Texas Instruments

TLV2460CD - 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments

MPN: TLV2460CD ✓ Nakahanda
6 V Vdss 8-SOIC Package
MOQ: 1 |

TLV2460CD Ulas

The Texas Instruments TLV2460CD is a single, 6.4 MHz rail-to-rail input/output operational amplifier with shutdown, supplied in an 8-SOIC package. It is designed for low-voltage signal-conditioning systems requiring input and output swing close to the supply rails, a 6 V maximum supply rating, and a shutdown function for controlled power management.

A rail-to-rail input/output operational amplifier is a voltage-feedback amplifier whose input common-mode and output voltage capabilities extend toward the positive and negative supply rails. This rail-to-rail behavior is useful in battery-powered and portable systems where the usable signal range is close to the available supply voltage. The TLV2460 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor.

The TLV2460CD provides one amplifier circuit, 6.4 MHz gain-bandwidth performance, low-power operation, and rail-to-rail input and output characteristics. Its 6 V maximum supply voltage supports low-voltage designs, while the shutdown control can reduce power consumption when the signal chain does not need to remain active. The 8-SOIC package provides a conventional surface-mount format with 0.154-inch body width and 3.90 mm width.

Its 6.4 MHz bandwidth makes the device suitable for general-purpose voltage amplification, buffering, active filtering, and low-to-moderate-frequency signal conditioning. Rail-to-rail input operation permits sensing signals near either supply rail, while rail-to-rail output capability improves usable output range in low-voltage systems. The manufacturer identifies the device as a low-power RRIO amplifier with shutdown for general-purpose instrumentation applications.

Typical uses include portable sensor interfaces, low-voltage analog signal chains, active filters, industrial measurement circuits, and embedded control systems. In a portable sensor interface, the amplifier can condition a sensor signal close to a low-voltage rail. In an active filter, its 6.4 MHz bandwidth provides frequency headroom above the intended passband. The shutdown pin is useful when the amplifier must be disabled during idle periods.

Designers should verify supply range, input common-mode limits, output swing, stability, and shutdown logic for the operating conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because the exact pin names, electrical limits, and capacitor recommendations are not included in the product-page summary, use the manufacturer datasheet for final schematic and layout decisions.

This page organizes the TLV2460CD device information, verified drop-in alternatives, application guidance, package details, and comparison criteria into one engineering-focused reference. It also identifies which technical details require confirmation from the manufacturer datasheet before layout, qualification, or production release.

Mga alternatibo na pwedeng ilagay na TLV2460CD — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

TLV2460AIDR

✅ Drop-In
📦 8-SOIC
Same-family 6.4 MHz RRIO architecture with shutdown; ordering and temperature-grade suffix differ from TLV2460CD.

📋 Alternatibo na Reference (hindi sa katalogo)

TLV2460AIDRG4

✅ Drop-In
📦 8-SOIC
Same-family 6.4 MHz RRIO shutdown amplifier in 8-SOIC; TLV2460CD is specified for 0 °C to 70 °C, while the alternate carries a different temperature/order suffix.

📋 Alternatibo na Reference (hindi sa katalogo)

TLV2460CD Mga Pinakamataas na Rating at Electrical Characteristics

Amplifier Type Single operational amplifier
Number of Channels 1 circuit
Gain-Bandwidth Product 6.4 MHz
Maximum Supply Voltage 6 V
Input Common-Mode Range Rail-to-rail input
Output Swing Rail-to-rail output
Shutdown Support Yes
Power Class Low-power operational amplifier
Technology LiNCMOS
Hanay ng Temperature na Operasyon 0 °C to 70 °C
Package Type 8-SOIC
Package Body Width 0.154 inch (3.90 mm)
Bilang ng Pins 8 pins
Uri ng Pagpapasok Surface mount

Gabay sa Pin Configuration ng TLV2460CD 0.154 inch (3.90 mm)

Pin configuration para sa TLV2460CD (0.154 inch (3.90 mm) package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.

Pinout diagram ng 0.154 inch (3.90 mm) package para sa TLV2460CD

Wala ng detalyadong pinout data na magagamit para sa TLV2460CD.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

TLV2460CD ay nararapat para sa 6 aplikasyons: Low-Voltage Sensor Signal Conditioning, Portable Measurement Equipment, Active Filtering and Signal Shaping, Industrial Control and Instrumentation, Battery-Powered Analog Front End, Communications Interface Buffering.

🧩

Low-Voltage Sensor Signal Conditioning

The TLV2460CD fits low-voltage sensor interfaces because its rail-to-rail input stage can operate close to the supply rails while the 6.4 MHz gain-bandwidth product provides useful bandwidth for typical sensor signals. Use it to amplify a bridge, potentiometer, or resistive sensor into a higher-level voltage before sampling. The 6 V maximum supply also supports low-voltage analog systems. The key design check is the input bias current and offset against the sensor source impedance; use the manufacturer electrical characteristics to select gain, establish signal headroom, and confirm operation across the required temperature range.

📱

Portable Measurement Equipment

The TLV2460CD is appropriate for portable measurement equipment where a single low-voltage amplifier must combine a 6.4 MHz bandwidth with rail-to-rail signal range. It can buffer an analog input or provide gain ahead of an ADC while its shutdown function allows the amplifier to be disabled during inactive intervals. The rail-to-rail output can reduce signal loss in a restricted 5 V supply system. Designers should compare the device supply current with the required battery life, account for shutdown-control overhead, and verify output settling behavior at the selected closed-loop gain and signal bandwidth.

🔧

Active Filtering and Signal Shaping

The TLV2460CD can implement active filters or waveform-conditioning stages because its 6.4 MHz gain-bandwidth product provides frequency headroom beyond many low-frequency measurement and audio-adjacent passbands. Rail-to-rail input and output behavior is especially useful when filter nodes must operate near a low supply rail. Establish the closed-loop gain and noise gain before selecting capacitors, then evaluate phase margin and component tolerances with the manufacturer’s stability guidance. Decoupling must be placed close to the supply pins, and the shutdown state should remain defined while the filter is not actively used.

🏭

Industrial Control and Instrumentation

The TLV2460CD can support low-level industrial control and instrumentation circuits that require rail-to-rail sensing and a modest 6 V signal range. It is useful for amplifying sensor outputs or buffering control signals where a high-speed switching reference would add unwanted noise. The 6.4 MHz bandwidth is more than adequate for many slow industrial-control loops, allowing the design to preserve transient response. Confirm the 0 °C to 70 °C temperature rating against enclosure conditions, protect analog traces from switching nodes, and use an appropriate input filter when field wiring introduces interference.

⚡

Battery-Powered Analog Front End

The TLV2460CD is suitable for a battery-powered analog front end because it is specified as a low-power amplifier with rail-to-rail input and output capability and a maximum supply voltage of 6 V. The shutdown function lets the system disable the amplifier when measurements are not required, helping separate standby demand from active operating demand. The actual energy saving depends on the specified shutdown current and control implementation, which should be taken from the manufacturer datasheet. Validate battery-range behavior, common-mode limits, and startup settling before defining the measurement accuracy.

🌐

Communications Interface Buffering

The TLV2460CD can serve as a high-speed analog buffer within a low-voltage communications interface, particularly when signal levels occupy much of the available supply range. Its 6.4 MHz gain-bandwidth product supports moderate-frequency conditioning, while the single-channel 8-SOIC format simplifies point-to-point routing. The shutdown control can be coordinated with system activity to reduce power use. Care is required near communication rails because input capacitance, capacitive loading, and output stability determine usable bandwidth. Place the amplifier close to the source or destination it buffers, keep return paths continuous, and test with the actual connector and cable loading.

What is the operating voltage of TLV2460CD?
The TLV2460CD supports operation from a low-voltage dual supply up to a 6 V maximum total supply voltage. Texas Instruments describes the device as a single 6 V rail-to-rail input/output operational amplifier with shutdown. The manufacturer part details also identify the 8-SOIC orderable configuration as TLV2460CD, with an operating temperature range from 0 °C to 70 °C. Confirm the minimum and maximum allowable supply conditions in the manufacturer datasheet before applying the amplifier outside a nominal 5 V or ±2.5 V rail.
What is the gain-bandwidth product of TLV2460CD?
The TLV2460CD has a 6.4 MHz gain-bandwidth product. This figure describes the nominal closed-loop bandwidth obtainable with approximately unity noise gain under the manufacturer’s specified test conditions. The bandwidth makes the amplifier suitable for signal conditioning above low audio frequencies, including buffered sensor signals and active-filter stages whose useful passbands remain comfortably below the amplifier’s closed-loop bandwidth. Actual usable bandwidth also depends on gain, noise gain, load, stability configuration, and the exact response specified by Texas Instruments.
What does rail-to-rail input and output mean for TLV2460CD?
Rail-to-rail input and output means the TLV2460CD can accept input common-mode voltages near the supply rails and produce output voltages close to those rails under the specified conditions. This expands the usable signal range in low-voltage systems where conventional non-rail-to-rail amplifiers would clip early. The Texas Instruments product page identifies the TLV2460 as an RRIO amplifier, but designers should consult the datasheet for exact input-range, output-swing, and load-dependent limitations before sizing signal headroom.
Where can I download the TLV2460CD datasheet PDF?
The official TLV2460CD documentation is available from the Texas Instruments product page at https://www.ti.com/product/TLV2460. From that page, engineers can locate the family data sheet, orderable-part information, pin configuration, electrical characteristics, and application guidance. The dedicated orderable-part page for TLV2460CD is available at https://www.ti.com/product/TLV2460/part-details/TLV2460CD. Use the manufacturer copy as the controlling document for package drawings, pin numbering, limits, test conditions, and revision status.
Where can I find the TLV2460CD pinout?
The TLV2460CD pinout is documented in the pin-configuration section of the Texas Instruments TLV2460 family datasheet and in the orderable-part details for the 8-SOIC package. The part uses an 8-SOIC package with 0.154-inch body width and 3.90 mm width. Because the searchable product summary does not reproduce individual terminal names, use the datasheet pin diagram when assigning traces. In particular, confirm the shutdown input, supply terminals, input terminals, output terminal, and any no-connect pins against the package drawing for the selected ordering suffix.
Does TLV2460CD have a shutdown function?
Yes, the TLV2460CD includes a shutdown function. Texas Instruments identifies the TLV2460 family as a low-power rail-to-rail input/output operational amplifier with shutdown. The shutdown control can place the amplifier into a reduced-power state when the circuit does not require continuous amplification, making the device useful in portable and battery-powered equipment. The manufacturer datasheet should be used to confirm the shutdown logic level, operating state, transition timing, and permitted control voltage before finalizing the control circuit.
TLV2460CD vs TLV2460AIDR - which is better for an industrial design?
The TLV2460CD is the 0 °C to 70 °C commercial-temperature orderable part, while the TLV2460AIDR is identified in comparison results as another member of the TLV2460 low-power RRIO family. Both are associated with the same single-amplifier, 6 V, 6.4 MHz architecture, but the temperature grade and ordering suffix must be checked before substitution. For an industrial enclosure with temperatures outside 0 °C to 70 °C, choose the grade explicitly supported for that environment and validate the complete bill of materials before release.
Can TLV2460AIDR replace TLV2460CD without changing the PCB?
TLV2460AIDR can be considered for evaluation as a same-family TLV2460 replacement in an 8-SOIC footprint, but it should not be approved as a drop-in substitute without checking the manufacturer ordering table. The relevant differences include the ordering and temperature-grade suffix, while the TLV2460 family description indicates the same 6 V, 6.4 MHz, rail-to-rail input/output architecture with shutdown. Verify pin functions, electrical limits, qualification grade, and PCB compatibility against the current Texas Instruments datasheet.
What is the best drop-in replacement for TLV2460CD?
The closest documented same-family replacement candidate is TLV2460AIDR because it is compared against TLV2460CD as a single low-power, rail-to-rail input/output amplifier with shutdown. A second candidate, TLV2460AIDRG4, identifies the same electrical description but uses a different ordering suffix. Neither cross-brand replacement is established by the available cross-reference results. Before designating a drop-in replacement, compare the pin configuration, supply range, temperature grade, shutdown behavior, and electrical limits in the manufacturer datasheet.
What can replace TLV2460CD?
TLV2460AIDR is the principal same-family candidate for replacing TLV2460CD because the available comparison identifies both as single low-power rail-to-rail input/output operational amplifiers with shutdown. The second documented candidate is TLV2460AIDRG4, which carries a different ordering suffix. Both should remain conditional until the manufacturer ordering table confirms identical pin functions and operating limits for the intended package. A cross-brand equivalent cannot be recommended from the available results without verified package, pinout, and parametric matching.
When should I choose TLV2460CD instead of TLV2460AIDR?
Choose TLV2460CD when the design requires the exact manufacturer ordering code TLV2460CD, an 8-SOIC package, and the stated 0 °C to 70 °C operating range. Choose TLV2460AIDR only when its ordering suffix and temperature rating better match the production environment and the manufacturer confirms the required electrical and pin compatibility. For a design operating below 0 °C or above 70 °C, neither should be selected solely by family similarity; choose an explicitly temperature-rated orderable part and verify it against the system requirements.
Is TLV2460CD suitable for low-voltage sensor interfaces?
Yes, the TLV2460CD is suitable for many low-voltage sensor-interface stages because it combines rail-to-rail input operation, rail-to-rail output behavior, a 6 V maximum supply voltage, and a 6.4 MHz gain-bandwidth product. These characteristics allow the amplifier to sense and amplify signals occupying much of a low-voltage signal range. The actual sensor excitation, input bias current, offset, noise, output load, and common-mode limits must still be checked against the device electrical characteristics before using it in a precision measurement path.
Where can I buy TLV2460CD and what is its lead time?
Use the Request a Quote form on this page to request current TLV2460CD availability, commercial terms, and lead time. Current inventory and delivery schedules change by order quantity and supply conditions, so engineers should obtain a written quotation for the quantity and package required for production. The Request a Quote form is the appropriate route for sourcing this exact orderable code and for confirming lot traceability, date codes, and scheduled shipment information.
What is the price of TLV2460CD?
Current TLV2460CD commercial pricing should be obtained through the Request a Quote form on this page. The form supports quantity-based quotations for the exact TLV2460CD orderable code and avoids publishing a stale transaction value. Buyers should specify the required quantity, target shipment date, and whether reels, trays, or another approved delivery format are needed. The same request can confirm current stock status, manufacturer lead time, and any lot or date-code requirements.
Is TLV2460CD in stock?
Stock should be confirmed through the Request a Quote form on this page for the exact TLV2460CD ordering code. Distributor listings indicate that the part is marketed for purchase, but inventory levels are time-sensitive and cannot be treated as a guaranteed allocation for a production build. Include your required quantity, delivery date, and approved package format in the request. For safety-critical or high-volume programs, request lot traceability and scheduled delivery terms before committing the component to the BOM.
What are the key specifications of TLV2460CD that engineers should know?
The key TLV2460CD specifications are its single-amplifier configuration, 6 V maximum supply voltage, 6.4 MHz gain-bandwidth product, low-power design, rail-to-rail input and output operation, and shutdown capability. It is packaged in an 8-SOIC measuring 0.154 inches, or 3.90 mm, in body width. Texas Instruments specifies the commercial orderable part for 0 °C to 70 °C. Use the manufacturer datasheet to confirm precision electrical limits, pin names, decoupling guidance, and shutdown timing.

Impormasyon ng Talumpati sa Engineering for TLV2460CD — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose TLV2460CD when the BOM must use the exact Texas Instruments orderable code, the circuit needs a single low-power rail-to-rail input/output amplifier with a 6.4 MHz gain-bandwidth product, and the 8-SOIC package fits the PCB. Its shutdown function is useful when the analog channel must be disabled during idle periods. Consider TLV2460AIDR when its different ordering and temperature-grade suffix better match the production environment, but confirm the exact limits and pin configuration before substitution. TLV2460AIDRG4 is another same-family 8-SOIC candidate with the same documented core architecture, again requiring careful qualification because the suffix may affect environmental or qualification requirements. No cross-brand drop-in candidate is established by the available results, so a different manufacturer should be considered only after package, pinout, supply, bandwidth, shutdown, and electrical-limit compatibility have been independently verified.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto TLV2460AIDR TLV2460AIDRG4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC 8-SOIC
Number of Amplifiers 1 1 1
Gain-Bandwidth Product 6.4 MHz 6.4 MHz 6.4 MHz
Maximum Supply Voltage 6 V 6 V 6 V
Input Common-Mode Range Rail-to-rail input Rail-to-rail input Rail-to-rail input
Output Swing Rail-to-rail output Rail-to-rail output Rail-to-rail output
Shutdown Function Yes Yes Yes

Pangunahing mga Pagkakaiba

  • Exact commercial-temperature ordering configuration (kumpara saTLV2460AIDR)
  • Single low-power RRIO amplifier with integrated shutdown (kumpara saTLV2460AIDRG4)
  • Manufacturer orderable part with explicit 6 V maximum supply (kumpara saTLV2460AIDR)

Talaan ng Disenyo

Decouple the TLV2460CD supply pins with the capacitance specified by the manufacturer for the intended gain and layout. Place the high-frequency bypass capacitor close to the device and keep the return path short to the supply reference. Because shutdown behavior affects system power, define a default state for the shutdown control during reset and power-up. Use the datasheet supply-current and shutdown-current limits when sizing battery capacity; do not infer total power consumption from the 6 V maximum rating alone.

Route the signal input, feedback network, output, and supply connections to minimize parasitic capacitance and resistance. Keep analog inputs away from switching-regulator inductors, high-current return paths, and digital clock lines. For a surface-mount SOIC footprint, follow the manufacturer land-pattern guidance and confirm the pin-1 orientation before fabrication. A short output path is particularly useful when driving capacitive loads because excessive capacitance can reduce stability and alter the practical response below the nominal 6.4 MHz gain-bandwidth product.

Do not treat family similarity as proof of unconditional interchangeability. TLV2460AIDR and TLV2460AIDRG4 differ from TLV2460CD by ordering suffix, which can encode temperature grade or qualification information. Before substituting any candidate, compare the pin table, supply limits, common-mode range, output swing, shutdown logic, electrical characteristics, package drawing, and lifecycle status in the current manufacturer documentation. Also verify that the 0 °C to 70 °C rating of TLV2460CD covers the full intended operating environment.

Choose the closed-loop gain and feedback topology based on the intended signal bandwidth rather than selecting the amplifier only by its 6.4 MHz gain-bandwidth figure. Noise gain affects stability and the effective closed-loop response, while capacitive loading can create peaking or oscillation. For sensor inputs, check bias-current error, offset, and common-mode range under the worst source impedance and supply condition. Add filtering at the input only after accounting for its interaction with capacitance, noise, and the required response time.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The available manufacturer-page summary does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm all declarations against the current manufacturer product documentation and applicable quality records.

Data napatotohanan sa: 2026-11-15 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

TLV2460CD datasheet TLV2460CD datasheet pdf TLV2460CD pinout TLV2460CD SOIC-8 footprint TLV2460CD 6.4MHz specifications TLV2460CD rail to rail op amp TLV2460CD shutdown function TLV2460CD equivalent TLV2460CD replacement TLV2460CD vs TLV2460AIDR Texas Instruments TLV2460CD TLV2460CD price TLV2460CD stock TLV2460CD sensor interface

Mga kaugnay na Mga Komponente at mga Tuntunin

Texas Instruments TLV2460CD TLV2460AIDR TLV2460AIDRG4 operational amplifier analog amplifier voltage-feedback amplifier rail-to-rail input rail-to-rail output RRIO amplifier low-power amplifier shutdown function 6.4 MHz gain-bandwidth product 6 V maximum supply voltage LiNCMOS 8-SOIC SOIC package surface-mount package semiconductor analog signal conditioning active filter sensor interface industrial instrumentation portable measurement equipment
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ