TS3704IN - 4-Channel Micropower CMOS Comparator | STMicroelectronics
MPN: TS3704IN ✓ ActiveTS3704IN Overview
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its digital output state when one input exceeds the other. This places the TS3704IN within the hierarchy of comparator IC, analog interface IC, and semiconductor. Four independent channels in one package reduce board area in threshold detection, window comparison, sensor conditioning, and control systems where several voltage relationships must be monitored.
Key features include a push-pull CMOS output stage that eliminates the external pull-up resistor required by open-collector comparators. The typical input offset voltage is 5 mV, typical input bias current is 600 pA, and the response time is approximately 2 µs for a 5 mV overdrive. A nominal supply voltage of 3 V and an operating temperature range from -40 °C to +125 °C support both portable and industrial designs.
The CMOS input stage provides high input impedance, helping the TS3704IN interface with high-impedance sensors without drawing substantial signal current. Its four-channel architecture also simplifies power sequencing because all comparators operate from the same supply. The push-pull output can actively drive both high and low states, although designers must account for the output current and voltage limits specified by the manufacturer when connecting loads.
Typical uses include battery-powered threshold detection, industrial sensor interfaces, window comparators, overvoltage monitoring, control-system logic, and four-channel signal conditioning. In portable equipment, the 9 µA typical consumption per comparator is especially useful. For longer trace runs or noisy industrial environments, input filtering and careful grounding remain necessary even though the push-pull output reduces dependence on external pull-up hardware.
PCB layout should keep input and output traces short, provide a stable ground reference, and place input filtering close to the comparator inputs. Because all four channels share supply pins, bypassing the supply close to the package helps minimize disturbance between channels. Avoid relying on the comparator output for functions requiring a pull-up resistor, since the TS3704IN output architecture is push-pull rather than open collector.
This product page combines the manufacturer’s electrical characteristics, package and pin information, verified distributor listings, application guidance, and a strictly same-package alternative assessment. It is intended to help engineers determine whether the TS3704IN’s four channels, low current consumption, input impedance, and output architecture fit a specific low-power design.
Drop-in alternatives for TS3704IN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
TS3704ID
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →TS3704IN Maximum Ratings & Electrical Characteristics
| Comparator Type | 4-channel general-purpose voltage comparator |
| Number of Channels | 4 channels |
| Technology | CMOS |
| Output Type | Push-pull CMOS |
| Typical Supply Current | 9 µA per comparator |
| Nominal Supply Voltage | 3 V |
| Maximum Supply Voltage | 16 V |
| Input Voltage Range | ±8 V |
| Typical Input Offset Voltage | 5 mV |
| Typical Input Bias Current | 600 pA |
| Typical Response Time | 2 µs at 5 mV overdrive |
| Input Impedance | 10^12 Ω typical |
| Operating Temperature Range | -40 °C to +125 °C |
| Package | 14-pin PDIP |
| Mounting Type | Through-hole |
| External Pull-Up Resistor | Not required for push-pull outputs |
TS3704IN Pin Configuration
| Pin 1 | OUT1 — Comparator 1 push-pull output |
| Pin 2 | IN1- — Comparator 1 inverting input |
| Pin 3 | IN1+ — Comparator 1 non-inverting input |
| Pin 4 | VCC — Positive supply voltage |
| Pin 5 | IN2+ — Comparator 2 non-inverting input |
| Pin 6 | IN2- — Comparator 2 inverting input |
| Pin 7 | OUT2 — Comparator 2 push-pull output |
| Pin 8 | OUT3 — Comparator 3 push-pull output |
| Pin 9 | IN3- — Comparator 3 inverting input |
| Pin 10 | IN3+ — Comparator 3 non-inverting input |
| Pin 11 | GND — Ground reference |
| Pin 12 | IN4+ — Comparator 4 non-inverting input |
| Pin 13 | IN4- — Comparator 4 inverting input |
| Pin 14 | OUT4 — Comparator 4 push-pull output |
Typical Applications
TS3704IN is suitable for 6 applications: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Battery Overvoltage Monitoring, Window Voltage Comparator, Control-System Logic Interfacing, Precision Level and Limit Detection.
Battery-Powered Threshold Detection
The TS3704IN is suitable for portable equipment that must monitor several battery or signal thresholds without allocating a separate comparator IC to each function. Its typical 9 µA consumption per comparator limits the current attributable to the comparison channels, while the 3 V nominal supply supports low-voltage systems. Four push-pull channels can report discrete state changes to a microcontroller or low-power controller. The principal design consideration is ensuring that every input and output remains inside the ratings stated in the manufacturer datasheet, especially during battery transitions and transients.
Recommended
Industrial Sensor Signal Conditioning
The TS3704IN can convert slow or high-impedance sensor signals into digital decisions for industrial control equipment. Its CMOS input stage has a typical input bias current of 600 pA and input impedance of 10^12 Ω, helping avoid significant loading on sensitive sensing networks. The typical 5 mV offset and approximately 2 µs response at 5 mV overdrive support threshold decisions where response and accuracy must be balanced. Designers should add filtering appropriate to the sensor's noise characteristics and route comparator inputs away from high-current switching paths.
Recommended
Battery Overvoltage Monitoring
Four TS3704IN channels can monitor multiple battery-cell or power-rail conditions within a compact monitoring circuit. The comparator family operates from a 3 V nominal supply and accepts input voltages up to ±8 V, allowing suitably scaled cell voltages to be compared against references. Push-pull outputs provide a defined logic state without external pull-up resistors, simplifying connection to monitoring logic. In a practical implementation, reference selection, input divider tolerances, and the maximum input ratings must be evaluated for worst-case battery voltage and temperature conditions.
Recommended
Window Voltage Comparator
The TS3704IN can implement two upper-and-lower threshold windows by assigning two channels to each monitored voltage. The TS3704 family provides approximately 2 µs response at 5 mV overdrive, making the comparators useful for signals that change without requiring continuous high-speed data conversion. The push-pull outputs simplify interfacing with logic gates or a controller, but system designers must define how the two channel states are combined and must account for reference-node errors when interpreting the measured window. Input filtering should preserve the intended detection speed.
Recommended
Control-System Logic Interfacing
The TS3704IN is appropriate for comparing a feedback or status voltage with a reference before driving control logic in a feedback system. Four channels allow multiple supervisory decisions to be packaged together, while the low typical current of 9 µA per comparator is useful in distributed sensing systems. The push-pull output stage reduces the component count normally associated with open-collector comparators. Designers should verify output loading, establish a low-impedance ground reference, and account for the 5 mV typical input offset when choosing a threshold margin for critical control functions.
Recommended
Precision Level and Limit Detection
The TS3704IN can generate limit flags when an analog node crosses a defined reference level. Its typical input offset of 5 mV provides a basis for precision decisions in measurement and instrumentation systems, while high input impedance limits loading of the source being observed. The 2 µs typical response at 5 mV overdrive supports prompt detection of moderate changes without the continuous activity of a general-purpose converter. Calibration may be necessary when offset and reference drift materially affect the desired trip point, and critical thresholds should include appropriate hysteresis to prevent repeated switching.
Recommended
Recommended Products Summary
Engineering reference data for TS3704IN — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | TS3704ID |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 14-pin PDIP | 14-pin PDIP |
| Number of Channels | 4 channels | 4 channels |
| Comparator Technology | CMOS | CMOS |
| Output Type | Push-pull CMOS | Push-pull CMOS |
| Typical Supply Current | 9 µA per comparator | 9 µA per comparator |
| Nominal Supply Voltage | 3 V | 3 V |
| Maximum Supply Voltage | 16 V | 16 V |
| Input Voltage Range | ±8 V | ±8 V |
| Typical Input Offset Voltage | 5 mV | 5 mV |
| Typical Response Time | 2 µs at 5 mV overdrive | 2 µs at 5 mV overdrive |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C |
Key Differentiators
- Four complete comparison channels in one package (vs TS3704ID)
- Push-pull output architecture (vs TS3704ID)
- Low-power CMOS operation (vs TS3704ID)
Design Notes
Place the supply bypass capacitor close to the TS3704IN VCC pin and connect it to a low-impedance ground path. Because all four comparators share the same package, inadequate supply bypassing can couple disturbance from one switching channel into another. Route the high-impedance input nets away from output and switching-node traces, and use a continuous ground plane where practical.
The CMOS inputs provide high impedance, but they can still pick up noise when connected to long PCB traces or nearby switching circuitry. Add input-series resistance and capacitance only after checking their effect on response time. The manufacturer lists approximately 2 µs typical response at 5 mV overdrive; excessive filtering or a slow source impedance can lengthen the practical decision time.
Do not substitute an open-collector LM339 directly and assume identical output behavior. The manufacturer describes the TS3704 as pin-to-pin and functionally compatible with the LM339, but the TS3704 uses push-pull outputs while the LM339 requires an external pull-up resistor. Review the original PCB for pull-up networks, output load current, input polarity, and logic direction before approving a cross-family replacement.
Budget the comparator current as approximately 9 µA per channel, then include supply current from the complete TS3704IN device and any external logic. The nominal 3 V operating point does not guarantee that all inputs and outputs remain within their limits at every rail condition. Design protection around the maximum 16 V supply rating and ±8 V input range stated in the manufacturer datasheet.
Compliance Information
The manufacturer datasheet describes the TS3704 family, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not established for the TS3704IN.