THS8136PHP - Triple 10-Bit 180-MSPS Video DAC | Texas Instruments
MPN: THS8136PHP ✓ ActiveTHS8136PHP Overview
A DAC is a data converter that translates digital color or graphics codes into proportional analog voltages. The THS8136 belongs to the video DAC category, a specialized form of digital-to-analog converter used to drive analog display and video-processing equipment. Its parallel interface, triple-channel architecture, and integrated sync and blanking support place it within high-speed video signal-chain components rather than general-purpose precision DACs.
The device provides three 10-bit DAC channels operating at sampling rates up to 180 MHz. Its 1.8 V digital supply supports modern digital graphics logic, while the 3.3 V analog supply provides the operating rail for the output converters. A common full-scale-adjustment resistor sets the output range of all three channels, and a 3.8-kilohm resistor is suitable for systems targeting approximately 700 mV full-scale output levels. The 0.015-microsecond settling time supports high-speed pixel and video timing requirements.
Internal circuitry generates bi-level synchronization and blanking levels for RGB and YPbPr color spaces. These functions reduce the amount of external glue logic needed when generating composite or component video signals. The parallel digital inputs accept sampled video data, while the three analog outputs provide independent red, green, and blue channels. This integration makes the THS8136 useful in graphics controllers, video splitters, frame buffers, digital display systems, and test equipment.
A typical implementation places the three DAC outputs on controlled impedance PCB traces and connects the digital input bus to the graphics or video source. Designers should terminate and route the high-speed digital interface carefully because edge-rate harmonics can radiate even though the maximum sampling rate is 180 MHz. Analog and digital return currents should be managed so switching activity does not disturb the output reference.
The principal design trade-off is integration versus operating flexibility. The THS8136PHP combines three converters and video-control functions in one package, reducing external circuitry, but its dedicated video feature set makes it less suitable than a general-purpose DAC when arbitrary analog waveforms, calibration, or multiple independent output ranges are required. Confirm package pin assignments and exposed-pad requirements in the manufacturer datasheet before layout release.
This product overview combines the manufacturer’s device description with package, interface, output-adjustment, and ordering details that help engineers assess the THS8136PHP before designing a video DAC signal chain. It also clarifies the distinctions among same-device ordering options and pin-compatible industrial-grade variants.
Drop-in alternatives for THS8136PHP — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with THS8136PHP (same form factor and footprint) — differing in Maximum Sampling Rate.
THS8136IPHP
✅ Drop-In📋 Reference alternative (not in catalog)
THS8136PHPR
✅ Drop-In📋 Reference alternative (not in catalog)
THS8136IPHPR
✅ Drop-In📋 Reference alternative (not in catalog)
THS8136PHP Maximum Ratings & Electrical Characteristics
| Converter Type | Triple 10-bit video digital-to-analog converter |
| Number of DAC Channels | 3 channels |
| Resolution | 10 bits per channel |
| Maximum Sampling Rate | 180 MSPS |
| Analog Supply Voltage | 3.3 V |
| Digital Supply Voltage | 1.8 V |
| Settling Time | 0.015 us |
| Digital Input Interface | Parallel |
| Output Architecture | Current steering |
| Supported Color Spaces | RGB and YPbPr |
| Synchronization Function | Bi-level sync generation |
| Blanking Function | Blanking-level generation |
| Full-Scale Adjustment | Common resistor from FSADJ to AVSS |
| Recommended FSADJ Resistor | 3.8 kilohm for approximately 700 mV output |
| Operating Temperature Range | 0 C to +70 C |
| Package | 48-pin HTQFP (PHP), 7 mm x 7 mm |
| Mounting Type | Surface mount |
THS8136PHP 48-pin htqfp (php), 7 mm x 7 mm Pin Configuration Guide
Pin configuration for THS8136PHP (48-pin htqfp (php), 7 mm x 7 mm package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for THS8136PHP.
Refer to the datasheet for full pin configuration.
Typical Applications
THS8136PHP is suitable for 6 applications: RGB Graphics Card Video Output, YPbPr Component Video Generator, Video Splitter and Distribution, Digital Frame Buffer Video Output, Digital Display Controller, Video Signal Test Equipment.
RGB Graphics Card Video Output
The THS8136PHP fits RGB graphics systems that must convert three parallel 10-bit digital color channels into simultaneous analog red, green, and blue voltages. Its three current-steering DAC channels operate at up to 180 MSPS, matching demanding pixel-clock environments, while the 1.8 V digital supply supports compatible graphics-logic interfaces. Integrated bi-level sync and blanking circuitry can reduce external signal-generation components for RGB systems. The design should route each analog output over a controlled-impedance trace, place the common FSADJ resistor near the device, and preserve continuous ground returns beneath the high-speed digital bus.
Recommended
YPbPr Component Video Generator
The THS8136PHP is appropriate for YPbPr component-video generation because it combines three 10-bit DAC channels with circuitry for bi-level sync and blanking-level generation. Sampling performance is assured to 180 MSPS, allowing the converter to handle high-speed digital component-video data before producing three scaled analog outputs. A 3.8-kilohm FSADJ resistor is suitable for approximately 700 mV full-scale levels in many designs. Engineers should verify cable termination, monitor input impedance, and output scaling while keeping the analog outputs away from switching nodes and noisy digital return paths.
Recommended
Video Splitter and Distribution
A video splitter or distribution board can use the THS8136PHP to regenerate three synchronized analog color outputs from one parallel digital video bus. The 10-bit-per-channel architecture provides consistent quantization across red, green, and blue, while the 180-MSPS capability supports high pixel rates. Because all three channels share the external full-scale adjustment, a single FSADJ resistor establishes their common output scale and simplifies matching. PCB implementation should minimize bus skew, provide solid decoupling near the analog and digital supply pins, and use short analog output routes to prevent loss of video bandwidth.
Recommended
Digital Frame Buffer Video Output
The THS8136PHP is suitable at the output stage of a digital frame buffer or graphics controller that stores raster images and supplies parallel RGB data. Its three integrated 10-bit DACs convert the stored red, green, and blue samples simultaneously at rates up to 180 MSPS, while 3.3 V analog and 1.8 V digital rails support a split supply architecture. The converter reduces the number of discrete output channels required in a compact video engine. Timing alignment, bus skew, output reference stability, and exposed-pad thermal management should be checked together to prevent pixel artifacts.
Recommended
Digital Display Controller
The THS8136PHP can provide the analog color interface for a digital display controller requiring three simultaneous 10-bit channels. Its parallel digital input works well with raster-processing logic, and converter performance is specified through 180 MSPS for high-resolution refresh timing. Integrated sync and blanking generation supports conventional RGB or YPbPr video signaling and can simplify synchronization with downstream display hardware. Layout should treat the digital bus as a high-speed interface, preserve reference-plane continuity, and isolate the analog outputs from clocks and switching regulator nodes.
Recommended
Video Signal Test Equipment
The THS8136PHP is useful in video test equipment that must generate controlled RGB or YPbPr analog outputs from digital test patterns. Three independently addressed 10-bit channels support color-level calibration, while the 180-MSPS operating capability enables high-speed raster stimulus generation. The common FSADJ network makes it straightforward to establish a repeatable full-scale range, and the 3.8-kilohm resistor suits many approximately 700 mV designs. Test-equipment layouts should use stable references, low-noise supply routing, symmetrical output paths, and calibrated terminations to improve channel matching and measurement accuracy.
Recommended
Recommended Products Summary
Engineering reference data for THS8136PHP — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | THS8136IPHP | THS8136PHPR | THS8136IPHPR |
|---|---|---|---|---|
| Package | 48-pin HTQFP (PHP), 7 mm x 7 mm | 48-pin HTQFP (PHP), 7 mm x 7 mm | 48-pin HTQFP (PHP), 7 mm x 7 mm | 48-pin HTQFP (PHP), 7 mm x 7 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Converter Type | Triple video DAC | Triple video DAC | Triple video DAC | Triple video DAC |
| Resolution | 10 bits per channel | 10 bits per channel | 10 bits per channel | 10 bits per channel |
| Maximum Sampling Rate | 180 MSPS | 180 MSPS | 180 MSPS | 180 MSPS |
| Analog Supply | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Digital Supply | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Settling Time | 0.015 us | 0.015 us | 0.015 us | 0.015 us |
| Operating Temperature Range | 0 C to +70 C | Industrial-temperature grade | 0 C to +70 C | Industrial-temperature grade |
| Shipping Format | Tray | Tray | Tape and reel | Tape and reel |
Key Differentiators
- Integrated three-channel video conversion (vs General-purpose single-channel DAC)
- Video-specific synchronization support (vs General-purpose DAC without integrated sync generation)
- Split analog and digital supply architecture (vs Single-supply general-purpose DAC)
Design Notes
Treat the 10-bit parallel input bus as a high-speed interface even though the maximum pixel rate is 180 MSPS. Keep traces short, match the source-to-destination topology, and maintain a continuous reference plane beneath the bus. Place bypass capacitors close to the digital and analog supply pins, and avoid routing video outputs beneath switching nodes or digital clock nets.
Place the FSADJ resistor close to the THS8136PHP and follow the manufacturer’s connection and grounding instructions. A 3.8-kilohm resistor is suitable for many approximately 700 mV output designs, but the final value depends on the required full-scale range and downstream load. Verify the analog return path and keep the adjustment network away from noisy switching currents.
Do not confuse an ordering-format change with an electrical change. THS8136PHP, THS8136PHPR, THS8136IPHP, and THS8136IPHPR retain the same 48-pin HTQFP family, but temperature grade and shipping format differ. Confirm the exact suffix required by the BOM and assembly process, and verify every pin and exposed-pad connection against the manufacturer documentation before substitution.
Compliance Information
The device is a commercial-temperature video DAC and is not identified as an AEC-Q100 automotive-qualified variant. Specific environmental and substance-compliance declarations should be confirmed with the manufacturer before release.