and adequate lead spacing.
Where can I download the SN74LS540N datasheet PDF?
The SN74LS540N datasheet PDF is available from the Texas Instruments document link on this page. The manufacturer document is titled “Octal Buffers and Line Drivers With 3-State Outputs” and carries the SDLS180 identifier shown in the document listing. It covers the SN54LS540, SN54LS541, SN74LS540, and SN74LS541 device families and includes the primary electrical and pin information.
Where can I find the SN74LS540N pinout?
Use the pin-description table and package drawing in the Texas Instruments SN74LS540 manufacturer datasheet to assign PCB nets. The device is a 20-pin PDIP, and its defining package arrangement places inputs and outputs on opposite sides of the body. Verify every enable and data pin against the exact datasheet table before fabrication because logic-level polarity must also be checked.
Is SN74LS540N inverting or non-inverting?
The SN74LS540N is inverting. The Texas Instruments product description identifies the family as 8-channel inverters with 3-state outputs, while the distributor listing calls the exact device an inverting buffer. Consequently, each enabled channel reverses the input logic state, so system logic must include that inversion unless another circuit stage restores the required polarity.
What is the best drop-in replacement for SN74LS540N?
The safest replacement strategy is to use an exact second-source 74LS540N with the same 20-pin PDIP footprint, 4.75 V to 5.25 V supply range, inverting channel function, and active-low 3-state enable arrangement. The cross-reference results identify onsemi and Motorola versions of SN74LS540N. Confirm electrical details against the relevant manufacturer datasheet before substituting a part.
Can onsemi SN74LS540N replace Texas Instruments SN74LS540N?
Yes, the onsemi SN74LS540N is a candidate drop-in replacement because it uses the same SN74LS540N ordering code and function designation. The Octopart result identifies an onsemi SN74LS540N listing, while the manufacturer family description defines the device as an 8-channel, 4.75 V to 5.25 V, inverting 3-state driver. Final qualification should confirm package and pin compatibility against the onsemi datasheet.
What is the difference between SN74LS540N and SN74LS541N?
The SN74LS540N is an inverting 3-state octal buffer, whereas the SN74LS541N is the non-inverting counterpart. Both occupy the same 20-pin PDIP package and use the same 4.75 V to 5.25 V supply range, but changing inversion alters the logical meaning of every data path. The SN74LS541N should therefore not be treated as a pin-for-pin behavioral replacement.
When should I choose SN74LS540N over a discrete buffer implementation?
Choose the SN74LS540N when a design needs eight matched, inverting, 3-state logic channels in one through-hole package. A discrete implementation would require eight comparable buffer elements and their associated enable routing, increasing footprint and part count. The SN74LS540N is preferable when its documented 5 V operating range and bipolar timing are appropriate for the target legacy system.
Is SN74LS540N suitable for shared data-bus applications?
Yes, the SN74LS540N is suitable for shared data buses because every output channel supports a 3-state high-impedance condition. The Texas Instruments datasheet describes octal buffers and line drivers with 3-state outputs. Only one driver should actively enable a shared line at a time, and external logic must account for the device’s inverting data path.
What are the key specifications of SN74LS540N that engineers should know?
The key SN74LS540N specifications are 8 channels, a 4.75 V to 5.25 V supply range, bipolar LS-series implementation, inverting 3-state outputs, active-low output enable control, and a 20-pin PDIP package. According to the Texas Instruments product page and manufacturer datasheet SDLS180, the device also places inputs and outputs on opposite sides of the package.
Where can I buy SN74LS540N online?
Use the Request a Quote form on this page to request the exact Texas Instruments SN74LS540N, current unit availability, and delivery information. The form preserves the exact 20-PDIP ordering code and avoids ambiguity with SN74LS541N or other LS-series buffers. Confirm current stock, minimum order quantity, and lead time directly through the quotation response.
What is the price of SN74LS540N?
The current SN74LS540N price should be obtained through the Request a Quote form on this page because commercial terms and availability can change with market conditions. Submit the exact MPN SN74LS540N and required quantity to receive a current quotation. The quotation response is the appropriate source for unit pricing, stock, and lead-time confirmation.
What is the lead time for SN74LS540N?
Current lead time for SN74LS540N depends on manufacturer inventory, the requested quantity, and packaging requirements. Submit the exact MPN and quantity through the Request a Quote form on this page for a current manufacturing and delivery commitment. For production planning, request the lead time before releasing the long-lead component schedule.
Is SN74LS540N RoHS compliant and automotive qualified?
The RoHS, REACH, lead-free, halogen-free, and automotive-qualification status of SN74LS540N require confirmation from the manufacturer’s current product documentation and ordering information. Do not infer automotive qualification from the commercial SN74LS540N designation alone. The component should be treated as a general-purpose 5 V bipolar logic IC unless the manufacturer explicitly states otherwise.

Données de référence d'ingénierie pour SN74LS540N — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the Texas Instruments SN74LS540N when repairing or designing a nominal 5 V system that needs eight inverting, 3-state bus drivers in a 20-pin PDIP footprint. Its defining advantages are the 4.75 V to 5.25 V supply range, per-channel high-impedance outputs, and the deliberate placement of inputs and outputs on opposite sides of the package. Choose SN74LS241N when the same 3-state bus-driver architecture is needed without data inversion. Choose SN74LS125N when only four independently enabled buffers are required, reducing package count at the cost of fewer channels. Choose SN74LS240N when an octal 3-state driver family is required and its package arrangement is appropriate for the target board. For second-source procurement, compare the onsemi and Motorola SN74LS540N records against the Texas Instruments datasheet, including pinout, enable polarity, timing, output loading, and lifecycle status.

Comparaison avec les alternatives

Paramètre Ce produit SN74LS540N 74LS540N SN74LS540N
Brand Texas Instruments onsemi Motorola Motorola
Package 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP
Number of Channels 8 channels 8 channels 8 channels 8 channels
Supply Voltage Range 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V
Logic Polarity Inverting Inverting Inverting Inverting
Output Function 3-state line driver 3-state line driver 3-state line driver 3-state line driver

Principaux différenciateurs

  • Eight channels combined with independent 3-state control (vs SN74LS125N)
  • Opposite-side input and output package arrangement (vs SN74LS240N)
  • Exact second-source ordering options (vs SN74LS540N from onsemi and Motorola)

Notes de conception

Do not replace the SN74LS540N with the SN74LS541N without changing the system truth table. The SN74LS540N is inverting, so each enabled channel reverses the input state; the SN74LS541N is non-inverting. A physical fit alone does not make the two devices functionally interchangeable, particularly on active-low chip-select, interrupt, request, or acknowledge signals.

Operate the SN74LS540N from a regulated 5 V supply that remains within its specified 4.75 V to 5.25 V range. Check the source rail for noise and sequencing constraints at every board power state. Because multiple channels can be enabled simultaneously, validate aggregate package dissipation and output loading against the manufacturer’s operating limits rather than examining only one channel at a time.

Preserve the 20-pin PDIP footprint, including lead spacing and pin-1 orientation, when creating a replacement board. Place the device away from heat sources and provide clearance for through-hole soldering and inspection. Follow the manufacturer pin-description table when assigning inputs, outputs, and active-low enables; the opposing input and output sides of the package are intentional and should not be mirrored accidentally.

Use the 3-state output only when the connected bus requires controlled isolation. Ensure no two enabled drivers contend for the same conductor, and design pull-up or pull-down termination appropriate to the system bus. Account for one logic inversion per enabled data channel and verify propagation-delay compatibility in multiplexed or clocked interfaces before substituting an equivalent part.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The manufacturer product-page and datasheet results do not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements. The general-purpose SN74LS540N designation does not by itself establish AEC-Q100 qualification.

Données vérifiées le : 2026-11-18 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

SN74LS540N datasheet SN74LS540N datasheet pdf SN74LS540N pinout SN74LS540N equivalent SN74LS540N replacement SN74LS540N cross reference SN74LS540N vs SN74LS241N SN74LS540N vs SN74LS125N SN74LS540N 20 pin PDIP SN74LS540N 5V 3-state buffer Texas Instruments SN74LS540N SN74LS540N price SN74LS540N stock SN74LS540N application circuit

Composants & termes associés

Texas Instruments SN74LS540N SN74LS540 SN74LS541N SN74LS240N SN74LS241N SN74LS244N SN74LS125N SN74LS373N SN74LS374N octal buffer line driver 3-state output inverting logic bipolar TTL LS-series logic logic IC digital buffer bus driver high-impedance state active-low enable parallel data bus 20-pin PDIP through-hole package 4.75 V to 5.25 V supply
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ