TS321IDT - 30V Single 800kHz Op Amp | STMicroelectronics
MPN: TS321IDT ✗ End of LifeTS321IDT Overview
An operational amplifier is an active analog component that uses high-gain differential feedback to amplify the difference between two input voltages. Within the product hierarchy, the TS321IDT is a general-purpose operational amplifier, a bipolar linear amplifier, and a member of the broader analog IC and semiconductor families. Its role is to increase signal amplitude while maintaining the closed-loop behavior established by external resistors or feedback networks.
Key characteristics include the single-amplifier configuration, 800 kHz bandwidth, and 30 V maximum supply voltage. The manufacturer describes the device as a bipolar operational amplifier intended for compact, cost-sensitive designs. Its performance approach is intended to match or better selected industry-standard devices such as the LM358A and LM324 families, providing a familiar general-purpose solution without requiring a high-speed or precision-amplifier architecture.
The TS321IDT operates from a dual supply extending to plus or minus 15 V, equivalent to a maximum total supply of 30 V. Its single-amplifier organization makes it appropriate when the PCB does not justify a dual or quad amplifier. Because it is a bipolar part rather than a CMOS amplifier, engineers should pay particular attention to input bias current, offset behavior, common-mode range, and output-swing limits during precision signal-chain design.
Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, gain stages in measurement systems, and general industrial signal conditioning. It is particularly useful in compact equipment where an 8-pin SOIC footprint provides more mechanical flexibility than a small-outline package while maintaining low cost and straightforward PCB assembly.
When laying out a TS321IDT circuit, place input, output, and decoupling connections according to the manufacturer pin-description table and keep feedback resistors close to the amplifier where practical. Confirm the required input common-mode voltage and output swing against the actual signal range. Stable operation also depends on suitable output loading and the compensation or feedback network selected for the intended gain.
This page combines manufacturer and distributor information with an obsolete-lifecycle assessment, same-footprint alternatives, application guidance, and design considerations. It helps engineers distinguish a genuine circuit-compatible replacement from a merely similar single amplifier before committing a redesign to an active device.
Drop-in alternatives for TS321IDT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with TS321IDT (same form factor and footprint) — differing in Package, Number of Channels, Product Type.
TS321ID
✅ Drop-InContact for price
View Datasheet →TLV9301IDBVR
✅ Drop-InContact for price
View Datasheet →TL031CDR
✅ Drop-In📋 Reference alternative (not in catalog)
TS321IDT Maximum Ratings & Electrical Characteristics
| Product Type | Single general-purpose operational amplifier |
| Amplifier Architecture | Bipolar operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 800 kHz |
| Maximum Total Supply Voltage | 30 V |
| Nominal Supply Configuration | Plus or minus 15 V |
| Package | 8-pin SOIC |
| Mounting Type | Surface mount |
TS321IDT 8-pin soic Pin Configuration Guide
Pin configuration for TS321IDT (8-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for TS321IDT.
Refer to the datasheet for full pin configuration.
Typical Applications
TS321IDT is suitable for 6 applications: Industrial Sensor Signal Conditioning, Measurement and Instrumentation Front Ends, Active Filtering and Gain Stages, Power Supply and Control Monitoring, Audio and Communication Interface Circuits, Legacy Equipment Maintenance.
Industrial Sensor Signal Conditioning
The TS321IDT can condition low-level sensor signals in industrial equipment when the source operates within the amplifier's input common-mode range. Its single bipolar channel is useful for buffering, gain adjustment, or active-filter functions where a dual or quad amplifier would leave unused circuitry. The 800 kHz gain-bandwidth product supports modest-bandwidth measurements, while the 30 V total supply rating accommodates plus or minus 15 V analog rails. Engineers should calculate the closed-loop gain against bandwidth, verify output swing, and assess the sensor's source impedance because bipolar input bias current can affect high-impedance sources.
Recommended
Measurement and Instrumentation Front Ends
The TS321IDT is suited to low-frequency measurement front ends that require a compact, single-channel general-purpose amplifier. It can amplify a bridge-derived or buffered sensor signal, add gain around a transducer, or drive the input of a subsequent converter. Its 800 kHz gain-bandwidth product is appropriate for many instrumentation channels that do not require high-frequency precision, and the 30 V supply limit supports laboratory and industrial rails. The circuit must maintain the input and output inside the common-mode and swing limits defined by the manufacturer datasheet, with particular attention to offset and bias-current requirements.
Recommended
Active Filtering and Gain Stages
The TS321IDT can implement an active low-pass filter, inverting stage, or non-inverting gain block when component count and PCB area are important. A single SOIC-8 amplifier allows a feedback network to be placed close to the device, reducing parasitic effects in moderate-frequency designs. The 800 kHz gain-bandwidth product should be compared with the desired closed-loop gain and phase margin, while the output load must remain within the device's drive capability. Because the TS321IDT is obsolete, an existing filter should preserve its network values and verify an active replacement's stability and output behavior before production release.
Recommended
Power Supply and Control Monitoring
The TS321IDT can amplify a scaled voltage from a power-supply or industrial control circuit when a dedicated precision amplifier is unnecessary. A resistive divider can bring the monitored level into the amplifier's input common-mode range, after which closed-loop feedback establishes the required gain. Its plus or minus 15 V capability is useful in equipment that already uses bipolar analog rails. The key design checks are the input offset at the monitored level, output headroom during fault conditions, and whether the loop remains stable at the selected gain. An active replacement should be preferred for newly designed monitoring systems.
Recommended
Audio and Communication Interface Circuits
The TS321IDT can be used in low-frequency audio or communications interface paths where a compact, economical single amplifier is sufficient. It may buffer a line-level signal, provide modest voltage gain, or form part of an active equalizer and filtering network. The 800 kHz gain-bandwidth product covers a substantial audio-band application while remaining modest compared with modern high-speed amplifiers. Designers should calculate the required gain, check headroom for the largest expected waveform, and confirm that the input bias current does not excessively load the source. Existing audio boards should validate an obsolete-status replacement for channel-to-channel behavioral differences.
Recommended
Legacy Equipment Maintenance
The TS321IDT is most appropriate for maintaining an existing piece of industrial or test equipment whose circuit has already been qualified around the original amplifier. Its 800 kHz bandwidth, 30 V supply capability, and single-channel organization allow a direct circuit-level comparison with the installed device. Since the STMicroelectronics part is obsolete, use the original schematic, manufacturer pin table, and electrical-characteristics data to verify any substitute before installation. Legacy maintenance also requires attention to traceability, storage, soldering practices, and the possibility that the amplifier is no longer the only obsolete component in the assembly.
Recommended
Recommended Products Summary
Engineering reference data for TS321IDT — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | TS321ID | TLV9301 | TL031CDR |
|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 1 channel | 1 channel | 1 channel | 1 channel |
| Product Class | General-purpose operational amplifier | General-purpose operational amplifier | Low-power operational amplifier | General-purpose operational amplifier |
Key Differentiators
- Direct 800 kHz and 30 V functional baseline (vs TS321ID)
- Higher-voltage active upgrade path (vs TLV9301)
- Single-channel SOIC-8 implementation (vs TL031CDR)
Design Notes
Do not treat identical package dimensions as proof of electrical interchangeability. Before replacing the TS321IDT, compare the manufacturer pin-description table, input common-mode range, output swing, input offset, input bias current, supply current, gain-bandwidth product, and stability behavior. The TL031CDR uses the same 8-pin SOIC footprint but has different internal characteristics, while the TLV9301 offers higher voltage and bandwidth ratings. Preserve the original feedback and compensation network until the revised circuit has been verified.
Keep feedback resistors and compensation components close to the amplifier, and route the inverting input with a short, low-leakage trace to reduce parasitic capacitance and noise pickup. Place the device ground connection directly into the quiet analog-ground system rather than forcing return current through a long loop beneath noisy switching nodes. Because the TS321IDT is a bipolar amplifier, high-impedance input traces can be affected by bias current and surface leakage; guard techniques may be useful when the source resistance is very high.
The 30 V rating is the total voltage between the positive and negative supply terminals, not permission to apply 30 V to either rail. Include startup and transient headroom when selecting supply rails, and add local supply bypassing with the capacitance and placement specified by the manufacturer. Check output-current demand against the device's load capability and verify that the feedback network does not pull the output into an unsupported region during saturation or shutdown.
Because the STMicroelectronics TS321IDT is obsolete, sourcing controls matter as much as electrical matching. Specify the exact MPN and package, request lot or traceability information where available, and define inspection requirements before approval. Avoid mixing the TS321IDT with another manufacturer's TS321 designation without verifying its temperature range, qualification status, documentation, and lifecycle. For new production, use the Request a Quote form to coordinate an active replacement and avoid extending dependence on legacy stock.
Compliance Information
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact TS321IDT ordering suffix. The device is an obsolete general-purpose operational amplifier rather than an automotive-qualified part.