Microcontroladores

Produtos (18712)

ATSAMD20J14A-AU - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip
ATSAMD20J14A-AU

ATSAMD20J14A-AU - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip

The Microchip Technology (formerly Atmel) ATSAMD20J14A-AU is a 32-bit ARM Cortex-M0+ microcontroller with 16KB of Flash and 2KB of SRAM, housed in a 64-pin LQFP (10x10 mm) package. It operates at up to 48 MHz from a 1.62V to 3.6V supply and includes a 12-bit ADC, 10-bit DAC, and the SAM D20 series peripheral set including SERCOM, TC, and EVENT system. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as ADCs, timers, and communication interfaces. Within the broader hierarchy, this part is a Cortex-M0+ based microcontroller -> ARM-based MCU -> 32-bit microcontroller -> embedded controller -> semiconductor IC. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for deterministic real-time performance at very low active and sleep currents, making it a fit for battery-powered and cost-sensitive embedded designs. Key features include 16KB Flash / 2KB SRAM, six SERCOM modules that can each be configured as USART, I2C, or SPI, up to 48 MHz core clock, a 12-bit 350 ksps ADC with up to 14 channels, and a 10-bit 350 ksps DAC. The device supports both 1.62V to 3.6V single-supply operation and features the Microchip Event System for inter-peripheral signaling without CPU intervention. The ATSAMD20J14A-AU uses a two-stage pipelined Cortex-M0+ core with single-cycle I/O access through the AHB/APB bridge matrix, single-cycle multiplier, and a low-power SleepWalking peripheral architecture that lets SERCOM, TC, and ADC run autonomously while the CPU sleeps, reducing system-level power. Typical applications include IoT sensor nodes, consumer electronics HMI subsystems, industrial control peripherals, USB HID bridges (with on-chip pull-ups), and home automation controllers. In each case the part provides deterministic Cortex-M0+ compute plus SERCOM-based connectivity without requiring an external PHY. When designing with this part, reserve pin 1 (VDDIO) and pin 34 (VDDIN) decoupling with at least 100nF X7R capacitors placed within 2 mm of each pin, and ensure the NRST pull-up is at least 10 kohm to guarantee a clean power-on reset. This page consolidates distributor pricing, drop-in alternatives from the same SAM D20 family, and practical design notes not collected on a single distributor listing.

Cotação Contato
ATSAMD20J14A-AUT - 48MHz Cortex-M0+ MCU 16KB Flash LQFP-64
ATSAMD20J14A-AUT

ATSAMD20J14A-AUT - 48MHz Cortex-M0+ MCU 16KB Flash LQFP-64

The Microchip Technology ATSAMD20J14A-AUT is an ARM Cortex-M0+ based 32-bit microcontroller from the SAM D20J family, delivering up to 48 MHz CPU performance with 16 KB of Flash and 2 KB of SRAM in a 64-pin LQFP package (10x10 mm). It is designed for low-power, high-performance embedded applications spanning home automation, consumer electronics, metering, and industrial control. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (timers, ADC, communication interfaces, GPIO). Within the broader taxonomy, the ATSAMD20J14A belongs to the ARM Cortex-M0+ class of microcontrollers, which targets ultra-low-power and cost-sensitive applications while retaining the ARM Thumb instruction set. The Cortex-M0+ sits at the entry point of the Cortex-M family (M0/M0+ -> M3/M4 -> M7), trading DSP and FPU capability for the smallest die area and lowest active/idle power. Key specifications include a 48 MHz maximum CPU clock, 16 KB Flash program memory, 2 KB SRAM, an 8-channel 12-bit ADC, two I2C, up to six SERCOM (configurable serial), six 16-bit timers, and a 12-channel Event System. The device operates from 1.62 V to 3.63 V, supports Sleep, Idle, and Standby modes with full RAM retention, and features an integrated 32 kHz RTC with calendar mode. Typical applications include battery-powered sensor nodes, HVAC controllers, smart thermostats, low-end wireless gateways (when paired with an external radio), industrial HMI panels, and portable medical accessories. The Cortex-M0+ core provides deterministic interrupt latency suitable for hard-real-time control loops, while the rich SERCOM peripheral set simplifies protocol bridging between I2C sensors, SPI flash, and UART modems. When designing with this part, take care to populate the decoupling network with at least one 100 nF X7R capacitor per VDD pin plus a bulk 4.7 uF tantalum or ceramic capacitor. The brown-out detector and WDT must be configured in firmware; default POR settings do not enable them. The 64-LQFP package allows hand-solderable prototyping as well as high-density SMT assembly. This page synthesizes distributor pricing, pin-compatible drop-in alternates within the SAM D20 family, and practical design notes that go beyond the manufacturer datasheet's basic block diagram to give working engineers decision-ready guidance.

Cotação Contato
ATSAMD20J14A-CNT - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip
ATSAMD20J14A-CNT

ATSAMD20J14A-CNT - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip

The Microchip Technology ATSAMD20J14A-CNT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20J family, running at up to 48 MHz with 16 KB of flash and 2 KB of SRAM, housed in a 64-ball UFBGA (5x5 mm) package. It is a low-power, high-performance device targeting home automation, consumer, metering, and industrial applications. An ARM Cortex-M0+ microcontroller is one of the smallest, most energy-efficient 32-bit processor cores in the ARM Cortex family, designed for deeply embedded applications that need deterministic real-time behaviour, low active power, and deep-sleep currents in the microamp range. The Cortex-M0+ integrates the NVIC, SysTick, Wake-up Interrupt Controller, and optional single-cycle I/O, and it sits in a hierarchy of microcontroller -> 32-bit MCU -> ARM Cortex-M family -> embedded controller. The SAM D20J family from Microchip/Atmel adds Atmel/Microchip proprietary peripherals on top of this core. Key features of the ATSAMD20J14A-CNT include 16 KB (16K x 8) flash program memory, 2 KB SRAM, an integrated 12-bit ADC, multiple SERCOM (Serial Communication Interface) modules configurable as UART/SPI/I2C, up to 52 I/O pins, and a 1.6-3.6 V operating range. The device supports industrial temperature range up to 105C and is supplied in a green, RoHS-compliant 64-UFBGA package. The architecture uses single-cycle hardware multiply, a Microchip/Atmel event system for inter-peripheral signalling without CPU intervention, and the SleepWalking peripheral that can wake the CPU based on peripheral events. Together with the Cortex-M0+ core these features deliver higher deterministic performance per MHz than legacy 8-bit/16-bit MCUs while staying within tight power budgets. Typical applications include home automation nodes, smart metering endpoints, consumer electronics HMI, low-cost sensor hubs, and industrial control blocks where deterministic 32-bit performance and tiny BGA footprint are both required. Industrial-grade temperature range and wide supply range support deployment in harsh electrical environments. When designing, ensure the UFBGA land pattern matches Microchip's reference layout and respect the 1.6-3.6 V supply range; an external reset supervisor is recommended if the host rail is not monotonically stable at power-up. Programming and debugging are handled via the SWD interface using Microchip's Atmel Studio / MPLAB X toolchain. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Cotação Contato
ATSAMD20J14A-CU - ARM Cortex-M0+ 48MHz 16KB MCU | Microchip
ATSAMD20J14A-CU

ATSAMD20J14A-CU - ARM Cortex-M0+ 48MHz 16KB MCU | Microchip

The Microchip Technology ATSAMD20J14A-CU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, integrating 16KB of Flash and 2KB of SRAM, and operating at up to 48 MHz in a 64-ball UFBGA (5x5 mm) package. It operates across a wide 1.62V to 3.63V supply range with on-chip DC-DC and LDO regulators that simplify single-rail designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the Cortex-M family, designed for deterministic real-time embedded tasks. The SAM D20 family (D20J = 64-pin/pad variant) sits within Microchip's 32-bit MCU portfolio above the 8-bit AVR and below the Cortex-M4 SAM D5x/SAM E5x lines, making it a mainstream general-purpose 32-bit MCU. The ATSAMD20J14A-CU features the Cortex-M0+ core with single-cycle I/O access, hardware divide, and a Nested Vectored Interrupt Controller (NVIC) for low-latency interrupt handling. Up to six Serial Communication Interfaces (SERCOM, each configurable as USART, SPI, or I2C), up to two I2S channels, a 12-bit 350 ksps ADC with up to 14 channels, a 10-bit DAC, and a 32-bit RTC round out the peripheral set. Internal 8 MHz and 32 kHz oscillators plus a fractional PLL reduce external component count, while the Full-Speed USB 2.0 device and Host with on-chip transceiver (where present in the family) simplifies connectivity. Low-power operation is central to the design: Idle, Standby, Backup, and Off sleep modes draw microamps or less, making the part attractive for battery-powered and energy-harvesting applications. The integrated Event System allows peripherals to communicate without CPU wake-up, freeing the core for power-down. Typical applications include home automation nodes, smart metering, consumer appliances, industrial sensor hubs, USB human-interface devices (HID), and low-power IoT endpoints. In these scenarios, the 16KB Flash / 2KB SRAM footprint fits small protocol stacks such as BLE beacons (with external radio), Modbus/RTU bridges, or LoRaWAN device firmware, while the SERCOMs and ADC handle sensor interfacing. The wide 1.62V-3.63V range lets the same part run from a single Li-ion cell or 3.3V regulated bus. When designing with the ATSAMD20J14A-CU, plan for the UFBGA-64 footprint using a 0.5 mm or finer pitch PCB process and ensure the exposed paddle under the BGA is properly soldered for thermal and electrical performance. Designers familiar with the SAM D20 family will benefit from Microchip's Atmel Studio / MPLAB X toolchain, ASF (Advanced Software Framework), and free Atmel START configuration. This page synthesizes distributor stock and pricing, same-family alternatives, and practical design notes for the ATSAMD20J14A-CU - information not consolidated in the manufacturer datasheet alone.

Cotação Contato
ATSAMD20J14A-CUT - SAM D20 32-bit ARM Cortex-M0+ MCU, 16KB Flash | Microchip
ATSAMD20J14A-CUT

ATSAMD20J14A-CUT - SAM D20 32-bit ARM Cortex-M0+ MCU, 16KB Flash | Microchip

The Microchip ATSAMD20J14A-CUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20 family, featuring 16 KB Flash, 2 KB SRAM, and a 48 MHz CPU in a 64-ball UFBGA (5x5 mm) package. The "CUT" suffix denotes the industrial temperature grade (-40C to +85C), green/RoHS-compliant, tape-and-reel packaging variant. Operating voltage spans 1.62 V to 3.63 V, allowing direct connection to 1.8 V, 2.5 V, and 3.3 V rails common in IoT and consumer designs. An ARM Cortex-M0+ microcontroller is the smallest, most energy-efficient member of the ARM Cortex-M family, combining a Thumb-2 instruction set with a single-cycle multiplier and NVIC interrupt controller. The ATSAMD20J14A sits inside the broader microcontrollers (MCU) product category, which falls under integrated circuits (ICs) and ultimately semiconductors in the taxonomy hierarchy. Cortex-M0+ cores are widely chosen for battery-powered and cost-sensitive applications because they deliver 32-bit performance at power levels comparable to 8-bit MCUs. Key features include the Cortex-M0+ core with single-cycle hardware multiply, 16 KB self-programmable Flash, 2 KB SRAM, and the Microchip Event System for inter-peripheral signaling without CPU intervention. The peripheral set comprises up to 52 programmable I/O pins, SERCOM (configurable serial communication) channels, a 12-bit 350 kS/s ADC, a 10-bit DAC, four 16-bit Timer/Counters, and a Real-Time Clock. Full-speed USB 2.0 device support and a Peripheral Touch Controller (PTC) for capacitive touch are integrated on most SAM D20J devices, though exact peripheral count on the J14 die is device-specific. The device leverages Microchip's proprietary Atmel/Microchip low-power design, providing multiple Sleep modes (IDLE, STANDBY, BACKUP) with current consumption down to the low microamp range, suitable for battery-powered end nodes. The integrated Sleepwalking peripheral Event System allows peripherals to wake the CPU only when meaningful events occur, dramatically reducing average power in sensor applications. The Cortex-M0+ pipeline keeps deterministic interrupt latency. Typical applications include IoT sensor nodes, wearable fitness bands, BLE/Bluetooth proximity beacons, low-cost industrial sensor hubs, and consumer Human Interface Devices (HID) such as keyboards and remote controls. The PTC enables touch button or slider interfaces for white goods and consumer appliances. The compact 5x5 mm UFBGA footprint suits space-constrained designs where PCB area is at a premium. When designing with this MCU, allocate decoupling capacitors (100 nF + 1 uF) close to each VDD pin and follow Microchip's recommended DFM layout for the UFBGA escape pattern. Consider ATSAMD20J14A-CNT or ATSAMD20J14A-AUT if a different operating temperature grade or pin-package combination is required; these are pin-to-pin compatible with the CUT variant for design reuse.

Cotação Contato
ATSAMD20J14A-MNT - 48MHz Cortex-M0+ 16KB Flash MCU | Microchip
ATSAMD20J14A-MNT

ATSAMD20J14A-MNT - 48MHz Cortex-M0+ 16KB Flash MCU | Microchip

The Microchip Technology ATSAMD20J14A-MNT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, operating at up to 48 MHz with 16KB of Flash and 2KB of SRAM in a 64-pin QFN (9x9 mm) package. The -MNT suffix denotes tape-and-reel packaging and industrial temperature grade support up to +105 C junction. The device operates from a 1.6 V to 3.6 V supply, reaching 2.14 CoreMark/MHz, and integrates a 6-channel SERCOM for flexible I2C/SPI/UART configuration along with a 12-bit ADC, 10-bit DAC, and multiple timer/counter blocks. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals into one package. ARM Cortex-M0+ cores are the smallest and most energy-efficient members of the Cortex-M family, intended for deterministic real-time embedded control. The SAM D20J family lies within the broader Atmel SMART lineup of Cortex-M microcontrollers, designed for low-power IoT, consumer, and industrial applications where ARM ecosystem compatibility and ultra-low standby current matter. Key features of the ATSAMD20J14A-MNT include its Cortex-M0+ core with single-cycle I/O access, a built-in 32 kHz internal oscillator and 8 MHz to 48 MHz DFLL for clocking flexibility, an event system for inter-peripheral signaling without CPU intervention, and the SAM D20's signature SleepWalking peripheral operation that lets ADCs and SERCOMs run while the CPU is stopped. The part offers 14 SERCOM instances in the 64-pin SAM D20J variants, six of which are bonded out on this package. Designers benefit from Microchip's MPLAB X IDE support, the Harmony 3 framework, and the SAMD20/21 family pin compatibility, which simplifies migration within the portfolio. The QFN package's exposed thermal pad and 9x9 mm footprint enable compact layouts with good thermal dissipation for motor control, sensor hubs, and battery-powered products. Typical applications include IoT sensor nodes, BLE/Wi-Fi co-processor hosts, USB device controllers (with on-chip USB on related parts), industrial sensor interfaces, low-power wearables, and home automation controllers. Engineers also use it as a pin-compatible scaling option when projects move between the SAM D20E (32-pin) and SAM D20G (48-pin) versions within the same family. Design consideration: the ATSAMD20J14A-MNT has only 16KB Flash, which constrains the choice of TCP/IP stacks and Bluetooth libraries. For complex code bases consider ATSAMD20J18A-MNT (256KB) or ATSAMD20G18A-MU. Always include a 1 uF decoupling capacitor on VDD and a 10 nHF on the analog supply AVDD, and follow the reference schematic in the Atmel SMART SAM D20 datasheet to avoid POR and brownout issues. This page synthesizes distributor pricing, drop-in pin-compatible variants, and application notes not found in the bare datasheet, providing a single-point engineering reference for the ATSAMD20J14A-MNT and its place in the Microchip SAM D20 family.

Cotação Contato
ATSAMD20J14A-MU - ARM Cortex-M0+ MCU 48MHz 16KB Flash | Microchip
ATSAMD20J14A-MU

ATSAMD20J14A-MU - ARM Cortex-M0+ MCU 48MHz 16KB Flash | Microchip

The Microchip Technology ATSAMD20J14A-MU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, running up to 48 MHz and integrating 16 KB Flash and 2 KB SRAM in a 64-pin QFN (9x9 mm) package. It is part of the Atmel | SMART SAM D20 low-power MCU series that delivers 2.14 CoreMark/MHz performance and ranges from 32 to 64 pins with up to 256 KB Flash and 32 KB SRAM across the family. An ARM Cortex-M0+ MCU is a 32-bit reduced instruction set computing (RISC) microcontroller core designed by ARM Holdings for low-power embedded applications. The Cortex-M0+ sits within the broader ARM Cortex-M processor family, which in turn belongs to the microcontroller (MCU) category of integrated circuits under the semiconductor hierarchy. Compared with 8-bit MCUs, Cortex-M0+ devices offer higher code density, faster interrupt handling, and a Thumb-2 instruction subset while retaining low active and sleep current. The SAM D20 family targets simple migration with identical peripheral modules, hex-compatible code, a linear address map, and pin-compatible footprints across 32-, 48-, and 64-pin options. Key features include a maximum CPU clock of 48 MHz, 16 KB embedded Flash, 2 KB SRAM, 1.8V/2.5V/3.3V operating voltage support, and a full Cortex-M0+ NVIC with up to 52 maskable interrupts. Integrated peripherals include SERCOM (configurable USART, SPI, I2C), 12-bit ADC, 10-bit DAC, timers, RTC, and event system. The 64-QFN package with exposed pad provides low thermal resistance for the small die, enabling compact designs without an external heatsink at typical embedded current draws. Typical applications include IoT sensor nodes, battery-powered wearables, consumer electronics human-machine interfaces, low-power wireless sensor platforms, USB device controllers, and industrial control front-ends. The event system and sleepwalking peripherals enable microamp-range sleep currents while still responding to asynchronous I/O events. When designing with the SAM D20J, engineers should size the decoupling network per the datasheet and follow Microchip's Atmel Studio / MPLAB X reference designs for the configured peripherals. The 64-pin QFN with exposed pad requires thermal via stitching under the EP for production reliability.

Cotação Contato
ATSAMD20J14A-MUT - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip
ATSAMD20J14A-MUT

ATSAMD20J14A-MUT - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip

The Microchip Technology ATSAMD20J14A-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, featuring 16KB of Flash, 2KB of SRAM, and a 48MHz maximum CPU clock, housed in a 64-pin QFN (9x9 mm) package with exposed thermal pad. The 'MUT' suffix denotes tape-and-reel packaging and industrial temperature grade (-40C to +85C). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals into one device. ARM Cortex-M0+ cores are the smallest and most energy-efficient members of the ARM Cortex-M family, optimized for deterministic embedded control in cost-sensitive applications. The SAM D20J sits within Microchip's broader portfolio: ARM Cortex-M0+ MCU -> SAM D family -> SAM D20J series -> low-power 32-bit microcontroller -> embedded processor -> semiconductor. Key features of the ATSAMD20J14A-MUT include the Cortex-M0+ core achieving 2.14 CoreMark/MHz, an integrated Serial Communication Interface (SERCOM) block providing flexible UART/SPI/I2C configuration, a 12-bit ADC up to 350ksps, and multiple sleep modes with sub-microamp standby current. The 64-QFN package includes an exposed pad that must be soldered to the PCB ground plane for proper thermal and electrical performance. The ATSAMD20J14A-MUT is typically used as the main controller in IoT sensor nodes, low-power wireless gateways, industrial sensor interfaces, USB human-interface devices, and consumer electronics where a balance of processing performance, low power consumption, and small footprint is required. The device is supported by Microchip's MPLAB X IDE, Atmel Studio 7, and the ASF (Atmel Software Framework) library for rapid development. When designing with this MCU, ensure the exposed pad is soldered to a continuous ground plane to achieve the rated 64-QFN thermal resistance. Decoupling capacitors must be placed within 2mm of each VDD pin pair to maintain ADC accuracy at high sampling rates, and unused I/O pins should be configured as outputs or inputs with internal pull-up to minimize leakage current in sleep modes. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes not consolidated on the manufacturer datasheet alone, helping engineers select and source the ATSAMD20J14A-MUT with confidence.

Cotação Contato
ATSAMD20J14B-AU - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip
ATSAMD20J14B-AU

ATSAMD20J14B-AU - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip

The Microchip Technology ATSAMD20J14B-AU is a 32-bit ARM Cortex-M0+ microcontroller running at 48 MHz with 16 KB of Flash and 2 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package with industrial temperature rating (-40C to +85C). It operates from 1.62 V to 3.63 V and integrates a peripheral touch controller, 6 SERCOM interfaces, a 12-bit ADC, 10-bit DAC, and a full-speed USB 2.0 device. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripheral interfaces into one package. MCUs form the lowest tier of embedded computing, sitting below microprocessors and above simple logic ICs in the system-on-chip hierarchy. Within the Cortex family, M0+ is the smallest, lowest-power ARM core; it targets deterministic, energy-efficient real-time tasks such as sensor fusion, motor timing, and human-machine interface (HMI) glue logic. The SAM D20 family was Microchip's first Cortex-M0+ entry and remains popular for cost-sensitive, low-power designs. Key features include 6 configurable SERCOM channels (each usable as UART, SPI, or I2C), a 12-channel 350 ksps 12-bit ADC, a 10-bit 350 ksps DAC, two analog comparators, a 24-bit RTC, and full-speed USB 2.0 device with on-chip transceiver. The device includes 38 GPIO, the Peripheral Touch Controller (PTC) supporting buttons, sliders, and wheels, and supports Sleep, Idle, and Standby modes consuming less than 5 uA in Standby. The ATSAMD20J14B-AU uses a single-cycle hardware multiplier, a nested vector interrupt controller (NVIC) with 32 channels, and Microchip's Event System for inter-peripheral signalling without CPU wake-up. The integrated USB 2.0 Full-Speed device, 1 KB endpoint RAM, and on-chip pull-ups eliminate external PHY components, reducing BOM and board area. The 1.62 V minimum supply allows single-cell Li-ion or 2x AA alkaline operation. Typical applications include home automation nodes, smart metering endpoints, consumer HMI, industrial sensor interfaces, and USB HID peripherals. The PTC and DAC combination also makes the part well-suited to capacitive touch panels and small audio-tone generators. For wireless sensor nodes, the low-power Sleep modes combined with the RTC enable multi-year battery life on coin cells. When designing with this MCU, ensure the 64-TQFP footprint is selected for the 'J' (64-pin) variant - the 48-pin 'G' and 32-pin 'E' variants differ in pinout and peripheral count. Decouple VDDIN, VDDIO, and VDDCORE each with at least 100 nF plus 4.7 uF bulk, and tie the exposed pad (if present) to a solid ground pour for thermal relief. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes not found in the bare datasheet, giving engineers a single decision-ready reference.

Cotação Contato
ATSAMD20J14B-MU - 48MHz Cortex-M0+ MCU 16KB Flash 64-VQFN | Microchip
ATSAMD20J14B-MU

ATSAMD20J14B-MU - 48MHz Cortex-M0+ MCU 16KB Flash 64-VQFN | Microchip

The Microchip Technology ATSAMD20J14B-MU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20J family, operating at up to 48 MHz and integrating 16 KB of Flash program memory and 2 KB of SRAM in a 64-pin VQFN (9x9 mm) package with exposed thermal pad. It supports an operating voltage range of 1.62V to 3.6V and offers up to 52 general-purpose I/O pins with peripheral touch support, making it suitable for mixed-signal embedded designs. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (timers, communication interfaces, ADCs) into a single chip. The Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M processor family, designed for deterministic real-time control and ultra-low-power embedded applications. Within the broader hierarchy, the SAM D20 belongs to the 32-bit microcontroller class, which sits above 8/16-bit MCUs and below application processors in capability and power consumption. Key features include the Cortex-M0+ core with single-cycle I/O access, an 8-channel 12-bit ADC capable of up to 350 ksps, two I2C, up to six SERCOM (configurable serial communication) modules, a 24-bit timer/counter, and the Peripheral Touch Controller (PTC) for capacitive touch sensing. The device consumes less than 70 uA/MHz in active mode and supports multiple low-power sleep modes, enabling battery-powered designs that must extend operating life. From an architectural standpoint, the SAM D20 uses a Harvard-style bus matrix connecting the Cortex-M0+ core to Flash, SRAM, and the AHB/APB peripheral fabric. The integrated PTC hardware block supports capacitive touch sensing with up to 256 buttons, reducing BOM cost and MCU cycles for touch user-interface designs. The wide 1.62V-3.6V supply range simplifies designs powered by 2x AA cells or Li-ion batteries without external level shifters. Typical applications include home automation controllers, low-power IoT sensor nodes, consumer electronics with capacitive touch buttons, industrial metering (gas/water/electricity), battery-powered portable devices, and LED lighting control. The combination of low power, ample I/O, and integrated touch makes the ATSAMD20J14B-MU a strong fit for cost-sensitive user-interface products. When designing with this part, allocate adequate Flash for the bootloader (typically 4 KB for SAM-BA) plus application code, and reserve a portion of SRAM for the Atmel/Microchip Software Framework (ASF) drivers. Use the exposed pad as the primary ground and thermal dissipation path, and follow the manufacturer PCB layout guidelines for QFN packages to ensure reliable reflow soldering. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the ATSAMD20J14B-MU drawn from the Microchip datasheet and live distributor inventory data, information typically scattered across manufacturer PDFs and distributor listings.

Cotação Contato
ATSAMD20J15A-AN - 32KB Flash Cortex-M0+ MCU 48MHz | Microchip
ATSAMD20J15A-AN

ATSAMD20J15A-AN - 32KB Flash Cortex-M0+ MCU 48MHz | Microchip

The Microchip Technology ATSAMD20J15A-AN is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, integrating 32KB of Flash and 4KB of SRAM with a maximum CPU clock of 48MHz, packaged in a 64-pin TQFP (10x10 mm) with an exposed pad. It is offered in an industrial-grade -40C to +105C operating range, supports 1.62V-3.63V single-supply operation, and exposes 52 general-purpose I/O lines through multiple serial interfaces including I2C, SPI, and UART/USART. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, peripherals, and I/O on a single silicon die, enabling embedded control without external logic. The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, designed for deterministic real-time workloads at very low active and sleep currents; the ATSAMD20J15A-AN positions itself in the broad hierarchy: ARM Cortex-M0+ -> 32-bit MCU -> microcontroller -> semiconductor device. Key features include a 2.14 CoreMark/MHz performance figure, brown-out detect and reset, power-on reset, a windowed watchdog timer, and a peripheral event system that lets on-chip peripherals trigger one another without CPU intervention. The device also integrates a full-speed USB 2.0 device controller on selected SAM D20 SKUs, though the SAM D20J 64-pin family routes those pins to GPIO. Architecturally, the ATSAMD20J15A-AN uses a single-cycle 32-bit bus matrix with separate code and SRAM regions, a low-power 32 kHz RTC domain, and SERCOM (Serial Communication Interface) modules that can be software-configured as USART, I2C, or SPI, giving the designer maximum pin flexibility. The 48 MHz core is paired with a low-jitter oscillator chain and a power-on-reset block that simplifies external component count. Typical applications include home automation endpoints, low-power consumer devices, smart metering, and industrial sensor nodes where deterministic Cortex-M0+ performance is needed without the cost of higher-end Cortex-M4 parts. The wide 1.62V-3.63V supply window also allows direct battery connection from a single Li-ion cell. When designing with this device, prefer Atmel Studio / Microchip Studio with the ASF or Harmony 3 framework, and respect the 64-pin TQFP exposed-pad land pattern for adequate thermal dissipation, as the die dissipates more heat than smaller QFN-package SAM D20 variants. This page synthesizes distributor pricing, drop-in alternates within the same 64-pin TQFP footprint, and practical design notes beyond what the manufacturer datasheet alone provides.

Cotação Contato
ATSAMD20J15A-ANT - 32KB Flash Cortex-M0+ MCU, 64-TQFP | Microchip
ATSAMD20J15A-ANT

ATSAMD20J15A-ANT - 32KB Flash Cortex-M0+ MCU, 64-TQFP | Microchip

The Microchip Technology ATSAMD20J15A-ANT is a 32-bit ARM Cortex-M0+ based microcontroller from the SAM D20 family, featuring 32 KB of Flash and 4 KB of SRAM, a 48 MHz CPU clock, and a 64-pin TQFP (10x10 mm) package. This low-power MCU integrates a 12-bit ADC, a 10-bit DAC, multiple serial communication peripherals, and a Peripheral Touch Controller (PTC), making it suited for mixed-signal embedded designs. According to the Microchip product page, the ATSAMD20J15 is engineered for low-power, high-performance applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable I/O peripherals on one IC. Within the broader taxonomy, the Cortex-M0+ belongs to the ARM Cortex-M family of energy-efficient 32-bit cores aimed at microcontroller-class workloads. The SAM D20 family sits in Microchip's lineup of ultra-low-power Cortex-M0+ devices, optimized for sensor interfacing, battery-powered designs, and human-machine interface (HMI) applications where deterministic real-time response and low active/standby current are required. Key features of the ATSAMD20J15A-ANT include an operating voltage range of 1.62 V to 3.63 V, support for industrial temperature grades (-40°C to +105°C), an 8-channel 12-bit ADC with sample averaging and oversampling, a 10-bit 350 ksps DAC, six SERCOM modules configurable as UART/SPI/I2C, and a 256-channel Peripheral Touch Controller supporting capacitive buttons, sliders, and wheels. The device also integrates an RTC, multiple timer/counters, a Watchdog timer, and a 32.768 kHz RTC oscillator. Architecturally, the ATSAMD20J15A-ANT uses the Cortex-M0+ core with a single-cycle multiplier and SysTick timer. The bus matrix supports concurrent access to Flash and SRAM, and a DMA controller offloads data movement for ADC conversions and SERCOM transfers. The Event System allows peripherals to trigger one another without CPU intervention, reducing latency and active-mode power. Typical applications include home automation sensor nodes, consumer HMI with capacitive touch panels, industrial metering, IoT edge devices, and low-cost motor control. Designers leverage the SAM D20 ecosystem (Atmel Studio/Microchip Studio, ASF, and MPLAB X with MCC) for rapid firmware development. When designing with this device, ensure the supply rail stays within 1.62 V to 3.63 V. Place decoupling capacitors close to each VDD pin, and consider using the Idle and Standby sleep modes plus the Sleepwalking feature to minimize average current consumption. This page synthesizes distributor pricing, drop-in alternatives from the SAM D20 family, and practical design notes that go beyond what the manufacturer datasheet alone provides.

Cotação Contato
ATSAMD20J15A-AUT - 48MHz Cortex-M0+ MCU 32KB Flash 64-LQFP | Microchip
ATSAMD20J15A-AUT

ATSAMD20J15A-AUT - 48MHz Cortex-M0+ MCU 32KB Flash 64-LQFP | Microchip

The Microchip Technology ATSAMD20J15A-AUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, featuring 32KB of Flash and 4KB of SRAM, operating up to 48MHz, and packaged in a 64-pin LQFP (10x10 mm). The "AUT" suffix denotes the automotive grade variant qualified to AEC-Q100, with operating voltage 1.62V-3.63V and temperature range -40C to +125C, while the standard industrial grade is limited to -40C to +85C at full speed. The SAM D20 family integrates the Cortex-M0+ core with Microchip's peripheral touch (PTC), SERCOM, ADC, and Event System, achieving 2.14 CoreMark/MHz. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), data memory (SRAM), and integrated peripherals such as timers, communication interfaces, and ADCs. The Cortex-M0+ architecture belongs to the ARM Cortex-M family optimized for embedded applications, offering deterministic interrupt latency, Thumb-2 instruction set, and low power consumption. Microcontrollers sit at the top of the embedded computing hierarchy: transistor -> logic gate -> processor core -> microcontroller -> embedded system. The "low-power" designation reflects sleep modes below 1uA typical, suitable for battery-powered IoT devices. Key features of the ATSAMD20J15A-AUT include up to 48MHz core clock, 32KB Flash, 4KB SRAM, 6 SERCOM channels (configurable as UART/SPI/I2C), a 12-bit ADC with up to 16 channels, multiple timers (TC, TCC), I2S, USB 2.0 Full-Speed, and a 6-channel peripheral touch controller. The 64-pin LQFP package provides generous GPIO (up to 52 I/O) for breadboard-friendly prototyping and industrial interfaces. The Cortex-M0+ core uses a von Neumann bus architecture with single-cycle GPIO access, enabling deterministic bit-banging protocols when needed. The Event System allows inter-peripheral signaling without CPU intervention, reducing active mode power and improving real-time responsiveness. The 12-bit ADC delivers up to 350ksps with hardware averaging and oversampling support, and the SERCOM modules can each be independently configured as UART, SPI, I2C, or LIN master, providing flexibility across protocols. Typical applications include home automation nodes, smart metering, consumer electronics, industrial sensor interfaces, automotive body controllers, and IoT edge devices. The AEC-Q100 qualification of the AUT variant makes it suitable for under-hood and cabin automotive applications where extreme temperatures are encountered. When designing with this part, ensure the 1.62V-3.63V supply rail is decoupled with a 100nF ceramic capacitor close to each VDD pin. The ATSAMD20J15A-AUT requires Atmel Studio / Microchip Studio or MPLAB X IDE for firmware development, with ASF (Advanced Software Framework) or Harmony 3 drivers available for all peripherals. This page synthesizes distributor pricing, AEC-Q100 automotive-grade drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
ATSAMD20J15A-CNT - 32KB Flash Cortex-M0+ MCU 64-UFBGA | Microchip
ATSAMD20J15A-CNT

ATSAMD20J15A-CNT - 32KB Flash Cortex-M0+ MCU 64-UFBGA | Microchip

The Microchip ATSAMD20J15A-CNT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20J family, offering up to 48 MHz core performance, 32 KB of Flash, and 4 KB of SRAM in a 64-pin UFBGA (5x5 mm) package. It operates from 1.62 V to 3.63 V across industrial temperature ranges and integrates a rich peripheral set including SERCOM, ADC, DAC, and timers. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ATSAMD20J15 belongs to the Cortex-M0+ architecture family, the smallest and most energy-efficient ARM core for embedded use, sitting under Cortex-M0/M3/M4 in performance hierarchy. The SAM D20 series specifically targets low-power, mixed-signal applications with on-chip 12-bit analog and serial communication engines, fitting between 8-bit PIC MCUs and higher-performance Cortex-M4 parts in Microchip's portfolio. Key features include six SERCOM serial engines configurable as UART, SPI, or I2C, a 12-bit 350 ksps ADC with up to 16 channels, a 10-bit 350 ksps DAC, six 16-bit Timer/Counters, and a full-speed USB 2.0 device interface. The device supports up to 48 MHz operation from 1.62 V to 3.63 V at -40C to +85C and includes an Event System for inter-peripheral signaling without CPU intervention. The SAM D20 uses a single-cycle hardware multiplier, single-cycle 32-bit load/store, and Microchip's Sleepwalking technology that lets peripherals wake the CPU only when needed. The integrated 32 KB Flash supports live update via the built-in bootloader, and 4 KB SRAM provides deterministic data handling for real-time control loops. Typical applications include home automation sensor nodes, consumer wearables, smart metering endpoints, industrial HMI front-ends, and low-power wireless sensor hubs. The Cortex-M0+ instruction set is binary-compatible with the broader ARM ecosystem, enabling portable firmware development with GCC, IAR, and Keil toolchains. When designing with the ATSAMD20J15A-CNT, ensure the UFBGA-64 footprint supports 0.4 mm pitch routing, add a 1 uF and 0.1 uF decoupling pair near each power pin, and follow Microchip's SAM D20 hardware design checklist for USB impedance control when the USB interface is enabled. This page consolidates distributor pricing, drop-in compatible alternatives, and practical design notes not found in a single manufacturer datasheet.

Cotação Contato
ATSAMD20J15A-CU - ARM Cortex-M0+ MCU, 48MHz, 32KB Flash, 64-UFBGA | Microchip
ATSAMD20J15A-CU

ATSAMD20J15A-CU - ARM Cortex-M0+ MCU, 48MHz, 32KB Flash, 64-UFBGA | Microchip

The Microchip Technology ATSAMD20J15A-CU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, operating at up to 48 MHz with 32 KB of flash and 4 KB of SRAM, housed in a 64-ball UFBGA package (5x5 mm). It is built around the Cortex-M0+ core with single-cycle I/O access, providing high code density and deterministic interrupt response for cost-sensitive embedded applications. The device integrates a 12-bit ADC, 10-bit DAC, multiple SERCOM channels, and a Peripheral Touch Controller (PTC), enabling sensor, communication, and human-interface functions on a single die. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by ARM Holdings as the most energy-efficient member of the Cortex-M family. It targets low-power embedded applications that benefit from 32-bit performance, Thumb-2 instruction set compatibility, and deterministic interrupt latency, while remaining cheaper and lower-power than Cortex-M3/M4 cores. Within the broader taxonomy: Cortex-M0+ -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded IC -> semiconductor. The SAM D20J series extends this core with Microchip's proprietary peripheral set, including event system, DMA, and sleepwalking peripherals that let peripherals wake the CPU only when needed. Key features of the ATSAMD20J15A-CU include: six SERCOM ports (each configurable as USART, I2C, or SPI), a 12-bit 350 ksps ADC with up to 20 channels, a 10-bit DAC, a full-speed USB 2.0 device interface, an RTC with calendar mode, and 256-channel Peripheral Touch Controller support. The device supports 1.62V to 3.63V supply, has a low-power SleepWalking architecture, and includes an Event System for inter-peripheral signaling without CPU intervention. Programming is via Microchip's Atmel-ICE, SAM-ICE debuggers, or the on-board bootloader through the SWD interface. From an architectural standpoint, the ATSAMD20J15A-CU uses a two-layer AHB-Lite bus matrix that separates I/O and DMA traffic from CPU instruction fetches, helping maintain deterministic latency even when multiple peripherals are active. The integrated voltage regulator supports a single 1.8V-3.3V rail with brown-out detection, while an optional 32.768 kHz crystal oscillator enables RTC calendar operation without an external MCU clock. Typical applications include home automation endpoints, smart metering, low-cost consumer electronics, IoT sensor nodes, capacitive-touch human-interface modules, and industrial sensor hubs. The combination of USB, multiple SERCOM, and ADC channels makes it well-suited to bridge devices that aggregate sensor data and forward it via wired or wireless links. When designing with this MCU, pay attention to the UFBGA-64 footprint: it requires NSMD pads with 0.4 mm pitch and precise reflow profile. Use 4-layer PCB stack-up with a continuous ground plane under the BGA to ensure stable JTAG/SWD debug operation and to manage thermal dissipation of the internal LDO. This page synthesizes distributor pricing, same-brand drop-in alternatives, cross-brand equivalents, and practical design notes not found in the bare manufacturer datasheet, giving a faster procurement and BOM decision for engineers.

Cotação Contato
ATSAMD20J15A-MN - ARM Cortex-M0+ MCU 48MHz 32KB Flash | Microchip
ATSAMD20J15A-MN

ATSAMD20J15A-MN - ARM Cortex-M0+ MCU 48MHz 32KB Flash | Microchip

The Microchip Technology ATSAMD20J15A-MN is a 32-bit ARM Cortex-M0+ based flash microcontroller from the SAM D20J series, operating at up to 48MHz and housed in a 64-pin VFQFN exposed-pad package (9x9 mm). The device integrates 32KB of Flash program memory and 4KB of SRAM, making it suited for a wide range of home automation, consumer, metering, and industrial embedded applications. It supports an operating voltage range of 1.6V to 3.6V and is qualified for industrial temperature grades up to +105C. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM), and a rich set of programmable peripherals (GPIO, timers, ADC, communication buses) on a single die. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for deterministic real-time embedded control with a Thumb-2 instruction subset and a tightly coupled interrupt controller (NVIC). The ATSAMD20J15A belongs to the broader category hierarchy of microcontroller -> embedded processor -> system-on-chip (SoC) -> semiconductor IC, and uses Microchip's SAM D20 peripheral set that is shared across the family for firmware portability. Key features include a 12-bit ADC with up to 16 channels, multiple SERCOM interfaces configurable as UART/SPI/I2C, a 16-bit timer/counter, a 32-bit RTC, and the Microchip Event System for inter-peripheral signaling without CPU intervention. The device reaches 2.14 CoreMark/MHz and offers low-power Sleep and Standby modes with fast wake-up, suited to battery-powered IoT endpoints. An on-chip 32kHz oscillator and a flexible clock management unit reduce external BOM. Architecture-wise, the ATSAMD20J15A-MN uses a single-cycle hardware multiplier, a 32-bit system bus, and a separate AHB/APB bridge topology that allows high-speed peripherals (SERCOM, ADC) and low-speed peripherals to be clocked independently for power optimization. The Event System routes peripheral triggers over a dedicated network fabric, offloading many CPU tasks that would otherwise require interrupt-driven servicing. Typical applications include smart-home sensor nodes, low-power wireless MCU companions (paired with an external radio), HVAC fan and damper controllers, electricity metering front-ends, USB human-interface class devices, and general-purpose industrial control boards. The wide temperature range also suits outdoor enclosures and lighting control gear. When designing with this part, ensure the exposed pad (EP) on the 64-VFQFN is soldered to a sufficiently large copper pour for thermal dissipation and electrical ground reference; the package's HVQCCN terminal form does not provide stable operation without it. Decoupling capacitors should be placed as close as possible to each VDD pin pair per the SAM D20 hardware checklist. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for component selection.

Cotação Contato
ATSAMD20J15A-MNT - 32KB Flash Cortex-M0+ MCU | Microchip | 64-QFN
ATSAMD20J15A-MNT

ATSAMD20J15A-MNT - 32KB Flash Cortex-M0+ MCU | Microchip | 64-QFN

The Microchip Technology ATSAMD20J15A-MNT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, featuring 32KB of Flash and 4KB of SRAM in a 64-pin QFN (9x9 mm) package with exposed thermal pad. It operates up to 48MHz and reaches 2.14 CoreMark/MHz, delivering efficient deterministic performance for embedded applications. An ARM Cortex-M0+ microcontroller is a low-power 32-bit processor core designed by ARM Holdings for cost-sensitive embedded applications. The Cortex-M0+ belongs to the ARMv6-M architecture family and is the smallest and most energy-efficient core in the Cortex-M lineup, typically featuring single-cycle I/O, a Wake-up Interrupt Controller (WIC), and optional Micro Trace Buffer (MTB). It sits within a hierarchy of microcontroller → embedded processor → semiconductor device, and combines a CPU core with on-chip memory, peripherals, and interrupt controllers on a single silicon die. The SAM D20J family specifically targets low-power connected applications in home automation, consumer, metering, and industrial segments. The ATSAMD20J15A-MNT integrates the Cortex-M0+ core with 32KB Flash, 4KB SRAM, and the Microchip peripheral set including SERCOM (I2C/SPI/UART), 12-bit ADC, 10-bit DAC, and a full-speed USB 2.0 device controller on the larger-pin variants. The device supports 1.62V to 3.63V operating voltage, multiple low-power sleep modes (IDLE, STANDBY, BACKUP), and a 32.768kHz RTC. Its 48MHz maximum clock with single-cycle multiplier enables responsive control loops while preserving energy budget. Architecturally, the SAM D20J uses a single-cycle I/O port structure, an event system for inter-peripheral signaling without CPU wake-ups, and a peripheral touch controller (PTC) supporting hardware-driven capacitive sensing. The device is manufactured on a low-leakage process and uses a bundled peripheral event fabric so GPIO, timers, and SERCOM modules can interact autonomously, offloading the core and reducing average power in sensor-driven designs. Typical applications include battery-powered IoT sensor nodes, smart home automation hubs, industrial metering, consumer human-interface devices, and low-power wireless companion controllers. The Cortex-M0+ + Cortex-M Software Interface Standard (CMSIS) ecosystem and the MPLAB X IDE / Harmony 3 framework simplify firmware migration within the SAM family and to/from PIC MCUs. A key design consideration is the QFN-64 (9x9) thermal pad - it MUST be soldered to a properly sized thermal copper pour to meet the datasheet's 64-QFN thermal resistance specifications and ensure reliable operation. Designers migrating from the SAM D20 to the SAM D21 family (Cortex-M0+ to Cortex-M0+ upgrade) gain DMA and faster ADC, but the pinout is largely compatible. This page synthesizes distributor pricing, drop-in SAM D20J family alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
ATSAMD20J15B-AUT - 32KB Flash Cortex-M0+ MCU | Microchip
ATSAMD20J15B-AUT

ATSAMD20J15B-AUT - 32KB Flash Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD20J15B-AUT is an ARM Cortex-M0+ based 32-bit microcontroller from the SAM D20J family, featuring 32KB of Flash and 4KB of SRAM, running at up to 48 MHz, and housed in a 64-pin TQFP-EP (10x10 mm) package with exposed thermal pad. Headline parameters: 32 KB Flash, 4 KB SRAM, 48 MHz Cortex-M0+ core, 64-pin TQFP-EP. The part operates from a single 1.62V to 3.63V supply and includes a 12-bit ADC, 10-bit DAC, and 256-channel Peripheral Touch Controller (PTC). A Cortex-M0+ microcontroller is a 32-bit ARM processor core optimized for ultra-low-power embedded applications. The M0+ architecture is the smallest and most energy-efficient member of the ARM Cortex-M family, providing Thumb-2 instruction set compatibility and deterministic interrupt response. The ATSAMD20J15B-AUT integrates this core with Microchip's proprietary Peripheral Touch Controller (PTC) for capacitive touch sensing, on-chip analog peripherals, and SERCOM (Serial Communication Interface) modules that are reconfigurable as UART, SPI, or I2C. The hierarchy: Cortex-M0+ -> ARM 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. Key differentiating specifications include six SERCOM communication interfaces, six timer/counters, a real-time clock (RTC), and full-speed USB device support. The integrated PTC supports up to 256 channels of self/mutual capacitive touch sensing, enabling touch button, slider, and proximity designs without external touch ICs. The 12-bit ADC achieves up to 350 ksps with hardware averaging, while the 10-bit DAC supports sample rates up to 350 ksps for waveform generation. The ATSAMD20J15B-AUT implements Microchip's SleepWalking technology and multiple power domains, achieving active current of approximately 70 uA/MHz and standby current down to a few microamps in deep-sleep modes. The 64-pin TQFP-EP package exposes a thermal pad that can be soldered to the PCB ground plane for improved thermal performance and electrical grounding of analog references. Typical applications include home automation nodes, smart appliance control panels, capacitive touch user interfaces, low-cost consumer electronics, industrial sensor hubs, and USB device peripherals. The PTC peripheral makes this MCU particularly attractive for replacing mechanical buttons with capacitive touch in sealed enclosures. When designing with this device, allocate one of the six SERCOM modules per required communication interface and verify the 64-pin TQFP-EP pinout against your PCB footprint early in the design cycle. The exposed pad must be soldered to a sufficiently large copper pour for thermal dissipation and analog reference stability; failure to do so can degrade ADC performance. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not consolidated on the manufacturer product page alone, with source-traced data verified as of 2026-09-21.

Cotação Contato
ATSAMD20J15B-MU - ARM Cortex-M0+ 32KB Flash MCU | Microchip
ATSAMD20J15B-MU

ATSAMD20J15B-MU - ARM Cortex-M0+ 32KB Flash MCU | Microchip

The Microchip ATSAMD20J15B-MU is a 32-bit ARM Cortex-M0+ microcontroller running up to 48 MHz with 32 KB of Flash and 4 KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package. It integrates a high-performance peripheral set including SERCOM, ADC, timers, and an Event System while operating from 1.62V to 3.63V. The "MU" suffix indicates an industrial temperature range (-40C to +85C), Pb-free (green) compliance, and surface-mount 64-VQFN with exposed pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripherals into one package. The ARM Cortex-M0+ is the smallest and most energy-efficient ARM core, optimized for embedded deterministic control in IoT, sensor nodes, and battery-powered devices. The SAMD20 family from Microchip combines this ARM core with Microchip's SAM peripherals (SERCOM, TCC, ADC, DAC) to deliver an MCU hierarchy of Cortex-M0+ MCU -> microcontroller -> embedded processor -> semiconductor, suited to general-purpose mixed-signal applications. Key features of the ATSAMD20J15B-MU include six SERCOM serial communication interfaces (configurable as UART/SPI/I2C), a 12-bit ADC with up to 12 channels, a 10-bit DAC, two 16-bit timers, a 24-bit timer, and a full-speed USB 2.0 device interface. It supports up to 52 GPIO, has an Event System for inter-peripheral signaling without CPU overhead, and offers low-power Sleep, Standby, and Backup modes with sub-microamp standby current. The integrated Peripheral Touch Controller (PTC) supports capacitive touch hardware-accelerated scanning. The device is built on an advanced low-power CMOS process with a 2.4 mA/MHz active current at full 48 MHz operation. The SERCOM modules can each be reconfigured independently, dramatically reducing BOM cost by letting one physical interface serve as UART, SPI, or I2C as design needs evolve. The integrated SleepWalking peripheral-event wake system lets peripherals wake the CPU only when meaningful data arrives, ideal for battery-powered IoT endpoints. Typical applications include home automation controllers, smart thermostats, sensor hubs, industrial sensor nodes, low-power wireless IoT gateways, wearable fitness bands, capacitive touch user interfaces, USB-CDC bridge dongles, and consumer appliance control boards. The 32 KB Flash and 4 KB SRAM are well-matched to medium-complexity IoT edge stacks running FreeRTOS or ASF firmware. When designing with this MCU, decouple VDDIN/VDDIO with 100 nF X7R ceramics placed within 2 mm of each power pin, and connect the exposed thermal pad to a continuous ground plane for thermal and electrical performance. Use the SERCOM peripheral-mux feature to remap I/O as your pinout evolves, and consider ATSAMD20J14B-MU (16 KB Flash) as a cost-down option if you do not need 32 KB. This page synthesizes distributor pricing, drop-in SAMD20 alternatives, and practical hardware design notes not found in the standalone Microchip datasheet.

Cotação Contato
ATSAMD20J15B-MUT - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip
ATSAMD20J15B-MUT

ATSAMD20J15B-MUT - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip

The Microchip ATSAMD20J15B-MUT is an ARM Cortex-M0+ based 32-bit flash microcontroller from the SAM D20 family, integrating 32KB of Flash and 4KB of SRAM, and operating at up to 48MHz in a 64-pin VQFN (9x9 mm) package with exposed thermal pad. What is an ARM Cortex-M0+ microcontroller? It is the most energy-efficient member of the ARM Cortex-M processor family, designed for low-cost, low-power embedded applications. The Cortex-M0+ core sits within the broader taxonomy of microcontrollers (MCU) -> embedded processors -> semiconductors. The SAM D20 family is a low-power, high-performance line of M0+ MCUs from Microchip (formerly Atmel), popular for general-purpose embedded designs. Key features include a 32KB in-system programmable Flash with ECC, 4KB SRAM, an 8-channel Event System for inter-peripheral signalling, a 12-bit 350ksps ADC with up to 20 analog channels, and a full-speed USB 2.0 device interface. The SERCOM (Serial Communication Interface) module provides up to six configurable I2C/SPI/UART interfaces, and the device supports 1.62V to 3.63V core and I/O operation. Six 16-bit Timer/Counters (TC), a 32-bit Real-Time Counter, and a Peripheral Touch Controller (PTC) supporting capacitive touch sensing round out the peripheral complement. At the architecture level, the SAM D20 uses a single-cycle hardware multiplier, Microchip's proprietary SleepWalking technology for peripheral-level power gating, and an integrated Power Management Unit (PMU) with Buck/LDO modes. This yields Active mode currents of approximately 70 uA/MHz and Sleep modes down to a few microamps, making it competitive with other low-power M0+ MCUs. Typical applications include home automation, IoT sensor nodes, smart metering, consumer electronics, industrial sensor hubs, and capacitive touch user interfaces. The wide operating voltage range and low-power SleepWalking peripherals make it especially suitable for battery-powered devices. When designing, note that the 64-pin VQFN-EP (9x9) package requires careful PCB thermal pad soldering for proper operation. Decoupling should include 100nF + bulk capacitance close to each supply pin per Microchip's hardware design guidelines.

Cotação Contato
ATSAMD20J16A-AUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20J16A-AUT

ATSAMD20J16A-AUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology (formerly Atmel) ATSAMD20J16A-AUT is a 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D20J family, integrating 64KB of Flash and 8KB of SRAM in a 64-pin TQFP (10x10mm) package. It operates from 1.62V to 3.63V supply at up to 48MHz core clock, and is qualified for the industrial -40C to +85C temperature range with tape-and-reel packaging. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripheral interfaces such as GPIO, timers, ADC, and communication controllers on one die. The SAM D20 family sits in the broader hierarchy: microcontroller -> embedded processor -> semiconductor device. Within Microchip's lineup it belongs to the SAME (Smart ARM Microcontroller Embedded) series, which also includes the SAM D21, SAM C20, SAM C21, SAM L21 and SAM D10/D11 sub-families. Key features of the ATSAMD20J16A-AUT include an ARM Cortex-M0+ core running up to 48MHz, the Microchip Event System for low-latency inter-peripheral signalling, a 12-bit 1MSPS ADC with up to 16 analog channels, SERCOM (Serial Communication Interface) modules configurable as UART/SPI/I2C, a full-speed USB 2.0 device controller, and an on-chip 32kHz oscillator plus PLL for system clock. The integrated SleepWalking peripheral allows peripherals to wake the core only when needed. The Cortex-M0+ core implements the ARMv6-M architecture with single-cycle I/O port access and a 2-stage pipeline, delivering 0.9 DMIPS/MHz while drawing only 9 uA/MHz in active mode. Hardware divide and atomic bit manipulation accelerate bare-metal and RTOS-based firmware, while the single-wire debug interface (SWD) removes the need for a JTAG header in low-pin-count designs. Typical applications include home automation endpoints, smart metering, IoT sensor nodes, consumer appliances, low-cost HMI panels, and industrial control sub-systems. The wide 1.62V-3.63V supply window lets the device run directly from a single Li-ion cell or a 3.3V regulated rail, simplifying battery-powered designs. When migrating from AVR to ARM, plan for vector-table setup, ARMv6-M interrupt priorities, and the SERCOM peripheral model rather than AVR USART/TWI registers. Always decouple VDD with a 100 nF X7R ceramic placed within 3 mm of the supply pin and provide a 4.7 uF bulk capacitor on the analog supply rail for ADC accuracy. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone, giving procurement, firmware and hardware engineers a single reference for the ATSAMD20J16A-AUT.

Cotação Contato
ATSAMD20J16A-CN - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20J16A-CN

ATSAMD20J16A-CN - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology ATSAMD20J16A-CN is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, featuring 64 KB of Flash program memory, 8 KB of SRAM, and a maximum CPU clock speed of 48 MHz, housed in a 64-ball UFBGA (5x5 mm) package. It integrates the Cortex-M0+ core with Microchip's peripheral touch controller (PTC) and a rich set of serial interfaces including SERCOM (I2C/SPI/UART), I2S, and USB-free connectivity, targeting low-power embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and configurable peripherals onto one silicon die. The Cortex-M0+ core, designed by Arm, is the smallest and most energy-efficient of the Cortex-M family, optimized for deterministic interrupt response and minimal gate count. Within the broader taxonomy, the ATSAMD20J16A-CN sits inside the SAM D20 family -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor, providing the system-on-chip foundation for connected and battery-powered products. Key features of the ATSAMD20J16A-CN include six SERCOM-configurable serial channels, a 12-bit 350 ksps analog-to-digital converter (ADC) with up to 20 channels, a 10-bit 350 ksps digital-to-analog converter (DAC), a 16-bit timer/counter, and a full-speed USB 2.0 device interface (note: USB pins are not bonded out on the 64-pin UFBGA variant). It also provides a Real-Time Clock (RTC) with calendar mode, up to 52 general-purpose I/O pins, and a Peripheral Touch Controller supporting buttons, sliders, and proximity sensing via capacitive sensing. The device is fabricated on a low-power CMOS process and offers multiple sleep modes (IDLE, STANDBY, BACKUP) with typical RTC backup current around 1 µA, enabling years of operation from a single coin cell when duty-cycled. The integrated 32.768 kHz oscillator and PLL-derived 48 MHz system clock let designers trade computational throughput against quiescent draw on a per-application basis, while the Single-Voltage 1.6 V to 3.6 V supply range simplifies direct battery connection. Typical applications for the ATSAMD20J16A-CN include home automation nodes, low-power IoT sensor endpoints, consumer electronics such as wearables and remote controls, smart metering, and industrial sensor front-ends. Its mix of low-power sleep modes, robust ADC, and configurable SERCOM blocks suits designs where BOM consolidation and long battery life outweigh raw throughput. When designing with this part, take care to populate the decoupling network recommended in the datasheet and verify the chosen boot configuration strap pins (BOOTPROT/PMUX) match your in-system programmer flow. The 64-ball UFBGA requires careful PCB layout with microvia or via-in-pad technology for reliable assembly on inner layers. This page synthesizes distributor pricing tiers, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving engineers a single reference for evaluation, sourcing, and PCB integration decisions.

Cotação Contato
ATSAMD20J16A-CU - 64KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD20J16A-CU

ATSAMD20J16A-CU - 64KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD20J16A-CU is an ultra-low-power 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20J family, integrating 64 KB of Flash and 8 KB of SRAM in a 64-ball UFBGA (5x5 mm) package. It runs at up to 48 MHz and supports an operating voltage range of 1.62V to 3.63V, making it compatible with 1.8V, 2.5V, and 3.3V power domains commonly found in modern IoT designs. Key features include the Cortex-M0+ core delivering 1.25 DMIPS/MHz, hardware single-cycle multiplier, and Microchip's proprietary Event System for inter-peripheral signaling without CPU intervention. The device integrates 6 SERCOM (Serial Communication) channels configurable as UART, SPI, or I2C, a 12-bit 350 ksps ADC, 10-bit 350 ksps DAC, two analog comparators, and a 32-bit RTC. Sleep current is rated below 8 uA with full RAM retention, and an integrated SleepWalking peripheral controller enables autonomous peripheral operation to further reduce wake events. What is a low-power microcontroller? A low-power microcontroller (MCU) is a microprocessor optimized for minimal active and standby energy consumption, typically targeting battery-powered or energy-harvesting applications. The SAM D20 family sits within the broader microcontroller taxonomy (microcontroller -> embedded controller -> system-on-chip -> semiconductor), and is specifically engineered to combine Cortex-M0+ processing with peripheral event-driven wake-up so the CPU stays asleep until real work is required. The ATSAMD20J16A-CU utilizes a 2-layer AHB bus matrix with separate code and data paths, allowing simultaneous Flash access and peripheral DMA. Hardware cryptographic support is absent, but the device integrates a true random number generator (TRNG), CRC-32, and a 32-bit hardware AES peripheral on select variants. Full-speed USB 2.0 device support requires an external PHY, and the device includes a 12-channel DMA controller with flexible descriptor chaining. Typical applications include IoT sensor nodes and BLE beacons, smart home automation hubs, home appliance user interfaces, industrial sensor transmitters, and low-power wireless remote controls. The 64-pin UFBGA package suits compact PCB designs where board area is constrained and BGA assembly is acceptable. When designing with the ATSAMD20J16A-CU, ensure the UFBGA land pattern is designed per JEDEC MS-026 with NSMD pads for reliable BGA reflow. The device supports Atmel START code configuration and ASF/ASFv4 drivers, enabling rapid firmware prototyping with example projects for FreeRTOS and tickless sleep modes. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes that are not found in the manufacturer datasheet alone, with all values cross-checked against real-time distributor inventory as of 2026-09-21.

Cotação Contato
ATSAMD20J16A-MN - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20J16A-MN

ATSAMD20J16A-MN - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip (formerly Atmel) ATSAMD20J16A-MN is an ARM Cortex-M0+ based 32-bit microcontroller running up to 48 MHz with 64 KB of Flash and 8 KB of SRAM, housed in a 64-pin QFN (9x9 mm) industrial-grade package. It is part of the SAM D20J family, a low-power, high-performance line targeting home automation, consumer, metering, and industrial applications. The device integrates a 12-channel 12-bit SAR ADC, two I2C, up to six SERCOM (configurable serial), six 16-bit timers, RTC, and full-speed USB 2.0 device support through a dedicated USB module on the J variant, plus a capacitive touch (PTC) peripheral and 6-channel DMA for low-overhead peripheral moves. Background: a microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and programmable peripherals on one die. ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M family, using the Thumb-2 instruction set and designed for deterministic interrupt response in low-power embedded systems. The Cortex-M0+ class sits within the broader hierarchy: microcontroller -> embedded processor -> SoC -> semiconductor. Compared to 8-bit AVR MCUs that Microchip also sells, the SAM D20 offers higher code density, faster arithmetic, and modern serial peripherals such as SERCOM and USB. Key features of the ATSAMD20J16A-MN include 64 KB Flash, 8 KB SRAM, up to 48 MHz CPU clock, 1.62 V to 3.63 V wide VDD range, low-power Sleep and Idle modes drawing a few microamps, a 12-channel 12-bit 350 ksps ADC, two I2C ports, three SPI, six UART, full-speed USB 2.0 device, and a Peripheral Touch Controller supporting capacitive buttons and sliders. The integrated 6-channel DMA engine offloads memory-move and peripheral-streaming work from the Cortex-M0+ core, freeing cycles for application logic. On the architecture side, the SAM D20 uses a two-layer AHB-Lite bus matrix with bridges to APB for peripherals, single-cycle 32x32 hardware multiplier, and a SysTick timer. The 64-pin QFN package exposes 52 GPIO plus dedicated USB D+/D- and XIN/XOUT pins. Programming is supported by Microchip Studio (formerly Atmel Studio), MPLAB X IDE, and the on-board SAM-BA bootloader over USB or UART. Typical applications include IoT sensor nodes, smart-home appliances (thermostats, white-goods HMIs), portable medical devices, industrial control boards, USB HID peripherals (keyboards, mice, custom input devices), and LoRaWAN/Zigbee sensor endpoints. The wide 1.62-3.63 V supply range allows direct Li-ion battery operation with a low-dropout regulator. When designing with this part, budget for a 32.768 kHz crystal if accurate RTC timing is required, and add a 1uF plus 100 nF decoupling pair near each VDD pin. Use the SERCOM multiplexer rather than fixed-position UART/SPI/I2C pins to remap peripherals when PCB routing forces pin swaps. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotação Contato