Circuitos Integrados

THS4304D

THS4304D - 3 GHz Low-Noise Wideband Op Amp | Texas Instruments

The Texas Instruments THS4304D is a single wideband, voltage-feedback operational amplifier optimized for high-speed analog signal-processing chains. It operates from a single 5 V supply, provides 3 GHz small-signal bandwidth, and is available in an 8-pin SOIC package. The THS4304 uses BiCom3 silicon-germanium process technology to combine wide bandwidth with low noise for applications that previously required dual-supply amplifiers. A wideband operational amplifier is a voltage-feedback amplifier designed to amplify signals over a much broader frequency range than conventional precision op amps. Its place in the signal-chain hierarchy is between general-purpose amplifiers and specialized high-speed RF components: it provides gain, buffering, filtering, and impedance conversion while operating from a single supply. The THS4304 is therefore suited to analog front ends where signal bandwidth, supply simplicity, and low-noise performance are more important than rail-to-rail input or output operation. The verified manufacturer description identifies the THS4304 as a 3 GHz low-noise wideband operational amplifier. Its voltage-feedback architecture is appropriate for closed-loop gains defined by external resistors, while the single 5 V supply simplifies system power compared with traditional plus-and-minus 5 V analog designs. The device is manufactured in the BiCom3 silicon-germanium process, a process technology specifically cited by Texas Instruments for this amplifier family. Typical uses include high-speed instrumentation, communication receivers, analog filters, data-acquisition front ends, and signal-conditioning chains. The amplifier can be used where a compact single-supply solution must process high-frequency signals without adopting a more complex multi-rail power architecture. Its wide bandwidth makes feedback and stability layout particularly important; resistor values, parasitic capacitance, grounding, and supply decoupling must be controlled close to the device pins. The 8-pin SOIC package is a surface-mount package in the SOIC family. Designers should consult the manufacturer datasheet for the complete pinout, electrical characteristics, recommended application circuits, stability requirements, and absolute maximum ratings. Because the available verified results do not expose every numeric electrical specification, values not explicitly present in the supplied data are marked as [DATA_NEEDED] rather than inferred. This page consolidates the verified Texas Instruments product identity, manufacturer datasheet link, distributor product records, package information, and cross-reference search results. It also distinguishes the THS4304D orderable 8-pin SOIC variant from related device names and avoids presenting unverified substitute parts as drop-in replacements. For purchasing, use the linked manufacturer and distributor records to confirm current price, stock, lead time, lifecycle status, and supported orderable variants.

Cotação Contato

THS4522IPWR

THS4522 - 95MHz Low Power Dual FDA | Texas Instruments

The Texas Instruments THS4522 is a very low-power, dual-channel, fully differential amplifier (FDA) with rail-to-rail output and an input common-mode range that includes the negative rail. It operates from a single 2.5V to 5.5V supply and delivers 95 MHz bandwidth at a gain of 1, 100 V/us slew rate, and only 1.1 mA quiescent current per channel in a 16-pin TSSOP (PW) package specified from -40C to +125C. A fully differential amplifier (FDA) is an operational amplifier with differential inputs and differential outputs, providing balanced positive and negative signal phases simultaneously. FDAs are essential for driving high-performance ADCs because balanced signaling improves common-mode rejection and suppresses even-order harmonics. As a subset of operational amplifiers within analog signal processing, FDAs enable precise amplification, filtering, and level shifting in data converter front-end circuits. Key features include very low input voltage noise of 4.6 nV/rtHz, low distortion of -110 dBc at 1 MHz, and 55 mA output current. A power-down pin reduces quiescent current to 0.5 uA, and the rail-to-rail output maximizes dynamic range in single-supply systems. Negative rail input capability simplifies interfacing with ground-referenced sensors. The THS4522 uses a complementary bipolar process with a precision input stage, achieving 0.5 mV offset voltage and a 95 MHz gain bandwidth product. Full specification across the industrial temperature range ensures reliable operation in harsh environments, while the dual-channel TSSOP-16 configuration saves board space in multi-channel systems. Typical applications include driving high-speed ADCs in medical imaging, industrial process control, and test and measurement equipment. Low power consumption makes it suitable for portable battery-powered instruments, and rail-to-rail output with negative-rail input enables single-supply sensor interfaces. When designing with the THS4522, decouple supplies with 0.1 uF and 10 uF capacitors close to the VCC and VEE pins, use precision low-TCR feedback resistors to maintain gain accuracy, and bypass the VOCM pin to ground for optimal output common-mode control.

Cotação Contato

THS4531A

THS4531A - Ultra-Low-Power Fully Differential Amplifier | TI

The THS4531A from Texas Instruments is an ultra-low-power, fully differential amplifier with rail-to-rail output and an input common-mode range that extends below the negative rail. It is designed for low-power data acquisition systems and high-density applications where power consumption and dissipation are critical. The device operates from a single supply of 2.5V to 5.5V or dual supplies of ±1.25V to ±2.75V, and it consumes only 250µA of quiescent current, making it one of the most power-efficient fully differential amplifiers available. A fully differential amplifier (FDA) is an operational amplifier with differential inputs and differential outputs, providing both the signal and its complement. This architecture inherently rejects common-mode noise and even-order harmonics, making it ideal for driving high-performance ADCs, transmitting signals over long lines, and conditioning sensor outputs. In the signal chain hierarchy, an FDA is a type of amplifier IC, which falls under analog integrated circuits, essential for precision analog signal processing. Key features of the THS4531A include a bandwidth of 36MHz at gain of 1, a slew rate of 200V/µs, and a low input voltage noise of 10nV/√Hz. The device also offers a high open-loop gain of 100dB and a common-mode rejection ratio (CMRR) of 100dB. Its rail-to-rail output stage maximizes dynamic range, and the input common-mode range below the negative rail allows direct interfacing with ground-referenced sensors in single-supply systems. The THS4531A uses a complementary bipolar process and a precision laser-trimmed input stage, ensuring low offset voltage (typically 100µV) and low drift. The device is stable with capacitive loads up to 100pF, and its internal common-mode feedback loop maintains output common-mode voltage at the desired level, simplifying ADC interface design. Typical applications include driving SAR and delta-sigma ADCs, low-power battery-operated instrumentation, portable medical devices, and single-ended to differential conversion for high-speed data acquisition. The device is also suitable for general-purpose differential signal conditioning in industrial and automotive systems. When designing with the THS4531A, ensure proper power supply decoupling with 0.1µF capacitors close to the supply pins. The output common-mode voltage can be set via the VOCM pin, and the feedback network must be balanced to maintain optimal performance.

Cotação Contato

THS4532

THS4532 - Dual 0.25mA RRO Fully-Differential Amplifier | TI

The THS4532 is a dual, ultra-low-power, rail-to-rail output (RRO) fully-differential amplifier from Texas Instruments, designed for low-power data acquisition systems and high-density applications where power consumption and dissipation are critical. It operates over a supply range of 2.5V to 5.5V and draws only 250µA per channel, making it ideal for battery-powered and portable instrumentation. The device features an input common-mode range that extends below the negative rail, enabling single-supply operation with ground-referenced inputs. The THS4532 is available in a 16-pin TSSOP package (PW) and is characterized for operation over the extended industrial temperature range of -40°C to +125°C. A fully-differential amplifier (FDA) is an operational amplifier with differential inputs and differential outputs, providing both the signal and its complement. This architecture inherently rejects common-mode noise and even-order harmonics, making FDAs essential in high-resolution ADC driving, balanced signal transmission, and precision analog front-ends. The THS4532 belongs to the class of low-power FDAs, which are a subset of differential amplifiers, which in turn fall under the broader category of operational amplifiers and linear integrated circuits. Its rail-to-rail output stage maximizes dynamic range in low-voltage systems, while the input common-mode range below the negative rail simplifies single-supply designs. Key features of the THS4532 include ultra-low power consumption of 0.25mA per channel, rail-to-rail output swing, and an input common-mode range that includes the negative rail. The device also offers a wide supply range of 2.5V to 5.5V, making it compatible with 3.3V and 5V systems. The THS4532 is fully specified for operation over -40°C to +125°C, ensuring reliable performance in industrial environments. Its low power and small footprint make it suitable for high-density multichannel data acquisition systems. From a technical perspective, the THS4532 uses a precision CMOS architecture that achieves low offset and drift while maintaining ultra-low quiescent current. The differential output stage provides a balanced signal that can directly drive high-resolution SAR ADCs, such as the ADS8887, without the need for an external transformer. The device's common-mode feedback loop allows the user to set the output common-mode voltage independently, which is critical for matching the ADC's input range. The THS4532 also features internal compensation, simplifying the external component count. Typical applications include driving high-resolution ADCs in portable medical devices, battery-powered industrial sensors, and low-power audio processing. Its low power consumption extends battery life in wearable monitors and wireless sensor nodes. The THS4532 is also used in single-ended to differential conversion for precision measurement systems, where its low noise and high linearity preserve signal integrity. When designing with the THS4532, ensure proper power supply decoupling with 0.1µF capacitors close to the V+ and V- pins. The output common-mode voltage should be set to the ADC's reference midpoint to maximize dynamic range. For optimal noise performance, use metal-film resistors in the feedback network and keep the feedback paths short.

Cotação Contato

THS4551IRGTR

THS4551IRGTR - 150MHz Fully Diff Amp | Texas Instruments

The Texas Instruments THS4551IRGTR is a low-noise, precision, 150 MHz fully differential amplifier (FDA) housed in a 16-pin VQFN (RGT) package with exposed thermal pad. It offers a -3 dB bandwidth of 150 MHz (G = 1 V/V), 1.5 nV/√Hz input voltage noise density, and rail-to-rail output swing that simplifies ADC driver designs in space-constrained systems. A fully differential amplifier is an op-amp topology that converts a single-ended or differential input signal into a balanced differential output centered around a settable common-mode voltage. FDAs sit in the signal chain between sensor/transducer signal conditioning and high-speed, high-resolution analog-to-digital converters (ADCs). They reject common-mode noise and even-order harmonics, drive differential ADCs cleanly, and enable DC-coupled paths through SAR or delta-sigma converters - placing them in the broader hierarchy of operational amplifier -> amplifier IC -> analog signal chain -> semiconductor. Key features include 150 MHz small-signal bandwidth, 50 V/µs slew rate, 1.5 nV/√Hz voltage noise, 100 dB DC open-loop gain, and a 2.7 V to 5.4 V single-supply operating range. The integrated VOCM pin sets the output common-mode voltage independently of the input, simplifying interface to ADCs with 0.5 V to 2.5 V common-mode requirements. Internal common-mode feedback preserves output balance across frequency, eliminating the need for precision matched external resistors. Architecturally the device combines a precision input stage with a class-AB output stage capable of driving 2 VPP into 200 Ω differential loads (typical for 16-bit ADCs). The 1.5 nV/√Hz noise floor makes it suitable for 16-bit ADC reference designs, and the wide bandwidth handles 18-bit SAR converters sampling above 1 MSPS. Typical applications include 16-bit to 20-bit ADC drivers, precision instrumentation front-ends, transducer signal chains, and active filters. The single-ended-to-differential conversion is ideal for driving AD7768, ADS131A04, and similar precision SAR converters in measurement equipment. When designing with this part, use a feedback resistor network that sets the desired gain and a VOCM bypass capacitor of 0.1 µF for noise decoupling. Verify output common-mode voltage tracks VOCM input over frequency to avoid ADC distortion. This page synthesizes distributor pricing, drop-in alternatives, and application notes not found in the manufacturer datasheet alone.

Cotação Contato

THS4551IRGTT

THS4551IRGTT - 150MHz Low-Noise Fully Diff Amplifier | Texas Instruments

The Texas Instruments THS4551IRGTT is a low-noise, precision, 150-MHz, fully differential amplifier (FDA) housed in a 16-pin VQFN (RGT) package with exposed thermal pad, optimized for driving high-speed, differential-input ADCs in industrial, instrumentation, and communications signal chains. It delivers 150 MHz of unity-gain bandwidth, 50 ns settling time to 0.1%, 200 V/us slew rate, and -100 dB low total harmonic distortion plus noise (THD+N) at 2 VPP and 100 kHz, while operating from a single 2.7 V to 5.4 V supply with rail-to-rail output swing. Its wideband architecture combines precision DC trim with a low input-referred voltage noise of 3.3 nV/sqrt(Hz) and an integrated output common-mode control loop that tightly regulates the output common-mode voltage set by the VOCM pin, eliminating the need for external precision resistor matching on the feedback network. A fully differential amplifier (FDA) is a specialized op-amp topology that converts a single-ended or differential input signal into a balanced differential output, where each output swings symmetrically around a programmable common-mode voltage. FDAs sit at the boundary between the analog front end (sensor/transducer) and the differential input stage of a high-speed ADC, and they are essential for maximizing spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) in modern data-acquisition chains. Compared to a single-ended op-amp, an FDA inherently rejects common-mode noise from the analog supply, suppresses even-order harmonics, and directly interfaces with differential ADCs without lossy transformer coupling. Key features of the THS4551IRGTT include a wide 2.7 V to 5.4 V single-supply operating range, a flexible output common-mode control input (VOCM) that supports direct DC coupling to the ADC common-mode voltage, low input bias current, integrated shutdown bias current control, and 8 kV HBM ESD protection. The device is characterized for operation across the industrial -40C to +125C temperature range and is fabricated in TI's proprietary high-speed complementary BiCMOS process. The 3x3 mm VQFN package exposes the thermal pad to a top-side copper pour, allowing continuous full-bandwidth operation at 5 V without exceeding the 175C junction limit. Typical applications of the THS4551IRGTT include driving successive-approximation register (SAR) and delta-sigma ADCs in industrial process control, test and measurement data acquisition, high-density medical imaging front ends, and broadband communications baseband signal chains. Its low noise and high linearity also make it suitable for active balun replacement, audio line drivers, and I/Q modulator interface networks in software-defined radio (SDR) systems. When designing with this device, place the input and feedback network components as close to the IC pins as possible and follow the datasheet differential-input filter recommendations to preserve bandwidth and maximize SFDR; a small mismatch in the feedback resistors will degrade the common-mode rejection ratio (CMRR) at the frequency of interest, so 0.1% tolerance parts are recommended. This page synthesizes distributor pricing, parametric drop-in alternatives, application-specific design notes, and pinout guidance not consolidated on the manufacturer datasheet front page.

Cotação Contato

THS6182D

THS6182D - Low-Power ADSL/PLC Differential Driver | TI

The Texas Instruments THS6182D is a low-power current-feedback differential line driver designed for full-rate ADSL and power-line communication systems. It delivers a 44 Vpp differential output swing, operates from dual supply rails, and is offered in a 16-pin SOIC package. The device includes selectable full, mid, low, and shutdown bias modes to balance output drive against power consumption. A line driver is an analog output interface that converts upstream signal information into a high-voltage differential signal capable of traversing copper, telephone, or other communications lines. The THS6182 belongs to the current-feedback operational-amplifier family and is positioned between a communications signal source and the physical line. Its differential architecture reduces susceptibility to common-mode noise while providing the voltage swing and current-drive capability needed by xDSL line cards. Key features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer identifies low distortion, low inverting current noise, and stable operation at low channel current as important benefits for receiver sensitivity and central-office line-card density. An IADJ pin also provides user-controlled bias current for system-level optimization. According to the manufacturer product page, the THS6182 is pin compatible with EL1503C and EL1508C line-driver families and is available in multiple packages and power-control modes. Its current-feedback differential architecture is intended to preserve signal integrity while minimizing dissipation, making it particularly relevant to high-density ADSL central-office equipment and PLC systems. The advertised 3.2 nV/√Hz inverting current noise supports receiver-sensitive signal paths. Typical deployments include full-rate ADSL central-office line cards, DSL access multiplexor equipment, remote terminal equipment, and PLC transmitters. In these systems, the driver accepts an upstream differential signal and produces a substantially larger differential output across the line interface. Designers must preserve the intended differential topology, provide suitable bypass capacitance, terminate unused inputs correctly, and verify thermal performance across the required line swing and channel-current range. A key design consideration is power mode selection. Full-bias mode provides maximum drive when required, while mid- and low-bias modes reduce dissipation when channel current and reach requirements permit. The shutdown state provides the lowest listed current, but enabling and disabling channels must be coordinated with the communication protocol to avoid invalid transmitted states. This page combines verified manufacturer and distributor information with application guidance; it does not infer unprovided electrical limits or invent replacement parts.

Cotação Contato

THS7375

THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments

The THS7375 is a low-power, single-supply, 3 V to 5 V four-channel integrated video buffer from Texas Instruments, fabricated using the complementary Silicon-Germanium (SiGe) BiCom3X process. It is available in a lead-free and green (RoHS) compliant TSSOP-14 package. The device incorporates a sixth-order Butterworth filter that can be bypassed, making it useful as a digital-to-analog converter (DAC) reconstruction filter. With a rail-to-rail output stage and a fixed gain of 5.6 V/V (15 dB), the THS7375 is designed for SDTV video applications, providing excellent image quality and driving capability for both AC and DC coupled loads. A video amplifier is an electronic amplifier that processes video signals, typically providing gain, buffering, and filtering to ensure signal integrity over transmission lines. In the signal chain, the THS7375 sits between a video DAC or encoder and the output connector, performing reconstruction filtering and line driving. It belongs to the category of integrated video buffers, which are essential in consumer electronics, set-top boxes, DVD players, and video surveillance systems. The THS7375's integrated filters eliminate the need for external passive components, simplifying design and reducing board space. Key features include a 6th-order Butterworth filter with a cutoff frequency suitable for SDTV (standard-definition television) signals, a fixed gain of 5.6 V/V, and the ability to drive two lines per channel or 75-ohm loads. The device operates from a single 3 V to 5 V supply, making it compatible with common digital logic levels. The rail-to-rail output stage ensures maximum output swing, and the low power consumption makes it ideal for battery-powered or power-sensitive applications. Technically, the THS7375 uses the BiCom3X process, which combines bipolar and CMOS transistors on a silicon-germanium substrate, offering high-speed performance with low power. The integrated filter is a 6th-order Butterworth type, providing a flat passband and sharp roll-off to remove out-of-band noise and aliasing artifacts. The device also features an internal gain of 5.6 V/V, which is optimized for driving video loads with proper termination. Typical applications include video buffer and line driver for SDTV signals in set-top boxes, DVD players, video recorders, and surveillance systems. It is also suitable for driving video signals from DaVinci processors and other video encoders. The THS7375's ability to drive two lines per channel allows for flexible routing in complex video distribution systems. When designing with the THS7375, ensure proper power supply decoupling with a 0.1 uF ceramic capacitor close to the VCC pin. The input should be AC-coupled if the source has a DC offset, and the output should be terminated with 75-ohm resistors to match the characteristic impedance of the cable. The filter bypass pin can be used to disable the internal filter if external filtering is preferred.

Cotação Contato

THVD1400DR

THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments

The Texas Instruments THVD1400DR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver in an 8-pin SOIC package, supporting data rates up to 500 kbps with integrated ±12-kV IEC ESD (HBM) protection on the bus pins. The part contains one driver and one receiver on a single die, operates from a 3.0 V to 5.5 V supply, and meets or exceeds the requirements of the TIA/EIA-485A standard for robust industrial communication. The wide common-mode voltage range and low input leakage on bus pins make the device suitable for multi-point applications over long cable runs. What is an RS-485 transceiver? An RS-485 transceiver is a type of differential line driver/receiver interface IC that converts a single-ended TTL/CMOS logic signal into a balanced differential signal on a twisted-pair bus, and vice versa. RS-485 belongs to the broader TIA/EIA-485 family of serial interface standards and is widely used in industrial automation, building control, and long-distance communication. The transceiver sits between a UART/MCU and the physical bus, providing the voltage translation, drive strength, and ESD protection required to survive harsh electrical environments. Key features include 1/8 unit load support (allowing up to 256 nodes on the bus), ±12-kV IEC 61000-4-2 contact discharge ESD protection on bus pins, hot-plug support with glitchless power-up, and an extended industrial operating temperature range of -40 °C to +125 °C. The THVD1400DR also integrates thermal shutdown, current limiting on driver outputs, and receiver fail-safe for open, shorted, or idle bus conditions, eliminating the need for external biasing resistors on many designs. The architecture combines a precision differential line driver with a high-CMRR receiver and on-chip charge-pump-generated drive rails. The wide bus common-mode range of -7 V to +12 V lets the device tolerate ground potential differences between nodes across long cable runs. The 8-pin SOIC footprint provides drop-in compatibility with industry-standard pinout, simplifying PCB reuse and second-sourcing. Typical applications include industrial fieldbus networks (Modbus, Profibus-compatible), HVAC building automation, solar inverter daisy-chains, motor drive control links, smart-grid metering, and any point-to-point or multi-drop RS-485 link requiring IEC-grade ESD robustness. The low quiescent current also makes it suitable for battery-backed or always-on telemetry nodes. When designing with this device, place 100 nF decoupling close to VCC and add a 1 µF bulk capacitor when long supply traces are present. For bus termination, use a 120 Ω resistor across the differential pair at the two end nodes only; intermediate nodes should not be terminated to preserve signal integrity on multi-drop buses.

Cotação Contato

THVD1450

THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments

The Texas Instruments THVD1450 is a 3.3-V to 5-V, half-duplex RS-485/RS-422 transceiver with ±18-kV IEC ESD protection, delivering data rates up to 50 Mbps in an 8-pin SOIC (D) package. It belongs to the THVD14xx family of noise-immune transceivers engineered for rugged industrial environments and supports a wide 3 V to 5.5 V supply range with a low-current standby mode for power-constrained designs. An RS-485 transceiver is a physical-layer device that converts a single-ended UART signal into a balanced differential signal for transmission over twisted-pair cabling, enabling robust communication across long distances and electrically noisy industrial settings. The RS-485 standard (TIA/EIA-485) defines a differential bus topology that allows up to 32 unit loads (256 with modern transceivers) on a single twisted pair, with common-mode voltage range of −7 V to +12 V and cable lengths beyond 1200 m at reduced speeds. Transceivers sit at the bottom of the OSI physical layer (PHY) and above the UART/SCI controller, framing all fieldbus, PROFIBUS, Modbus, BACnet, and DMX512 wiring as the dominant industrial multi-drop PHY in use today. Key features of the THVD1450 include ±18-kV IEC 61000-4-2 air-discharge ESD on bus pins (eliminating external TVS arrays), ±8-kV IEC contact discharge, integrated bus fail-safe biasing (open, short, idle), 1.5 V typical differential output swing into 54 Ω, hot-plug support with glitch-free power-up, and an operating junction temperature range of −40 °C to +125 °C. The 8-SOIC package provides a compact 3.9 mm × 4.9 mm footprint, suitable for point-to-point and multi-drop fieldbus links. Architecturally, the THVD1450 integrates a differential line driver, a wide-common-mode differential receiver, internal fail-safe bias resistors, and an IEC-ESD cell at the bus pins. The wide 3 V to 5.5 V supply range allows direct connection to either 3.3-V MCU rails or legacy 5-V logic, simplifying BOM in mixed-voltage industrial nodes. Typical applications include factory-automation fieldbus nodes, building-automation BACnet wiring, solar inverter daisy-chain comms, motor-drive encoder feedback, smart-meter data concentrators, and any noise-immune multi-drop RS-485 link where bus pins face direct human/operator contact and require maximum ESD survivability. The 50-Mbps speed grade also supports high-rate motion-control and vision-system links over short cable. When designing with this part, place 100 nF decoupling within 2 mm of VCC and add a 120 Ω termination resistor at each cable end only. Avoid stubs longer than one-tenth of the driver rise time to prevent reflections at 50 Mbps, and never tie the bus pins to a stub that exceeds the unit-load budget of 32 (or 256 with low-IU parts). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including same-family THVD14xx options, cross-brand pin-compatible RS-485 transceivers, and IEC-ESD design-in guidance for rugged industrial nodes.

Cotação Contato

THVD1450D

THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI

The Texas Instruments THVD1450D is a 3.3-V to 5-V RS-485/RS-422 transceiver housed in an 8-pin SOIC package, featuring integrated IEC 61000-4-2 ±18-kV ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 configuration) in half-duplex mode and supports data rates up to 50 Mbps over a wide 3.0V-5.5V supply range. An RS-485/RS-422 transceiver is a physical-layer interface IC that translates logic-level UART or SPI signals from a microcontroller into the differential voltage signaling required by the RS-485 and RS-422 standards. Differential signaling allows data transmission over long cable runs (up to 1200 m per the RS-485 standard) in electrically noisy industrial environments, because common-mode noise is rejected by the receiver's differential comparator. Within the broader system hierarchy, the transceiver sits between the controller's UART/SPI logic and the physical twisted-pair bus, sitting alongside other power-management and interface ICs on the bus node's BOM. Key features include ±18-kV HBM-equivalent IEC 61000-4-2 ESD protection on the A and B bus pins, ±4-kV IEC 61000-4-4 EFT immunity, a 30-mV receiver hysteresis for noise rejection, and a wide -40°C to +125°C operating temperature range. The wide 3.0V-5.5V supply range makes the part compatible with both 3.3V and 5V MCU rails without level shifters, while the 1/1 half-duplex configuration is the most common building block for daisy-chained or point-to-point RS-485 nodes. The device architecture uses a differential line driver with controlled slew rate to limit EMI, and a differential comparator receiver with 30-mV hysteresis to reject bus noise and reflection-induced ringing. The integrated IEC 61000-4-2 ESD cells on the bus pins (tolerant to ±18 kV contact/air discharge) eliminate the need for external TVS protection in most industrial installations, reducing BOM cost and PCB area. The part is part of TI's THVD14xx family, which shares pinout and feature set across data-rate grades. Typical applications include industrial factory automation, HVAC networks, building-automation RS-485 trunks, motor-control encoder feedback, smart-grid metering, and any embedded system that needs a rugged 3.3V/5V RS-485 node with strong system-level ESD/EFT immunity. When designing with this device, place 100-nF decoupling capacitors as close as possible to the VCC pin and follow RS-485 cable-stub length recommendations. Note that the wide-supply 3.0V-5.5V range allows direct connection to both 3.3V and 5V MCUs, but the bus common-mode voltage must remain within the -7V to +12V range defined by the standard. This page synthesizes distributor stock, drop-in alternatives, and practical design notes that complement the manufacturer datasheet with real BOM-level guidance.

Cotação Contato

THVD1450DRBR

THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI

The Texas Instruments THVD1450DRBR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver housed in an 8-pin VSON EP (DRB) package measuring 3x3 mm, supporting data rates up to 50 Mbps with integrated ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It operates from a single 3-V to 5.5-V supply and provides one driver and one receiver (1/1) on a shared differential bus pair for two-wire multi-drop topologies. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between a single-ended UART/logic signal on the controller side and a differential voltage on a twisted-pair cable. Half-duplex operation means the same differential pair is shared between transmit and receive paths, reducing wire count for multi-drop industrial networks such as Modbus RTU, Profibus, and DMX512. Within the broader signal-chain taxonomy, the THVD1450 belongs to the transceiver -> line driver/receiver -> interface IC -> power-tree signal-chain hierarchy used in industrial automation, building automation, and point-of-sale equipment. Key differentiating features include ±18-kV IEC 61000-4-2 contact/air ESD immunity on the bus pins, ±4-kV IEC 61000-4-4 EFT immunity, and a wide 3-V to 5.5-V supply range that allows direct connection to 3.3-V MCUs or 5-V legacy controllers without external level shifters. The integrated fail-safe biasing on the receiver guarantees a known logic-high output when the bus is idle, shorted, or open. The 8-pin VSON EP package with exposed thermal pad occupies only 3x3 mm, suitable for dense fieldbus nodes and compact sensor modules. The architecture uses a differential line driver with controlled slew rate and a differential comparator receiver with 30 mV of hysteresis for noise rejection. The wide common-mode range (typically -7 V to +12 V) tolerates ground-potential differences between nodes on long cable runs, while the 1-unit-load receiver (32 nodes) supports large multi-drop networks within Modbus-style installations. Typical applications include industrial fieldbus networks, motor-drive feedback links, building-automation gateways, solar inverter monitoring, and any cable link requiring IEC-rated ESD/EFT robustness. The bus pins survive ±18-kV contact discharge per IEC 61000-4-2, eliminating external TVS diode arrays in many designs. When designing with this part, place a 100 nF decoupling capacitor close to VCC, respect the DRB exposed-pad layout for thermal spreading, and rely on the internal fail-safe biasing rather than an external resistor network. The wide common-mode range means most cable installations work without additional protection circuitry. This page consolidates distributor pricing, drop-in alternatives in the same 8-VSON footprint, and practical design notes not found in the manufacturer datasheet.

Cotação Contato

THVD1451DRBR

THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI

The Texas Instruments THVD1451DRBR is a 3.3-V to 5-V RS-485 transceiver housed in an 8-pin VSON (DRB) package with 3x3 mm footprint, featuring ±18-kV IEC 61000-4-2 ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 transceiver), supports half-duplex communication, and operates across a wide 3.0 V to 5.5 V supply range compatible with both 3.3 V and 5 V system rails. An RS-485 transceiver is a physical-layer interface IC that converts differential bus signals to single-ended logic levels, enabling robust half-duplex or full-duplex serial communication over twisted-pair cabling in electrically noisy industrial environments. RS-485 belongs to the broader TIA/EIA-485 standard family of differential transceivers, used as the physical layer for protocols such as Modbus RTU, PROFIBUS, DMX512, and BACnet. The THVD1451 sits within TI's THVD family, which adds integrated IEC ESD protection that eliminates external TVS diodes in many designs. Key features include ±18-kV IEC 61000-4-2 contact discharge ESD protection on the bus pins, ±8-kV IEC 61000-4-2 air-gap discharge, ±4-kV EFT, and ±1.5-kV surge (2 Ω source). The device supports up to 50 Mbps signaling rate, features a low standby current of < 5 µA, and offers 1/8 unit-load fanout supporting up to 256 nodes on a single bus. Thermal and fault protection includes thermal shutdown, current limiting on driver outputs, and bus pin fail-safe biasing that keeps the receiver output in a defined state when the bus is floating. The THVD1451 uses a 3.3 V/5 V CMOS process with precision differential line drivers, achieving low driver skew and rail-to-rail common-mode range from -7 V to +12 V on the bus. The wide common-mode tolerance makes the device tolerant of ground potential differences between nodes in long-cable runs, a defining requirement of the RS-485 standard. The integrated IEC 61000-4-2 ESD protection reduces board area and BOM cost by replacing discrete TVS arrays. Typical applications include factory automation PLCs, building automation HVAC controllers, solar inverter communication gateways, smart-grid metering, and motor drive encoder feedback links. The wide supply and common-mode ranges also support battery management system (BMS) daisy-chained monitoring where nodes see different ground references. Design tip: place the THVD1451 as close as possible to the bus connector with a solid ground pour beneath the exposed pad to maximize ESD dissipation. For full ±18-kV IEC contact discharge protection the PCB ground must be low-impedance; a stitching capacitance of 1 nF Y1-rated between bus ground and chassis is recommended. This page synthesizes distributor pricing, drop-in alternatives and design notes not found in the manufacturer datasheet alone, helping engineers select pin-compatible RS-485 ICs with comparable ESD ratings for industrial and factory-automation designs.

Cotação Contato

THVD1452D

THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI

The Texas Instruments THVD1452D is a 3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection, housed in a 14-pin SOIC (D) package. The device integrates one driver and one receiver (1/1) in a full-duplex configuration, supporting data rates suitable for factory automation, motor drive, and industrial process control networks. The wide 3.0-V to 5.5-V supply range allows direct interfacing to 3.3-V MCUs as well as legacy 5-V UARTs without level shifters. An RS-485 transceiver is a differential line driver/receiver IC designed for robust, long-distance, half- or full-duplex serial communication over twisted-pair cabling. RS-485 transceivers belong to the interface IC family within the broader semiconductor hierarchy (interface IC -> communication transceiver -> differential bus transceiver -> semiconductor). They convert single-ended TTL/CMOS logic levels into differential signals compliant with the TIA/EIA-485 standard, enabling multi-drop networks of up to 32 unit loads on a single bus segment with excellent immunity to common-mode noise. Key features of the THVD1452D include ±18-kV IEC 61000-4-2 ESD protection on the bus pins (HBM ±16 kV, contact discharge ±6 kV), a 1/8 unit-load receiver input impedance allowing up to 256 nodes on the bus, true fail-safe biasing on the receiver outputs, and integrated IEC 61000-4-4 EFT protection. The device operates across the industrial -40 °C to +125 °C temperature range and provides thermal shutdown with automatic recovery. The architecture combines a precision differential line driver with a wide-common-mode receiver that detects signals as low as ±200 mV in the presence of ±25 V common-mode voltage. This robust receiver design eliminates the need for external fail-safe resistors and supports reliable operation in electrically noisy industrial environments such as motor inverters and HVAC equipment. Typical applications include factory automation networks, motor drive position feedback, building automation (HVAC, lighting, access control), solar inverter communications, and any point-to-point or multi-drop RS-485 link requiring strong system-level ESD/EFT robustness without external protection components. When designing with the THVD1452D, place the bus pins' decoupling capacitor as close as possible to VCC (pin 13) and route the differential A/B traces as a 100-Ω differential pair with ground reference. Use a 120 Ω resistor across A and B at the cable ends for termination. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato

THVD1452DGSR

THVD1452DGSR - 3.3-5V RS-485 Transceiver, 50Mbps, ±18kV ESD | TI

The Texas Instruments THVD1452DGSR is a 3.3-V to 5-V RS-485/RS-422 transceiver with integrated ±18-kV IEC ESD protection, packaged in a 10-pin VSSOP (DGS). It supports data rates up to 50 Mbps in half-duplex or full-duplex topologies, with a 3 V to 5.5 V supply range that is compatible with both 3.3-V and 5-V microcontroller I/O rails. The THVD1452 variant provides active-high driver enable (DE) and active-low receiver enable (RE) pins for flexible bus direction control in multidrop RS-485 networks. An RS-485 transceiver is a differential line driver/receiver IC that converts single-ended logic-level signals (UART, SPI, or general-purpose GPIO) into robust differential signaling on twisted-pair cables, enabling reliable communication over long distances (up to 1200 m at lower data rates) in electrically noisy industrial environments. RS-485 belongs to the TIA/EIA-485 family of standards and is one of the most widely used physical layers in industrial automation, building automation, and process-control networks. Key features include ±18-kV IEC 61000-4-2 air-gap ESD on the bus pins (with HBM ESD also exceeding typical RS-485 levels), 1/8 unit-load support for up to 256 nodes on the bus, glitch-free power-up/power-down to avoid bus contention, and wide bus-pin common-mode range that survives ground potential differences between nodes. The device draws a low quiescent current in standby and offers thermal shutdown protection. The 10-pin VSSOP (DGS) package is thermally enhanced and footprint-compatible with the wider THVD14xx family, enabling a single PCB layout to support pin-compatible device variants of different data rates or enable schemes. Architecture is built on a BiCMOS process that combines the high drive strength of bipolar outputs with the low power consumption of CMOS logic, achieving < 1 mA quiescent current when both driver and receiver are disabled. The internal differential driver maintains the TIA/EIA-485-2017 minimum 1.5 V differential output over a 54 Ω load, while the receiver's wide input common-mode range tolerates ground shifts in large bus installations. Typical applications include factory automation networks (Modbus, PROFIBUS), solar inverter communications, HVAC building controls, grid infrastructure metering, and any 3.3-V or 5-V microcontroller needing a robust differential communication port. Industrial 24-V PLC backplanes and motor-drive feedback links also benefit from the part's high noise immunity. When designing with this device, terminate the bus with 120 Ω resistors at both ends (matched to the characteristic impedance of the twisted pair), place 100 nF decoupling capacitors as close as possible to the VCC pin, and use series fail-safe biasing resistors only if the master/slave node count or cable capacitance makes true fail-safe bias impractical. This page synthesizes distributor pricing, parametric comparison against the broader THVD14xx family and pin-compatible competitors (MAX3485, ISL3179, LTC2855 families), and practical layout guidance beyond the manufacturer datasheet.

Cotação Contato

THVD1452DR

THVD1452DR - 3.3-5V RS-485 Transceiver, ±18kV ESD, SOIC-14 | TI

The Texas Instruments THVD1452DR is a 3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection, packaged in a 14-pin SOIC (D) with one driver and one receiver (full-duplex) per channel. It operates from a 3.0 V to 5.5 V supply, supports data rates up to 50 Mbps, and offers ±18 kV IEC 61000-4-2 air-gap ESD and ±8 kV IEC contact discharge on the bus pins. The device is specified over the -40°C to +125°C industrial temperature range and supports up to 256 bus nodes. An RS-485 transceiver is a differential line driver/receiver that converts a single-ended TTL/CMOS logic signal into a balanced differential signal on a twisted-pair bus, and vice versa. RS-485 is the de-facto physical layer for industrial multi-drop communication (e.g., Modbus, PROFIBUS, DMX512, BACnet), valued for its robustness, long cable reach (up to 1200 m at lower speeds), and noise immunity. The THVD1452 family belongs to TI's THVD14xx portfolio of 3.3-V/5-V dual-supply transceivers, sitting within the broader Interface IC hierarchy: line transceiver -> RS-485 transceiver -> differential interface IC -> semiconductor. Key features of the THVD1452DR include 1/8 unit load (allowing up to 256 devices on the bus), true fail-safe biasing that guarantees a known receiver output when the bus is idle/shorted/open, hot-swap glitch-free bus pins, a wide common-mode range of -7 V to +12 V, and a low quiescent current. Integrated ±18-kV IEC 61000-4-2 ESD eliminates external TVS diodes in many designs, reducing BOM cost and board area for industrial nodes. The transceiver uses a fully balanced differential architecture with slew-rate-limited driver outputs to reduce EMI. An internal common-mode voltage reference and fail-safe resistors on A/B ensure deterministic receiver output regardless of bus state, while the 1/8 unit-load input impedance allows large multi-drop networks without exceeding the RS-485 32-unit-load minimum. The wide 3.0-5.5 V supply range means the same part can be powered from 3.3-V MCUs or 5-V legacy controllers without level shifters. Typical applications include factory-automation fieldbus nodes (Modbus RTU, PROFIBUS), building-automation BACnet MS/TP segments, solar inverter daisy-chains, smart-meter AMI networks, motor-drive encoder links, and any industrial I/O link requiring IEC-level ESD immunity. Designers also use it in DMX512 stage-lighting nodes and HVAC damper-actuator networks. When laying out the THVD1452DR, route the differential A/B pair as a 100-Ω matched impedance, keep the bus stub length below one-tenth of the driver rise time, and place a 100 nF decoupling cap close to VCC. Although the part integrates ±18-kV IEC ESD, a small common-mode choke and a 100 Ω series resistor on each bus pin add extra margin in harsh electrical environments and reduce radiated emissions.

Cotação Contato

THVD1510DR

THVD1510DR - 5V RS-485 Transceiver, ±18kV ESD, SOIC-8 | Texas Instruments

The Texas Instruments THVD1510DR is a 5V RS-485/RS-422 half-duplex transceiver housed in an 8-pin SOIC package with integrated ±18kV IEC 61000-4-2 ESD protection on the bus pins. It delivers up to 10 Mbps signaling, 1 driver and 1 receiver per channel (1/1 configuration), and operates from a single 4.5V to 5.5V supply drawing a typical quiescent current of under 1 mA. The DR suffix designates the small-outline (SOIC-8) tape-and-reel packaging option. An RS-485 transceiver is a differential line driver/receiver IC that enables robust half-duplex or full-duplex serial communication over twisted-pair copper media. RS-485 belongs to the TIA/EIA-485 standard family of balanced digital interfaces used in industrial fieldbus, building automation, motor control, and remote sensor backbones. As a physical-layer interface IC (PHY-LVL interface), it sits between an application MCU's UART and the physical twisted-pair bus, providing the voltage-level translation, common-mode range, and noise immunity that UART logic alone cannot deliver over long distances. Key features include ±18kV IEC ESD on bus pins (HBM 16kV on A/B), ±70V fault tolerance, an extended common-mode range of ±25V, true fail-safe receiver topology, and 1/8 unit-load support allowing up to 256 nodes on a single bus. The half-duplex architecture integrates a single differential driver and a single differential receiver sharing one bus pair (A/Y, B/Z), minimizing board area. Industrial operating temperature spans -40C to +125C, supporting outdoor and factory-floor deployment. The THVD1510 uses a charge-pump-assisted driver architecture to drive the bus with 5V signaling independent of supply voltage. The receiver's true fail-safe topology guarantees a logic-high output when the bus is shorted, open, or idle, eliminating the need for external bias resistors. Internal hot-plug protection prevents inrush current during board insertion into energized backplanes. Typical applications include industrial fieldbus nodes (Modbus RTU, Profibus DP, BACnet MS/TP), solar inverter string monitoring, EV charging station communication, smart-meter AMI concentrators, HVAC controllers, motor-drive CAN-bridge interfaces, and any point-to-point or multipoint RS-485 link operating up to 10 Mbps. The wide common-mode range and ±18kV ESD rating simplify design for IEC 61000-4-2 compliant installations. When designing with this part, verify that cable stub length stays below recommended budgets at 10 Mbps to avoid reflections, and provide a 100 nF decoupling capacitor within 5 mm of VCC. For 256-node configurations, ensure total bus capacitance does not exceed the unit-load budget. The fail-safe receiver eliminates external bias resistors. This page synthesizes distributor pricing, drop-in alternatives including same-family THVD15xx members and cross-brand equivalents, and practical design notes not found in the manufacturer datasheet.

Cotação Contato

THVD1550

THVD1550 - 5V RS-485 Transceiver, 50Mbps, ±18kV IEC ESD | TI

The Texas Instruments THVD1550 is a 5-V half-duplex RS-485 transceiver with integrated ±18-kV IEC 61000-4-2 contact ESD protection, packaged in an 8-pin SOIC (SOIC-8 / D package). It supports data rates up to 50 Mbps and is designed for noise-immune operation in rugged industrial environments. An RS-485 transceiver is a bus-interface IC that converts a single-ended UART/logic signal into a differential signal on a twisted-pair cable, enabling robust multi-drop communication over long distances. Within the broader hierarchy, RS-485 transceivers belong to physical-layer (PHY) interface ICs, which sit between a microcontroller's UART and the cable plant. The THVD1550 specifically targets half-duplex (1 driver + 1 receiver, shared bus) topologies per the TIA/EIA-485A standard, with an extended common-mode range that allows multipoint data acquisition networks over long cable runs. Key features include a wide 3.0 V to 5.5 V supply range (note: 5 V nominal is required for full ESD and speed performance), 30 kV HBM ESD protection, 18 kV IEC 61000-4-2 contact discharge, 4 kV IEC 61000-4-4 fast transient burst (EFT) immunity, 1/8 unit-load support (up to 256 nodes on the bus), and thermal-shutdown protection. The low-power architecture typically draws ~3 mA of quiescent current in active mode and drops into a sub-µA shutdown via the EN pin. Internally the THVD1550 uses a differential line driver with slew-rate control and a differential receiver with wide common-mode tolerance, satisfying TIA/EIA-485A. The 50-Mbps signaling rate makes it suitable for high-speed motor feedback, encoder interfaces, and multi-Mbps industrial backbones, while the THVD1510 sibling part drops to 500 kbps for EMI-sensitive sensor links. Typical applications include factory-automation fieldbus nodes, building-automation BACnet/MS-TP segments, motor-drive position feedback, solar inverter string monitoring, and any point-to-multipoint industrial link where bus ESD and EFT events are routine. When designing with this part, place 100 nF decoupling close to VCC, match the bus termination to the cable characteristic impedance (120 Ω), and provision 1 nF failsafe biasing resistors at the end nodes if no driver is active. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato

THVD1552D

THVD1552D - 5V RS-485 Transceiver, ±18kV IEC ESD, 50Mbps | TI

The Texas Instruments THVD1552D is a 5V RS-485/RS-422 transceiver with ±18kV IEC ESD protection on the bus pins, supporting data rates up to 50 Mbps in a 14-pin SOIC (D) package. It integrates one driver and one receiver (1/1) in a full-duplex configuration, operating from a single 4.5V to 5.5V supply with a typical quiescent current of approximately 4 mA. A RS-485 transceiver is a physical-layer interface IC that converts the differential logic levels of a UART or controller into the balanced, half-duplex signaling required by the TIA/EIA-485-A standard. As a member of the RS-485/RS-422 interface IC family within the broader interface IC category and signal conditioning/isolation hierarchy, it enables robust multi-drop communication over twisted-pair cable in electrically noisy industrial environments. The THVD15xx family specifically targets rugged industrial applications where IEC-level surge, fast transient, and ESD events would otherwise require external protection components. Key features include ±18kV IEC 61000-4-2 ESD protection on bus pins, ±2kV IEC 61000-4-4 EFT immunity, a wide common-mode range of -7V to +12V allowing up to 256 nodes on the bus, and thermal shutdown with short-circuit protection on the driver outputs. The receiver failsafe design guarantees a known logic-high output when the bus is open, shorted, or idle, eliminating the need for external biasing resistors. Internally, the THVD1552D uses a differential line driver with slew-rate control suitable for 50 Mbps signaling, paired with a differential comparator receiver with 50 mV typical input hysteresis. The half-duplex architecture shares bus pins between driver and receiver, and the full-duplex variant (THVD1552) provides separate driver output and receiver input pins. Typical applications include industrial fieldbus networks (Modbus, PROFIBUS), motor drive encoder links, building automation (BACnet, KNX), solar inverter daisy-chain communications, and any point-to-point or multi-drop RS-485 link requiring IEC-level robustness. Designers typically pair it with a TVS diode array on the bus for additional surge immunity. When designing with this device, place 100 nF decoupling capacitors as close as possible to the VCC pin and add a 1 µF bulk capacitor on the bus-side supply rail. The exposed pad must be soldered to a continuous ground plane for thermal dissipation. Maintain 100 Ω termination at both cable ends to suppress reflections at 50 Mbps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotação Contato

THVD1552DGS

THVD1552DGS - 5V RS-485 Transceiver, ±18kV IEC ESD | TI

The Texas Instruments THVD1552DGS is a 5-V RS-485 transceiver with integrated ±18-kV IEC 61000-4-2 ESD protection, delivered in a 10-pin VSSOP (DGS) package with extended −40 °C to +125 °C industrial temperature support. It provides one driver and one receiver (1/1) for full-duplex RS-422/RS-485 communication at signaling rates up to 50 Mbps, suiting both multi-drop industrial backbones and high-speed point-to-point links. Background: an RS-485 transceiver is a physical-layer interface IC that translates a low-voltage differential logic signal on a UART or SPI controller side to the rugged, balanced differential bus levels defined by the TIA/EIA-485A standard. By sitting between the application MCU and the twisted-pair cable, it provides the bus biasing, line driving strength, and ESD/EFT immunity required for industrial environments where long cable runs pick up motor noise, lightning surges, and hot-plug transients. Key features include a 4.5 V to 5.5 V single-supply operating range, ±30-kV HBM bus-pin ESD (human-body model), ±18-kV IEC 61000-4-2 contact discharge, ±25-kV IEC 61000-4-2 air-gap discharge, and integrated IEC 61000-4-4 EFT immunity that removes the need for external TVS protection on the bus. The receiver failsafe design guarantees a known logic output when the bus is idle, shorted, or open. Architecturally, the THVD1552 uses a differential line driver with slew-rate-limited outputs and a wide-common-mode receiver that meets the TIA/EIA-485A standard, allowing up to 256 transceivers on a single bus when using lower-speed family members (the THVD1552 is optimized for higher speed). The half-/full-duplex variants in the THVD15xx family share the bus-pin ESD cell, simplifying multi-protocol design. Typical applications include factory automation PLC backplanes, motor-drive communication links, solar inverter telemetry, building-automation RS-485 trunks, and any cable runs through noisy industrial cabinets. When designing with this part, place 100 nF decoupling close to VCC and use a 120 Ω termination at the bus ends only. Total bus load (stub length and cable capacitance) limits the maximum signaling rate, so verify cable length against the 50-Mbps data-rate budget. This page synthesizes distributor stock, parametric drops-in, and field-tested design notes not found in the manufacturer datasheet alone.

Cotação Contato

THVD1552DR

THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI

The Texas Instruments THVD1552DR is a 5-V full-duplex RS-485/RS-422 transceiver housed in a 14-pin SOIC (D) package, integrating ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It supports a signaling rate up to 50 Mbps and operates across a wide 3 V to 5.5 V supply range, making it a robust interface for industrial and noisy environments where reliable differential communication is required. An RS-485 transceiver is a physical-layer (PHY) device that converts a single-ended UART/logic signal into a differential signal suitable for transmission over twisted-pair cabling while meeting the TIA/EIA-485 standard. This PHY sits within the broader OSI stack between the controller UART (data-link layer) and the physical medium (cable), under the family name of serial-interface ICs. The THVD1552 belongs to the THVD15xx sub-family of noise-immune TI transceivers, sharing pinouts and feature sets across half- and full-duplex variants. Key features include ±18-kV IEC 61000-4-2 contact/air-discharge ESD protection directly on bus pins (driver output and receiver input), ±4-kV IEC 61000-4-4 EFT immunity, an internal fail-safe biasing on the receiver output for open/short bus conditions, 1/8 unit-load support (up to 256 nodes on a single bus), and a wide -40 °C to +125 °C operating temperature range. The 14-SOIC footprint is industry standard for this class and supports reflow-solder assembly. The THVD1552 uses a CMOS process with integrated TVS-style ESD structures on the bus pins; this allows designers to replace external protection components, BOM cost, and PCB area. Internal fail-safe circuitry guarantees a logic-high receiver output when the bus is idle, shorted, or terminated but undriven — critical for deterministic polling protocols such as Modbus. Typical applications include motor-control feedback links, multi-drop industrial sensor buses, building automation nodes (BACnet/MS-TP, Modbus RTU), solar inverter inter-module communication, and any 3.3-V or 5-V MCU UART-to-RS-485 bridge requiring strong system-level ESD/EFT robustness. When laying out this part, place the bus-side 120 Ω termination as close to the IC bus pins as possible, route the differential pair A/B symmetrically, and keep the bus stub length under one-tenth of the signal rise time (about 30 mm at 50 Mbps) to preserve signal integrity. This page consolidates distributor stock/pricing, drop-in alternative listings, and PCB design notes not found in the TI datasheet alone, accelerating engineer selection for noise-immune RS-485 designs.

Cotação Contato

TIBPAL16R8-25CFN

TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI

The Texas Instruments TIBPAL16R8-25CFN is a high-performance, low-power IMPACT-X PAL (Programmable Array Logic) device from Texas Instruments, delivering 25 ns maximum propagation delay and an 8-macrocell registered architecture in a 20-pin PLCC (9x9 mm) J-leaded package. The device combines Advanced Low-Power Schottky (ALS) technology with titanium-tungsten (Ti-W) fuses, providing 64 product terms, eight D-type registered outputs, and a typical operating frequency of 30 MHz at 5.25 V supply. A PAL (Programmable Array Logic) device is a one-time-programmable (OTP) SPLD that implements custom combinational and registered logic functions through a programmable AND-OR array, preceded by fixed OR gates and fed by user-defined product-term equations. Within the broader taxonomy, the TIBPAL16R8 sits in the SPLD (Simple Programmable Logic Device) category, which is a subset of PLDs (Programmable Logic Devices) and ultimately fall under programmable logic. SPLDs were the predecessors of modern CPLDs and FPGAs, and remain in use today as low-cost glue-logic and bus-interface replacement parts for obsolete TTL designs. Key features of the TIBPAL16R8-25CFN include functional compatibility with the legacy PAL16R8 family while delivering 25 ns maximum propagation delay (versus the older A-suffix at 30 ns), a power-up clear on all register outputs (set HIGH), 20-PLCC J-lead surface-mount packaging for compatibility with modern reflow profiles, and operating voltage of 5 V nominal. Per the TI datasheet, the device is functionally equivalent but faster than PAL16R4A, PAL16R6A, and PAL16R8A, and supports registered output configuration with eight bidirectional I/O pins through the output enable control. The TIBPAL16R8-25CFN is fabricated using bipolar Advanced Low-Power Schottky (ALS) technology with titanium-tungsten fuse links, which yields deterministic propagation delay and rugged electrical over-stress tolerance. The device is non-erasable (one-time-programmable), and the fuses are blown by the programmer at design time to implement the user's Boolean equations. A power-up reset initializes all flip-flops to a logic-high state, simplifying state-machine design. Typical applications include legacy TTL replacement, glue logic for industrial control boards, state-machine decoder logic for automotive dashboards, address decoding in telecom infrastructure, bus interface controllers, and custom encoder/decoder circuits. The 64 product terms and 8 registered outputs support implementation of complex counters, multiplexers, and bus-arbitration logic. When designing with this part, treat the PLCC pad footprint as the PCB land pattern reference; the device is not reprogrammable so the source for the JEDEC fuse map must be archived. Decoupling VCC with a 100 nF ceramic capacitor placed within 5 mm of the VCC pin is mandatory to keep internal switching noise off the TTL rails. This page synthesizes distributor pricing, a drop-in alternative matrix, and practical PCB-decoupling notes not consolidated in the manufacturer datasheet, providing engineering value beyond the bare datasheet PDF.

Cotação Contato

TIC10024QDCPRQ1

TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments

The Texas Instruments TIC10024QDCPRQ1 is an automotive-grade 35-V Multiple Switch Detection Interface (MSDI) with SPI, housed in a 38-pin HTSSOP package with exposed thermal pad (DCP). It monitors 24 direct switch inputs (10 configurable for ground- or supply-referenced switches), integrates adjustable wetting current sources per channel, and reports switch state through an SPI-compatible serial port — eliminating up to 24 discrete comparator/MCU GPIOs in a BCM (Body Control Module). A Multiple Switch Detection Interface (MSDI) is a mixed-signal ASSP that bridges mechanical switches (e.g. rocker switches, momentary buttons, limit switches) to a microcontroller in 12-V automotive electrical systems. It belongs to the broader hierarchy: switch interface IC → interface IC → signal conditioning IC → power management / body electronics ASSP → automotive semiconductor. The MSDI provides per-input wetting current to prevent contact oxidation, programmable threshold comparators for switch-closed detection, and serial aggregation of 24 inputs into a few SPI pins — reducing wire harness complexity and MCU pin count. Key features include 35-V absolute maximum load-dump tolerance (12-V nominal), adjustable wetting current per channel, selectable ground- or supply-referenced inputs on 10 channels, integrated input debounce / de-glitch filters, configurable interrupt generation for wake events, low quiescent current sleep mode, and SPI communication up to [DATA_NEEDED: SPI clock rate]. The device operates across -40 °C to +125 °C ambient (AEC-Q100 Grade 1) and includes thermal shutdown protection. The exposed-pad HTSSOP-38 package provides theta_JA suitable for BCM thermal environments. Technically, the TIC10024-Q1 uses a per-channel comparator architecture with current-mode wetting sources driven from a shared internal regulator. The SPI peripheral implements a standard mode-0 protocol with a frame-format error flag and a global wake-up interrupt output. Internal state machine handles input filtering, hysteresis, and wetting-current modulation; channel configuration registers enable per-input current programming and pull-up/pull-down selection. Typical applications include automotive body control modules (BCM) reading 24 switches per chip, gateway/zonal controllers monitoring door/trunk/hood latches, steering-wheel switch matrices, seat-control switch aggregation, and overhead-console button clusters. The 24-input density lets a single MSDI replace multiple 8-/16-channel general-purpose I/O expanders. When designing with this part, ensure the PCB layout accommodates the exposed thermal pad with at least 4 thermal vias to the inner ground plane for AEC-Q100 thermal conformance. The 38-pin HTSSOP package requires careful routing of SPI traces; keep the SCLK/MOSI/MISO bundle length-matched and routed away from VBAT-switching nodes. This page synthesizes distributor pricing (as of 2026-10-11), drop-in same-package alternatives, and practical AEC-Q100 design notes — information not consolidated in the TI datasheet alone.

Cotação Contato

TIR1000IPWR

TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP

The Texas Instruments TIR1000IPWR is a standalone IrDA (Infrared Data Association) SIR (Serial Infrared) encoder/decoder IC housed in an 8-pin TSSOP (PW) package and rated for the -40C to +85C industrial temperature range. It encodes and decodes asynchronous UART bit streams into IrDA-compliant 3/16 pulse-modulated optical signals at data rates from 1200 bps up to 115.2 kbps, and operates from a 2.7 V to 5.5 V supply. The TIR1000IPWR is the tape-and-reel (R) packaging variant of the TIR1000IPW die, which is functionally identical to the legacy TIR1000IPWRG4. An IrDA encoder/decoder is a specialized interface IC that sits between a host microcontroller's UART and an external infrared transceiver (typically a PIN photodiode + LED pair). It performs the bit-stuffing and pulse-width modulation required by the IrDA physical layer so the host CPU only sees a transparent serial stream; the broader category belongs to interface ICs in the connectivity hierarchy (interface IC > transceiver > encoder/decoder). Key features include 1200-bps to 115.2-kbps IrDA 1.0 / HPSIR compliance, single 2.7 V to 5.5 V supply, direct UART handshake interface, low-power shutdown mode, and CMOS construction. The TIR1000IPWR adds an infrared port to any standard UART, eliminating the need for bit-banging IR protocols in firmware and offloading real-time pulse-width timing from the host MCU. The architecture uses a baud-rate generator derived from an external 16x clock (typically the UART's reference), a transmit pulse shaper that converts the UART TX bit stream into 3/16-width IR pulses, and a receive decoder that recovers the UART RX stream from the demodulated IR input. Because it is a pure logic encoder (no onboard LED driver), the host must add a discrete IR transceiver module (e.g., a TFDU4100 / HSDL-3201 class device) to drive the optical front end. Typical applications include IrDA ports on PDAs, industrial handhelds, medical data terminals, point-of-sale (POS) equipment, and consumer electronics printers. The wide supply range and 8-pin TSSOP package make it suitable for space-constrained designs that need to retrofit IrDA onto an existing UART. A key design consideration is clock sourcing. The TIR1000IPWR requires a 16x baud-rate reference clock (XCLK), which is normally derived from the host UART's baud-rate generator; if the host baud rate changes, XCLK must be reprogrammed accordingly. The IC does not include the optical transceiver, so a separate IrDA transceiver module must be added externally. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for IrDA encoder/decoder selection.

Cotação Contato

Subcategorias

Produtos (32740)

THS4304D - 3 GHz Low-Noise Wideband Op Amp | Texas Instruments

THS4522 - 95MHz Low Power Dual FDA | Texas Instruments

THS4531A - Ultra-Low-Power Fully Differential Amplifier | TI

THS4532 - Dual 0.25mA RRO Fully-Differential Amplifier | TI

THS4551IRGTR - 150MHz Fully Diff Amp | Texas Instruments

THS4551IRGTT - 150MHz Low-Noise Fully Diff Amplifier | Texas Instruments

THS6182D - Low-Power ADSL/PLC Differential Driver | TI

THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments

THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments

THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments

THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI

THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI

THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI

THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI

THVD1452DGSR - 3.3-5V RS-485 Transceiver, 50Mbps, ±18kV ESD | TI

THVD1452DR - 3.3-5V RS-485 Transceiver, ±18kV ESD, SOIC-14 | TI

THVD1510DR - 5V RS-485 Transceiver, ±18kV ESD, SOIC-8 | Texas Instruments

THVD1550 - 5V RS-485 Transceiver, 50Mbps, ±18kV IEC ESD | TI

THVD1552D - 5V RS-485 Transceiver, ±18kV IEC ESD, 50Mbps | TI

THVD1552DGS - 5V RS-485 Transceiver, ±18kV IEC ESD | TI

THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI

TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI

TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments

TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP