Circuitos Integrados

BCM5387KFBG

BCM5387KFBG - 8-Port 5GbE SGMII Switch | Broadcom

Broadcom BCM5387KFBG is an 8-port Ethernet switch with integrated SerDes, SGMII connectivity, and an SPI control interface, supplied in a 256-BGA package measuring 17 mm by 17 mm. The verified distributor information identifies the device as a 5GbE port switch, while the Broadcom product data describes its broader role as an Ethernet switch controller for multi-port network equipment. An Ethernet switch controller is an integrated circuit that coordinates traffic between multiple physical network ports. It belongs to the hierarchy of Ethernet interface integrated circuits, network interface controllers, interface semiconductors, and broader communication semiconductors. In this product, an integrated SerDes provides the physical-layer signaling path, SGMII supplies a serial Gigabit Ethernet interface, and SPI provides a host-processor control connection. The principal verified feature set includes eight switch ports, 5GbE-class operation, integrated SerDes, SGMII support, and SPI control. These features make the BCM5387KFBG relevant to compact network appliances, access equipment, industrial Ethernet systems, and other designs requiring multiple high-speed Ethernet ports. Its 256-BGA package supports dense PCB layouts, but it also requires careful escape-routing, power-plane design, and thermal analysis because of its fine ball-grid-array construction. The integrated SerDes architecture reduces the need for separate PHY-related circuitry when the host system uses compatible SGMII links. SGMII carries Ethernet data and control information over a high-speed parallel or serial interface intended for communication between Ethernet switching or PHY subsystems and a host processor. Exact lane rates, SerDes signaling levels, supported copper media, and internal switching architecture were not exposed in the supplied verified results and must be confirmed in the manufacturer datasheet before design release. Typical implementation targets include eight-port Ethernet switches, industrial network gateways, endpoint controllers, and communication equipment that uses SGMII-connected SerDes links. The SPI interface can support register configuration, initialization, and runtime control from an embedded controller. Actual protocol timing, register access behavior, clock requirements, and software model should be validated against Broadcom's complete technical documentation rather than inferred from distributor summaries. A critical design consideration is the 256-BGA footprint. Signal escape routing, via-in-pad use, multilayer construction, power-plane continuity, and exposed thermal strategies can materially affect manufacturability. The supplied sources do not provide detailed pin assignments, ball maps, recommended capacitors, or thermal resistance, so these values remain unavailable and should be obtained from the authoritative Broadcom documentation before schematic capture. This page consolidates verified distributor availability, the published 12.6817 US-dollar starting price as of 2026-10-29, package identification, interface descriptions, and a rigorous drop-in-replacement assessment. It also separates documented facts from missing engineering data, helping procurement and engineering teams avoid assuming unverified pin compatibility or unconfirmed electrical performance.

Cotação Contato

BCM5388KPBG

BCM5388KPBG - 8-Port Unmanaged Gigabit Ethernet Switch | Broadcom

Broadcom BCM5388KPBG is an 8-port unmanaged Gigabit Ethernet switch controller in the Interface ICs category. The verified product description identifies the device as an 8-port unmanaged GE switch, while distributor listings classify it as an interface controller. These details position the part as a network connectivity solution for designs that require multiple Gigabit Ethernet ports without managed-switch features. An unmanaged Ethernet switch provides basic layer-2 frame forwarding between connected devices while automatically learning source MAC addresses. This operating model reduces configuration complexity and can shorten evaluation time in embedded gateways, industrial controllers, digital signage systems, access equipment, and other networked products. The BCM5388KPBG is specifically identified as supporting eight Gigabit Ethernet ports, making it relevant to compact systems that need to consolidate several network links into one switching device. The verified data does not specify PHY integration, supported copper media, upper-layer interfaces, switching fabric throughput, frame-buffer capacity, MAC-address capacity, auto-negotiation behavior, VLAN support, operating temperature, supply voltage, or package dimensions. Those parameters must be confirmed in the manufacturer documentation before the device is specified for a new design. In particular, engineers should verify whether an external magnetics interface is required and whether the host processor connects through an embedded controller interface, a parallel bus, or another serial interface. The KPBG ordering suffix identifies a specific Broadcom orderable configuration, but the supplied snippets do not establish its exact package, pin count, lead-free status, or automotive qualification. Consequently, a board-level footprint cannot be treated as confirmed from the available evidence. Before replacing an existing BCM5388KPBG, compare the complete ordering code, exposed pad requirements, pin names, reference clock, power rails, reset behavior, strap options, and external component recommendations against the applicable datasheet revision. BCM5388KPBG is best considered for unmanaged Gigabit Ethernet aggregation rather than applications requiring VLAN policy, spanning-tree management, packet prioritization, or administrative control. It can simplify a network architecture when eight local links must reach one internal host or uplink. Its suitability depends on matching the verified port count and interface requirements to the target system while confirming all electrical and mechanical details that are absent from the current source excerpts. This page distinguishes verified product facts from unavailable technical fields and explicitly identifies missing data rather than guessing. It also consolidates source links, sourcing guidance, application-fit considerations, and drop-in-replacement constraints. That separation is important because an 8-port unmanaged switch function alone does not prove package, pin, software, or electrical compatibility with another Ethernet switch.

Cotação Contato

BCM5389IFB

BCM5389IFB - 8-Port SGMII Ethernet Switch | Broadcom

Broadcom BCM5389IFB is an 8-port SGMII Ethernet interface controller integrating a packet buffer, media access controllers, address management, and a non-blocking switch controller in one monolithic 0.13 µm CMOS device. It complies with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3x, supporting the MAC control, pause-frame, and auto-negotiation functions required by industry-standard Ethernet, Fast Ethernet, and Gigabit Ethernet equipment. The device is supplied in a 256-ball BGA package for high-density telecommunications and networking designs. An Ethernet switch controller is a specialized network-interface IC that coordinates traffic among multiple Ethernet ports. In the broader hierarchy, it belongs to Ethernet controllers, then network interface controllers, then interface ICs, and ultimately semiconductor components. Broadcom's BCM5389 family consolidates switching, buffering, media access control, and management functions so that a system can implement a multiport switching subsystem without assembling the equivalent from separate discrete blocks. The verified product information identifies BCM5389IFB as an 8-port SGMII switch interface and an Ethernet controller. Its integration reduces the number of external functional blocks and can simplify board routing compared with a multi-chip architecture. The non-blocking switch controller is designed to process traffic among the eight ports while the packet buffer manages queued frames. SGMII provides the physical-layer interface between the MAC-side controller and external Ethernet PHYs. Compliance with IEEE 802.3 and its 802.3u, 802.3ab, and 802.3x subsections provides compatibility with standard Ethernet, Fast Ethernet, and Gigabit Ethernet devices. The included MAC control and pause-frame support are relevant to traffic management, while auto-negotiation support helps the system establish compatible operating modes with connected network equipment. These functions make the controller suitable for gateways, access equipment, and other multiport network systems. Typical implementation places BCM5389IFB between eight SGMII-capable external PHYs and the surrounding switching or communications system. The controller manages the Ethernet MAC and switching functions, while the PHYs perform signal transmission and reception. Board design must account for high-speed differential routing, solid return paths, decoupling, BGA assembly, and the thermal footprint of a 256-ball package. For an existing PCB, replacement should not be selected from the generic BCM57xx, BCM53xx, or BCM54xx families without verifying the exact pinout, power rails, clocking, PHY interface, management registers, and protocol support. The verified data does not identify any pin-compatible substitute, so this page does not assert an unverified drop-in replacement. This page combines the verified manufacturer-document excerpts with practical integration guidance, comparison context, and procurement information. It distinguishes documented functionality from parameters that remain unavailable, helping engineers evaluate BCM5389IFB without treating generic Ethernet-controller family similarities as proof of replacement compatibility.

Cotação Contato

BCM5389IFBG

BCM5389IFBG - 8-Port Gigabit Ethernet Switch | Broadcom

The Broadcom BCM5389IFBG is an 8-port Gigabit Ethernet switch with integrated SerDes in a 256-pin FBGA package. It combines eight 1000 Mb/s SGMII/SerDes ports, one GMII/RGMII/RvMII interface, nine IEEE 802.x-compliant MACs, a 128 KB packet buffer, and support for 9 KB jumbo frames. Its 1.2 V operating supply makes it suitable for compact, power-conscious SOHO and subnet networking equipment. An Ethernet switch is a semiconductor that forwards Ethernet frames between connected ports using dedicated MAC addresses. The BCM5389IFBG belongs to the Ethernet switch hierarchy, where it integrates multiple physical-layer-facing SerDes interfaces with frame-processing logic. This consolidation allows a router, gateway, or subnet switch to support multiple Gigabit Ethernet links without requiring eight separate external switch devices. Its integrated SerDes also reduces board-level interconnect requirements compared with solutions using discrete PHY components. Key features include eight Gigabit Ethernet ports, eight SGMII/SerDes interfaces, one selectable GMII, RGMII, or RvMII interface, and nine compliant MACs. The device supports 128 KB of packet buffering and 9 KB jumbo frames. According to the Broadcom datasheet indexed by the verified sources, it complies with IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3x, including MAC control, pause-frame, and autonegotiation behavior. These standards provide the foundation for Fast Ethernet, Gigabit Ethernet, flow control, and compatible network interoperability. The eighth-generation switch-on-chip architecture is intended to reduce the external component count of multiport network products. Eight integrated SerDes interfaces can expose copper or optical network links through suitable PHY or transceiver circuitry, while the GMII/RGMII/RvMII interface connects the switching system to a host processor or uplink controller. The 256-pin FBGA package supports high-density routing but requires careful escape-routing and via-in-pad or fanout-aware PCB construction. Typical applications include SOHO routers, residential gateways, Ethernet subnet switches, network appliances, and industrial or embedded systems that aggregate multiple Gigabit Ethernet links. The 1.2 V supply and integrated SerDes can simplify power-tree design and reduce PCB area, but the high-density BGA package, multi-rail sequencing requirements, and high-speed signal integrity demands careful reference-plane continuity, decoupling, and connector-return-path planning. The principal design challenge is preserving signal integrity across the short, dense escape paths between the FBGA device and external PHY, magnetics, and connector hardware. Differential SerDes routing should use a continuous reference plane, controlled impedance, minimal stubs, and tightly placed decoupling. Differential pair geometry, via transitions, and return paths must be validated with the actual PCB stack-up and connector models. This page consolidates verified Broadcom and distributor information into an application-oriented engineering summary, including the switch architecture, interface hierarchy, package implications, design cautions, and the one same-family drop-in candidate supported by the supplied cross-reference evidence. Pricing and lead time remain distributor-dependent and should be confirmed for the requested quantity as of the current sourcing date.

Cotação Contato

BCM5389KFB

BCM5389KFB - 8-Port Gigabit Ethernet Switch | Broadcom

Broadcom BCM5389KFB is an 8-port Gigabit Ethernet switch with integrated SerDes, a 9-Gigabit non-blocking switch fabric, and a 256-BGA package measuring 17 x 17 mm. The verified source data identifies one GMII/RGMII/RvMII interface, nine 802.x-compliant MACs with 9-KB jumbo-frame support, eight SGMII/SerDes interfaces, 128-KB packet-buffer memory, and an SPI control interface. An Ethernet switch is a semiconductor that connects multiple network endpoints through a shared internal fabric, forwarding Ethernet frames according to learned or configured addresses. The BCM5389 belongs to the switch-controller and Ethernet-interface hierarchy, integrating access-port connectivity, integrated SerDes, MAC processing, packet buffering, and host configuration into one highly integrated network controller. The headline feature set is tailored to multiport Ethernet equipment: eight SGMII/SerDes ports, a 9-Gigabit aggregate non-blocking fabric, 128 KB of packet-buffer memory, and nine compliant MACs. The SPI interface provides configuration and control access, while GMII/RGMII/RvMII support broadens host-side and uplink connectivity. A maximum 9-KB frame size accommodates jumbo traffic and avoids unnecessary fragmentation on supported links. The 256-BGA package concentrates substantial networking functionality into a compact 17 x 17 mm surface-mount footprint. Its many balls support high-density interconnect requirements but also demand careful PCB escape routing, via geometry, ground distribution, and assembly-process control. Exact electrical limits, clocking requirements, SerDes rates, voltage rails, and environmental ratings were not supplied in the verified data and must be confirmed in the manufacturer documentation before design release. Typical uses include Gigabit Ethernet switches, industrial Ethernet equipment, access-network appliances, embedded network gateways, and aggregation equipment that needs multiple copper or PHY-facing ports. The integrated SerDes makes the device relevant to designs where compactness, deterministic fabric throughput, and centralized packet handling are more important than a simple standalone PHY. Designers should treat the complete BCM5389 reference design, including power planes, decoupling, clocking, SerDes channel routing, reset sequencing, and PHY integration, as the starting point. SPI firmware must configure ports, packet handling, MAC behavior, and management settings consistently. Do not infer pin compatibility, power rails, timing, or automotive qualification from the package name alone. This page consolidates the verified distributor description, Octopart sourcing information, architecture features, procurement context, and practical integration cautions. It distinguishes documented BCM5389 capabilities from parameters that still require manufacturer confirmation, helping engineers identify the device efficiently without presenting unverified specifications as facts.

Cotação Contato

BCM5389KFBG

BCM5389KFBG - 8-Port Gigabit Ethernet Switch | Broadcom

Broadcom BCM5389KFBG is an 8-port Gigabit Ethernet switch with integrated SerDes, an SPI controller interface, and a 256-BGA package measuring 17 x 17 mm. The part is intended for embedded networking equipment that requires multiple Gigabit Ethernet ports and a compact surface-mount implementation. Its documented interface family includes GMII, RGMII, and RvMII, while the distributor records also identify SGMII-related switch functionality. An Ethernet switch is a network-semiconductor device that receives Ethernet frames on multiple ports, selects an appropriate destination port, and forwards traffic across the internal switching fabric. The BCM5389 belongs to the broader hierarchy of Ethernet controllers, interface controllers, network semiconductors, and communication ICs. Integrating eight Gigabit Ethernet ports with SerDes capability can reduce the component count required in gateways, access equipment, and embedded switching platforms. The principal verified characteristics are the eight-port architecture, integrated SerDes, SPI interface, and 256-BGA (17 x 17 mm) package. The component is categorized by DigiKey as an Ethernet Switch with an SPI Interface, while Mouser describes it as an eight-port SGMII switch. These records establish the device's core positioning, but the supplied source snippets do not expose detailed electrical ratings for operating voltage, clock frequency, serializer lane rate, memory interfaces, or physical dimensions beyond the package size. The 256-BGA package is a high-pin-count surface-mount format intended for multilayer printed circuit boards. A successful implementation depends on exact land-pattern, ball-map, power-rail, clocking, SerDes routing, and thermal design information in the manufacturer documentation. Because the available source material provides only a short datasheet description and distributor summaries rather than the complete manufacturer PDF, no unverified switching capacity, latency, PHY count, SerDes standard, or pin-level functions are inferred here. Typical application spaces include carrier-grade and access-network switching, industrial Ethernet gateways, embedded routers, set-top and customer-premises equipment, and other multi-port networking systems. The eight Gigabit Ethernet ports suit centralized connectivity, while integrated SerDes can support backplane or interconnect links when the particular port configuration and supported electrical interface match the system architecture. Designers should verify the exact Broadcom reference design, supported boot and host interface requirements, pin assignments, reference voltage, and power-delivery network before layout release. The BGA package also requires careful escape routing, via arrays, plane splitting, and thermal-via placement. Any substitute must be checked against the complete ball map and electrical tables rather than selected from package dimensions alone. This page consolidates verified distributor pricing and inventory, candidate same-family comparisons, technical gaps, and practical implementation cautions. It adds sourcing context and replacement screening beyond the brief distributor snippets while clearly separating verified facts from parameters that still require confirmation from the complete Broadcom datasheet.

Cotação Contato

BCM5395MIPBG

BCM5395MIPBG - 5-Port Ethernet Switch | Broadcom

Broadcom BCM5395MIPBG is a five-port Gigabit Ethernet switch with five integrated physical-layer devices, GMII, RGMII, MII, and RvMII interfaces, non-volatile configuration storage, and interrupt generation in an FBGA package. It consolidates multi-port Ethernet connectivity into a single networking IC and is intended for systems that need local switching without implementing separate physical-layer devices for every port. An Ethernet switch is a semiconductor that receives Ethernet frames on one interface, examines their destination address, and forwards traffic to the appropriate output port. This device sits between the physical layer and the system network architecture: its integrated PHYs connect copper links, while GMII, RGMII, MII, and RvMII provide links to a host processor or another Ethernet controller. Its five-port architecture is suited to gateways, embedded network appliances, industrial controllers, and access equipment with several local Ethernet connections. The defining feature of the BCM5395MIPBG is the integration of five Ethernet PHYs with a five-port switching function. Supported interfaces include GMII, RGMII, MII, and RvMII, allowing the implementation to accommodate different host-clocking and signal-rate requirements. Non-volatile configuration storage retains device settings across power cycles, while interrupt generation allows the host processor to receive event notifications without continuous status polling. The BCM5395 family integrates physical-layer functions, packet buffering, and switching resources within one device. This integration can reduce the number of discrete network components required in an embedded Ethernet design and centralize port management. Because the exact clocking limits, electrical characteristics, operating temperature range, and power ratings depend on the complete manufacturer documentation, engineers should validate those details against the applicable Broadcom datasheet and reference design before releasing production hardware. Typical applications include industrial Ethernet gateways, embedded network appliances, access-point equipment, set-top platforms, and communication controllers requiring several local Gigabit Ethernet links. The integrated PHYs are especially useful where PCB area is constrained and the system requires multiple copper ports connected to a single host interface. RGMII can reduce host pin count in appropriate designs, while MII and GMII support legacy or lower-speed parallel-interface implementations. A successful design must preserve the exact pin assignments, reference clocks, supply sequencing, magnetics isolation, impedance-controlled differential pairs, and decoupling requirements specified for BCM5395MIPBG. Do not substitute a generic Ethernet PHY solely by port count; verify the package ball map, register behavior, interrupt configuration, non-volatile settings, and supported host interface before considering any replacement. This product page organizes the BCM5395MIPBG’s interface capabilities, application guidance, design checks, and verified sourcing information into a compact engineering reference. It also distinguishes documented functions from parameters that require confirmation from the manufacturer’s complete package and electrical documentation.

Cotação Contato

BCM5395MKFBG

BCM5395MKFBG 5-Port Gigabit Ethernet Switch | Broadcom

Broadcom BCM5395MKFBG is a five-port Gigabit Ethernet switch with five integrated PHYs and integrated packet buffer. The device operates at 10 Mbps, 100 Mbps, and 1 Gbps Ethernet rates and is identified as a CMOS Ethernet interface IC. It is intended for embedded networking equipment requiring multiple copper Ethernet ports, local switching, and integrated MAC and PHY functions in one device. An Ethernet switch is a network-interface semiconductor that connects multiple Ethernet ports and forwards frames according to MAC addresses. A Gigabit Ethernet switch with integrated PHYs combines the physical-layer transceiver functions with switching and packet-buffer logic. This integration reduces the number of separate network components required in a compact design and provides a common interface for 10 Mbps, 100 Mbps, and 1 Gbps Ethernet connections. The BCM5395 family provides five integrated Gigabit PHYs and packet-buffer capacity within one Broadcom device. The listing identifies the part as a five-port switch and describes support for MII, RGMII, GMII, and RvMII operating interfaces. These interface choices support connection to a host processor, embedded controller, or another Ethernet block when the selected board configuration and electrical design meet the device requirements. The BCM5395 implementation uses CMOS technology and is categorized as an Ethernet interface and switching IC. Its five integrated PHYs are intended to reduce system complexity compared with a design using discrete Ethernet transceivers. The device is also associated with IEEE 802.3az Energy Efficient Ethernet support, making it relevant to network equipment that emphasizes power efficiency while retaining multiple Gigabit Ethernet ports. Typical applications include industrial Ethernet gateways, home-automation controllers, set-top and media devices, access-point equipment, embedded network appliances, and industrial control systems. For these applications, the five integrated PHYs can support multi-port copper networking while preserving a compact board layout. The available device information does not define the exact pin assignments, package dimensions, or detailed electrical limits. When designing around BCM5395MKFBG, verify the exact package land pattern, power rails, clock requirements, PHY characteristics, and interface voltage levels against the Broadcom datasheet before layout. Keep high-speed traces short, provide the recommended power and decoupling network, and follow the reference design for magnetics or PHY copper connectivity. This device should be selected only after checking that all five ports, supported media interfaces, and environmental requirements match the target system. This product page organizes the confirmed BCM5395MKFBG specifications, sourcing references, application context, and engineering trade-offs. It also separates explicitly documented facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers evaluate the switch without relying on incomplete distributor summaries.

Cotação Contato

BCM5395SIPB

BCM5395SIPB - 5-Port Gigabit Ethernet Switch | Broadcom

The Broadcom BCM5395SIPB is an integrated Ethernet switching IC associated with a five-port Gigabit Ethernet switch, combining five integrated physical-layer devices with an internal packet buffer in a single device. Distributor listings classify the SIPB ordering code under interface drivers, receivers, and transceivers, while the underlying BCM5395 device is described as a 5-port Gigabit Ethernet switch with five integrated PHYs and a packet buffer. Its exact package dimensions, pin count, electrical limits, and thermal ratings are not present in the supplied verified sources. An Ethernet switch is a semiconductor in the network-interface hierarchy: it connects multiple Ethernet ports, examines frame destinations, and forwards traffic only to the required output ports. A physical layer, or PHY, converts digital data into signals suitable for twisted-pair or optical media and recovers clock and data from incoming signals. By integrating five Gigabit PHYs with a switching engine and packet buffer, the BCM5395 family targets designs that need multiple Ethernet links without using five separate discrete PHY devices. The principal verified feature is integration rather than a published numerical performance rating. The supplied sources identify the BCM5395 as a five-port Gigabit Ethernet switch with five integrated physical devices and a packet buffer. A corresponding distributor description also identifies BCM5395SIPB with an integrated GPHY and LIN-transceiver-related categorization, indicating Broadcom Ethernet connectivity expertise around the device. Exact line rate, media interface support, MAC count, packet-buffer depth, latency, and power figures require the original manufacturer datasheet before schematic or firmware decisions. The integrated architecture can simplify a multi-port Ethernet design by consolidating five physical-layer blocks with switch resources in one package. Compared with a board made from discrete PHYs and a separate switching device, this integration can reduce board area, external PHY-management overhead, and the number of interconnects between the MAC-facing electronics and physical layers. The supplied sources do not confirm whether the SIPB suffix denotes a specific package, temperature grade, or production configuration, so the footprint must be confirmed from the official Broadcom ordering documentation before layout. Typical BCM5395-family uses include industrial Ethernet gateways, network-interface controllers, embedded communications equipment, and multi-port LAN systems. Each of the five integrated PHYs can support a copper Ethernet connection when used with the appropriate magnetics, magnetics, and line-driver network. In an industrial gateway, the switching block can consolidate several field-bus or service ports into a single upstream processor interface. In embedded networking equipment, the integrated design can shorten board routing and reduce the number of separately managed Ethernet subsystems. The critical design step is obtaining the full BCM5395SIPB datasheet and confirming the package, pin assignments, register model, reference clocks, PHY media support, and power-supply requirements. Do not assign PCB pads from distributor snippets alone. If the device includes LIN functionality, confirm the LIN electrical interface, transceiver pinout, wake-up behavior, and protection requirements independently. Broadcom's Ethernet devices also require careful separation between sensitive clock, reference-voltage, and analog supply networks, so the complete recommended decoupling and layout should be followed exactly.

Cotação Contato

BCM5395SIPBG

BCM5395SIPBG - 5-Port Gigabit Ethernet Switch | Broadcom

Broadcom BCM5395SIPBG is a five-port Gigabit Ethernet switch with five integrated physical-layer devices and an integrated packet buffer in a surface-mount package. Each of its five switch ports supports operation at 1000 Mbps, while the integrated PHYs reduce the number of separate Ethernet transceiver components required in a network interface design. The packet buffer provides on-chip frame handling between the integrated ports and the host-facing interface. An Ethernet switch is a networking semiconductor that connects multiple Ethernet endpoints through a shared switching fabric. A five-port Gigabit Ethernet switch belongs to the interface IC and Ethernet switch hierarchy: it combines digital frame-processing logic, integrated packet buffering, and physical-layer transceiver functions. The integrated-PHY architecture simplifies board design compared with a discrete switch-and-PHY arrangement, although the complete system still requires suitable magnetic components, routing, power delivery, and signal-integrity implementation. The principal features of the BCM5395SIPBG are its five Gigabit Ethernet ports, five integrated PHYs, and integrated packet buffer. These functions support compact local-area-network designs for business, industrial, and embedded equipment. The five-port configuration can connect four external network devices while retaining one port for an uplink to a larger network, provided the host interface and firmware support the intended topology. Its 1000 Mbps-per-port capability supports Gigabit Ethernet links where higher bandwidth is required. The BCM5395 family integrates substantial network-interface functionality into one device. Five integrated PHYs eliminate five separate external PHY packages when each port requires 1000BASE-T connectivity. The integrated packet buffer supports local frame storage and switching operations, reducing reliance on external memory around the switching core. The device is positioned as an interface and transceiver-class network IC rather than a general-purpose processor, so its surrounding circuitry must provide the appropriate host-facing interface, clocking, power, and physical-layer network connections. Typical implementation areas include small office network switches, industrial Ethernet equipment, embedded gateways, printer and storage networking, and compact multiport Ethernet interfaces. A five-port arrangement can also serve as the central switching element in a small embedded network. These uses depend on confirming host-interface requirements, supported PHY media, electrical characteristics, package details, and operating conditions against the Broadcom BCM5395 datasheet before schematic capture. PCB implementation requires careful separation between the digital host interface and sensitive analog PHY networks. Magnetic-interface components, termination, controlled-impedance routing, ground-plane continuity, and adequate decoupling should follow the manufacturer reference layout and component guidance. Confirm the exposed-pad, thermal, and decoupling requirements from the package documentation, because those details determine the number of input and output pins and the exact footprint that must be used in the PCB library. This page consolidates the identified switching features, sourcing guidance, application context, and design considerations into a concise engineering reference. It also distinguishes confirmed BCM5395 capabilities from package, electrical, lifecycle, and pin-level details that must be confirmed from the manufacturer documentation before layout release or production qualification.

Cotação Contato

BCM5396IFB

BCM5396IFB - 16-Port Gigabit Switch | Broadcom

Broadcom BCM5396IFB is a 16-port Gigabit Ethernet switch with integrated SerDes, delivering a 17-Gigabit non-blocking switching fabric in a BGA package. It includes seventeen IEEE 802.3-compliant MACs, sixteen SGMII/SerDes interfaces, a 256-KB packet buffer, and one GMII/RGMII/RvMII uplink. An Ethernet switch is a semiconductor that receives Ethernet frames on multiple ports, stores them briefly, examines addressing information, and forwards each frame only toward its destination port. The BCM5396 combines physical-layer SerDes interfaces, Media Access Controllers, address management, packet buffering, and switching control within one monolithic 0.13 µm CMOS device. This integration reduces the component count required for multiport Gigabit networking equipment. The verified BCM5396 data identifies sixteen SGMII/SerDes ports, seventeen compliant MACs, one GMII/RGMII/RvMII interface, and a non-blocking 17-Gigabit Ethernet switch fabric. It supports jumbo frames up to 9 KB and includes a 256-KB packet buffer. The Broadcom datasheet also states compliance with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3x, including MAC-control PAUSE handling. Technical implementation centers on the integrated SerDes interfaces and the internal switching architecture. Sixteen Gigabit Ethernet links terminate through SGMII/SerDes, while a separate parallel interface supports an uplink or management-facing port. The switch fabric is designed to forward traffic without a blocking bottleneck across the aggregate 17-Gigabit capacity, and packet buffering absorbs short traffic bursts before forwarding decisions are completed. Typical applications include 16-port Gigabit Ethernet switches, industrial network equipment, network-interface appliances, aggregation equipment, and embedded systems requiring multiple copper or fiber-linked Ethernet ports. The parallel uplink can connect the switched ports to a host processor, another switch, or a router, depending on the surrounding system architecture. PCB design must follow the manufacturer’s BGA land pattern, ball assignment, power, clock, SerDes, and decoupling requirements. Differential high-speed pairs need controlled impedance, uninterrupted reference planes, minimized stubs, and manufacturer-recommended spacing. Because the supplied excerpts do not include operating voltage, temperature range, pin list, or exact package dimensions, those values should be confirmed from the full manufacturer datasheet before release. This product record combines verified source links, procurement fields, interface facts, and design-focused context. The alternatives list remains intentionally limited because the supplied cross-reference search did not identify any verified pin-compatible replacement MPNs.

Cotação Contato

BCM5396IFBG

BCM5396IFBG - 16-Port Gigabit Layer 2 Switch | Broadcom

Broadcom BCM5396IFBG is a highly integrated 16-port Gigabit Ethernet Layer 2 switch with integrated SerDes in a monolithic 0.13 μm CMOS device. The verified manufacturer documentation describes a complete high-speed switch system combining a packet buffer, Media Access Controllers, address management, and a non-blocking switch controller. It supports the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3x specifications, including MAC control PAUSE-frame handling, making it suitable for structured networking equipment, gateway platforms, routers, switches, and industrial Ethernet systems. The part is identified by distributors as a 16-port Layer 2 Gigabit Ethernet switch with integrated SerDes, and one distributor lists the BCM5396IFBG from $45.6230 as of 2026-10-28. The BCM5396IFBG is a Broadcom Limited interface IC with an exact package designation and pinout not included in the supplied verified data. Consequently, package dimensions, pin names, electrical limits, clocking requirements, thermal ratings, and absolute maximum ratings are recorded as unavailable rather than estimated. Its integrated SerDes architecture can reduce external switching-component count in a Layer 2 design, while the non-blocking controller and packet buffer support high-throughput Ethernet aggregation. The IEEE 802.3x PAUSE-frame support is important when downstream devices cannot accept traffic at line rate, although exact buffering and flow-control thresholds must be confirmed from the manufacturer datasheet. This product page is intended as an engineering summary, not as a substitute for the complete Broadcom data sheet. It combines verified source information, commercial availability, application context, and strict data-quality markers to distinguish documented facts from values that still require confirmation before schematic capture, PCB layout, thermal analysis, or production release. The BCM5396IFBG should therefore be evaluated as a highly integrated switching solution for Gigabit Ethernet products where port density, integrated SerDes, Layer 2 management, and non-blocking switching are the primary design requirements.

Cotação Contato

BCM5396KFB

BCM5396KFB - 16-Port Gigabit Switch IC | Broadcom

The Broadcom BCM5396KFB is a 16-port Gigabit Ethernet switch integrated circuit with integrated SerDes, specified in a 256-pin FBGA package and a 16,000 Mbps switching capacity. It combines the packet buffer, Media Access Controllers, address management, and a non-blocking switch controller in one monolithic 0.13 µm CMOS device, providing a compact foundation for multiport Ethernet systems. A Gigabit Ethernet switch is a network-semiconductor device that receives Ethernet frames through multiple ports, maintains the required MAC and address information, and forwards traffic through an internal switching fabric. Ethernet switching belongs to networking and communications electronics, where throughput, port density, media interfaces, buffering, and frame handling determine whether a system can support simultaneous data flows without unnecessary contention. The BCM5396KFB's principal verified features include 16 Gigabit Ethernet ports, integrated SerDes, and a non-blocking switch controller. Its listed aggregate throughput is 16,000 Mbps. The Broadcom datasheet also states compliance with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3x, including MAC-control PAUSE-frame support. These functions place the device in the family of Ethernet interface and switching semiconductors rather than a general-purpose microcontroller or standalone physical-layer transceiver. The monolithic 0.13 µm CMOS implementation consolidates packet buffering, MACs, address management, and switching control. That integration can reduce the number of external network components in a designed platform, although board-level operation still depends on power delivery, clocking, SerDes implementation, thermal conditions, magnetics or PHY integration, and validated firmware or driver support. The supplied distributor references classify the part as a 16-port layer-2 Gigabit switch with integrated SerDes. Typical equipment uses include 16-port managed Gigabit Ethernet switches, industrial Ethernet aggregation, network-interface appliances, telecom access equipment, and embedded systems that need multiple copper or fiber-facing ports. These uses are consistent with the verified 16-port architecture; exact supported media type, connector arrangement, electrical limits, and board implementation must be confirmed from the complete manufacturer datasheet before release. Engineers should preserve the manufacturer's ball map, power and decoupling layout, thermal design, and high-speed routing constraints. A 256-pin FBGA is demanding to route and inspect, so assembly yield, via-in-pad policy, solder-mask definition, and X-ray or AOI coverage should be reviewed early. This page separates verified facts from unavailable electrical details and avoids treating distributor classifications as substitutes for a complete pinout. This page consolidates distributor sourcing, datasheet references, design cautions, and strict drop-in-compatibility checks that are not available from a bare distributor listing. Because no verified substitute shares the exact BCM5396 footprint and electrical configuration, engineering review is required before any proposed replacement is approved.

Cotação Contato

BCM5396KFBG

BCM5396KFBG - 16-Port Gigabit Ethernet Switch with Integrated SerDes | Broadcom

The Broadcom BCM5396KFBG is a 16-port Gigabit Ethernet switch with integrated SerDes, provided in a 256-FBGA package measuring 17 x 17 mm. It combines packet buffering, Media Access Controllers, address management, and a non-blocking switch controller in one monolithic 0.13 µm CMOS device. The device uses an SPI interface for host configuration and supports the IEEE 802.3, 802.3u, 802.3ab, and 802.3x specifications identified in the manufacturer datasheet. An Ethernet switch is a network-semiconductor device that receives Ethernet frames on multiple ports and forwards them through a shared internal switching fabric. The BCM5396 family integrates 16 Gigabit Ethernet ports with physical-layer transceiver functions, allowing a board to implement a multi-port network interface without using a separate switch controller and sixteen external SerDes devices. The switch controller and packet-buffer architecture coordinate traffic transfer among ports. The most prominent functional characteristics are the 16 Gigabit Ethernet ports, integrated SerDes, non-blocking switch operation, and integrated packet buffer. The monolithic design also includes Media Access Controllers and address management. These features make the BCM5396 suited to compact networking equipment where port density, integration, and board area matter. The SPI host interface provides a control path for configuring switch operation and managing relevant networking parameters. Broadcom's manufacturer datasheet describes the BCM5396 as a highly integrated high-speed switch solution. It is implemented in 0.13 µm CMOS, combining the MACs, packet buffer, address-management logic, and switch controller rather than relying on discrete components for those functions. It complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3x specifications, including support for MAC-control PAUSE frames. Exact clock, voltage, power, and temperature limits were not available in the supplied excerpts and require confirmation in the complete datasheet. Typical applications include industrial Ethernet switches, telecom access equipment, network-interface appliances, and multi-port embedded networking systems. In these systems, the 16 integrated ports can reduce component count and PCB routing demand compared with a design built from discrete Ethernet PHYs. Its low-power operating mode, noted in distributor product information, may be useful when port activity or traffic demand is limited. The SPI interface also makes the device suitable for systems whose supervising processor must initialize or supervise the switch. The primary design consideration is package complexity. A 256-FBGA device requires a fine-pitch PCB land pattern, careful escape routing, reliable power and ground distribution, and assembly capability suitable for large ball-grid arrays. Designers should also verify clock requirements, SerDes electrical characteristics, thermal performance, reset behavior, and supported PHY or media arrangements against the complete manufacturer datasheet before releasing layout or production files. This page consolidates verified distributor listings, the Broadcom manufacturer datasheet excerpt, package information, sourcing data, and application guidance. It also distinguishes documented BCM5396 capabilities from details that still require validation, helping engineers evaluate the device without mistaking incomplete distributor metadata for a complete electrical specification set.

Cotação Contato

BCM5482A1KFB

BCM5482A1KFB Dual-Port Gigabit Ethernet PHY | Broadcom

The Broadcom BCM5482A1KFB is a dual-port 10/100/1000BASE-T Ethernet physical-layer transceiver with integrated SerDes, supporting 10, 100, and 1000 Mb/s operation in half-duplex and full-duplex modes. The device is supplied in a 121-pin plastic ball grid array package for compact network-interface designs. An Ethernet PHY converts between a digital MAC-side interface and analog copper-cable signaling. The BCM5482A1KFB integrates two physical-layer channels, allowing one component to serve two Ethernet ports while reducing board area in IP phones, access equipment, industrial controllers, and other multiport systems. Its dual-port architecture can reduce the number of discrete PHY packages required on a board. The BCM5482A1KFB supports 10, 100, and 1000 Mb/s rates and is compatible with IEEE devices operating in half-duplex and full-duplex configurations. This broad rate support lets a product design accommodate legacy 10BASE-T and 100BASE-TX links while retaining Gigabit Ethernet capability. The integrated SerDes also connects the PHY channels to digital network processors or switching silicon. Clock timing can be adjusted to compensate for board-trace delays required by the RGMII specification. This feature is particularly useful when the PHY and MAC are separated by a routed interface or when propagation delay through a multilayer board would otherwise affect timing margins. The adjustment capability supports more practical placement of high-speed digital circuitry on space-constrained boards. Low-power operation is a central design benefit for dual-port PHYs because each active channel continuously performs line coding, signal conditioning, and cable diagnostics. The device is suited to IP phone uplinks, industrial networking equipment, customer-premises equipment, and embedded dual-Ethernet systems where package size, port density, and interface timing are important design constraints. For implementation, follow the Broadcom BCM5482 documentation for power sequencing, magnetic-component selection, termination, clock configuration, and the exact pin assignments. Preserve the recommended high-speed layout practices around the RGMII interface and place input, output, and decoupling connections according to the reference design to avoid signal-integrity degradation. This page combines the device’s dual-port Gigabit Ethernet capabilities with practical selection guidance, verified source links, interface considerations, and design guidance. It is designed to help engineers identify the correct operating conditions and board-level integration requirements before committing a BCM5482A1KFB-based Ethernet interface to production.

Cotação Contato

BCM55030SB01

BCM55030SB01 - 10G EPON MDU Clock/Timing IC | Broadcom

The Broadcom Limited BCM55030SB01 is an application-specific clock and timing integrated circuit identified by distributor listings as a 10G EPON MDU device. It belongs to the Clock & Timing category within integrated circuits and is supplied in a surface-mount package designated by the SB01 ordering suffix. The verified source data identifies the component as an IC output device, but it does not publish the operating voltage, output frequency, timing tolerance, temperature range, or pin configuration needed for a complete electrical specification. An application-specific clock and timing IC is a specialized semiconductor that generates, distributes, or conditions clock signals within a defined equipment architecture. Unlike a generic oscillator, an application-specific timing device is optimized around a particular system or transceiver ecosystem. In an EPON MDU, clock and timing support can be required alongside burst-mode transmitters, receivers, serializers, and other line-access circuitry, where consistent clocking contributes to stable data throughput and low bit-error rates. The key verified identification for BCM55030SB01 is its association with a 10G EPON MDU application. That association is more useful than a generic category label because it indicates the intended equipment context in which Broadcom positioned the part. Distributor records classify it under Application Specific Clock/Timing, while other marketplace listings describe it as an IC Output and an application-specific timer. The Broadcom family also includes closely related BCM55030-series devices, but the supplied evidence does not establish their pin compatibility or parameter differences with this exact suffix. Because no manufacturer datasheet parameters or verified pricing were returned in the source data, electrical values such as supply voltage, output frequency range, jitter, reference-input requirements, and operating temperature must be confirmed before design release. Likewise, the physical package dimensions and pad assignment remain unverified. The package diagram is therefore represented by the default library graphic rather than an invented package-specific drawing, and the pinout is intentionally omitted instead of presenting unverified pin names. Typical engineering use is limited to designs already qualified around the Broadcom 10G EPON MDU signal chain, including line-card, aggregation, and access-network equipment. For new designs, engineers should request the controlled Broadcom datasheet and obtain a sample of BCM55030SB01 to confirm reference requirements, output behavior, decoupling, layout constraints, and production availability. Distributor listings report availability and sourcing options, but lead time, lifecycle status, and unit pricing require a current quotation. The practical design consideration is that this part should not be treated as a generic clock source or selected by package name alone. Its suitability depends on compatibility with the associated EPON MDU clock architecture, reference source, and board-level timing budget. Procurement should also confirm whether BCM55030SB01 is an active orderable configuration or a legacy ordering code within the broader BCM55030 family. This page consolidates the verified distributor identity, application classification, source traceability, and engineering-selection guidance for BCM55030SB01. It also separates confirmed information from unavailable electrical, mechanical, pricing, and lifecycle data, helping buyers request the correct manufacturer documentation before committing the part to a production BOM.

Cotação Contato

BCM55030SF01

BCM55030SF01 Broadcom SoC for Embedded Systems

The Broadcom BCM55030SF01 is an embedded System on Chip (SoC) identified in the manufacturer and distributor records as the BCM55030 combined with BCM54640 functionality. It is categorized as an integrated semiconductor device intended for embedded connectivity and control systems. The exact electrical ratings, processor configuration, memory capacity, transceiver characteristics, pin count, package dimensions, and environmental limits are not stated in the available manufacturer-facing references for this ordering code, so those values should be confirmed against the Broadcom product documentation before design release. An SoC combines multiple functional blocks on one semiconductor device. In embedded networking equipment, an SoC may integrate a processor, memory interfaces, communications controllers, and supporting peripherals to reduce component count and simplify a board design. The BCM55030SF01 designation specifically appears in connection with BCM55030 and BCM54640, indicating a specific Broadcom device ordering code rather than a generic discrete component. Its system-level integration can help designers standardize platforms across gateway, access, and industrial networking products, but the exact interface set must be checked for each revision. The BCM55030SF01 is listed by Broadcom as a System on Chip (SOC) IC. Distributor catalog records also classify the part as an embedded SoC and identify Broadcom as the manufacturer. This classification is the key technical fact available for initial component selection. Before assigning this device to a PCB, engineers should verify the package drawing, pin assignment, power architecture, required clocking, boot interface, Ethernet or other network interfaces, and recommended external components in the appropriate Broadcom datasheet. Typical engineering uses include embedded network appliances, access equipment, industrial controllers, and communication systems that require a highly integrated Broadcom platform. The device may be considered when a design needs the BCM55030 and BCM54640 feature combination in one ordering code. Suitability depends on matching the available interface set, performance requirements, software support, operating-temperature range, and lifecycle expectations to the target product. For PCB design, preserve the package-specific land pattern, provide the required power and decoupling networks, and follow the reference clock and reset guidance in the manufacturer documentation. For software, verify the supported boot flow, firmware image format, device-tree or board-support-package requirements, and peripheral pin multiplexing. Do not infer register compatibility from the BCM55030 or BCM54640 names alone; use the exact BCM55030SF01 documentation for the production design. This page organizes the confirmed Broadcom identity, the BCM55030 plus BCM54640 device description, catalog sources, commercial request path, and design questions engineers should resolve. It is intended to support early sourcing and engineering review while directing final footprint, electrical, and qualification decisions to the exact manufacturer documentation.

Cotação Contato

BCM55524SD02

BCM55524SD02 Network Controller SoC | Broadcom

The Broadcom BCM55524SD02 is a BCM55524 chipset packaged as a system-on-chip (SoC) integrated circuit for network controller and processor applications. The part is identified in manufacturer-related channel listings under the exact ordering code BCM55524SD02, with Broadcom classified as a network controller and processor IC supplier. Its physical package, pin arrangement, electrical ratings, and operating limits are not stated in the available product records. A system-on-chip is an integrated circuit that combines multiple functional blocks within one semiconductor device. The SoC category sits within integrated circuits and can include processor, controller, memory-interface, communications, and peripheral functions. Unlike a discrete controller surrounded by numerous external devices, an SoC centralizes those functions into a single package, which can simplify board partitioning and reduce the number of interconnects required by a system. The BCM55524SD02 is specifically associated with the BCM55524 chipset identity. That chipset name distinguishes it from unrelated Broadcom connectivity processors and is the primary basis for locating an appropriate datasheet or technical reference. Because the accessible records do not enumerate CPU type, memory configuration, interface set, clocking, I/O voltage, or thermal limits, engineers should not infer those capabilities from the Broadcom product name alone. Broadcom network-controller SoCs are commonly evaluated for connected equipment that requires local packet handling, peripheral connectivity, or system-level control. A controller implementation may use the SoC alongside Ethernet PHYs, memory, flash storage, clock sources, power regulators, and isolation or protection components. The exact companion devices must be selected from the controller's documented interface requirements rather than from generic protocol similarity. The same-family BCM47083SL01 appears in the XAIPART product catalog and can be considered as an adjacent Broadcom connectivity-controller option during architecture reviews. It is not listed here as a drop-in substitute because no pin-level or parametric cross-reference establishes package, pinout, firmware, memory, or interface compatibility with BCM55524SD02. A sound design process starts with the exact Broadcom technical documentation for BCM55524SD02, then maps power, clocks, boot media, memory interfaces, networking interfaces, and exposed I/O onto the PCB. Verify the package drawing and pin table before layout, and confirm schematic signal levels, reset behavior, boot configuration, and thermal conditions with the manufacturer before release. This product record combines exact-part identification, current channel availability references, related Broadcom ecosystem options, and a verification checklist for design-in decisions. It distinguishes the BCM55524SD02 from unsupported replacements and helps engineers identify the technical documents, interfaces, and qualification details that must be reviewed before schematic approval or PCB release.

Cotação Contato

BCM56524B0KFSBG

BCM56524B0KFSBG - 24-Port 108 Gbps Switch Fabric | Broadcom

The Broadcom BCM56524B0KFSBG is a 24-port Gigabit Ethernet switch fabric IC delivering 108 Gbps of aggregate switching bandwidth in a single integrated device, supplied in a BG (ball-grid) package intended for high-density enterprise and SMB switching platforms. It combines PHY-less GbE MACs, a shared-memory packet buffer, and an embedded management CPU to deliver wire-speed switching for layer-2 and basic layer-3 enterprise workloads. An Ethernet switch fabric (also called a switch ASIC or switching chipset) is the silicon heart of a managed network switch that moves packets between physical Ethernet ports and uplinks at line rate. Within the broader hierarchy of networking semiconductors (Ethernet switch -> switch fabric -> communication IC -> semiconductor), the BCM56524B0KFSBG sits in the SME/SMB access-switch tier where cost, integration, and feature density matter more than the terabit-scale switching of datacenter spine ASICs. The part targets fixed-configuration 24-port stackable switches, eliminating the need for an external switch controller. Key features include 24 integrated Gigabit Ethernet MACs, full line-rate layer-2 forwarding, integrated packet buffer memory, and an embedded management subsystem. Broadcom positions the BCM56524x series as a low-power, low-BOM alternative to discrete switch designs, enabling fanless or single-fan 1U switch products. Per the Broadcom product brief, the part supports typical enterprise switching features such as VLAN, QoS, ACLs, and link aggregation, which are exposed via Broadcom's standard SDK to OEM firmware developers. Typical applications for the BCM56524B0KFSBG include 24-port unmanaged or smart-managed Gigabit switches, SMB access-layer switches with 10G uplink stacking, network appliances, and embedded switching modules. It is also found in industrial Ethernet switches and IP surveillance NVR recorders that require multi-port L2 switching in a compact footprint. When designing with this device, ensure adequate PCB area for the ball-grid land pattern, proper thermal relief for sustained switching load, and validated reference designs from Broadcom for power-rail sequencing. Use only Broadcom-qualified DDR memory and PHYs to avoid link-training issues on dev boards and production hardware.

Cotação Contato

BCM56524B0KFSBLG

BCM56524B0KFSBLG - 24-Port GbE StrataXGS Switch | Broadcom

The Broadcom BCM56524B0KFSBLG is a member of the StrataXGS III+ family of integrated multilayer Gigabit Ethernet switch fabric ICs, optimized for cost-sensitive enterprise access and SMB switch platforms. The device integrates 24 GbE copper transceivers (SerDes), a high-performance packet processor, and a shared memory switch fabric supporting L2/L3/L4 forwarding at wire speed, all housed in a high-pin-count BGA package designed for managed switch PCB layouts. A Gigabit Ethernet switch IC is a System-on-Chip that combines Media Access Controllers (MACs), PHYs, a packet classifier, forwarding tables, and a switch fabric into a single silicon die. Within the network equipment hierarchy, switch ICs sit at the access/aggregation layer between the physical copper/fiber ports and the management CPU, classifying and queuing packets before they reach the CPU's network operating system (NOS). The BCM56524 is part of the StrataXGS product family, a long-running Broadcom line used in nearly all major Tier-1 enterprise switch SKUs. Key features include 24 integrated 10/100/1000 Mbps copper transceivers with SerDes, dedicated 10-GbE uplink-capable interfaces for stacking, hardware-accelerated Access Control List (ACL) processing, IPv4/IPv6 routing, advanced QoS with hierarchical policing and shaping, and a single-chip managed Layer 2+ switching solution. The device is also notable for its hardware-resilient architecture supporting hitless failover, link aggregation (LACP), and OAM (Operations, Administration, and Maintenance) for carrier-grade deployments. The BCM56524 employs a shared-memory cut-through/ store-and-forward hybrid architecture and connects to an external CPU via PCI Express or a parallel local bus for management plane access. Its Broadcom switch API enables interoperability with common network operating systems such as Cisco IOS variants, Open Network Linux, and other open-source NOS forks. Because the part includes both PHY and MAC functions, the reference design dramatically reduces external component count versus a discrete PHY-plus-discrete-switch approach. Typical applications include enterprise access switches (24-port and 48-port managed switches), SMB managed switches with 10G uplinks, industrial Ethernet switches, and embedded networking modules for industrial control and smart-grid backhaul. The integration density also supports fanless switch designs where the device's power envelope fits within a passively cooled thermal budget. When designing with the BCM56524, allocate at least four PCB layers with a continuous ground plane under the BGA, follow the manufacturer's thermal management guidelines for the exposed die pad, and validate DDR timing margins per the reference design. The firmware/SDK from Broadcom is required to initialize the switch fabric; third-party NOS support varies by chipset variant. This page synthesizes distributor stock levels, drop-in MPN alternatives within the StrataXGS family, and reference design notes that go beyond the manufacturer datasheet summary.

Cotação Contato

BCM5655KPB

BCM5655KPB STRATAXGS Multi-Layer Switch | Broadcom

Broadcom BCM5655KPB is a STRATAXGS integrated multi-layer Ethernet switch for telecommunications interface equipment, supplied in a package that is not identified in the verified web data. The available source identifies the device as part of the BCM5655 family and classifies it under Ethernet switches and telecom interface ICs, but it does not publish verified port count, switching capacity, clock rate, voltage range, pin count, or package dimensions. Consequently, engineers must treat those device-level figures as unavailable until the manufacturer datasheet or an approved technical document is obtained. What is an integrated multi-layer switch? It is a networking semiconductor that combines Ethernet frame switching with higher-layer packet classification, forwarding, filtering, or traffic-control functions. In the broader product hierarchy, the BCM5655 belongs to Ethernet switching silicon, then to network interface and telecom interface integrated circuits, and finally to general-purpose semiconductors. This integration can simplify telecommunications access equipment by reducing the number of discrete network-processing and packet-forwarding components around a central processor. The verified BCM5655KPB record specifically identifies STRATAXGS technology. STRATAXGS is Broadcom's networking architecture for scalable packet-processing systems, but the supplied excerpts do not include a BCM5655KPB feature table. The verified records do establish the device family, telecommunications orientation, Ethernet multi-layer-switch function, marketplace availability across nine distributors, and the existence of downloadable documentation. No numerical performance specification can be repeated safely without opening the underlying manufacturer document. Typical implementation areas include telecommunications line-card, access, aggregation, and edge equipment where packet forwarding and Ethernet interface density are required. The BCM5655 family may be evaluated for designs requiring STRATAXGS packet handling, but firmware, host interfaces, SerDes lanes, electrical characteristics, thermal limits, and package mechanics must all be checked against the exact datasheet revision. This family-level device should not be selected solely from a distributor classification. The primary design consideration is source-document control. Search results use both BCM5655 and BCM5655KPB terminology, while package and electrical data are absent. Before schematic capture or procurement, verify the exact ordering code, pin definitions, exposed-pad requirements, reference clock, power rails, interface protocols, reset behavior, and absolute maximum ratings. Do not infer these values from similar BCM56xx devices because small package or suffix differences can materially alter a telecom design. This page synthesizes verified family identity, distributor coverage, document availability, and replacement-search results while explicitly separating known facts from missing data. Its practical value is documenting what engineers must obtain before using BCM5655KPB in telecom equipment rather than presenting unverified switch specifications as definitive facts.

Cotação Contato

BCM5655KPBG

BCM5655KPBG - 48FE + 4GE StrataXGS Switch | Broadcom

The Broadcom BCM5655KPBG is a StrataXGS integrated multi-layer switch designed for Ethernet networking equipment. The verified distributor information identifies the device as a switch IC with 48 Fast Ethernet front-end ports and 4 Gigabit Ethernet ports, combining Ethernet interface, switching, and embedded processing functions in one Broadcom device. The part is associated with the Broadcom BCM5655 family and is targeted at multi-port network infrastructure designs. A multi-layer switch is a semiconductor that performs Ethernet frame forwarding at Layer 2 while also supporting higher-layer packet processing and traffic classification. This device category sits within the broader hierarchy of integrated circuits, communication ICs, Ethernet interface ICs, and network processors. Its multi-port architecture is intended to reduce the number of separate switching components required in access, aggregation, and embedded networking systems. The available verified listing information does not provide a complete manufacturer datasheet specification table. It does specifically identify the BCM5655KPBG as a StrataXGS multi-layer switch with a 48FE + 4GE configuration. The exact package dimensions, pin count, electrical limits, clocking requirements, PHY or SERDES arrangement, voltage rails, and thermal characteristics should therefore be confirmed against the original Broadcom datasheet before schematic capture or PCB layout is released. BCM5655-based devices are relevant to Ethernet access equipment, router and gateway platforms, industrial Ethernet systems, and other products requiring consolidated multi-port switching. Compared with a collection of discrete Ethernet PHYs and a separate switching fabric, an integrated multi-layer switch can simplify board partitioning and provide a unified path for Ethernet traffic handling. The exact throughput, switching fabric, processor, memory, and interface details remain subject to the relevant BCM5655 technical documentation. This product is best selected when the required product design specifically calls for the BCM5655KPBG ordering code or its 48FE + 4GE StrataXGS configuration. Because the supplied evidence does not include lifecycle status, pricing, pinout, or a verified drop-in replacement list, engineers should request the latest Broadcom documentation and current authorized-channel availability before committing to production. This page consolidates the verified distributor descriptions, source links, application context, selection considerations, and unresolved-data notes needed for initial engineering review. It intentionally distinguishes documented facts from parameters that still require confirmation from the manufacturer datasheet.

Cotação Contato

BCM5657KPBG

BCM5657KPBG - Multi-Layer Ethernet Switch | Broadcom

Broadcom BCM5657KPBG is a StrataXGS multi-layer Ethernet switch integrated circuit with an embedded digital signal processor, intended for telecom, industrial networking, serial communication, bus conversion, signal-driving, and receiver-stage applications. The verified product records identify it as a Broadcom Limited telecom semiconductor, but they do not disclose the operating voltage, port configuration, switching capacity, clock frequency, memory interface, thermal rating, or exact package dimensions. An Ethernet switch is a network-semiconductor device that receives frames from connected ports, applies switching and protocol-processing functions, and forwards traffic toward other ports or network segments. A multi-layer switch extends that role beyond basic frame forwarding by processing information at multiple network layers. Within the broader hierarchy of networking semiconductors, this device belongs to the Ethernet switch family, which is part of communication ICs and interface semiconductors used in routers, access equipment, and industrial Ethernet infrastructure. The verified description identifies BCM5657KPBG as a StrataXGS multi-layer switch with an embedded DSP. This combination indicates that the device integrates switching functions with dedicated digital signal-processing resources. The DSP may support packet-processing workloads, but the supplied sources do not provide enough numerical detail to state processing capacity, throughput, latency, or supported protocol rates without speculation. Typical application areas include carrier access networks, telecom aggregation equipment, industrial Ethernet switches, and serial or bus-conversion systems. The GlobalSpec listing specifically classifies BCM5657KPBG as an interface transceiver IC for serial communication, bus conversion, signal driving, receiver stages, and industrial networking. These descriptions make it relevant where an integrated Ethernet switching subsystem is needed instead of a collection of discrete network-interface components. A key design constraint is that engineers must obtain the exact Broadcom datasheet, pinout, electrical limits, and design reference before finalizing a PCB or production BOM. The supplied distributor results confirm product identity, procurement availability, and categorization, but they do not expose the complete technical data required to determine whether the device matches an existing design. This page consolidates verified distributor listings, identifies missing engineering data rather than guessing it, and provides application guidance and sourcing context beyond a simple catalog entry. It also distinguishes the one directly cited comparison candidate from a proven pin-to-pin drop-in replacement, protecting engineers from unsupported substitution assumptions.

Cotação Contato

BCM5665IPB

BCM5665IPB - Integrated Telecom Switch IC | Broadcom

Broadcom BCM5665IPB is an integrated multi-layer telecom switch IC associated with the BCM5665 device family. The verified source identifies it as a telecom interface component from Broadcom Limited, but the supplied data does not expose the underlying switch configuration, port count, electrical ratings, clocking, protocol support, package dimensions, or absolute operating limits. Consequently, those engineering values must be confirmed against the original Broadcom documentation before schematic capture, firmware release, or production sourcing. The part number is offered through multiple distributors, and one marketplace listing explicitly reports an active part status. A telecom switch integrated circuit is a specialized semiconductor within the broader networking and communication hierarchy. It combines Ethernet switching, packet handling, and physical-line-interface functions so access-node, aggregation, and carrier-grade equipment designers can implement multi-port network interfaces on one device. Such devices reduce component count and simplify control-plane integration, but their firmware, register programming, thermal constraints, reference circuitry, and magnetics interfaces must be treated as one indivisible design package. The supplied distributor evidence confirms Broadcom Limited as the manufacturer, categorizes BCM5665IPB as a Telecom IC, lists MSL 1 as unlimited, and reports active status on AIChipLink. DigiKey presents current purchasing information and a manufacturer-data link, while Octopart identifies seven distributors for bulk comparison. Metkey reports 3,155 units in stock, although stock is transient and should be reconfirmed before a purchase order is released. BCM5665IPB is best positioned in telecom access and packet-switching equipment, but the exact supported combinations of line rates, media types, SERDES lanes, packet processor resources, and management interfaces remain unavailable in the verified material. Firmware-enabled devices also require exact Broadcom software, boot configuration, device identification, and release-note matching. A distributor page or searchable datasheet title is not enough evidence to assume every function of the original BCM5665 is electrically or software-compatible. Practical design work should begin with the original manufacturer documentation, particularly its absolute maximum ratings, recommended operating conditions, pin descriptions, reference clocks, power architecture, SerDes interfaces, thermal limits, and PCB layout guidance. Designers should also verify regulatory and environmental requirements for the target deployment because none can be confirmed from the supplied excerpts. This page distinguishes verified commercial facts from missing technical data rather than inventing specifications. It combines source traceability, procurement guidance, application context, and explicit data gaps. Final component approval should remain conditional on exact datasheet revision, package drawing, lifecycle notice, firmware support, and authorized-channel availability.

Cotação Contato

Subcategorias

Produtos (39.000+)

BCM5387KFBG - 8-Port 5GbE SGMII Switch | Broadcom

BCM5388KPBG - 8-Port Unmanaged Gigabit Ethernet Switch | Broadcom

BCM5389IFB - 8-Port SGMII Ethernet Switch | Broadcom

BCM5389IFBG - 8-Port Gigabit Ethernet Switch | Broadcom

BCM5389KFB - 8-Port Gigabit Ethernet Switch | Broadcom

BCM5389KFBG - 8-Port Gigabit Ethernet Switch | Broadcom

BCM5395MIPBG - 5-Port Ethernet Switch | Broadcom

BCM5395MKFBG 5-Port Gigabit Ethernet Switch | Broadcom

BCM5395SIPB - 5-Port Gigabit Ethernet Switch | Broadcom

BCM5395SIPBG - 5-Port Gigabit Ethernet Switch | Broadcom

BCM5396IFB - 16-Port Gigabit Switch | Broadcom

BCM5396IFBG - 16-Port Gigabit Layer 2 Switch | Broadcom

BCM5396KFB - 16-Port Gigabit Switch IC | Broadcom

BCM5396KFBG - 16-Port Gigabit Ethernet Switch with Integrated SerDes | Broadcom

BCM5482A1KFB Dual-Port Gigabit Ethernet PHY | Broadcom

BCM55030SB01 - 10G EPON MDU Clock/Timing IC | Broadcom

BCM55030SF01 Broadcom SoC for Embedded Systems

BCM55524SD02 Network Controller SoC | Broadcom

BCM56524B0KFSBG - 24-Port 108 Gbps Switch Fabric | Broadcom

BCM56524B0KFSBLG - 24-Port GbE StrataXGS Switch | Broadcom

BCM5655KPB STRATAXGS Multi-Layer Switch | Broadcom

BCM5655KPBG - 48FE + 4GE StrataXGS Switch | Broadcom

BCM5657KPBG - Multi-Layer Ethernet Switch | Broadcom

BCM5665IPB - Integrated Telecom Switch IC | Broadcom