TLV2460CD - 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments
MPN: TLV2460CD ✓ ActiveTLV2460CD Overview
A rail-to-rail input/output operational amplifier is a voltage-feedback amplifier whose input common-mode and output voltage capabilities extend toward the positive and negative supply rails. This rail-to-rail behavior is useful in battery-powered and portable systems where the usable signal range is close to the available supply voltage. The TLV2460 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor.
The TLV2460CD provides one amplifier circuit, 6.4 MHz gain-bandwidth performance, low-power operation, and rail-to-rail input and output characteristics. Its 6 V maximum supply voltage supports low-voltage designs, while the shutdown control can reduce power consumption when the signal chain does not need to remain active. The 8-SOIC package provides a conventional surface-mount format with 0.154-inch body width and 3.90 mm width.
Its 6.4 MHz bandwidth makes the device suitable for general-purpose voltage amplification, buffering, active filtering, and low-to-moderate-frequency signal conditioning. Rail-to-rail input operation permits sensing signals near either supply rail, while rail-to-rail output capability improves usable output range in low-voltage systems. The manufacturer identifies the device as a low-power RRIO amplifier with shutdown for general-purpose instrumentation applications.
Typical uses include portable sensor interfaces, low-voltage analog signal chains, active filters, industrial measurement circuits, and embedded control systems. In a portable sensor interface, the amplifier can condition a sensor signal close to a low-voltage rail. In an active filter, its 6.4 MHz bandwidth provides frequency headroom above the intended passband. The shutdown pin is useful when the amplifier must be disabled during idle periods.
Designers should verify supply range, input common-mode limits, output swing, stability, and shutdown logic for the operating conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because the exact pin names, electrical limits, and capacitor recommendations are not included in the product-page summary, use the manufacturer datasheet for final schematic and layout decisions.
This page organizes the TLV2460CD device information, verified drop-in alternatives, application guidance, package details, and comparison criteria into one engineering-focused reference. It also identifies which technical details require confirmation from the manufacturer datasheet before layout, qualification, or production release.
Drop-in alternatives for TLV2460CD — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
TLV2460AIDR
✅ Drop-In📋 Reference alternative (not in catalog)
TLV2460AIDRG4
✅ Drop-In📋 Reference alternative (not in catalog)
TLV2460CD Maximum Ratings & Electrical Characteristics
| Amplifier Type | Single operational amplifier |
| Number of Channels | 1 circuit |
| Gain-Bandwidth Product | 6.4 MHz |
| Maximum Supply Voltage | 6 V |
| Input Common-Mode Range | Rail-to-rail input |
| Output Swing | Rail-to-rail output |
| Shutdown Support | Yes |
| Power Class | Low-power operational amplifier |
| Technology | LiNCMOS |
| Operating Temperature Range | 0 °C to 70 °C |
| Package Type | 8-SOIC |
| Package Body Width | 0.154 inch (3.90 mm) |
| Number of Pins | 8 pins |
| Mounting Type | Surface mount |
TLV2460CD 0.154 inch (3.90 mm) Pin Configuration Guide
Pin configuration for TLV2460CD (0.154 inch (3.90 mm) package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for TLV2460CD.
Refer to the datasheet for full pin configuration.
Typical Applications
TLV2460CD is suitable for 6 applications: Low-Voltage Sensor Signal Conditioning, Portable Measurement Equipment, Active Filtering and Signal Shaping, Industrial Control and Instrumentation, Battery-Powered Analog Front End, Communications Interface Buffering.
Low-Voltage Sensor Signal Conditioning
The TLV2460CD fits low-voltage sensor interfaces because its rail-to-rail input stage can operate close to the supply rails while the 6.4 MHz gain-bandwidth product provides useful bandwidth for typical sensor signals. Use it to amplify a bridge, potentiometer, or resistive sensor into a higher-level voltage before sampling. The 6 V maximum supply also supports low-voltage analog systems. The key design check is the input bias current and offset against the sensor source impedance; use the manufacturer electrical characteristics to select gain, establish signal headroom, and confirm operation across the required temperature range.
Recommended
Portable Measurement Equipment
The TLV2460CD is appropriate for portable measurement equipment where a single low-voltage amplifier must combine a 6.4 MHz bandwidth with rail-to-rail signal range. It can buffer an analog input or provide gain ahead of an ADC while its shutdown function allows the amplifier to be disabled during inactive intervals. The rail-to-rail output can reduce signal loss in a restricted 5 V supply system. Designers should compare the device supply current with the required battery life, account for shutdown-control overhead, and verify output settling behavior at the selected closed-loop gain and signal bandwidth.
Recommended
Active Filtering and Signal Shaping
The TLV2460CD can implement active filters or waveform-conditioning stages because its 6.4 MHz gain-bandwidth product provides frequency headroom beyond many low-frequency measurement and audio-adjacent passbands. Rail-to-rail input and output behavior is especially useful when filter nodes must operate near a low supply rail. Establish the closed-loop gain and noise gain before selecting capacitors, then evaluate phase margin and component tolerances with the manufacturer’s stability guidance. Decoupling must be placed close to the supply pins, and the shutdown state should remain defined while the filter is not actively used.
Recommended
Industrial Control and Instrumentation
The TLV2460CD can support low-level industrial control and instrumentation circuits that require rail-to-rail sensing and a modest 6 V signal range. It is useful for amplifying sensor outputs or buffering control signals where a high-speed switching reference would add unwanted noise. The 6.4 MHz bandwidth is more than adequate for many slow industrial-control loops, allowing the design to preserve transient response. Confirm the 0 °C to 70 °C temperature rating against enclosure conditions, protect analog traces from switching nodes, and use an appropriate input filter when field wiring introduces interference.
Recommended
Battery-Powered Analog Front End
The TLV2460CD is suitable for a battery-powered analog front end because it is specified as a low-power amplifier with rail-to-rail input and output capability and a maximum supply voltage of 6 V. The shutdown function lets the system disable the amplifier when measurements are not required, helping separate standby demand from active operating demand. The actual energy saving depends on the specified shutdown current and control implementation, which should be taken from the manufacturer datasheet. Validate battery-range behavior, common-mode limits, and startup settling before defining the measurement accuracy.
Recommended
Communications Interface Buffering
The TLV2460CD can serve as a high-speed analog buffer within a low-voltage communications interface, particularly when signal levels occupy much of the available supply range. Its 6.4 MHz gain-bandwidth product supports moderate-frequency conditioning, while the single-channel 8-SOIC format simplifies point-to-point routing. The shutdown control can be coordinated with system activity to reduce power use. Care is required near communication rails because input capacitance, capacitive loading, and output stability determine usable bandwidth. Place the amplifier close to the source or destination it buffers, keep return paths continuous, and test with the actual connector and cable loading.
Recommended
Recommended Products Summary
Engineering reference data for TLV2460CD — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | TLV2460AIDR | TLV2460AIDRG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Number of Amplifiers | 1 | 1 | 1 |
| Gain-Bandwidth Product | 6.4 MHz | 6.4 MHz | 6.4 MHz |
| Maximum Supply Voltage | 6 V | 6 V | 6 V |
| Input Common-Mode Range | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
| Output Swing | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Shutdown Function | Yes | Yes | Yes |
Key Differentiators
- Exact commercial-temperature ordering configuration (vs TLV2460AIDR)
- Single low-power RRIO amplifier with integrated shutdown (vs TLV2460AIDRG4)
- Manufacturer orderable part with explicit 6 V maximum supply (vs TLV2460AIDR)
Design Notes
Decouple the TLV2460CD supply pins with the capacitance specified by the manufacturer for the intended gain and layout. Place the high-frequency bypass capacitor close to the device and keep the return path short to the supply reference. Because shutdown behavior affects system power, define a default state for the shutdown control during reset and power-up. Use the datasheet supply-current and shutdown-current limits when sizing battery capacity; do not infer total power consumption from the 6 V maximum rating alone.
Route the signal input, feedback network, output, and supply connections to minimize parasitic capacitance and resistance. Keep analog inputs away from switching-regulator inductors, high-current return paths, and digital clock lines. For a surface-mount SOIC footprint, follow the manufacturer land-pattern guidance and confirm the pin-1 orientation before fabrication. A short output path is particularly useful when driving capacitive loads because excessive capacitance can reduce stability and alter the practical response below the nominal 6.4 MHz gain-bandwidth product.
Do not treat family similarity as proof of unconditional interchangeability. TLV2460AIDR and TLV2460AIDRG4 differ from TLV2460CD by ordering suffix, which can encode temperature grade or qualification information. Before substituting any candidate, compare the pin table, supply limits, common-mode range, output swing, shutdown logic, electrical characteristics, package drawing, and lifecycle status in the current manufacturer documentation. Also verify that the 0 °C to 70 °C rating of TLV2460CD covers the full intended operating environment.
Choose the closed-loop gain and feedback topology based on the intended signal bandwidth rather than selecting the amplifier only by its 6.4 MHz gain-bandwidth figure. Noise gain affects stability and the effective closed-loop response, while capacitive loading can create peaking or oscillation. For sensor inputs, check bias-current error, offset, and common-mode range under the worst source impedance and supply condition. Add filtering at the input only after accounting for its interaction with capacitance, noise, and the required response time.
Compliance Information
The available manufacturer-page summary does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm all declarations against the current manufacturer product documentation and applicable quality records.