TLV2780ID - 8MHz RRIO Op Amp | TI Signal Conditioning
MPN: TLV2780ID ✓ ActiveTLV2780ID Overview
An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its inverting and non-inverting inputs. It belongs to the voltage-feedback operational-amplifier family and the broader linear and mixed-signal IC hierarchy. Common functions include signal buffering, gain amplification, active filtering, level shifting, current-to-voltage conversion, and feedback control. Rail-to-rail input and output operation, abbreviated RRIO, broadens the usable input and output range in low-voltage systems.
The TLV2780ID combines an 8 MHz gain-bandwidth product with low-bias-current characteristics and shutdown support. These characteristics make it useful for instrumentation, general-purpose amplification, and buffering circuits operating from low-voltage supplies. Shutdown provides a way to control circuit operating state when conserving power is more important than continuous amplification. The manufacturer classifies the TLV2780ID as a general-purpose amplifier, supporting a broad range of analog signal-path requirements.
The device operates down to a 1.8 V supply voltage, while the official product page highlights a 3.6 V operating point and an 8 MHz bandwidth. The TLV278x family provides rail-to-rail input and output capability across the extended industrial temperature range of -40 °C to 125 °C. These figures define the operating envelope for precision control, industrial acquisition, portable instrumentation, and low-voltage embedded analog interfaces where headroom and thermal range are important design constraints.
Typical uses include conditioning outputs from sensors, buffering high-impedance analog stages, amplifying low-level differential signals, and implementing active filters. The low-bias-current characteristic is particularly relevant when the amplifier follows a source with high output impedance, because input bias current can create an offset error across the source impedance. The 8 MHz bandwidth also permits useful closed-loop bandwidth in moderate-gain applications rather than restricting the device to very slow precision-only functions.
Designers should verify the exact input common-mode limits, output swing, shutdown behavior, stability requirements, input bias current, offset voltage, noise, and supply-current limits against the manufacturer datasheet before finalizing a design. Decoupling, output-load stability, grounding, and shutdown-control sequencing should also be reviewed against the recommended application circuit. Those checks are especially important when the amplifier operates near a supply rail, drives a capacitive load, or sources and sinks signals at the limits of its output swing.
This page combines the manufacturer's product information with packaging details, practical application guidance, engineering design notes, and a package-compatible comparison. It is intended to help engineers identify whether the TLV2780ID's low-voltage RRIO performance, 8 MHz bandwidth, low bias current, shutdown function, and 8-pin SOIC implementation fit a particular analog signal-conditioning design.
Drop-in alternatives for TLV2780ID — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
TLV2782AIDR
✅ Drop-In📋 Reference alternative (not in catalog)
TLV2780ID Maximum Ratings & Electrical Characteristics
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 8 MHz |
| Minimum Operating Supply Voltage | 1.8 V |
| Nominal Supply Voltage | 3.6 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Support | Yes |
| Input Bias Current | Low bias current |
| Operating Temperature Range | -40 °C to 125 °C |
| Package | 8-pin SOIC |
| Mounting Type | Surface mount |
| Number of Pins | 8 pins |
| Product Classification | Standard general-purpose amplifier |
TLV2780ID 8-pin soic Pin Configuration Guide
Pin configuration for TLV2780ID (8-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for TLV2780ID.
Refer to the datasheet for full pin configuration.
Typical Applications
TLV2780ID is suitable for 6 applications: Low-Voltage Sensor Signal Conditioning, Precision Instrumentation Buffering, Active Filter and Frequency Response Design, Industrial Control Signal Interface, Portable and Embedded Analog Interfaces, Level Shifting and Output Drive.
Low-Voltage Sensor Signal Conditioning
The TLV2780ID fits low-voltage sensor front ends that need input and output operation close to the supply rails. Its 1.8 V minimum supply and rail-to-rail input are useful when sensor signals occupy much of the available signal range. The low-bias-current characteristic helps limit input-referred error when the sensor source impedance is high. An 8 MHz gain-bandwidth product also permits useful closed-loop response in moderate-gain conditioning stages. The design should still calculate source-impedance error and confirm common-mode headroom against the datasheet limits.
Recommended
Precision Instrumentation Buffering
The TLV2780ID can buffer instrumentation signals when a high-impedance source must drive a later measurement or control stage. Low bias current is the primary benefit because the amplifier input current interacts with source resistance and can generate unwanted voltage error. The rail-to-rail input and output characteristics preserve signal span in compact 1.8 V and 3.6 V systems. The 8 MHz bandwidth provides more closed-loop capability than a very slow general-purpose buffer. Use the manufacturer recommended operating region and check the source capacitance before finalizing the buffer configuration.
Recommended
Active Filter and Frequency Response Design
The TLV2780ID is suitable for active analog filters whose signal bandwidth is compatible with its 8 MHz gain-bandwidth product. Rail-to-rail input and output are advantageous when the filter processes small signals near the supply limits, while the low-bias-current characteristic helps preserve accuracy with high-impedance sources. Designers should select resistor and capacitor values using the required noise gain and verify stability at each stage. Because the 8 MHz figure describes gain-bandwidth product rather than guaranteed flat closed-loop bandwidth, the complete filter response must be evaluated with the selected topology.
Recommended
Industrial Control Signal Interface
The TLV2780ID supports low-level analog signal interfaces in industrial equipment operating across the extended -40 °C to 125 °C temperature range. Its 1.8 V minimum supply can simplify low-voltage front ends, and the rail-to-rail input and output provide useful signal headroom. The shutdown function can reduce consumption when a subsystem is inactive. For an industrial design, verify supply tolerance, shutdown sequencing, output drive, and channel behavior throughout the intended temperature range. Surface-mount 8-pin SOIC packaging supports compact controller boards while simplifying assembly and inspection.
Recommended
Portable and Embedded Analog Interfaces
The TLV2780ID fits portable and embedded systems that combine a low-voltage supply with limited analog signal headroom. Operation from a 1.8 V minimum supply reduces the need for a higher-voltage analog rail, while rail-to-rail input and output maximize usable range within that supply. The shutdown function supports power management when the analog path is not continuously needed. In a compact design, place the device near the signal source, use a low-noise supply path, and verify the shutdown state before powering downstream circuitry. Thermal performance is generally manageable at low supply voltages, but final dissipation depends on the actual operating current.
Recommended
Level Shifting and Output Drive
The TLV2780ID can perform level shifting between low-voltage analog domains because its output is specified as rail-to-rail. The single-amplifier configuration makes it useful for shifting a bipolar or single-ended signal into the input range of a downstream converter or controller. Rail-to-rail input support allows operation close to the negative and positive supply limits, but exact input and output limits depend on supply voltage and load. Verify the direction of the level shift, allowed input range, output swing, and load capacitance. The shutdown control should also be sequenced so the downstream device is not exposed to an unexpected output state.
Recommended
Recommended Products Summary
Engineering reference data for TLV2780ID — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | TLV2782AIDR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC |
| Shutdown or Control Function | Shutdown | Related family control configuration; exact behavior requires datasheet confirmation |
Key Differentiators
- Single 8 MHz RRIO amplifier with shutdown (vs TLV2782AIDR)
- Low-voltage analog headroom (vs TLV2782AIDR)
- Extended industrial temperature operation (vs TLV2782AIDR)
Design Notes
Verify the shutdown pin polarity and its effect on output state before connecting the control signal. A rail-to-rail input range does not mean that every input condition is acceptable at every supply voltage. Use the manufacturer's pin-description table, common-mode limits, and recommended application circuit, and ensure the control signal itself remains within the device's input limits when shutdown is asserted.
Place the amplifier close to the signal source and place its bypass capacitor at the supply pins using the shortest practical return path. Keep sensitive input nodes away from switching nodes and high-current return paths. Because the TLV2780ID supports low bias current and rail-to-rail inputs, PCB leakage and contamination can become significant in high-impedance instrumentation; clean boards and suitable guard or shielding techniques may matter more than ordinary low-frequency layout.
Treat the 8 MHz gain-bandwidth product as a closed-loop design limit rather than a guaranteed signal passband. Select noise gain according to the required stability and bandwidth, and evaluate capacitive loading at the output. If driving long cables, ADC inputs, or capacitive loads, use the manufacturer's stability information or isolate the amplifier with an appropriate resistor. Also confirm that the operating point remains inside the specified input common-mode range.
Compliance Information
The manufacturer product page and family documentation do not state the requested compliance statuses in the cited material. AEC-Q100 qualification is not indicated for the standard TLV2780ID.