Z86E2112PSC - 8-Bit 12MHz OTP Microcontroller | Zilog
MPN: Z86E2112PSC ✓ NakahandaZ86E2112PSC Ulas
An 8-bit microcontroller is a compact processing component designed for embedded control. It belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductors. Compared with a field-programmable controller, one-time-programmable memory is written during manufacturing or provisioning and cannot be rewritten afterward. This makes the Z86E2112PSC appropriate for products whose firmware is fixed and whose production configuration benefits from reduced update complexity.
The principal device characteristics are an 8-bit CPU, a 12 MHz maximum clock, 8 KB of OTP program memory, 5 V operation, and a 40-pin PDIP package. The listed memory organization is 8K x 8 bits, matching one byte for each of the 8,192 program-memory locations. UART capability provides a practical interface for host controllers, debug equipment, programmable controllers, and service equipment.
The CISC architecture favors compact, straightforward instruction handling and is well matched to cost-sensitive embedded products. Because the program memory is one-time programmable, firmware changes require a new programmed device rather than a field update. The 12 MHz operating ceiling also gives designers a clear timing basis when selecting oscillator components, communication baud rates, and interrupt-service routines.
Typical uses include serial control panels, industrial operator interfaces, building-control terminals, appliance controllers, programmable logic controllers, and compact test fixtures. In each case, the MCU can coordinate inputs and outputs while the UART provides a defined path for commands or status information. The 40-pin PDIP package also simplifies prototype construction and through-hole inspection where a socket is acceptable.
Before finalizing a PCB design, assign every physical pin by consulting the manufacturer's pin-description table and confirm the oscillator, reset, and I/O requirements for the selected firmware configuration. Because OTP memory cannot be corrected after programming, complete the code and programming procedure before committing devices to production.
This page consolidates the device identity, package information, memory capacity, clock rate, UART feature, sourcing workflow, and engineering considerations into a compact reference for designers evaluating the Z86E2112PSC.
Mga alternatibo na pwedeng ilagay na Z86E2112PSC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok Z86E2112PSC (parehas na form factor at footprint) — pagkakaiba sa Maximum Clock Frequency, Program Memory Organization, Program Memory Type.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboZ86E2112PSC Mga Pinakamataas na Rating at Electrical Characteristics
| Microcontroller Type | 8-bit CISC microcontroller |
| Processor Architecture | CISC |
| Maksimum na Taktiko ng Oras | 12 MHz |
| Program Memory Type | One-time programmable (OTP) |
| Program Memory Capacity | 8 KB |
| Program Memory Organization | 8K x 8 bits |
| Volte ng Pagbibigay | 5 V |
| Serial Interface | UART |
| Package Type | 40-pin PDIP |
| Bilang ng Pin | 40 pins |
| Uri ng Pagpapasok | Through-hole |
| Product Series | Z8 series |
Gabay sa Pin Configuration ng Z86E2112PSC 40-pin pdip
Pin configuration para sa Z86E2112PSC (40-pin pdip package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa Z86E2112PSC.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
Z86E2112PSC ay nararapat para sa 6 aplikasyons: Serial Appliance Controller, Industrial Operator Panel, Programmable Logic Controller, Building-Control Terminal, Test and Measurement Fixture, Remote Sensor Interface.
Serial Appliance Controller
The Z86E2112PSC can serve as the central controller in a cost-sensitive appliance or countertop product that requires a stable 5 V supply, an 8-bit control CPU, and UART communication. Its 12 MHz operating rate provides a defined basis for switch scanning, timing, and communication handling, while 8 KB of OTP memory is sufficient for a fixed control program and compact state machine. Place the controller between the operator inputs and a UART-connected front panel, display, or service interface. Because program memory is one-time programmable, the complete firmware and production programming sequence should be validated before device commitment. The 40-pin PDIP package also makes prototype wiring and inspection straightforward, although it occupies more PCB area than a surface-mount equivalent.
Inirekomenda
Industrial Operator Panel
The Z86E2112PSC is appropriate for a compact operator panel that receives commands over a UART and translates them into lamp, relay, switch, or display-control actions. Its 8-bit CISC architecture supports straightforward embedded logic, while the 12 MHz clock gives designers a concrete timing reference for debouncing, event scheduling, and serial response routines. A practical implementation uses the MCU for panel-state management and a separate driver stage for loads that exceed logic-level output capability. Before deployment, verify the operating-temperature range and electrical limits against the manufacturer datasheet, since industrial environmental requirements may exceed the base device specification.
Inirekomenda
Programmable Logic Controller
The Z86E2112PSC can implement a small PLC-like control node when the required program fits within 8 KB of OTP memory. At 12 MHz, the controller can coordinate discrete inputs, outputs, counters, interlocks, and UART-connected supervisory equipment. Keep the control program deterministic by grouping time-critical logic into interrupt handlers and avoiding unnecessary dynamic-memory assumptions. Because the device cannot be reprogrammed after programming, field maintenance must rely on replaceable hardware or an external nonvolatile controller. The through-hole PDIP package is particularly useful during equipment retrofits where a socketed prototype can simplify substitution and inspection.
Inirekomenda
Building-Control Terminal
The Z86E2112PSC is suitable for a fixed building-control terminal that gathers switch or sensor states and reports them through a UART-connected controller. Its 8 KB OTP memory allows a compact, deterministic firmware image, and the 5 V operating point fits many low-voltage control boards. Place transient protection and grounding appropriate to the installation environment around the interface, then confirm that the selected MCU pins support the intended input and output functions. The one-time-programmable architecture is useful for high-volume products where field firmware updates are unnecessary, but a new programmed MCU is required whenever logic changes are approved.
Inirekomenda
Test and Measurement Fixture
The Z86E2112PSC can control a compact test fixture in which a host computer issues commands over UART and the MCU drives relays, indicators, or measurement-control signals. The 12 MHz clock and 8-bit architecture provide sufficient processing capability for fixed sequencing logic, handshake handling, and fault reporting. Use the 40-pin PDIP package for a socketed prototype during fixture development, then assess a smaller production package only after confirming pin-level compatibility and environmental requirements. Validate every output path against the maximum voltage and current ratings in the manufacturer datasheet rather than assuming all I/O pins have identical drive capabilities.
Inirekomenda
Remote Sensor Interface
The Z86E2112PSC can act as a remote sensor-conditioning and communication node when the sensor interface requires digital control rather than analog signal processing. Its 8 KB OTP memory holds acquisition sequencing, calibration constants, filtering, and status logic, while UART carries readings to a local controller. The 12 MHz operating rate supports responsive polling and interrupt-driven updates. Care is required at the sensor interface because the MCU's 5 V digital supply and individual I/O limits do not automatically support arbitrary sensor voltage levels. Add suitable signal conditioning, protection, and level translation, and consult the manufacturer's electrical-characteristics table before finalizing the schematic.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for Z86E2112PSC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Package | 40-pin PDIP |
| Brand | Zilog |
| Processor Architecture | 8-bit CISC |
| Maximum Clock Frequency | 12 MHz |
| Program Memory | 8 KB OTP |
| Program Memory Organization | 8K x 8 bits |
| Supply Voltage | 5 V |
| Serial Interface | UART |
| Product Series | Z8 series |
Pangunahing mga Pagkakaiba
- Permanent firmware storage in an 8-bit embedded controller (kumpara saZ86E4016PSG)
- Defined 12 MHz processing and serial-control basis (kumpara saZ86E6316PSG)
- Prototype-friendly 40-pin through-hole package (kumpara saZ86E2112PSC)
Talaan ng Disenyo
Treat the OTP program memory as a one-way manufacturing step. A checksum or functional error cannot be repaired by reflashing the MCU. Before production programming, validate the complete firmware image, interrupt vectors, startup sequence, UART configuration, and application I/O behavior on representative hardware. Preserve a controlled copy of the exact programmed image and its version identifier for traceability.
Assign the physical 40 pins from the manufacturer's pin-description table and package drawing before releasing the PCB footprint. Confirm the pin-1 orientation using the PDIP notch or pin-1 marker, then verify every power, ground, oscillator, reset, and I/O connection. If the design uses a socket for prototypes, include adequate clearance for mechanical inspection and avoid placing tall nearby components where they can interfere with the socket.
The device is identified as a 5 V part, so the supply rail must remain within the manufacturer-defined operating limits. Decouple the supply close to the device using the capacitance and placement required by the datasheet, and keep return-current paths short. Do not infer the allowable input voltage, output-drive limits, or oscillator amplitude from nominal device descriptions; verify each electrical limit before designing surrounding circuitry.
Route UART signals away from switching nodes and high-current return paths, and provide the correct interface levels for the connected equipment. If a longer cable or industrial environment is involved, use a suitable differential or isolated communications architecture rather than relying on the MCU's UART pins for long-distance signaling. Confirm signal polarity, logic levels, baud-rate tolerance, grounding, and connector requirements in the system interface specification.
Impormasyon ng Pagsunod sa Kautusan
Compliance declarations are not stated in the available product records. Confirm the exact device suffix and its current compliance documentation with Zilog before procurement.