STMicroelectronics

TS3704IN - 4-Channel Micropower CMOS Comparator | STMicroelectronics

Teilenummer: TS3704IN ✓ Aktiv
9 µA per comparator Vdss 600 pA Id 14-pin PDIP Package
MOQ: 1 |

TS3704IN Übersicht

The STMicroelectronics TS3704IN is a micropower quad CMOS voltage comparator with four independent comparison channels, push-pull outputs, and a 14-pin PDIP package. Each comparator typically consumes 9 µA, while the complete device is designed for low-power signal conditioning. According to the manufacturer datasheet, the TS3704IN supports input voltages up to ±8 V with a nominal 16 V supply and accepts a single supply from 3 V.

A voltage comparator is an analog integrated circuit that compares two input voltages and changes its digital output state when one input exceeds the other. This places the TS3704IN within the hierarchy of comparator IC, analog interface IC, and semiconductor. Four independent channels in one package reduce board area in threshold detection, window comparison, sensor conditioning, and control systems where several voltage relationships must be monitored.

Key features include a push-pull CMOS output stage that eliminates the external pull-up resistor required by open-collector comparators. The typical input offset voltage is 5 mV, typical input bias current is 600 pA, and the response time is approximately 2 µs for a 5 mV overdrive. A nominal supply voltage of 3 V and an operating temperature range from -40 °C to +125 °C support both portable and industrial designs.

The CMOS input stage provides high input impedance, helping the TS3704IN interface with high-impedance sensors without drawing substantial signal current. Its four-channel architecture also simplifies power sequencing because all comparators operate from the same supply. The push-pull output can actively drive both high and low states, although designers must account for the output current and voltage limits specified by the manufacturer when connecting loads.

Typical uses include battery-powered threshold detection, industrial sensor interfaces, window comparators, overvoltage monitoring, control-system logic, and four-channel signal conditioning. In portable equipment, the 9 µA typical consumption per comparator is especially useful. For longer trace runs or noisy industrial environments, input filtering and careful grounding remain necessary even though the push-pull output reduces dependence on external pull-up hardware.

PCB layout should keep input and output traces short, provide a stable ground reference, and place input filtering close to the comparator inputs. Because all four channels share supply pins, bypassing the supply close to the package helps minimize disturbance between channels. Avoid relying on the comparator output for functions requiring a pull-up resistor, since the TS3704IN output architecture is push-pull rather than open collector.

This product page combines the manufacturer’s electrical characteristics, package and pin information, verified distributor listings, application guidance, and a strictly same-package alternative assessment. It is intended to help engineers determine whether the TS3704IN’s four channels, low current consumption, input impedance, and output architecture fit a specific low-power design.

Drop-in-Alternativen für TS3704IN – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

TS3704ID

✅ Drop-In ⚠️ Spezifikationen ungeprüft
STMicroelectronics
📦 14-pin PDIP
General-purpose quad voltage comparator · 4 channels · 9 uA typical · 1 TOhm typical · 0.0006 uA · 6500 uV · 2 us typical for a 5 mV step · Push-pull CMOS

Preis auf Anfrage

Datenblatt ansehen →

TS3704IN Grenzwerte & elektrische Eigenschaften

Comparator Type 4-channel general-purpose voltage comparator
Number of Channels 4 channels
Technology CMOS
Ausgangstyp Push-pull CMOS
Typical Supply Current 9 µA per comparator
Nominal Supply Voltage 3 V
Maximum Supply Voltage 16 V
Eingangsspannungsbereich ±8 V
Typical Input Offset Voltage 5 mV
Typical Input Bias Current 600 pA
Typical Response Time 2 µs at 5 mV overdrive
Input Impedance 10^12 Ω typical
Betriebstemperaturbereich -40 °C to +125 °C
Gehäuse 14-pin PDIP
Montageart Through-hole
External Pull-Up Resistor Not required for push-pull outputs

TS3704IN Pin-Konfiguration

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
Pin 1 OUT1 — Comparator 1 push-pull output
Pin 2 IN1- — Comparator 1 inverting input
Pin 3 IN1+ — Comparator 1 non-inverting input
Pin 4 VCC — Positive supply voltage
Pin 5 IN2+ — Comparator 2 non-inverting input
Pin 6 IN2- — Comparator 2 inverting input
Pin 7 OUT2 — Comparator 2 push-pull output
Pin 8 OUT3 — Comparator 3 push-pull output
Pin 9 IN3- — Comparator 3 inverting input
Pin 10 IN3+ — Comparator 3 non-inverting input
Pin 11 GND — Ground reference
Pin 12 IN4+ — Comparator 4 non-inverting input
Pin 13 IN4- — Comparator 4 inverting input
Pin 14 OUT4 — Comparator 4 push-pull output

Typische Anwendungen

TS3704IN ist geeignet für 6 Anwendungs: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Battery Overvoltage Monitoring, Window Voltage Comparator, Control-System Logic Interfacing, Precision Level and Limit Detection.

📱

Battery-Powered Threshold Detection

The TS3704IN is suitable for portable equipment that must monitor several battery or signal thresholds without allocating a separate comparator IC to each function. Its typical 9 µA consumption per comparator limits the current attributable to the comparison channels, while the 3 V nominal supply supports low-voltage systems. Four push-pull channels can report discrete state changes to a microcontroller or low-power controller. The principal design consideration is ensuring that every input and output remains inside the ratings stated in the manufacturer datasheet, especially during battery transitions and transients.

🏭

Industrial Sensor Signal Conditioning

The TS3704IN can convert slow or high-impedance sensor signals into digital decisions for industrial control equipment. Its CMOS input stage has a typical input bias current of 600 pA and input impedance of 10^12 Ω, helping avoid significant loading on sensitive sensing networks. The typical 5 mV offset and approximately 2 µs response at 5 mV overdrive support threshold decisions where response and accuracy must be balanced. Designers should add filtering appropriate to the sensor's noise characteristics and route comparator inputs away from high-current switching paths.

⚡

Battery Overvoltage Monitoring

Four TS3704IN channels can monitor multiple battery-cell or power-rail conditions within a compact monitoring circuit. The comparator family operates from a 3 V nominal supply and accepts input voltages up to ±8 V, allowing suitably scaled cell voltages to be compared against references. Push-pull outputs provide a defined logic state without external pull-up resistors, simplifying connection to monitoring logic. In a practical implementation, reference selection, input divider tolerances, and the maximum input ratings must be evaluated for worst-case battery voltage and temperature conditions.

🔧

Window Voltage Comparator

The TS3704IN can implement two upper-and-lower threshold windows by assigning two channels to each monitored voltage. The TS3704 family provides approximately 2 µs response at 5 mV overdrive, making the comparators useful for signals that change without requiring continuous high-speed data conversion. The push-pull outputs simplify interfacing with logic gates or a controller, but system designers must define how the two channel states are combined and must account for reference-node errors when interpreting the measured window. Input filtering should preserve the intended detection speed.

🖥️

Control-System Logic Interfacing

The TS3704IN is appropriate for comparing a feedback or status voltage with a reference before driving control logic in a feedback system. Four channels allow multiple supervisory decisions to be packaged together, while the low typical current of 9 µA per comparator is useful in distributed sensing systems. The push-pull output stage reduces the component count normally associated with open-collector comparators. Designers should verify output loading, establish a low-impedance ground reference, and account for the 5 mV typical input offset when choosing a threshold margin for critical control functions.

📟

Precision Level and Limit Detection

The TS3704IN can generate limit flags when an analog node crosses a defined reference level. Its typical input offset of 5 mV provides a basis for precision decisions in measurement and instrumentation systems, while high input impedance limits loading of the source being observed. The 2 µs typical response at 5 mV overdrive supports prompt detection of moderate changes without the continuous activity of a general-purpose converter. Calibration may be necessary when offset and reference drift materially affect the desired trip point, and critical thresholds should include appropriate hysteresis to prevent repeated switching.

Zusammenfassung der empfohlenen Produkte

TS3704CDT Same TS3704 comparator family for surface-mount designs Verwendet in: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Battery Overvoltage Monitoring, Window Voltage Comparator, Control-System Logic Interfacing, Precision Level and Limit Detection TS3704IPT Same TS3704 comparator family in a compact surface-mount package Verwendet in: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Battery Overvoltage Monitoring, Window Voltage Comparator, Control-System Logic Interfacing, Precision Level and Limit Detection
What is the TS3704IN and what does it do?
The TS3704IN is a four-channel micropower CMOS voltage comparator from STMicroelectronics. Each channel compares two analog input voltages and provides a push-pull digital output, allowing threshold, window, and level detection in one 14-pin PDIP package. According to the manufacturer datasheet, typical consumption is 9 µA per comparator, and the push-pull outputs eliminate the external pull-up resistor normally required with open-collector comparators.
What is the operating voltage of TS3704IN?
The TS3704IN operates from a single 3 V nominal supply, with a maximum listed supply voltage of 16 V and an input voltage range of ±8 V. The manufacturer datasheet identifies the TS3704 as a micropower CMOS quad voltage comparator. Its low-voltage operation makes it suitable for portable equipment and low-voltage industrial control systems, subject to the complete input and output voltage limits.
How much current does each TS3704IN comparator consume?
Each TS3704IN comparator typically consumes 9 µA according to the STMicroelectronics manufacturer datasheet. This is described as approximately 20 times lower consumption than a bipolar LM339 comparator. The four channels share a common package and supply arrangement, allowing a design to obtain multiple comparison functions without using four separate comparator ICs.
What is the TS3704IN pinout?
The TS3704IN uses a 14-pin PDIP arrangement containing four complete comparator channels. Pins 1 through 7 form comparator 1 and comparator 2, pins 8 through 11 form comparator 3, and pins 12 through 14 complete comparator 4, with supply and ground connections distributed through the package. Use the pin-description table and package drawing in the manufacturer datasheet when assigning PCB nets.
Where can I download the TS3704IN datasheet PDF?
The official TS3704IN datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/ts3704.pdf. The document describes the micropower quad CMOS voltage comparator and is the authoritative source for the electrical characteristics, pin assignments, typical application circuits, and package dimensions. The TS3704IN ordering information identifies the 14-pin PDIP configuration.
Does the TS3704IN output need an external pull-up resistor?
No external pull-up resistor is required because the TS3704IN uses push-pull CMOS outputs. According to the manufacturer datasheet, the push-pull output stage saves power and board space by eliminating the pull-up resistor normally used with conventional open-collector comparators. Designers must still observe the output voltage and current limits when driving a load or directly driving downstream digital circuitry.
What are the key specifications of TS3704IN that engineers should know?
The TS3704IN integrates four CMOS voltage comparators with a typical input offset voltage of 5 mV, typical input bias current of 600 pA, and response time of approximately 2 µs at 5 mV overdrive. It operates from a 3 V nominal supply, supports inputs up to ±8 V, and is available in a 14-pin PDIP package. These characteristics position it for low-power precision threshold and signal-processing circuits.
Is TS3704IN suitable for battery-powered sensor interfaces?
Yes, the TS3704IN is suitable for battery-powered sensor interfaces because each comparator typically consumes only 9 µA. Its CMOS input stage also provides high input impedance, helping reduce loading on high-resistance sensors. For low-energy designs, the four channels can monitor several sensor thresholds from one package, although the complete system budget must also include supply currents from other components.
TS3704IN vs TS3704ID - which package should I choose?
The TS3704IN is the identified 14-pin PDIP version, while TS3704ID is the same-family comparator ordered with the STMicroelectronics PDIP package designation. Both devices share the TS3704 quad CMOS architecture and are suitable for through-hole designs using the same 14-pin footprint. Confirm the exact suffix, temperature grade, and orderable packaging against the manufacturer ordering information before releasing a production BOM.
When should I choose TS3704IN over TS3704CDT?
Choose the TS3704IN when a through-hole PCB design requires the 14-pin PDIP footprint. The TS3704CDT is identified in comparison listings as the surface-mount family option, so it is not a drop-in substitute for a board designed specifically around through-hole holes. Both variants use the micropower quad CMOS comparator architecture, but their package footprints and assembly requirements differ.
What can replace TS3704IN on the same 14-pin footprint?
The closest same-family replacement identified for the TS3704IN footprint is the TS3704ID, which uses the STMicroelectronics PDIP package designation and retains the four-channel micropower CMOS architecture. Cross-reference listings specifically identify the TS3704 family as pin-to-pin and functionally compatible with the bipolar LM339, but an LM339 does not provide the same push-pull output behavior and therefore is not a strict drop-in replacement.
Is TS3704IN the same as an LM339?
The TS3704IN is pin-to-pin and functionally compatible with the LM339 according to the manufacturer datasheet, but its output implementation differs. The TS3704IN uses push-pull CMOS outputs and needs no external pull-up resistor, whereas the bipolar LM339 uses an open-collector output. Existing LM339 boards therefore require review of pull-up components and output-drive behavior before treating the devices as interchangeable.
What is the best STMicroelectronics equivalent for TS3704IN?
The best same-package STMicroelectronics alternative identified for the TS3704IN is the TS3704ID. It belongs to the same TS3704 micropower quad CMOS comparator family and uses the 14-pin PDIP package. The key engineering difference is principally the ordering suffix rather than a change in the four-channel push-pull architecture, so package marking and procurement requirements should be checked before substitution.
Where can I buy TS3704IN and check its current lead time?
Use the Request a Quote form on this page to ask about TS3704IN availability, current lead time, order quantity, and shipment arrangements. The manufacturer lists TS3704 as a product family, and the TS3704IN is identified by distributor listings as a 14-pin PDIP comparator. XAIPART will confirm the exact suffix, current lifecycle status, and deliverable configuration before an order is placed.
How should I design the PCB around TS3704IN?
Place supply bypassing close to the common supply pins and route each comparator's high-impedance input leads away from switching nodes and output traces. Keep the ground return short and provide a low-impedance reference for all four channels. If the sensed signals can carry high-frequency noise, add appropriately valued input filtering and verify that its added noise or response delay remains acceptable for the intended threshold.

Technische Referenzdaten für TS3704IN – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the TS3704IN when the design needs four low-power voltage-comparison functions and the PCB is built around a 14-pin PDIP footprint. Its typical 9 µA per comparator, high input impedance, and push-pull outputs are useful in battery-powered monitoring, industrial sensing, and low-power control systems. The TS3704ID is the closest same-package STMicroelectronics alternative when that ordering designation fits procurement and documentation requirements. Do not treat TS3704CDT or TS3704IPT as direct replacements because they use surface-mount packages. The LM339 is described as pin-to-pin and functionally compatible, but its open-collector output requires pull-up hardware and differs electrically from the TS3704. If the application emphasizes extremely low offset, very fast response, rail-to-rail operation, or automotive qualification, verify those requirements against the manufacturer datasheet before final selection.

Vergleich mit Alternativen

Parameter Dieses Produkt TS3704ID
Brand STMicroelectronics STMicroelectronics
Package 14-pin PDIP 14-pin PDIP
Number of Channels 4 channels 4 channels
Comparator Technology CMOS CMOS
Output Type Push-pull CMOS Push-pull CMOS
Typical Supply Current 9 µA per comparator 9 µA per comparator
Nominal Supply Voltage 3 V 3 V
Maximum Supply Voltage 16 V 16 V
Input Voltage Range ±8 V ±8 V
Typical Input Offset Voltage 5 mV 5 mV
Typical Response Time 2 µs at 5 mV overdrive 2 µs at 5 mV overdrive
Operating Temperature Range -40 °C to +125 °C -40 °C to +125 °C

Wichtigste Unterscheidungsmerkmale

  • Four complete comparison channels in one package (vs. TS3704ID)
  • Push-pull output architecture (vs. TS3704ID)
  • Low-power CMOS operation (vs. TS3704ID)

Designhinweise

Place the supply bypass capacitor close to the TS3704IN VCC pin and connect it to a low-impedance ground path. Because all four comparators share the same package, inadequate supply bypassing can couple disturbance from one switching channel into another. Route the high-impedance input nets away from output and switching-node traces, and use a continuous ground plane where practical.

The CMOS inputs provide high impedance, but they can still pick up noise when connected to long PCB traces or nearby switching circuitry. Add input-series resistance and capacitance only after checking their effect on response time. The manufacturer lists approximately 2 µs typical response at 5 mV overdrive; excessive filtering or a slow source impedance can lengthen the practical decision time.

Do not substitute an open-collector LM339 directly and assume identical output behavior. The manufacturer describes the TS3704 as pin-to-pin and functionally compatible with the LM339, but the TS3704 uses push-pull outputs while the LM339 requires an external pull-up resistor. Review the original PCB for pull-up networks, output load current, input polarity, and logic direction before approving a cross-family replacement.

Budget the comparator current as approximately 9 µA per channel, then include supply current from the complete TS3704IN device and any external logic. The nominal 3 V operating point does not guarantee that all inputs and outputs remain within their limits at every rail condition. Design protection around the maximum 16 V supply rating and ±8 V input range stated in the manufacturer datasheet.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The manufacturer datasheet describes the TS3704 family, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not established for the TS3704IN.

Ähnliche Suchanfragen

ts3704 datasheet TS3704IN datasheet TS3704IN datasheet pdf TS3704IN pinout TS3704IN specifications TS3704IN equivalent TS3704IN replacement TS3704IN cross reference TS3704IN vs TS3704ID TS3704IN PDIP footprint TS3704IN application circuit TS3704IN price TS3704IN stock STMicroelectronics TS3704IN TS3704IN four channel comparator

Verwandte Bauteile & Begriffe

STMicroelectronics TS3704IN TS3704 TS3704ID TS3704CDT TS3704IPT voltage comparator quad comparator analog comparator comparator IC CMOS push-pull output open-collector output LM339 PDIP-14 through-hole package micro-power low-dropout voltage input offset voltage input bias current input impedance response time battery monitoring industrial sensor interface threshold detection
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen