Circuitos Integrados

LSF0101

LSF0101 - 1-Bit Auto-Bidirectional Level Translator | Texas Instruments

The Texas Instruments LSF0101 is a single-channel auto-bidirectional multi-voltage level translator for open-drain and push-pull applications, housed in an ultra-compact 6-X2SON (1 x 0.8 mm) package. It translates between voltage domains without a direction pin, minimizing system design effort for buses such as PMBus, I2C, and SMBus. A level translator (also called a voltage shifter or logic-level converter) is an interface IC that safely connects circuits operating at different supply voltages - for example a 1.8 V microcontroller communicating with a 3.3 V or 5 V peripheral. Level translators belong to the broader voltage translator / logic IC hierarchy within interface semiconductors, and the LSF0101 is the smallest, single-bit member of the TI/Nexperia LSF family. Key features include automatic bidirectional operation with no DIR control signal, up-translation of up to 100 MHz and down translation of 100 MHz or more at a capacitive load of 30 pF or less, and 5 V tolerant I/O pins for TTL compatibility. According to the TI and Nexperia datasheets, the pass-gate (NFET) switch architecture delivers very low propagation delay and supports both open-drain two-wire buses and push-pull interfaces. The reference-bias topology (VREF_A / VREF_B) defines the two voltage domains; the low-side reference is applied through the EN pin bias network and an analog pass switch connects the A and B pins. This makes the LSF0101 especially suitable for two-wire buses where direction changes asynchronously - something buffered push-pull translators cannot handle without a direction input. Typical applications include I2C, SMBus, and PMBus level shifting, 1.8 V to 3.3 V or 5 V mixed-voltage MCU peripherals, industrial control buses, and mobile or wearable designs where the 1 x 0.8 mm X2SON footprint conserves board area. Design consideration: the LSF family requires correct pull-up resistor sizing on open-drain buses to meet rise-time targets; the reference-side bias resistor (typically 200 kohm per TI datasheet guidance) sets translation speed, so verify its value against bus capacitance and data rate before production.

Cotação Contato

LSF0102-Q1

LSF0102-Q1 - 2-Ch Auto Bidirectional Level Translator | TI

The Texas Instruments LSF0102-Q1 is an automotive-qualified, 2-channel auto bidirectional multi-voltage level translator for open-drain and push-pull applications, packaged in an 8-pin VSSOP (DCU). It operates from 0.95 V to 5.5 V on Vref_A and 1.8 V to 5.5 V on Vref_B, enabling bidirectional translation between 0.95 V and 5.5 V without a direction pin. Data inputs are 5-V tolerant. A voltage level translator is a logic IC that converts signal voltage levels between circuits operating at different supply rails, sitting within the broader hierarchy of voltage translators -> logic ICs -> interface semiconductors. The LSF family uses a pass-gate (transmission-gate) architecture with reference rails, distinguishing it from powered translator families such as TXS/TXB that use MOSFET output stages. Key features include up to 100 MHz up translation and greater than 100 MHz down translation with capacitive loads of 30 pF or less; at a 50 pF load the device supports up to 40 MHz in both directions. This bandwidth covers standard automotive interfaces such as I2C, SPI, GPIO, SDIO, UART, and MDIO. AEC-Q100 qualification makes it suitable for automotive environments. The auto-direction architecture requires no direction-control pin, reducing MCU GPIO overhead and eliminating direction-timing errors. Because the LSF core is a passive pass-gate structure, external pull-up resistors set logic levels on open-drain buses; for push-pull signals, the reference rails Vref_A and Vref_B define the translated levels directly. Typical applications include automotive infotainment I2C buses between 1.8 V SoCs and 3.3 V peripherals, SPI connections between low-voltage MCUs and 5 V sensors, and SDIO/GPIO interfaces in body electronics and cluster modules. Design consideration: because the LSF topology needs external pull-up resistors on open-drain nets, size them against total bus capacitance and target rise time; keep capacitive loading at or below 30 pF to exploit the full 100 MHz translation rate.

Cotação Contato

LSF0102DDFR

LSF0102DDFR - 2-Ch 100Mbps Level Translator | TI

The Texas Instruments LSF0102DDFR is a dual-channel auto-bidirectional multi-voltage level translator supporting both open-drain and push-pull applications. Housed in an 8-pin TSOT-23-8 (DDF) package, it translates signals between voltage domains from 0.95V up to 5.5V at data rates up to 100 Mbps without requiring a direction control pin. A level translator, or voltage level shifter, is a logic IC that enables digital signals to safely cross between circuits operating at different supply voltages, such as 1.8V, 3.3V, and 5V domains. Within the hierarchy of logic ICs, translators sit alongside buffers and bus switches in the signal-interface layer of a system, ensuring reliable communication in mixed-voltage designs. Key features include fully automatic bidirectional translation with no direction pin, support for open-drain buses (I2C, SMBus) and push-pull interfaces (SPI, UART), a wide 0.95V to 5V translation range, and ultra-low quiescent current of 6 uA typical. The fast propagation delay preserves signal timing in high-speed links up to 100 Mbps. Technically, the LSF0102 uses a pass-gate (transmission-gate) architecture. The reference pins VREF_A and VREF_B set the logic levels on each side, and external pull-up resistors define the high levels of each domain. The device senses data direction automatically, making it transparent to the host system and reducing pin count and firmware complexity compared to directional translators. Typical applications include I2C and SMBus level shifting between 1.8V, 3.3V, and 5V domains, SPI and UART interfaces in mixed-voltage embedded systems, general-purpose GPIO translation, and battery-powered portable devices where the 6 uA quiescent current minimizes standby drain. Design consideration: pull-up resistor values directly trade off maximum data rate against power consumption; use lower resistance (1-2 kilohm) for high-speed push-pull operation and higher resistance (4.7-10 kilohm) for low-power open-drain buses.

Cotação Contato

LSF0108PWR

LSF0108PWR - 8-Ch Bidirectional Level Translator | TI

The Texas Instruments LSF0108PWR is an 8-channel auto-bidirectional multi-voltage level translator for open-drain and push-pull applications, housed in a 20-pin TSSOP (PW) package. Both A-side and B-side ports support 0 V to 5 V, with approximately 1.5 ns propagation delay, making it suitable for I2C, SMBus, UART, and SPI interfaces. A voltage level translator is an interface IC that lets digital signals in different voltage domains communicate safely by shifting signal levels as they pass between two logic families. Within the system hierarchy, a level translator is a type of logic interface IC within the broader integrated circuits category. The LSF0108 uses a pass-gate (series MOSFET) architecture with external pull-up resistors, providing automatic direction sensing without a direction-control pin. Key features include bidirectional translation without a direction pin, support for both open-drain and push-pull drivers, and an operating temperature range of -40C to +125C. The LSF family covers the 0.95 V to 5 V translation range, spanning nearly all common logic levels (1.2V, 1.8V, 2.5V, 3.3V, 5V). Low standby current and the compact TSSOP-20 footprint suit space-constrained mixed-voltage boards. Technically, each channel employs a series pass transistor. Direction is determined automatically by whichever side drives, eliminating direction-control signals and simplifying firmware. The reference side (VREF_A or VREF_B) sets the lower voltage domain; pull-up resistors on the opposite side set the higher domain. Typical applications include I2C bus level shifting between 1.8V and 3.3V or 5V domains, UART interfacing between microcontrollers and peripherals, SPI communication between different logic voltages, and mixed-voltage sensor or memory interfaces. Design tip: size external pull-up resistors according to bus capacitance and target speed (1-10 kOhm for 400 kHz I2C). Correct VREF sequencing at power-up is essential; refer to TI datasheet SCPS229 for power-up requirements.

Cotação Contato

LSF0108QPWRQ1

LSF0108QPWRQ1 - Auto 8-Ch Bidirectional Level Shifter | TI

The Texas Instruments LSF0108QPWRQ1 is an automotive-grade, 8-channel bidirectional multi-voltage level translator for open-drain and push-pull applications. It translates between voltage domains from 0.95V to 5V without a direction pin, housed in a 20-pin TSSOP (PW) package and rated for -40C to +125C operation per AEC-Q100. A level translator, or voltage level shifter, is an interface IC that enables digital communication between circuits operating at different supply voltages. It sits between a low-voltage controller, such as a 1.8V MCU, and a higher-voltage peripheral, such as a 3.3V sensor, ensuring logic levels are interpreted correctly. Level translators belong to the broader interface IC family, and the LSF family uses a pass-gate (N-MOSFET) architecture with external pull-up resistors, allowing automatic bidirectional translation without direction control. Key features include bidirectional operation with no direction pin, voltage support from 0.95V to 5V, and compatibility with both open-drain buses like I2C and push-pull signals. The device supports up to 100 MHz up-translation and greater than 100 MHz down-translation at <=30 pF load, and 40 MHz up/down translation at 50 pF load, per the TI datasheet (Rev. H). Technically, each channel uses a single N-channel MOSFET with external pull-ups defining the high level on each side. When either side drives low, the MOSFET conducts and pulls the opposite side low through the resistor network, enabling automatic bidirectional shifting. This removes GPIO overhead for direction signaling and simplifies firmware in multi-voltage systems. Typical applications include automotive body control modules, infotainment systems, MDIO management buses, and sensor interfaces where 1.8V, 2.5V, 3.3V, and 5V domains coexist, plus industrial automation mixed-voltage links. Design tip: select pull-up resistor values according to bus capacitance and speed; lower values improve edge rates but raise current consumption, and VREF pins must be tied to the respective rails to set translation levels correctly.

Cotação Contato

LSF0204RUTR

LSF0204RUTR - 4-Bit Bidirectional Level Translator | Texas Instruments

The Texas Instruments LSF0204RUTR is a 4-bit bidirectional multi-voltage level translator for open-drain and push-pull interfaces, housed in a 12-pin UQFN (RUT) package measuring 1.7 mm x 2.0 mm. The device operates with Vref_A from 0.8 V to 4.5 V and Vref_B from 1.8 V to 5.5 V, supporting bidirectional translation between any voltages from 0.8 V to 5.0 V without a direction pin. Typical data-rate capability exceeds 100 MHz in push-pull mode, making it suitable for SD card, SIM card, I2C, SPI, GPIO, and UART bridging. A bidirectional voltage level translator (also called a level shifter or logic-level translator) is an interface IC that connects two logic domains operating at different supply voltages. The LSF0204 belongs to the broader category of voltage translators, which are themselves a sub-category of interface ICs used in mixed-voltage digital systems. Because modern SoCs, microcontrollers, and sensors frequently operate at voltages other than 5 V (1.8 V, 3.3 V, 1.2 V), translators are essential glue logic that prevents damage and signal-integrity problems when devices of different voltage domains must communicate. Key features of the LSF0204 include 4 channels per package, support for both open-drain (I2C-style) and push-pull (SPI, GPIO) topologies, automatic direction sensing without a DIR pin, and an operating temperature range of -40 °C to +125 °C. The wide voltage range combined with auto-bidirectional operation eliminates the firmware burden of direction control and reduces BOM cost by removing external pull-up/down components on most paths. The compact UQFN-12 footprint is well-suited for space-constrained wearables, mobile devices, and IoT modules. Architecturally, the LSF0204 uses TI's pass-gate-based translator topology with internal one-shot accelerators that improve rise/fall time when driving capacitive bus loads. This edge-rate enhancement enables clean signals at higher bus speeds than a pure passive FET translator, while still drawing minimal quiescent current. The part supports hot-insertion because both reference rails can be ramped independently, and Ioff (partial-power-down) protection prevents back-feeding when either rail is off. Typical applications include SD card level shifting between a 1.8 V host SoC and a 3.3 V card, I2C bus translation in multi-voltage sensor hubs, SPI bridging between a low-voltage MCU and 5 V peripherals, SIM/UIM card interfaces, and general-purpose GPIO expansion across voltage domains. The wide voltage window makes it equally well-suited for legacy 5 V systems and modern sub-2 V processors. When designing with the LSF0204, the engineer should observe one practical rule: pull-up resistors are required on each side for open-drain buses (I2C), with values selected to meet the rise-time budget of the target bus speed; push-pull signals do not require pull-ups but the reference rails must both be present for reliable operation. Place both Vref_A and Vref_B decoupling capacitors within 2 mm of the IC pins. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato

LT1001CD

LT1001CD - Precision Op-Amp 8-SOIC | Texas Instruments

The Texas Instruments LT1001CD is a precision operational amplifier with industry-leading DC accuracy, supplied in an 8-pin SOIC (D) package. It features a maximum input offset voltage of 110 uV, a unity-gain bandwidth of 0.8 MHz, and a low offset voltage drift of 0.3 uV/C. The single-channel amplifier is built for instrumentation, precision signal conditioning, and industrial measurement front ends. A precision op-amp is a type of operational amplifier designed to minimize the input-referred errors (offset voltage, bias current, drift, and noise) that limit DC accuracy. In the system hierarchy, the LT1001CD sits at the precision tier of general-purpose amplifiers, above standard 741-class parts and below chopper-stabilized zero-drift amplifiers. It is the workhorse of 16-bit and lower data-acquisition front ends, weigh scales, strain-gauge bridges, and thermocouple conditioning circuits where 10-100 uV of error must be resolved over industrial temperature ranges. Key features of the LT1001CD include 110 uV maximum input offset voltage, 4 nA maximum input bias current, 102 dB minimum open-loop gain, and 0.3 uV/C offset voltage drift. The device operates from +/-3 V to +/-18 V dual supplies or 6 V to 36 V single supply. Its bipolar input stage supports true differential sensing across the full input common-mode range, including ground-referenced signals when operated from a single supply. The C-grade commercial temperature range is 0C to +70C. Architecturally, the LT1001CD uses a precision bipolar input stage with active bias compensation, allowing it to maintain low offset and bias current over temperature without chopper-induced switching artifacts. The internal compensation network is unity-gain stable, eliminating the need for external compensation capacitors. The result is a versatile amplifier that combines 741-class simplicity with significantly tighter DC specifications. Typical applications include precision weighing scales, strain-gauge and load-cell amplifiers, thermocouple and RTD signal conditioning, medical instrumentation front ends, 16-bit SAR ADC input buffers, industrial process-control analog inputs, and reference-voltage buffering for precision DACs. The 8-SOIC package is footprint-compatible with industry-standard dual op-amps, simplifying board reuse in legacy designs. When designing with the LT1001CD, take care to provide adequate supply decoupling (100 nF ceramic close to each supply pin) and route sensitive bias-current paths to avoid leakage. Optional pins 1 and 8 support external offset nulling via a 10 kOhm potentiometer; if unused, leave them open. The input common-mode range extends to the negative supply, making true ground sensing possible on a single rail. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. The information is anchored to the official Analog Devices LT1001 datasheet and cross-checked against Rochester Electronics, DigiKey, and JAK Electronics stock data as of 2026-10-22.

Cotação Contato

LT1001CDR

LT1001CDR - Precision Op-Amp 8-SOIC | Texas Instruments (Tape & Reel)

The Texas Instruments LT1001CDR is a precision operational amplifier with industry-leading DC accuracy, supplied in an 8-pin SOIC (D) package. It features a maximum input offset voltage of 110 uV, a unity-gain bandwidth of 0.8 MHz, and a low offset voltage drift of 0.3 uV/C. The single-channel amplifier is built for instrumentation, precision signal conditioning, and industrial measurement front ends. A precision op-amp is a type of operational amplifier designed to minimize the input-referred errors (offset voltage, bias current, drift, and noise) that limit DC accuracy. In the system hierarchy, the LT1001CDR sits at the precision tier of general-purpose amplifiers, above standard 741-class parts and below chopper-stabilized zero-drift amplifiers. It is the workhorse of 16-bit and lower data-acquisition front ends, weigh scales, strain-gauge bridges, and thermocouple conditioning circuits where 10-100 uV of error must be resolved over industrial temperature ranges. Key features of the LT1001CDR include 110 uV maximum input offset voltage, 4 nA maximum input bias current, 102 dB minimum open-loop gain, and 0.3 uV/C offset voltage drift. The device operates from +/-3 V to +/-18 V dual supplies or 6 V to 36 V single supply. Its bipolar input stage supports true differential sensing across the full input common-mode range, including ground-referenced signals when operated from a single supply. The C-grade commercial temperature range is 0C to +70C. Architecturally, the LT1001CDR uses a precision bipolar input stage with active bias compensation, allowing it to maintain low offset and bias current over temperature without chopper-induced switching artifacts. The internal compensation network is unity-gain stable, eliminating the need for external compensation capacitors. The result is a versatile amplifier that combines 741-class simplicity with significantly tighter DC specifications. Typical applications include precision weighing scales, strain-gauge and load-cell amplifiers, thermocouple and RTD signal conditioning, medical instrumentation front ends, 16-bit SAR ADC input buffers, industrial process-control analog inputs, and reference-voltage buffering for precision DACs. The 8-SOIC package is footprint-compatible with industry-standard dual op-amps, simplifying board reuse in legacy designs. When designing with the LT1001CDR, take care to provide adequate supply decoupling (100 nF ceramic close to each supply pin) and route sensitive bias-current paths to avoid leakage. Optional pins 1 and 8 support external offset nulling via a 10 kOhm potentiometer; if unused, leave them open. The input common-mode range extends to the negative supply, making true ground sensing possible on a single rail. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. The information is anchored to the official Analog Devices LT1001 datasheet and cross-checked against Rochester Electronics, DigiKey, and JAK Electronics stock data as of 2026-10-22.

Cotação Contato

LT1001CH

LT1001CH - 110dB Precision Operational Amplifier | Analog Devices

Analog Devices LT1001CH is a precision operational amplifier featuring 700 pA input bias current, 110 dB open-loop gain, and operation from -3 V to +18 V, housed in an 8-pin TO-5 metal-can package. The LT1001 is designed for instrumentation and other signal-conditioning systems where low bias current, high gain, and low distortion are important. The CH ordering code identifies the commercial-temperature, 8-pin metal-can configuration. An operational amplifier is a high-gain differential-input amplifier that uses negative feedback to create stable, accurate gain in closed-loop circuits. Within the electronic-component hierarchy, the LT1001 belongs to the precision operational-amplifier family, which combines amplifiers with instrumentation amplifiers, analog signal-chain ICs, and semiconductor devices. Its principal role is to amplify small sensor or measurement signals while minimizing errors introduced by input bias current, offset voltage, and finite gain. The verified manufacturer information highlights three defining characteristics: 700 pA input bias current, 110 dB open-loop gain, and a -3 V to +18 V supply range. The 700 pA bias specification is especially relevant to high-impedance transducers because bias current creates an error voltage across source impedance. The 110 dB gain specification provides substantial open-loop margin for precision feedback networks. Dual-supply operation also allows bipolar input and output signals without requiring separate rail-to-rail biasing arrangements. The LT1001 data sheet describes the device as a precision operational amplifier whose distribution of key parameters was optimized during design, processing, and testing. That emphasis distinguishes it from general-purpose amplifiers in applications where predictable offset, bias current, gain behavior, and low-level signal fidelity matter. The TO-5 metal can offers an eight-pin mechanical format commonly encountered in precision laboratory and instrumentation equipment. Typical uses include low-level sensor front ends, bridge and strain-gauge signal conditioning, precision current-to-voltage conversion, laboratory instrumentation, and low-frequency measurement circuits. Its low 700 pA bias current can reduce loading of high-output-impedance sensors, while its 110 dB open-loop gain can improve closed-loop accuracy when the circuit operates with suitable feedback components and operating conditions. Designers should verify the exact eight-pin TO-5 pinout, offset-trim configuration, common-mode range, output-swing limits, and stability requirements against the manufacturer data sheet before replacing an existing amplifier. Input and feedback resistances must also be selected so their thermal noise and parasitic capacitance do not undermine the intended precision. Decoupling and grounding remain important even for a low-noise precision device because supply and return-path impedance can affect measured output performance. This page combines verified manufacturer and distributor information, package details, selection guidance, and a structured comparison of same-family drop-in options. It distinguishes known characteristics from parameters that still require confirmation from the official LT1001 data sheet, helping engineers evaluate replacement risk without relying on incomplete distributor summaries.

Cotação Contato

LT1001CP

LT1001CP - 110uV Offset, 0.8MHz Precision Op Amp | TI

The Texas Instruments LT1001CP is a precision bipolar operational amplifier with maximum offset voltage of 110 uV, a 0.8 MHz gain-bandwidth product, and one amplifier circuit in an 8-pin PDIP package. The LT1001CP is positioned for instrumentation, sensor, and precision signal-conditioning applications that require low offset voltage and stable closed-loop amplification. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to produce an accurate output proportional to the difference between two input voltages. Within the broader semiconductor hierarchy, an operational amplifier belongs to amplifier ICs, analog and mixed-signal ICs, and power-management-adjacent signal-chain components. Its typical role is to buffer sensors, amplify small voltage differences, and drive downstream analog or digital circuitry. The verified LT1001CP specifications identify a maximum input offset voltage of 110 uV and a 0.8 MHz bandwidth. The low offset specification reduces the output error caused by unequal input voltages in a precision feedback circuit. The 0.8 MHz bandwidth establishes the device's useful small-signal operating range and makes the part appropriate for low-to-moderate-frequency measurement and control paths rather than high-speed signal processing. The LT1001CP uses bipolar construction and is packaged in an 8-pin PDIP. According to distributor records, the package is a rectangular, through-hole DIP with eight terminals and a stated body width of 0.300 inch, or 7.62 mm. Its through-hole construction supports prototyping, educational equipment, laboratory instrumentation, and industrial control boards where socketed assembly or manual rework is useful. Typical applications include precision bridge amplifiers, low-level sensor signal conditioning, laboratory measurement instruments, analog control loops, and general-purpose analog prototyping. The commercial temperature grade identifies the LT1001CP as a general-purpose commercial part. It is also suitable wherever the system can accommodate 0.8 MHz bandwidth and the electrical behavior of the LT1001 family. Designers should verify the complete manufacturer datasheet for supply voltage, input common-mode range, output swing, input bias current, slew rate, noise, supply current, and temperature limits before releasing a production design. Decoupling, grounding, source impedance, and feedback-component selection also determine practical precision more than the maximum offset rating alone. This page combines verified distributor pricing, a clear distinction between the target device and related LT1001 package or temperature options, and practical application guidance. It also identifies unavailable electrical data explicitly rather than estimating it, helping engineers compare the LT1001CP with the actual constraints of a specific analog circuit.

Cotação Contato

LT1007CH

LT1007CH - Low-Noise Precision Op Amp | Analog Devices

Analog Devices LT1007CH is a low-noise, high-speed precision operational amplifier in a TO-5 package. It provides 2.5 nV/√Hz wideband input noise, guaranteed 4.5 nV/√Hz noise at 10 Hz, guaranteed 3.8 nV/√Hz noise at 1 kHz, and a typical 60 nV peak-to-peak 0.1 Hz to 10 Hz noise figure. Its precision specifications include 10 µV offset voltage, 0.2 µV/°C drift, and 130 dB common-mode and power-supply rejection. These characteristics make the LT1007CH suitable for instrumentation, low-level sensor amplification, and precision signal chains where input-referred noise and DC stability are important. The LT1007 family combines low-noise operation with high-speed performance, while the LT1037 variant provides a 60 MHz gain-bandwidth product and is stable for closed-loop gains of 5 or greater. The LT1007CH is offered as a single, general-purpose amplifier circuit in a TO-5 package. The manufacturer's datasheet states that noise, precision, and speed are combined in one monolithic operational-amplifier family, supporting applications requiring both low-frequency noise performance and accurate signal amplification. Care should be taken with grounding, input lead routing, supply bypassing, and thermal management. The datasheet specifically advises minimizing air currents, keeping package leads short, placing the two input leads close together, and maintaining both inputs at the same temperature. Because the verified distributor data does not provide operating-voltage limits, supply current, input bias current, output swing, gain-bandwidth product for the LT1007, or detailed TO-5 pin assignments, those values are not asserted here. Consult the manufacturer datasheet for those parameters, input and output common-mode limits, saturation behavior, compensation requirements, and the exact pin configuration before final circuit design. The LT1007CH is a precision analog building block for equipment where low-noise, low-offset measurement paths are more important than minimum cost or maximum integration.

Cotação Contato

LT1007CJG

LT1007CJG - Low-Noise Precision Op Amp | Texas Instruments

The Texas Instruments LT1007CJG is a single, low-noise precision operational amplifier with 2.5 nV/√Hz wideband input-noise density, 10 µV offset voltage, and 0.2 µV/°C input-offset drift, packaged in an 8-pin CDIP. It combines low-noise performance with high open-loop gain and strong common-mode rejection for accurate analog signal conditioning. An operational amplifier is a voltage-feedback amplifier that uses high differential gain to amplify the difference between its non-inverting and inverting inputs. Within the wider signal-chain hierarchy, the LT1007CJG belongs to the precision amplifier class, which sits between general-purpose amplifiers and instrumentation amplifiers. Its noise and offset characteristics make it suitable when signals must be measured, converted, filtered, buffered, or referenced with little added error. The LT1007 series emphasizes low-noise signal handling with a 1/f noise corner frequency of 2 Hz and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. The 10 µV input-offset voltage and 0.2 µV/°C drift limit input-referred error in slowly varying or high-gain stages. The amplifier also provides 130 dB common-mode rejection and power-supply rejection, reducing sensitivity to supply noise and shared ground-bus disturbances. A unity-gain-stable configuration supports direct signal buffering, while the instrumentation characteristics support precision gain stages. The device is intended for low-level sensor front ends, strain-gage and bridge excitation, precision current-to-voltage conversion, audio and low-frequency measurement circuits, laboratory instrumentation, and high-gain analog systems. Decoupling capacitors should be placed close to the supply pins so switching ripple and high-frequency supply variation do not modulate the output. For DC-sensitive applications, account for input-bias current of 55 nA when working with high-impedance sources. Because the CDIP package has eight through-hole leads, the amplifier fits conventional 0.300-inch, 7.62 mm row spacing and is easy to prototype or socket on laboratory and industrial boards. This page consolidates the LT1007CJG electrical characteristics, package details, design guidance, and drop-in family alternatives into a single engineering reference. Use the pin-description table and application information in the manufacturer datasheet when assigning PCB tracks, bypassing supply rails, and closing the loop around this amplifier.

Cotação Contato

LT1007MLB

LT1007MLB - Low-Noise Precision Op Amp | Texas Instruments

Texas Instruments LT1007MLB is a single-circuit, low-noise precision operational amplifier packaged in an 8-pin TO-99 metal-can package. The LT1007MLB is identified as a military-temperature-grade component with a through-hole, round-package construction and wire-form terminals. According to the manufacturer product page for the LT1007 family, the amplifier combines low-voltage noise with precision offset, drift, common-mode rejection, and power-supply rejection specifications. The family is specified with 10 µV offset voltage, 0.2 µV/°C offset drift, 130 dB common-mode rejection, and 130 dB power-supply rejection. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to increase the voltage level of a low-amplitude input. Its wider role within analog electronics includes closed-loop gain, active filtering, instrumentation, buffer amplification, and feedback control. The LT1007 family is positioned for applications where low input noise, input-offset accuracy, and low drift are more important than compactness or low power consumption. Noise performance is a principal benefit of the LT1007 family. The manufacturer specifies 2.5 nV/√Hz wideband input noise, a 2 Hz 1/f corner frequency, and 60 nV peak-to-peak noise over the 0.1 Hz to 10 Hz band. These characteristics make the amplifier suitable for precision signal-chain work in which the amplifier must preserve weak signals without adding excessive broadband or low-frequency noise. The device is a single amplifier rather than a multi-channel integrated package. The precision specifications further distinguish the LT1007 from general-purpose amplifiers. A 10 µV input-offset voltage and 0.2 µV/°C drift support stable operation when source impedance, temperature, or input common-mode conditions vary. The specified 130 dB common-mode rejection ratio reduces output movement caused by common-mode input voltage, while 130 dB power-supply rejection reduces sensitivity to supply ripple. These specifications are particularly useful in measurement and control systems that require accurate amplification of small differential signals. Typical uses include precision sensor interfaces, low-level instrumentation, strain-gauge and bridge-amplifier signal paths, high-resolution measurement equipment, low-noise filter stages, and laboratory analog systems. The TO-99-8 package favors legacy instrumentation, military-style equipment, and prototypes where a through-hole metal-can package is convenient. Its physical size and eight terminals make it more appropriate for through-hole designs than compact mixed-signal equipment. Designers should account for the metal-can package, required supply rails, input-common-mode range, output swing, stability, and compensation requirements when assigning the amplifier. The LT1007 is not decompensated; the 60 MHz gain-bandwidth statement in the manufacturer material applies to the related LT1037, not automatically to LT1007MLB. Follow the manufacturer pin-description table when making PCB connections and verify the exact operating limits for the grade and suffix. This product overview combines the exact LT1007MLB package and ordering information with the manufacturer’s family-level precision, noise, rejection, and supply specifications. It also distinguishes directly verified device facts from parameters that require confirmation from the complete LT1007 datasheet.

Cotação Contato

LT1007XH

LT1007XH - Low-Noise 200°C Op Amp in TO-5 | Analog Devices

Analog Devices LT1007XH is a single-circuit, low-noise operational amplifier specified for operation up to 200°C and supplied in a hermetic TO-5 package. It combines 10 µV offset voltage, 0.2 µV/°C offset drift, 130 dB common-mode rejection, and 130 dB power-supply rejection with monolithic noise performance of 2.5 nV/√Hz. The 1/f noise corner is 2 Hz, and 0.1 Hz-to-10 Hz noise is 60 nV peak-to-peak, making the device suitable for precision analog signal chains requiring low voltage noise and low drift. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, compare, or control analog signals. The LT1007 belongs to the precision operational-amplifier hierarchy, where low input noise, low offset drift, high rejection, and stable operation are more important than maximum bandwidth or minimum cost. Its wide operating-temperature capability extends that precision-focused role to industrial, instrumentation, and high-temperature analog systems. Key features include a 10 µV input offset voltage, 0.2 µV/°C input offset drift, and 130 dB common-mode rejection. The manufacturer describes a 2.5 nV/√Hz wideband noise density, a 2 Hz 1/f corner, and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. The manufacturer datasheet also states that these devices are 100% tested at 200°C ±3°C, with normal operating-temperature specifications provided separately for the LT1007M version. The LT1007 series was designed as a direct replacement for the OP-27 operational-amplifier family, as stated in the manufacturer datasheet. This heritage is important because it provides an established precision-amplifier upgrade path for existing instrumentation and signal-conditioning designs. The LT1007XH combines the series noise and precision characteristics with a hermetic TO-5 construction intended to support demanding thermal environments. Typical uses include precision instrumentation, low-level sensor amplification, bridge and strain-gauge signal conditioning, laboratory measurement equipment, and industrial analog front ends. Its low-noise and low-drift characteristics are particularly valuable when the input signal is small and the useful measurement must remain stable despite temperature changes. In these applications, the amplifier is usually placed directly in front of an ADC or downstream measurement chain. When designing with the LT1007XH, verify the exact LT1007XH electrical limits from the manufacturer datasheet rather than substituting the normal-temperature LT1007M limits. Decoupling, input-bias-current compensation, source impedance, output loading, and stability must be evaluated around the selected noise and gain conditions. The hermetic package also requires attention to lead strain, thermal expansion, and PCB soldering practices. This page combines verified manufacturer specifications, current distributor sourcing information, same-package drop-in candidates, and practical selection guidance. It also distinguishes the uniquely tested LT1007XH temperature grade from ordinary package-code or reel-code variants, helping engineers make a replacement decision based on electrical compatibility and environmental requirements.

Cotação Contato

LT1008CH

LT1008CH - Picoamp Precision Operational Amplifier | Analog Devices

The Analog Devices LT1008CH is a single-circuit precision operational amplifier in an 8-lead round TO-5 hermetic package, combining picoampere input bias current, microvolt-level offset voltage, low noise, and very high common-mode and power-supply rejection. It operates from dual supplies up to ±18 V and can deliver 5 mA of load current, making it suitable for instrumentation, precision measurement, low-level signal conditioning, and current-to-voltage conversion. An operational amplifier is a high-gain differential amplifier whose output responds to the voltage difference between its non-inverting and inverting inputs. Negative feedback causes the amplifier to amplify only the signal presented within its linear operating range while rejecting common-mode voltage and supply-noise variations. Within the broader hierarchy, the LT1008CH is an instrumentation amplifier, an operational amplifier, an analog amplifier, a semiconductor, and ultimately a linear integrated circuit. The LT1008 family's defining characteristic is input bias current maintained in the picoampere range over the full -55°C to 125°C temperature range. This behavior makes the device useful with high-impedance sources, charge-sensitive transducers, leakage-sensitive sensors, and precision bridges where conventional CMOS or bipolar amplifiers may introduce unacceptable input-current error. The microvolt offset specification and low drift support stable DC measurements, while low voltage noise and current noise improve the useful resolution of small-signal chains. Extremely high common-mode rejection ratio and power-supply rejection ratio allow the LT1008 to reject interference coupled from the input source or from imperfect power-supply rails. These characteristics matter in systems where the signal of interest is small but supply noise and ground offsets are much larger. The manufacturer describes the device as a universal precision operational amplifier suitable for practically all precision applications. Typical uses include precision strain-gauge and bridge amplifiers, low-current pH and ion-selective measurement front ends, photodiode and charge-sensitive preamplifiers, laboratory references, low-leakage buffer stages, and precision current-to-voltage converters. The 8-lead TO-5 construction is mechanically robust and suited to laboratory, industrial, and instrumentation systems where through-hole mounting and hermetic construction are preferred. When designing around the LT1008CH, account for input-bias-current error in the feedback network, provide adequate supply bypassing at the pins, and use guarding to minimize leakage on high-impedance nodes. Because the device can operate from ±18 V, verify the complete circuit's absolute maximum voltages and ensure input common-mode limits are respected during startup and fault conditions. This page consolidates manufacturer specifications, sourcing information, application guidance, and design notes that are not consolidated in a single distributor listing.

Cotação Contato

LT1010CH

LT1010CH - ±150mA Fast Power Buffer | Analog Devices

The Analog Devices LT1010CH is a fast, unity-gain power buffer designed to increase the output-current capability of existing integrated-circuit operational amplifiers by more than an order of magnitude. The device is specified for output current up to ±150mA and is supplied in the TO-39, 3-lead metal-can package identified by the CH suffix. Its primary role is to buffer a low-current op-amp output while preserving high speed and reducing sensitivity to capacitive loading. A power buffer is an analog amplifier stage used between a precision or high-impedance signal source and a load that requires substantially more output current than the source can supply. In the signal-chain hierarchy, the LT1010 is a power buffer amplifier, which is a specialized type of voltage-feedback operational-amplifier output stage. The unity-gain configuration makes the buffered output follow the driving op-amp voltage closely while adding drive capability rather than voltage gain. Key verified characteristics include a nominal 20 MHz bandwidth and ±150mA output-current capability. The TO-39 package is a round, 3-terminal metal-can package with wire-form leads. According to the manufacturer datasheet, the LT1010 is intended to increase the output capability of existing op amps by more than an order of magnitude. This makes it useful when driving heavier capacitive, resistive, or current-intensive analog loads while retaining a relatively simple external circuit. The LT1010 is particularly relevant to precision DC amplifiers, instrumentation, signal-conditioning systems, and laboratory or industrial analog designs. Its fast behavior can improve transient response and make the driving amplifier less sensitive to capacitive loading. Unlike a discrete complementary output stage, the integrated device also reduces thermal feedback inside precision amplifier designs, according to the Analog Devices datasheet. The CH package should be checked carefully against the manufacturer pinout before PCB assembly because the TO-39 lead assignment and metal-can orientation are essential to correct operation. The verified web data identifies the package as TO-39-3 and describes the device as a 1-circuit buffer amplifier. The manufacturer product page also lists the LT1010 family in 8-pin miniDIP, plastic TO-220, and 8-pin DFN packages, but the CH ordering code is the metal-can TO-39 variant. When using the LT1010CH, verify the output-current rating, supply voltage, thermal conditions, stability requirements, and maximum output-voltage swing against the specific application. The TO-39 package requires attention to thermal dissipation and soldering profile. Because the output stage can source and sink substantial current, the load return path, bypassing, and grounding should be arranged to prevent large transient currents from disturbing sensitive analog nodes. This page combines the verified manufacturer datasheet, distributor identification, package information, and application guidance with practical selection, thermal, and circuit-layout considerations. It also distinguishes the verified LT1010CH characteristics from parameters that require confirmation in the complete manufacturer datasheet.

Cotação Contato

LT1010CK

LT1010CK - Fast ±150mA Power Buffer | Analog Devices

The Analog Devices LT1010CK is a fast, unity-gain power buffer capable of sourcing or sinking ±150 mA and is supplied in a TO-3 package. It is designed to increase the output-current capability of existing integrated-circuit operational amplifiers by more than an order of magnitude. The LT1010CK is particularly useful when an amplifier must drive heavier loads while maintaining fast response and reduced sensitivity to capacitive loading. A power buffer is a specialized amplifier stage placed between a low-current operational amplifier and a load. Its role in the signal-chain hierarchy is broader than ordinary voltage amplification: the upstream op-amp establishes gain and signal accuracy, while the buffer provides current drive, isolation, and improved load behavior. The LT1010CK operates as a unity-gain buffer, so its nominal signal gain is 1. This arrangement is commonly used in precision DC amplifiers, instrumentation systems, signal-conditioning circuits, and applications requiring more output current than a conventional op-amp can provide. The key feature of the LT1010CK is its fast, bipolar power-buffer architecture with ±150 mA output capability. According to the manufacturer datasheet, the device can increase the output capability of an existing IC op-amp by more than an order of magnitude. Its unity-gain configuration also makes the buffer less sensitive to capacitive loading and helps reduce thermal feedback in precision DC amplifier circuits. The manufacturer identifies the product as being in production. The LT1010 family is offered in multiple package options, including an 8-pin miniDIP, plastic TO-220 and 8-pin DFN packages. The low thermal resistance of the power package is intended to assist in reducing operating junction temperatures, although the LT1010CK’s wider TO-3-style package requires careful attention to heat dissipation and lead clearance. The datasheet specifically identifies the device as a fast ±150 mA power buffer. Typical applications include boosting the drive of precision operational amplifiers, driving high-current feedback networks, buffering instrumentation signals, and supplying greater output current into downstream stages. It can also improve the behavior of fast amplifier systems when capacitive loads would otherwise disturb the upstream amplifier. Its combination of speed, current capability, and unity-gain isolation makes it useful in laboratory, industrial control, and signal-conditioning equipment. Designers should verify the exact pin functions, electrical limits, thermal conditions, and stability requirements against the manufacturer datasheet before implementation. A power buffer must be checked for DC power dissipation, output-current direction, source-to-sink transitions, and the voltage and temperature limits of every connected stage. Layout should minimize parasitic feedback paths and maintain adequate thermal spreading around the power package. This page combines the verified manufacturer product information, distributor availability references, package identification, pricing information, and engineering guidance in one concise design resource. It also distinguishes documented LT1010 family options from true drop-in replacements, avoiding unsupported substitute claims where verified pin-compatible alternatives are not available.

Cotação Contato

LT1011CH

LT1011CH - Low-Power Precision Comparator | Analog Devices

Analog Devices LT1011CH is a general-purpose voltage comparator with low offset voltage, low input bias current, and low supply-current demand, housed in an 8-pin TO-5 metal package. Its guaranteed maximum input offset voltage is 0.5 mV, maximum input bias current is 25 nA, maximum input offset current is 3 nA, and input offset-voltage drift is guaranteed at 15 uV/°C. The LT1011CH is also pin compatible with devices in the LM111 series, simplifying qualification of a second-source design. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LT1011 belongs to the comparator hierarchy within interface and signal-conditioning semiconductors. Unlike an operational amplifier used primarily for closed-loop amplification, a comparator is optimized for rapid, deterministic output transitions and is commonly used in threshold detection, sensing, and control systems. The LT1011's principal advantage over the LM111 reference family is its improved input behavior. According to the Analog Devices manufacturer datasheet, it offers four times lower bias current, six times lower offset voltage, and five times higher voltage gain than the LM111. It also adds a guaranteed 15 uV/°C offset-voltage drift specification and reduces supply current. These characteristics make the part useful when comparator accuracy, input loading, or temperature stability has more importance than absolute switching speed. The LT1011CH provides an open-collector output, allowing the output to pull a logic rail low while an external pull-up resistor establishes the high state. This architecture supports wired logic, level translation, and wired-AND functions, but it also requires a pull-up resistor and suitable rise-time control. Input common-mode range, supply voltage, response time, and output sink-current limits should be checked against the manufacturer datasheet for the exact operating conditions. Typical uses include precision threshold detection, window comparison, sensor conditioning, relay or actuator control, and low-current digital interfacing. The low 25 nA maximum input bias current is especially useful with high-impedance sensors, while the 0.5 mV maximum offset voltage supports comparisons where input-level differences are small. The pin-compatible relationship with the LM111 series also allows existing LM111-based boards to be evaluated for an upgrade. For reliable implementation, connect the open-collector output to a suitable pull-up resistor, place it close to the receiving logic input, and keep sensitive input traces away from switching nodes. Account for input offset and drift when defining the decision threshold, and verify that the output pull-up voltage, sink current, supply voltage, and input common-mode limits satisfy the application. The exact operating limits must be taken from the manufacturer datasheet. This page combines the LT1011CH device specifications, package information, verified manufacturer and distributor links, same-footprint alternatives, and practical comparator design guidance. It also identifies where a drop-in decision requires additional qualification, especially for temperature grade, input performance, output timing, and automotive or industrial system requirements.

Cotação Contato

LT1012CD

LT1012CD - Precision Op Amp, 25µV Offset, 8-SOIC | Texas Instruments

The Texas Instruments LT1012CD is a precision operational amplifier featuring 25 µV input offset voltage, 40 pA input bias current, and 200 µV typical offset in an 8-pin SOIC package. Originally designed by Linear Technology and now produced by Texas Instruments and authorized partners, the LT1012CD delivers picoampere-level bias currents over the full -55°C to +125°C temperature range with extremely high common-mode and power supply rejection ratios. A precision operational amplifier (op-amp) is a high-gain DC-coupled electronic voltage amplifier with a differential input and, usually, a single-ended output. Precision op-amps are characterized by low input offset voltage, low input bias current, low noise, and high common-mode rejection ratio (CMRR), making them suitable for amplifying small signals from sensors, transducers, and high-impedance sources. The LT1012 belongs to the broader category of linear integrated circuits and is positioned as a universal precision op-amp that combines the low-bias performance of BIFET/JFET-input amplifiers with the low-offset and low-drift characteristics of precision bipolar designs. Key features of the LT1012CD include 200 µV maximum input offset voltage, 40 pA maximum input bias current, 0.2 V/µs typical slew rate, and the ability to deliver 5 mA of output current while maintaining a voltage gain of one million. The device operates over a wide supply range (typically ±2 V to ±20 V) and offers extremely high CMRR and PSRR, with practically unmeasurable warm-up drift, making it ideal for precision instrumentation. The LT1012CD uses Linear Technology's advanced bipolar process technology that achieves sub-picoampere bias currents through active bias-current cancellation, while the precision bandgap-based input stage provides the low offset and low drift. The amplifier is internally compensated, eliminating the need for external compensation components in most applications, simplifying PCB layout and reducing BOM cost. Typical applications include precision thermocouple amplification, strain-gauge and weigh-scale signal conditioning, medical instrumentation, high-impedance sensor buffers, precision integrators for analog computation, and battery-powered portable instrumentation where the LT1012 achieves precision operation on two Ni-Cad batteries with only 1 mW of power dissipation. When designing with the LT1012CD, note that its 0.2 V/µs slew rate makes it suitable for DC and low-frequency signals but inadequate for high-speed or wide-bandwidth applications. For those applications, a faster op-amp such as the LT1028 or OP-27 should be considered. Standard 8-SOIC layout conventions apply, with input pins (IN+, IN-) at pins 3 and 2, output at pin 6, and power pins at pins 7 (V+) and 4 (V-). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet to support fast engineering decisions.

Cotação Contato

LT1012CH

LT1012CH - Picoamp Precision Op Amp | Analog Devices

Analog Devices LT1012CH is a single-circuit, internally compensated precision operational amplifier with picoampere input bias current, microvolt offset voltage, low voltage noise, low current noise, and very high input impedance. It operates from a single positive supply and can provide a closed-loop voltage gain of one million while delivering a 5 mA load current. The device is offered in an 8-lead round TO-5 metal-can package with wire-form leads. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LT1012 belongs to the precision operational-amplifier hierarchy, combining high open-loop gain with low offset, low bias current, and low-noise behavior. These characteristics make it useful when the source impedance can be high enough that input bias-current error would overwhelm a conventional amplifier. The LT1012's principal features include picoampere bias currents maintained across the full -55°C to +125°C temperature range, microvolt offset voltage, low offset drift with time and temperature, and exceptionally high common-mode and power-supply rejection ratios. According to the manufacturer, precision operation on two Ni-Cad batteries is possible with 1 mW of power dissipation. The reported 5 mA load-current capability and gain of one million are particularly useful for precision buffer, instrumentation, transducer, and low-level signal-chain applications. The LT1012 is implemented as a bipolar precision amplifier and is internally compensated for unity-gain stability. This architecture supports simple voltage-follower use without external compensation while retaining accurate low-frequency operation. The high gain and very low input current also make the device suitable for guarding, electrochemical measurement, photodiode amplification, and other applications where source leakage and offset can dominate measurement accuracy. Typical uses include precision sensor interfaces, low-current transducers, battery-powered instruments, pH and conductivity measurement circuits, photodiode amplifiers, and analog test equipment. The hermetic metal-can package provides a mechanically robust option for applications requiring stable operation over an extended temperature range, although engineers should observe the manufacturer's specified lead orientation and connection requirements. When using the LT1012CH, minimize leakage around the input pins and keep sensitive input traces away from power and ground paths. Because very high open-loop gain makes offset, bias-current error, and leakage especially important, clean PCB surfaces, guarded inputs, suitable bypassing, and careful source-impedance balancing are essential. This page combines verified manufacturer and distributor information with practical implementation guidance and clearly identified drop-in alternatives.

Cotação Contato

LT1013CD

LT1013CD - Dual Precision 1MHz Op Amp | Texas Instruments

The Texas Instruments LT1013CD is a low-power dual precision operational amplifier with a 4 V to 44 V supply range, 1 MHz gain-bandwidth product, 0.4 V/us slew rate, and two amplifiers in an 8-pin SOIC package. The device combines high gain, low noise, low supply current, and low-offset-voltage temperature coefficient in one circuit. According to the Texas Instruments product page, LT1013CD is the lead-free SOIC orderable version of the LT1013 family. An operational amplifier is an analog signal-processing semiconductor that uses high open-loop gain to amplify voltage differences accurately. Within the broader hierarchy, an operational amplifier is a linear amplifier, analog IC, and signal-conditioning component. The LT1013 fits precision instrumentation because its dual configuration supports common differential, summing, filtering, threshold, or transimpedance stages while reducing board area. Verified product information identifies high gain, low noise, low supply current, and a low-offset-voltage temperature coefficient as principal family characteristics. The device can operate from a single 5 V supply, has a common-mode input range that includes ground, and produces output swings to within a few millivolts of ground, as stated in the supplied comparison-source material. These properties are useful in battery-powered measurements where larger supply headroom would be inconvenient. The LT1013 family supports broad supply operation from 4 V to 44 V, allowing the same precision amplifier architecture to serve low-voltage instrumentation and higher-voltage industrial signal chains. Its 1 MHz gain-bandwidth product supports moderate-bandwidth closed-loop functions rather than high-speed waveform or communications applications. The 0.4 V/us slew rate likewise favors low-frequency precision conditioning over wideband pulse acquisition. Analog Devices lists battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, and active filters as representative LT1013 applications. These uses benefit from dual-channel operation, low supply current, precision behavior, and the ability to work across single and split supplies. When designing with the LT1013CD, preserve the required bypass capacitance, maintain common-mode and output headroom, and confirm that closed-loop bandwidth matches the 1 MHz family characteristic. Check noise, offset, supply current, and common-mode limits against the actual precision requirements. Pricing shown for LCSC is $0.4097 as of 2026-10-22; other distributor prices and current stock must be confirmed at purchase. This page combines verified manufacturer and distributor information, packaging details, applications, pricing context, and engineering guidance. It also identifies which parameters remain unavailable in the supplied evidence instead of estimating them, enabling engineers to make a more defensible LT1013CD selection.

Cotação Contato

LT1013CJG

LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments

The Texas Instruments LT1013CJG is a dual precision operational amplifier with 300 uV maximum input offset voltage, a 0.7 MHz gain-bandwidth product, and a hermetically sealed 8-pin ceramic DIP (CDIP-8) package with 0.300 inch lead pitch. Two amplifiers share one hermetic package, giving instrument-grade amplification in strain-gauge, thermocouple, and 4 mA to 20 mA current-loop signal chains. An operational amplifier (op amp) is a high-gain differential amplifier whose inverting and non-inverting inputs are compared, with feedback defining the closed-loop gain. A precision op amp is a variant optimised for low input offset voltage, low input bias current, and low drift so that small sensor signals are amplified without adding meaningful error. Within the component hierarchy, the LT1013CJG sits as a voltage-feedback amplifier in the family of amplifier ICs, inside the broader class of analog integrated circuits and power-management-adjacent signal-chain devices. Key specifications include a 300 uV maximum input offset voltage, 0.7 MHz gain-bandwidth product, and dual-amplifier configuration in a single hermetic ceramic DIP. The device operates from ±15 V supplies as well as from a single 5 V supply, and it exposes two offset-null pins so that input offset voltage can be trimmed in the circuit rather than accepted as a fixed error. Hermetic ceramic sealing protects the die from moisture and contaminants, which matters in high-reliability and legacy industrial equipment. Architecturally the LT1013CJG is a conventional bipolar voltage-feedback amplifier, which gives it wide supply-voltage swing, low input bias current, and predictable AC behaviour with a single compensation capacitor rather than the auto-zeroed architecture used in chopper-stabilised parts. The result is very low noise at low frequencies with continuous operation across the input range, at the cost of higher offsets than modern auto-zeroed amplifiers. Typical applications include bridge and strain-gauge signal conditioners, thermocouple amplifiers, precision instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multi-stage gain blocks in battery-powered precision instruments. When designing around this device, use the two offset-null pins for trimming and place the compensation capacitor close to the device. Keep the hermetic package away from thermal sources, because gradient across the ceramic can shift offset voltage, and avoid saturating the output near the supply rails in instrumentation front ends. This page combines manufacturer and distributor technical data, drop-in alternatives, comparison parameters, and practical design guidance that are not consolidated in the original datasheet.

Cotação Contato

LT1013CP

LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments

The Texas Instruments LT1013CP is a dual precision operational amplifier featuring high gain, low supply current, low noise, and a low offset-voltage temperature coefficient, supplied in an 8-pin PDIP (P) package. It operates from a single 4V to 44V supply (or dual ±2V to ±22V supplies), draws only 0.5 mA typical supply current per amplifier, and delivers 150 µV maximum input offset voltage at 25°C (LT1013A grade). The input common-mode range includes ground and the output swings to within a few millivolts of ground while sinking current, eliminating crossover distortion. A dual precision op amp is a two-channel integrated operational amplifier that combines matched transistor pairs and laser-trimmed thin-film resistors to achieve DC accuracy comparable to chopper-stabilized designs while consuming milliwatts of power. Within the broader component taxonomy, dual op amps sit under operational amplifiers -> amplifiers -> analog ICs -> semiconductor. The LT1013 was the first precision dual op amp in the 8-pin industry-standard pinout, upgrading legacy devices such as the MC1458/MC1558, LM158, and OP-221 with significantly lower noise and better DC stability. Key features include 150 µV max input offset voltage (LT1013A) with 2.5 µV/°C max offset voltage temperature coefficient, 0.5 mA typical supply current per amplifier, single-supply operation from 4V to 44V, ground-sensing input range, and output swing to within millivolts of ground. The NPN input stage delivers low input bias current and low voltage noise density suitable for transducer and instrumentation front-ends. Typical applications include battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, 4 mA to 20 mA current-loop transmitters, active filters, multiple limit threshold detection, and instrumentation amplifier building blocks. The wide supply range and ground-sensing inputs make it ideal for single-supply industrial and process-control systems. When designing with this part, observe the input common-mode limit: although the inputs include ground, the upper common-mode limit is approximately 1.5V below the positive rail. Place a 0.1 µF bypass capacitor close to the supply pin and add a 10 µF bulk capacitor on the supply rail to maintain low-impedance power across the LT1013's full bandwidth.

Cotação Contato

LT1013DD

LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments

The Texas Instruments LT1013DD is a low-power dual precision operational amplifier with a 5 V to 44 V wide supply range, two amplifier channels, and an 8-pin SOIC (D) package. The device is intended for instrumentation, signal-conditioning, filtering, and threshold-detection circuits that operate from low single-supply voltages through substantially higher industrial supply levels. Its precision-oriented design combines high gain, low supply current, low noise, and low offset-voltage temperature coefficient, while the extended supply range supports both single-supply and dual-supply implementations. An operational amplifier is an active analog signal-processing device that uses feedback to amplify the difference between its inverting and non-inverting inputs. The dual LT1013 provides two amplifiers in one package, allowing designers to implement two signal paths without using separate packages. In the broader semiconductor hierarchy, the LT1013DD is an analog integrated circuit, specifically a precision operational amplifier used within instrumentation and embedded signal-conditioning systems. The verified product information identifies the LT1013DD as a standard general-purpose dual amplifier with an 8-SOIC package and a 0 °C to 70 °C operating-temperature range. The TI product-page snippet describes the LT1013D as a low-power device with a 5 V to 44 V wide supply range. The wider LT1013 product page states a 4 V to 44 V supply range, so the exact minimum operating supply for the selected LT1013DD ordering option should be confirmed against the manufacturer datasheet before design release. The LT1013DD is suited to battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA-to-20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multiple gain blocks. Its dual-channel configuration is useful where two related signals must be conditioned consistently, such as sensor excitation and monitoring or differential and common-reference measurements. Designers should pay particular attention to the SOIC-8 pin mapping, supply bypass capacitors, input common-mode range, output swing, and the operating-temperature limits for this ordering code. The precision characteristics make the device useful for instrumentation, but they do not make it a universal rail-to-rail amplifier. Verify signal levels, noise requirements, load conditions, and stability requirements against the manufacturer datasheet rather than assuming that a substitute is electrically identical. This product page consolidates the verified manufacturer and distributor information, source-backed alternatives, package details, pricing fields, application guidance, and design notes. It is intended to support initial component selection and comparison rather than replace the complete LT1013D datasheet during sign-off.

Cotação Contato

Subcategorias

Produtos (39.000+)

LSF0101 - 1-Bit Auto-Bidirectional Level Translator | Texas Instruments

LSF0102-Q1 - 2-Ch Auto Bidirectional Level Translator | TI

LSF0102DDFR - 2-Ch 100Mbps Level Translator | TI

LSF0108PWR - 8-Ch Bidirectional Level Translator | TI

LSF0108QPWRQ1 - Auto 8-Ch Bidirectional Level Shifter | TI

LSF0204RUTR - 4-Bit Bidirectional Level Translator | Texas Instruments

LT1001CD - Precision Op-Amp 8-SOIC | Texas Instruments

LT1001CDR - Precision Op-Amp 8-SOIC | Texas Instruments (Tape & Reel)

LT1001CH - 110dB Precision Operational Amplifier | Analog Devices

LT1001CP - 110uV Offset, 0.8MHz Precision Op Amp | TI

LT1007CH - Low-Noise Precision Op Amp | Analog Devices

LT1007CJG - Low-Noise Precision Op Amp | Texas Instruments

LT1007MLB - Low-Noise Precision Op Amp | Texas Instruments

LT1007XH - Low-Noise 200°C Op Amp in TO-5 | Analog Devices

LT1008CH - Picoamp Precision Operational Amplifier | Analog Devices

LT1010CH - ±150mA Fast Power Buffer | Analog Devices

LT1010CK - Fast ±150mA Power Buffer | Analog Devices

LT1011CH - Low-Power Precision Comparator | Analog Devices

LT1012CD - Precision Op Amp, 25µV Offset, 8-SOIC | Texas Instruments

LT1012CH - Picoamp Precision Op Amp | Analog Devices

LT1013CD - Dual Precision 1MHz Op Amp | Texas Instruments

LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments

LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments

LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments