Zilog

Z86E2112PSC - 8-Bit 12MHz OTP Microcontroller | Zilog

MPN: Z86E2112PSC ✓ Active
5 V Vdss 40-pin PDIP Package 12 MHz Speed One-time programmable (OTP) Memory
MOQ: 1 |

Z86E2112PSC Overview

The Zilog Z86E2112PSC is an 8-bit CISC microcontroller operating at up to 12 MHz, with 8 KB of one-time-programmable memory and UART communication capability in a 40-pin PDIP package. Its 5 V supply operation and compact embedded-control architecture suit applications that require deterministic serial control, keypad or switch input handling, and general-purpose logic without an external memory interface.

An 8-bit microcontroller is a compact processing component designed for embedded control. It belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductors. Compared with a field-programmable controller, one-time-programmable memory is written during manufacturing or provisioning and cannot be rewritten afterward. This makes the Z86E2112PSC appropriate for products whose firmware is fixed and whose production configuration benefits from reduced update complexity.

The principal device characteristics are an 8-bit CPU, a 12 MHz maximum clock, 8 KB of OTP program memory, 5 V operation, and a 40-pin PDIP package. The listed memory organization is 8K x 8 bits, matching one byte for each of the 8,192 program-memory locations. UART capability provides a practical interface for host controllers, debug equipment, programmable controllers, and service equipment.

The CISC architecture favors compact, straightforward instruction handling and is well matched to cost-sensitive embedded products. Because the program memory is one-time programmable, firmware changes require a new programmed device rather than a field update. The 12 MHz operating ceiling also gives designers a clear timing basis when selecting oscillator components, communication baud rates, and interrupt-service routines.

Typical uses include serial control panels, industrial operator interfaces, building-control terminals, appliance controllers, programmable logic controllers, and compact test fixtures. In each case, the MCU can coordinate inputs and outputs while the UART provides a defined path for commands or status information. The 40-pin PDIP package also simplifies prototype construction and through-hole inspection where a socket is acceptable.

Before finalizing a PCB design, assign every physical pin by consulting the manufacturer's pin-description table and confirm the oscillator, reset, and I/O requirements for the selected firmware configuration. Because OTP memory cannot be corrected after programming, complete the code and programming procedure before committing devices to production.

This page consolidates the device identity, package information, memory capacity, clock rate, UART feature, sourcing workflow, and engineering considerations into a compact reference for designers evaluating the Z86E2112PSC.

Drop-in alternatives for Z86E2112PSC — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with Z86E2112PSC (same form factor and footprint) — differing in Maximum Clock Frequency, Program Memory Organization, Program Memory Type.

Zilog
Maximum Clock Frequency: 16 MHz
Program Memory Organization: 8K x 8
Program Memory Type: One-time programmable
Compare with Z86E2112PSC →

No drop-in alternatives available for this product.

Request Alternatives

Z86E2112PSC Maximum Ratings & Electrical Characteristics

Microcontroller Type 8-bit CISC microcontroller
Processor Architecture CISC
Maximum Clock Frequency 12 MHz
Program Memory Type One-time programmable (OTP)
Program Memory Capacity 8 KB
Program Memory Organization 8K x 8 bits
Supply Voltage 5 V
Serial Interface UART
Package Type 40-pin PDIP
Pin Count 40 pins
Mounting Type Through-hole
Product Series Z8 series

Z86E2112PSC 40-pin pdip Pin Configuration Guide

Pin configuration for Z86E2112PSC (40-pin pdip package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.

40-pin pdip package pinout diagram for Z86E2112PSC

No detailed pinout data available for Z86E2112PSC.

Refer to the datasheet for full pin configuration.

Typical Applications

Z86E2112PSC is suitable for 6 applications: Serial Appliance Controller, Industrial Operator Panel, Programmable Logic Controller, Building-Control Terminal, Test and Measurement Fixture, Remote Sensor Interface.

🔧

Serial Appliance Controller

The Z86E2112PSC can serve as the central controller in a cost-sensitive appliance or countertop product that requires a stable 5 V supply, an 8-bit control CPU, and UART communication. Its 12 MHz operating rate provides a defined basis for switch scanning, timing, and communication handling, while 8 KB of OTP memory is sufficient for a fixed control program and compact state machine. Place the controller between the operator inputs and a UART-connected front panel, display, or service interface. Because program memory is one-time programmable, the complete firmware and production programming sequence should be validated before device commitment. The 40-pin PDIP package also makes prototype wiring and inspection straightforward, although it occupies more PCB area than a surface-mount equivalent.

🏭

Industrial Operator Panel

The Z86E2112PSC is appropriate for a compact operator panel that receives commands over a UART and translates them into lamp, relay, switch, or display-control actions. Its 8-bit CISC architecture supports straightforward embedded logic, while the 12 MHz clock gives designers a concrete timing reference for debouncing, event scheduling, and serial response routines. A practical implementation uses the MCU for panel-state management and a separate driver stage for loads that exceed logic-level output capability. Before deployment, verify the operating-temperature range and electrical limits against the manufacturer datasheet, since industrial environmental requirements may exceed the base device specification.

🏭

Programmable Logic Controller

The Z86E2112PSC can implement a small PLC-like control node when the required program fits within 8 KB of OTP memory. At 12 MHz, the controller can coordinate discrete inputs, outputs, counters, interlocks, and UART-connected supervisory equipment. Keep the control program deterministic by grouping time-critical logic into interrupt handlers and avoiding unnecessary dynamic-memory assumptions. Because the device cannot be reprogrammed after programming, field maintenance must rely on replaceable hardware or an external nonvolatile controller. The through-hole PDIP package is particularly useful during equipment retrofits where a socketed prototype can simplify substitution and inspection.

🧩

Building-Control Terminal

The Z86E2112PSC is suitable for a fixed building-control terminal that gathers switch or sensor states and reports them through a UART-connected controller. Its 8 KB OTP memory allows a compact, deterministic firmware image, and the 5 V operating point fits many low-voltage control boards. Place transient protection and grounding appropriate to the installation environment around the interface, then confirm that the selected MCU pins support the intended input and output functions. The one-time-programmable architecture is useful for high-volume products where field firmware updates are unnecessary, but a new programmed MCU is required whenever logic changes are approved.

🔧

Test and Measurement Fixture

The Z86E2112PSC can control a compact test fixture in which a host computer issues commands over UART and the MCU drives relays, indicators, or measurement-control signals. The 12 MHz clock and 8-bit architecture provide sufficient processing capability for fixed sequencing logic, handshake handling, and fault reporting. Use the 40-pin PDIP package for a socketed prototype during fixture development, then assess a smaller production package only after confirming pin-level compatibility and environmental requirements. Validate every output path against the maximum voltage and current ratings in the manufacturer datasheet rather than assuming all I/O pins have identical drive capabilities.

📡

Remote Sensor Interface

The Z86E2112PSC can act as a remote sensor-conditioning and communication node when the sensor interface requires digital control rather than analog signal processing. Its 8 KB OTP memory holds acquisition sequencing, calibration constants, filtering, and status logic, while UART carries readings to a local controller. The 12 MHz operating rate supports responsive polling and interrupt-driven updates. Care is required at the sensor interface because the MCU's 5 V digital supply and individual I/O limits do not automatically support arbitrary sensor voltage levels. Add suitable signal conditioning, protection, and level translation, and consult the manufacturer's electrical-characteristics table before finalizing the schematic.

What is the Z86E2112PSC?
The Z86E2112PSC is a Zilog Z8-series 8-bit CISC microcontroller rated for operation at up to 12 MHz and 5 V. It contains 8 KB of one-time-programmable memory organized as 8K x 8 bits, includes UART communication capability, and is supplied in a 40-pin PDIP package. According to the manufacturer datasheet, these characteristics position it for compact embedded-control and serial-communication designs.
What are the key specifications of Z86E2112PSC that engineers should know?
The key Z86E2112PSC specifications are an 8-bit CISC processor, 12 MHz maximum operating frequency, 8 KB of OTP program memory, 5 V operation, UART support, and a 40-pin PDIP package. According to the manufacturer datasheet, the program memory is organized as 8K x 8 bits. The OTP configuration is permanent after programming, so firmware validation must occur before production programming.
How much program memory does Z86E2112PSC have?
The Z86E2112PSC has 8 KB of one-time-programmable program memory organized as 8K x 8 bits, meaning 8,192 eight-bit locations. According to the manufacturer datasheet, this memory cannot be rewritten after the device is programmed. Production planning should therefore include complete firmware validation and a controlled programming workflow before components are populated or programmed.
What is the maximum operating frequency of Z86E2112PSC?
The maximum operating frequency of the Z86E2112PSC is 12 MHz. According to the manufacturer datasheet, the device is an 8-bit CISC microcontroller intended for 5 V operation. Use that frequency as the timing reference for oscillator selection, serial baud-rate generation, interrupt servicing, and execution-time analysis in embedded firmware.
Where can I download the Z86E2112PSC datasheet PDF?
The Z86E2112PSC datasheet archive is available at https://www.datasheetarchive.com/?q=z86e2112psc. Use the manufacturer datasheet for the authoritative pin-description table, electrical characteristics, memory map, and programming instructions. The archive may also expose documents from third-party indexes, so confirm the manufacturer name, device suffix, and package information before using a document for design work.
Where can I find the Z86E2112PSC pinout?
Use the pin-description table in the Zilog manufacturer datasheet to assign the Z86E2112PSC's 40 PDIP pins. The device is identified as a 40-pin PDIP package, but individual signal names are not shown in the product summaries. Begin with the datasheet's package drawing and pin table, then cross-check pin 1 orientation against the physical notch or marking on the PCB footprint.
Where can I buy Z86E2112PSC online?
Use the Request a Quote form on this page to request Z86E2112PSC availability, packaging details, and a current quotation. The part is identified by Zilog as an 8-bit, 12 MHz microcontroller with 8 KB OTP memory and UART capability. A written quotation allows the requested package, quantity, delivery location, and production schedule to be confirmed together.
What is the price of Z86E2112PSC?
Use the Request a Quote form on this page for the current Z86E2112PSC quotation. The component is listed as a 40-pin PDIP Z8-series microcontroller with 8 KB of OTP memory and a 12 MHz clock. Quote requests should specify the required quantity, reel or tube packaging if applicable, delivery destination, and target production schedule so the commercial response reflects the actual build.
What is the lead time for Z86E2112PSC?
Request the current Z86E2112PSC lead time through the Request a Quote form on this page. Include your required quantity, approved packaging, shipment destination, production date, and whether procurement must hold a single lot for planning purposes. A firm delivery commitment should be obtained before the OTP programming schedule is finalized.
Is Z86E2112PSC in stock?
Check current Z86E2112PSC availability by submitting a stock and delivery request through the Request a Quote form on this page. Include the required quantity, package preference, destination, and required date. This approach accounts for changing inventory, lot allocation, and logistics rather than treating a distributor landing page as a guarantee that the exact suffix is immediately available.
What can replace Z86E2112PSC?
A valid drop-in replacement for the Z86E2112PSC must match the 40-pin PDIP footprint, preserve pin-to-pin signal assignments, and remain within the device's key operating limits of 12 MHz, 5 V, 8 KB OTP memory, and UART capability. No confirmed 40-pin drop-in replacement is identified on this product page. Use the Request a Quote form for sourcing support when an exact, validated substitute is required.
Is Z86E2112PSC suitable for an industrial control panel?
The Z86E2112PSC is suitable for a compact serial control panel when the design accepts one-time-programmable firmware, requires UART communication, and can use a 40-pin through-hole package. Its 12 MHz clock and 8 KB OTP memory support embedded command handling and status logic. Industrial suitability still depends on temperature range, electrical limits, environmental qualification, and isolation requirements from the manufacturer datasheet.
When should I choose Z86E2112PSC over a microcontroller with flash memory?
Choose the Z86E2112PSC when firmware will remain permanently fixed and the design benefits from an 8-bit controller with 8 KB OTP memory, a 12 MHz clock, UART support, and a 40-pin PDIP package. Select a flash-memory controller instead when field updates, post-deployment bug correction, bootloader upgrades, or larger firmware images are required, because OTP memory cannot be rewritten after programming.
Z86E2112PSC vs Z86E4016PSG - which is better for a control system?
The Z86E2112PSC is the documented choice for an 8-bit, 12 MHz, 8 KB OTP design using a 40-pin PDIP package and UART. A Z86E4016PSG comparison requires checking its package, pinout, voltage, memory, and timing against the completed PCB. The two devices must not be treated as interchangeable unless their manufacturer datasheets establish matching 40-pin footprints and functional pin assignments.
What is the difference between Z86E2112PSC and Z86E6316PSG?
The Z86E2112PSC is identified as a 40-pin PDIP Z8-series device with an 8-bit CPU, 12 MHz clock, 8 KB OTP memory, and UART. The Z86E6316PSG may differ in package, memory, voltage, or peripheral configuration, so it is not a drop-in substitute without a direct datasheet comparison. Review pin assignments, supply limits, program-memory type, and timing before choosing a cross-family replacement.

Engineering reference data for Z86E2112PSC — comparison, design guidance, and compliance information.

Selection Guide

Choose the Z86E2112PSC when the product needs an 8-bit Z8-family controller running at up to 12 MHz from a 5 V supply, with 8 KB of permanent OTP program memory, UART communication, and a 40-pin PDIP footprint. It is especially practical for high-volume appliances, compact control panels, fixtures, and building-control nodes where firmware will not change after manufacturing. Select a flash-memory MCU instead when field updates, bootloader upgrades, or large application images are essential. Before considering another Zilog or cross-brand device, require an exact comparison of package dimensions, pin assignments, supply range, clock requirements, memory organization, peripheral functions, and programming process. The absence of a confirmed drop-in replacement means that changing the MCU may require a PCB redesign rather than a simple component substitution.

Comparison with Alternatives

Parameter This Product
Package 40-pin PDIP
Brand Zilog
Processor Architecture 8-bit CISC
Maximum Clock Frequency 12 MHz
Program Memory 8 KB OTP
Program Memory Organization 8K x 8 bits
Supply Voltage 5 V
Serial Interface UART
Product Series Z8 series

Key Differentiators

  • Permanent firmware storage in an 8-bit embedded controller (vs Z86E4016PSG)
  • Defined 12 MHz processing and serial-control basis (vs Z86E6316PSG)
  • Prototype-friendly 40-pin through-hole package (vs Z86E2112PSC)

Design Notes

Treat the OTP program memory as a one-way manufacturing step. A checksum or functional error cannot be repaired by reflashing the MCU. Before production programming, validate the complete firmware image, interrupt vectors, startup sequence, UART configuration, and application I/O behavior on representative hardware. Preserve a controlled copy of the exact programmed image and its version identifier for traceability.

Assign the physical 40 pins from the manufacturer's pin-description table and package drawing before releasing the PCB footprint. Confirm the pin-1 orientation using the PDIP notch or pin-1 marker, then verify every power, ground, oscillator, reset, and I/O connection. If the design uses a socket for prototypes, include adequate clearance for mechanical inspection and avoid placing tall nearby components where they can interfere with the socket.

The device is identified as a 5 V part, so the supply rail must remain within the manufacturer-defined operating limits. Decouple the supply close to the device using the capacitance and placement required by the datasheet, and keep return-current paths short. Do not infer the allowable input voltage, output-drive limits, or oscillator amplitude from nominal device descriptions; verify each electrical limit before designing surrounding circuitry.

Route UART signals away from switching nodes and high-current return paths, and provide the correct interface levels for the connected equipment. If a longer cable or industrial environment is involved, use a suitable differential or isolated communications architecture rather than relying on the MCU's UART pins for long-distance signaling. Confirm signal polarity, logic levels, baud-rate tolerance, grounding, and connector requirements in the system interface specification.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

Compliance declarations are not stated in the available product records. Confirm the exact device suffix and its current compliance documentation with Zilog before procurement.

Data verified on: 2026-11-11 — data verified and curated by XAIPART's component engineering team

Related Searches

Z86E2112PSC datasheet Z86E2112PSC pinout Z86E2112PSC datasheet PDF Z86E2112PSC equivalent Z86E2112PSC replacement Z86E2112PSC cross reference Z86E2112PSC 40 pin PDIP Z86E2112PSC 12 MHz Z86E2112PSC 8KB OTP Z86E2112PSC price Z86E2112PSC stock Zilog Z86E2112PSC

Related Components & Terms

Zilog Z86E2112PSC Z8 series 8-bit microcontroller CISC architecture embedded microcontroller embedded processor semiconductor one-time-programmable memory OTP 8K x 8 bits 12 MHz clock 5 V supply UART 40-pin PDIP through-hole package surface-mount package programmable logic controller industrial control panel appliance controller building-control terminal test fixture remote sensor interface MC1489NE4
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details