WM8595GEFL/RV - 24-Bit 192kHz Audio Codec | Cirrus Logic
MPN: WM8595GEFL/RV ✗ End of LifeWM8595GEFL/RV Overview
An audio codec is a mixed-signal interface IC that converts digital audio samples into analog signals, converts analog inputs into digital data, and provides the associated clocking, filtering, and signal-path controls. Within the broader semiconductor hierarchy, a codec belongs to the interface IC class, connects digital audio logic to analog circuitry, and sits between a processor or digital audio bus and external microphones, speakers, headphones, or line-level inputs.
The WM8595GEFL/RV's defining listed features include 24-bit audio resolution, operation to 192 kHz, and support for 2 Vrms signals. These figures indicate suitability for high-resolution playback, recording, and audio processing systems. The 192 kHz capability also makes the device relevant to professional monitoring and consumer applications that sample above the CD standard rate of 44.1 kHz, while the 2 Vrms output range can simplify matching to line-level downstream circuitry.
Integrating conversion functions into one codec can reduce the number of separate converters in an audio design. However, analog performance depends on the complete signal chain, including the digital audio interface, clock source, supply arrangement, decoupling, grounding, output filtering, and the impedances presented by the connected amplifier or recorder. The codec should therefore be evaluated as part of the board-level audio architecture rather than selected from resolution and sampling-rate specifications alone.
Typical uses include multichannel home entertainment equipment, active speaker systems, recording interfaces, digital mixers, audiovisual receivers, and communication terminals requiring synchronous analog and digital audio paths. The 48-QFN package supports compact designs, but its dense footprint makes careful escape routing and clean supply distribution important. Clocking, ground reference, analog routing, and exposed-pad thermal management should be planned before schematic capture.
The primary design consideration is signal integrity at the analog and digital interfaces. Keep analog input and output routing away from switching nodes, use the manufacturer-recommended decoupling and clock connections, and provide a continuous ground reference beneath the device. Verify timing margins and audio-channel mapping in the final schematic and layout because changes to clocking, grounding, or filtering can affect observable channel performance.
This page organizes the available WM8595GEFL/RV specifications, identifies the verified sourcing route for the manufacturer datasheet, compares the closely related WM8595GEFL/V device, and summarizes practical packaging, replacement, lifecycle, and sourcing considerations. It also highlights where detailed electrical, acoustic, pinout, and application information must be confirmed in the official device documentation before a production design is released.
Drop-in alternatives for WM8595GEFL/RV — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with WM8595GEFL/RV (same form factor and footprint) — differing in Product Type.
WM8595GEFL/V
✅ Drop-InContact for price
View Datasheet →WM8595GEFL/RV Maximum Ratings & Electrical Characteristics
| Product Type | Multichannel audio codec |
| Audio Resolution | 24 bit |
| Maximum Sampling Rate | 192 kHz |
| Output Signal Level | 2 Vrms |
| Package | 48-pin QFN |
| Mounting Type | Surface mount |
| Device Category | Interface IC / Audio codec |
| Manufacturer | Cirrus Logic |
| Legacy Brand | Wolfson |
WM8595GEFL/RV 48-pin qfn Pin Configuration Guide
Pin configuration for WM8595GEFL/RV (48-pin qfn package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for WM8595GEFL/RV.
Refer to the datasheet for full pin configuration.
Typical Applications
WM8595GEFL/RV is suitable for 6 applications: High-Resolution Home Audio, Active Speaker System, Digital Recording Interface, Multichannel AV Receiver, Digital Mixer and Console, Communication and Multimedia Terminal.
High-Resolution Home Audio
The WM8595GEFL/RV fits high-resolution home-audio designs that operate at 24-bit resolution and require sampling rates up to 192 kHz. Its 2 Vrms output capability can support line-level signal routing into a conventional amplifier input, subject to the coupling, loading, filtering, and grounding details in the manufacturer application guidance. In a receiver or active-speaker design, the codec can serve as the central analog-to-digital and digital-to-analog interface. The practical benefit is a single conversion component for high-rate playback rather than separate converters for each direction. Designers should still preserve clean analog routing, use a low-jitter master clock, verify output amplitude against downstream gain stages, and confirm the complete pin and electrical requirements in the manufacturer datasheet before finalizing the board.
Recommended
Active Speaker System
In an active speaker or compact multimedia enclosure, the WM8595GEFL/RV can provide the shared conversion interface between a digital audio source and line-level amplification circuitry. Its 24-bit resolution supports high-resolution source formats, while operation up to 192 kHz provides headroom for high-rate processing. The 2 Vrms output is relevant when matching the codec output to the input sensitivity of a power-amplifier stage. Because enclosure acoustics and amplifier behavior can expose small grounding or impedance problems, keep the analog path short and evaluate channel balance in the assembled system. The clock source, supply decoupling, analog reference, and output filtering should follow the manufacturer guidance to preserve signal integrity.
Recommended
Digital Recording Interface
The WM8595GEFL/RV can serve in a digital recording interface where a processor requires both analog capture and high-rate playback through one codec. Its listed 24-bit resolution supports detailed digital audio data, and the 192 kHz capability permits high-rate conversion workflows when the host interface, storage path, and software chain can operate at the same rate. The 2 Vrms specification describes the codec’s listed output signal level; input limits, common-mode range, and conversion performance must be taken from the manufacturer datasheet. Board-level implementation should emphasize low-noise clocking, isolated analog and digital return paths, correct input filtering, and short routing from external connectors to the codec.
Recommended
Multichannel AV Receiver
A multichannel audiovisual receiver can use the WM8595GEFL/RV to handle high-rate audio conversion around a digital audio processor. The device’s 24-bit format and 192 kHz maximum rate are compatible with demanding contemporary media paths, while its 2 Vrms output can feed line-level routing stages when levels are configured correctly. In such a system, channel mapping, clock synchronization, mute behavior, and channel delay must be validated together. Placement within the PCB should separate sensitive analog routes from processor and power-converter switching areas. Use a continuous ground strategy and the manufacturer-recommended component values around the codec, since substitutions in filters or reference networks may influence noise and channel balance.
Recommended
Digital Mixer and Console
The WM8595GEFL/RV is applicable to digital mixers and production consoles that require centralized high-resolution analog input and output conversion. Its 192 kHz maximum operating rate can support high-rate monitoring and processing workflows, while 24-bit resolution maintains a suitable numerical format for modern mixing software. The 2 Vrms output level can be useful for balanced or unbalanced line-routing stages when the analog front end is designed around the codec’s specified output swing. Practical implementation requires careful channel mapping, low-noise clock distribution, stable reference design, and isolated routing between microphone or line inputs and processor-associated circuitry. Validate grounding and gain structure in hardware to avoid channel-dependent noise or offset.
Recommended
Communication and Multimedia Terminal
The WM8595GEFL/RV can support audio functions in multimedia terminals and communication equipment that combine microphone or line capture with digital playback. The integrated codec architecture reduces the number of separate conversion ICs, while 24-bit operation and sampling up to 192 kHz provide flexibility for voice processing, conferencing, media playback, or local monitoring. The 2 Vrms output can feed an audio amplifier or line driver when the system gain and coupling arrangement are compatible. Designers should account for echo-control processing latency, codec clocking, channel alignment, and electromagnetic separation between analog inputs and high-speed digital circuits. Firmware configuration and the complete register-based control sequence must be implemented using the manufacturer documentation.
Recommended
Recommended Products Summary
Engineering reference data for WM8595GEFL/RV — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | WM8595GEFL/V |
|---|---|---|
| Brand | Cirrus Logic | Cirrus Logic |
| Package | 48-pin QFN | 48-pin QFN - same package family |
| Product Type | Multichannel audio codec | Multichannel audio codec |
Key Differentiators
- Supports high-rate, high-resolution conversion (vs WM8595GEFL/V)
- Provides a stated 2 Vrms output level (vs WM8595GEFL/V)
- Combines multichannel conversion in a compact package (vs WM8595GEFL/V)
Design Notes
Keep analog input and output traces short, quiet, and away from switching-regulator, clock, and high-speed digital routes. Maintain a continuous ground reference under the codec and use the manufacturer’s recommended ground and decoupling topology. A 48-QFN footprint also requires inspection of the exposed-pad connection, solder-paste pattern, via arrangement, and thermal-via pattern before releasing artwork.
Treat the audio master clock as a high-quality signal even when its frequency is not the highest data rate. Route it away from analog inputs, use short clock connections, follow the manufacturer’s source and load recommendations, and verify jitter and timing margins in the assembled board. Incorrect clock routing can create errors or audible artifacts that cannot be diagnosed from converter resolution alone.
Do not assume that a shared package makes every WM8595 suffix automatically interchangeable. Confirm the ordering table, electrical limits, temperature grade, pin mapping, clock configuration, and qualification status for WM8595GEFL/RV versus WM8595GEFL/V. Also avoid changing recommended filter, reference, or decoupling values without reviewing the manufacturer’s signal-path and application guidance.
Compliance Information
Compliance attributes were not stated in the available product listings and require confirmation from the manufacturer documentation.