THS3111ID - 90 MHz Low-Noise Current-Feedback Amplifier | TI
MPN: THS3111ID ✓ ActiveTHS3111ID Overview
A current-feedback amplifier is a voltage-feedback amplifier variation that uses an internal transimpedance input stage and feedback impedance to set gain. Unlike a conventional voltage-feedback amplifier, a current-feedback amplifier maintains high bandwidth across a broad gain range, although its gain-setting resistor value and feedback network remain important to the final signal-integrity result. The THS3111ID combines this architecture with low-noise operation for instrumentation, video, communications, and industrial signal-conditioning systems.
The device provides 2 pA/sqrt(Hz) noninverting current noise, 10 pA/sqrt(Hz) inverting current noise, and 3 nV/sqrt(Hz) voltage noise. Its 90 MHz bandwidth supports high-speed waveform and signal-processing requirements. The specified 1300 V/us slew rate applies at an 8 V peak-to-peak load, while the 260 mA output-current capability provides useful drive for capacitive, transformer, and cable-style loads when the output-stage operating conditions are respected.
The THS3111ID uses a current-feedback topology rather than a conventional closed-loop voltage-feedback architecture. In a current-feedback design, the feedback resistor is normally placed in the feedback path and its value is selected for the required gain; the datasheet gain-versus-frequency and gain-versus-resistor guidance should be used rather than treating the part as a fixed-gain voltage-feedback amplifier. The wide supply range supports split-supply signal paths while preserving headroom for output swing.
Typical applications include video amplification, high-speed instrumentation, active filters, communications interfaces, and low-noise signal conditioning. The amplifier can also serve industrial measurement systems when its input common-mode range, output swing, noise, bandwidth, and load-drive requirements fit the selected operating point. PCB-level decoupling and short feedback paths are essential for preserving the high bandwidth and low-noise performance.
For a stable implementation, place the power bypass capacitors close to the supply pins, keep the inverting input and feedback components compact, and terminate unused inputs appropriately. Confirm output swing, input common-mode range, load capacitance, and thermal conditions with the manufacturer datasheet before operation. This page combines the manufacturer product information with practical design guidance and a parameter-by-parameter comparison framework.
Drop-in alternatives for THS3111ID — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with THS3111ID (same form factor and footprint) — differing in Amplifier Type, Inverting Current Noise, Noninverting Current Noise, Slew Rate, Supply Voltage Range.
THS3110IDR
✅ Drop-In📋 Reference alternative (not in catalog)
THS3111IDG4
✅ Drop-In📋 Reference alternative (not in catalog)
THS3111IDR
✅ Drop-In📋 Reference alternative (not in catalog)
THS3111ID Maximum Ratings & Electrical Characteristics
| Amplifier Type | Current-Feedback Amplifier |
| Channel Count | 1 channel |
| Supply Voltage Range | +/-5 V to +/-15 V |
| Bandwidth | 90 MHz |
| Slew Rate | 1300 V/us at RL = 8 VPP |
| Noninverting Current Noise | 2 pA/sqrt(Hz) |
| Inverting Current Noise | 10 pA/sqrt(Hz) |
| Voltage Noise | 3 nV/sqrt(Hz) |
| Output Current Drive | 260 mA |
| Package | 8-pin SOIC (D) |
| Mounting Type | Surface Mount |
| Product Description | Single low-noise, high-voltage current-feedback amplifier |
| Application Category | Instrumentation, operational amplifier, buffer amplifier |
THS3111ID 8-pin soic (d) Pin Configuration Guide
Pin configuration for THS3111ID (8-pin soic (d) package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for THS3111ID.
Refer to the datasheet for full pin configuration.
Typical Applications
THS3111ID is suitable for 6 applications: High-Speed Video Signal Conditioning, Industrial Instrumentation Signal Conditioning, Communications Receiver Front End, Active Filtering and Frequency Shaping, Audio and Low-Level Analog Amplification, Data Acquisition and ADC Drive.
High-Speed Video Signal Conditioning
The THS3111ID fits video buffering and gain stages that benefit from a 90 MHz bandwidth and 1300 V/us slew rate. Its 260 mA output-current capability helps drive terminated cables, resistive loads, and downstream stages when the load and output-swing conditions remain within the manufacturer limits. The 3 nV/sqrt(Hz) voltage noise is useful when low-level video signals must pass through the amplifier without adding excessive broadband noise. Use the current-feedback feedback network specified in the manufacturer data sheet rather than applying a voltage-feedback resistor formula. PCB placement should minimize the feedback path and keep bypass capacitors close to the device.
Recommended
Industrial Instrumentation Signal Conditioning
The THS3111ID is appropriate for instrumentation chains that require fast settling and low-noise amplification of sensor or measurement signals. Its 90 MHz bandwidth handles higher-bandwidth transducers more effectively than a slow precision amplifier, while 2 pA/sqrt(Hz) noninverting current noise and 3 nV/sqrt(Hz) voltage noise address sensitive front ends. The ±5 V to ±15 V operating range supports bipolar acquisition systems. Designers should confirm the input common-mode range at the selected supply and gain, then verify gain error and output swing before committing the circuit to a precision measurement application.
Recommended
Communications Receiver Front End
The THS3111ID can amplify intermediate-frequency or baseband signals in communications equipment when the designer needs 90 MHz bandwidth and rapid slew-rate performance. Its 1300 V/us slew rate helps preserve large, fast transitions, while 260 mA output drive supports terminated receiver stages. The split-supply capability of ±5 V to ±15 V permits biasing around a central signal level. The amplifier's current-feedback architecture makes feedback-resistor selection critical, and PCB parasitics can materially affect high-frequency behavior. Validate the full gain network and output load with the manufacturer application guidance before production release.
Recommended
Active Filtering and Frequency Shaping
The THS3111ID is well suited to wideband active-filter stages because its 90 MHz bandwidth and 1300 V/us slew rate support signal processing beyond the bandwidth of many general-purpose amplifiers. The device's 260 mA output-current capability is beneficial when the filter drives a termination or a following stage. Current-feedback gain behavior must be considered because changing the feedback resistor affects the realized gain and bandwidth. Select component values using the manufacturer gain and stability guidance, keep the inverting input and feedback network compact, and check the output for peaking at the filter's operating frequencies.
Recommended
Audio and Low-Level Analog Amplification
The THS3111ID can serve low-level analog amplification stages where low noise, wide bandwidth, and fast transient response are important. Its 3 nV/sqrt(Hz) voltage noise and 2 pA/sqrt(Hz) noninverting current noise are useful for preserving small signals, while the 1300 V/us slew rate provides ample headroom for fast transitions. The wide bandwidth may exceed what an audio application requires, so the final design should account for integrated noise across the selected filter bandwidth and verify that the amplifier's output drive is appropriate for the audio load and stabilization network.
Recommended
Data Acquisition and ADC Drive
The THS3111ID is useful as an analog driver in high-speed data-acquisition systems when the ADC requires low noise and rapid settling. Its 90 MHz bandwidth, 1300 V/us slew rate, and 260 mA output drive can reduce the burden on the converter input network. The exact suitability depends on the ADC's input bandwidth, settling requirements, sampling rate, and capacitive input loading. Use short PCB routes and proper termination to limit reflection and distortion. Check the output swing and drive behavior at the required voltage, then compare measured settling and distortion against the acquisition budget.
Recommended
Recommended Products Summary
Engineering reference data for THS3111ID — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | THS3110IDR | THS3111IDG4 | THS3111IDR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) - same package | 8-pin SOIC (D) - same package | 8-pin SOIC (D) - same package |
| Amplifier Architecture | Current-Feedback Amplifier | Current-Feedback Amplifier | Current-Feedback Amplifier | Current-Feedback Amplifier |
| Channel Count | 1 channel | 1 channel | 1 channel | 1 channel |
Key Differentiators
- Wideband current-feedback performance (vs THS3110IDR)
- Low current and voltage noise (vs THS3111IDR)
- Output drive for terminated and downstream loads (vs THS3111IDG4)
Design Notes
Place the feedback resistor, inverting input connection, and input compensation components close to the THS3111ID. Current-feedback amplifiers are sensitive to parasitic capacitance in the feedback loop, so long traces can alter gain, peaking, and stability. Route the output to the load without unnecessary stubs, use a solid ground reference, and confirm the feedback network against the manufacturer gain and stability guidance.
Use the supply bypass configuration recommended in the manufacturer data sheet and place the capacitors immediately adjacent to the supply pins. Keep the loop formed by the device, capacitors, and ground plane as short as practical. The THS3111ID supports ±5 V to ±15 V operation, but the usable output swing and input range are narrower than the full rail-to-rail envelope and must be checked for each design.
Evaluate output loading, cable termination, and downstream input capacitance before relying on the 260 mA output-current capability. The 90 MHz bandwidth makes board-level return paths and ground inductance important, especially around large-signal transitions. If the gain-setting resistor is changed, recheck both gain and bandwidth because current-feedback amplifiers do not follow the voltage-feedback gain relationship.
Do not copy a feedback resistor from a conventional voltage-feedback amplifier or assume that two current-feedback parts with the same package have identical gain behavior. Verify pin assignments, feedback values, compensation, output swing, and operating-point requirements in the manufacturer data sheet. This is particularly important when substituting THS3110IDR for THS3111ID in a high-gain or precision signal path.
Compliance Information
The manufacturer product information identifies the THS3111 family and orderable THS3111ID, but the available records do not explicitly state the compliance values shown above. Confirm current material and quality documentation with Texas Instruments before production release.