Microcontroladores

Produtos (18714)

ATSAMD20J16A-MN - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20J16A-MN

ATSAMD20J16A-MN - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip (formerly Atmel) ATSAMD20J16A-MN is an ARM Cortex-M0+ based 32-bit microcontroller running up to 48 MHz with 64 KB of Flash and 8 KB of SRAM, housed in a 64-pin QFN (9x9 mm) industrial-grade package. It is part of the SAM D20J family, a low-power, high-performance line targeting home automation, consumer, metering, and industrial applications. The device integrates a 12-channel 12-bit SAR ADC, two I2C, up to six SERCOM (configurable serial), six 16-bit timers, RTC, and full-speed USB 2.0 device support through a dedicated USB module on the J variant, plus a capacitive touch (PTC) peripheral and 6-channel DMA for low-overhead peripheral moves. Background: a microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and programmable peripherals on one die. ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M family, using the Thumb-2 instruction set and designed for deterministic interrupt response in low-power embedded systems. The Cortex-M0+ class sits within the broader hierarchy: microcontroller -> embedded processor -> SoC -> semiconductor. Compared to 8-bit AVR MCUs that Microchip also sells, the SAM D20 offers higher code density, faster arithmetic, and modern serial peripherals such as SERCOM and USB. Key features of the ATSAMD20J16A-MN include 64 KB Flash, 8 KB SRAM, up to 48 MHz CPU clock, 1.62 V to 3.63 V wide VDD range, low-power Sleep and Idle modes drawing a few microamps, a 12-channel 12-bit 350 ksps ADC, two I2C ports, three SPI, six UART, full-speed USB 2.0 device, and a Peripheral Touch Controller supporting capacitive buttons and sliders. The integrated 6-channel DMA engine offloads memory-move and peripheral-streaming work from the Cortex-M0+ core, freeing cycles for application logic. On the architecture side, the SAM D20 uses a two-layer AHB-Lite bus matrix with bridges to APB for peripherals, single-cycle 32x32 hardware multiplier, and a SysTick timer. The 64-pin QFN package exposes 52 GPIO plus dedicated USB D+/D- and XIN/XOUT pins. Programming is supported by Microchip Studio (formerly Atmel Studio), MPLAB X IDE, and the on-board SAM-BA bootloader over USB or UART. Typical applications include IoT sensor nodes, smart-home appliances (thermostats, white-goods HMIs), portable medical devices, industrial control boards, USB HID peripherals (keyboards, mice, custom input devices), and LoRaWAN/Zigbee sensor endpoints. The wide 1.62-3.63 V supply range allows direct Li-ion battery operation with a low-dropout regulator. When designing with this part, budget for a 32.768 kHz crystal if accurate RTC timing is required, and add a 1uF plus 100 nF decoupling pair near each VDD pin. Use the SERCOM multiplexer rather than fixed-position UART/SPI/I2C pins to remap peripherals when PCB routing forces pin swaps. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotação Contato
ATSAMD20J16A-MNT - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip
ATSAMD20J16A-MNT

ATSAMD20J16A-MNT - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip

The Microchip Technology ATSAMD20J16A-MNT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, delivering 48 MHz CPU performance with 64 KB of Flash and 8 KB of SRAM in a 64-pin QFN (9x9 mm) package with exposed thermal pad. It operates from 1.62 V to 3.63 V, supports six SERCOM configurable serial interfaces, a 12-bit 1 MSPS ADC, and 10-bit DAC, and targets a wide range of home automation, consumer, metering, and industrial applications. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory (Flash), working memory (SRAM), and peripherals such as timers, ADCs, and communication interfaces. The ARM Cortex-M0+ is the smallest and most energy-efficient core in the Cortex-M family, designed for low-power, cost-sensitive embedded applications. The SAM D20 series extends this with Microchip's peripheral set and event system, sitting within the broader category: Cortex-M0+ MCU -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded computing -> semiconductor. Key features include up to 48 MHz operation via an on-chip 8 MHz oscillator and 48 MHz Digital Frequency-Locked Loop (DFLL), six SERCOM modules that can each be configured as USART, I2C, or SPI, a 12-channel 12-bit 350 kSPS SAR ADC with gain stage, two analog comparators, and a 10-bit 300 kSPS DAC. The device also integrates a full-speed USB 2.0 device interface with internal pull-up and 8 KB of self-calibrating SRAM. Technically, the SAM D20J uses a single-cycle hardware multiplier, single-cycle I/O port access (PORT) for bit-manipulation efficiency, and Microchip's SleepWalking event system that lets peripherals wake the CPU autonomously on I/O activity while keeping the core asleep. The Cortex-M0+ supports the ARMv6-M Thumb instruction set only, optimized for code density. The 64-pin QFN package exposes 52 GPIO and a 4-pin JTAG/SWD debug interface. Typical applications include home automation sensor hubs, smart metering endpoints, low-power wireless sensor nodes, consumer appliances with USB connectivity, industrial control panels, and battery-powered IoT devices. The wide 1.62-3.63 V supply range and multiple low-power modes (IDLE, STANDBY, BACKUP) suit coin-cell and energy-harvesting designs. When designing with the ATSAMD20J16A-MNT, pay attention to the BOOTPROT fuse and the NVMCTRL row-erase granularity (256 bytes). Use the SERCOM pin-muxing tables in the datasheet before PCB layout, because SERCOM pad mapping differs from the pin numbering printed on the package marking. This page synthesizes distributor pricing, drop-in SAM D20 alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware teams evaluate sourcing options.

Cotação Contato
ATSAMD20J16A-MU - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20J16A-MU

ATSAMD20J16A-MU - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology ATSAMD20J16A-MU is a 32-bit ARM Cortex-M0+ based flash microcontroller (SAM D20J family) running at up to 48 MHz, integrating 64 KB of Flash and 8 KB of SRAM in a 64-pin QFN (9x9 mm) package with industrial temperature grade. A microcontroller (MCU) is a single-chip computer that combines a CPU core, RAM, non-volatile program memory (Flash), and a rich set of digital and analog peripherals. The Cortex-M0+ is the most energy-efficient ARM core, designed for deterministic embedded workloads. Within the broader hierarchy, the ATSAMD20J16A-MU is a microcontroller -> 32-bit MCU -> ARM Cortex-M0+ MCU -> SAM D20 family -> low-power family -> semiconductor IC. Key features include the Cortex-M0+ core reaching 2.14 CoreMark/MHz, 64 KB Flash plus 8 KB SRAM, an integrated SERCOM (Serial Communication Interface) block that can be configured as UART/SPI/I2C, a 12-bit ADC, 10-bit DAC, and full-speed USB 2.0 device support on selected variants. The SAM D20J also embeds the Microchip Sleepwalking peripheral event system and an Event System for low-power autonomous peripherals. Architecturally, the SAM D20 family pairs the Cortex-M0+ core with a low-leakage process and a flexible clock tree (internal 48 MHz DFLL, 32.768 kHz oscillator, PLL options). The peripheral event system allows DMA-style data movement without CPU intervention, enabling sleep-mode current consumption in the microamp range while still sampling sensors and toggling I/O. Typical applications include home automation nodes, low-power wireless sensor hubs, consumer human-interface devices (HID), industrial metering, smart LED controllers, and small graphical HMI panels. The wide 1.62-3.6 V supply range supports direct operation from a single Li-ion cell or two AA batteries. Design consideration: when migrating code from ATSAM to other Cortex-M0+ MCUs, verify pin mapping and SERCOM channel allocation - SERCOM instances are multiplexed and must be remapped through the PORT MUX registers. Always consult the device-specific datasheet for pad configuration. This page synthesizes real-time distributor pricing, pin-compatible drop-in alternatives from the same SAM D20J family, and practical low-power design notes beyond what is collected on DigiKey, Mouser, or Octopart.

Cotação Contato
ATSAMD20J16A-MUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20J16A-MUT

ATSAMD20J16A-MUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology ATSAMD20J16A-MUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, featuring 64KB of Flash, 8KB of SRAM, and operating at up to 48 MHz, packaged in a 64-pin QFN (9x9 mm) with exposed thermal pad. The device integrates the Cortex-M0+ core with a 2.14 CoreMark/MHz efficiency, providing 32KB Flash variants in the same family for scalable design migration. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADC, communication interfaces, and GPIO. MCUs are the fundamental building blocks of embedded systems, sitting at the lowest tier of the compute hierarchy: MCU -> embedded processor -> SoC. The Cortex-M0+ is the most energy-efficient ARM core and targets ultra-low-power applications, making the SAM D20 series ideal for battery-powered and always-on devices. Key features of the ATSAMD20J16A-MUT include the Serial Communication Interface (SERCOM) module that provides up to six configurable USART/SPI/I2C channels, a 12-bit ADC with up to 350 ksps sampling rate, a 10-bit DAC, and a full-speed USB 2.0 device interface. The device operates from 1.62 V to 3.6 V, supports Sleep and Idle modes drawing less than 10 uA, and includes the Event System for inter-peripheral signaling without CPU intervention, dramatically reducing power consumption in event-driven designs. The SAM D20 architecture uses a single AHB-APB bus matrix with a dedicated Flash cache and prefetch buffer, eliminating Flash wait states at 48 MHz under most conditions. The integrated voltage regulator supports both linear LDO and DC-DC buck modes, and the brown-out detector with separate thresholds for BOD12, BOD33, and the supply monitor protects against undefined behavior under unstable supply conditions. Typical applications include home automation sensor nodes, consumer wearables, smart metering, industrial control HMI, and low-power wireless IoT end nodes. The 64KB Flash and 8KB SRAM are sufficient for protocol stacks such as BLE, LoRaWAN, or Zigbee when paired with an external transceiver. When designing with this part, note that the QFN-64 package requires careful thermal pad soldering for proper electrical grounding and thermal performance. The Cortex-M0+ lacks a dedicated FPU, so floating-point operations require the optional CMSIS-DSP library or fixed-point math. This page synthesizes distributor pricing, same-family migration alternatives, and design notes not found on typical distributor product pages, helping engineers make informed sourcing and design decisions.

Cotação Contato
ATSAMD20J16B-AN - 64KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD20J16B-AN

ATSAMD20J16B-AN - 64KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD20J16B-AN is a low-power, high-performance ARM Cortex-M0+ based flash microcontroller delivering 48 MHz CPU performance with 64 KB of flash and 8 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package with exposed pad. It operates from 1.62 V to 3.63 V across industrial -40C to +105C temperatures, supporting 52 GPIO, I2C, SPI, and SERCOM-based USART connectivity, plus brown-out detect, POR, and watchdog peripherals. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (flash), data memory (SRAM), and configurable peripherals on a single die. The ARM Cortex-M0+ architecture is a 32-bit RISC core optimized for ultra-low-power embedded applications, while the SAM D20 family targets battery-powered home automation, consumer, metering, and industrial nodes. Within the broader taxonomy, the ATSAMD20J16B-AN sits at: microcontroller -> 32-bit MCU -> ARM Cortex-M0+ MCU -> SAM D20 family -> SAM D20J series. Key features include single-cycle hardware multiplication, a 12-bit 350 ksps ADC with up to 20 channels, two analog comparators, a 32-bit RTC, six SERCOM pads-configurable interfaces, and Event System for inter-peripheral signaling without CPU wakeup. The peripheral touch controller (PTC) supports capacitive touch buttons, sliders, and proximity sensing. Sleep current is typically under 1 uA in deep-sleep with RTC retention, enabling multi-year coin-cell battery operation for wireless sensor nodes and smart meters. The SAM D20 architecture uses an advanced low-power bus matrix with bridge isolation, allowing select peripherals (SERCOM, ADC) to operate while the CPU sleeps. The integrated voltage regulator and POR guarantee clean startup from brown-out conditions. Six flexible clock sources (internal 8 MHz, internal 32 kHz, PLL, DFLL, external crystal, and digital input) allow precision UART baud generation without external crystals in cost-sensitive designs. Typical applications include home automation bridges, smart thermostats, gas/water/heat metering, IoT sensor nodes, industrial control panels, and consumer appliances. The 64-pin TQFP footprint (with exposed pad) gives engineers enough I/O for keypad scanning, LCD segment driving, and multiple SERCOM channels for sensor buses. The AEC-Q100 compliance variant (ATSAMD20J18B-AN) extends this family into automotive body controllers and instrument clusters. When designing with this MCU, allocate the exposed pad (pin 64) to a continuous ground copper pour of at least 25 mm^2 to dissipate up to 1 W of internal dissipation. Decouple VDDIN with 1 uF + 100 nF within 2 mm of the pin, and place the 32.768 kHz crystal within 5 mm of XIN32/XOUT32 for RTC accuracy. Use Microchip's Atmel Studio or MPLAB X IDE with the SAM D20 DFP to develop, and J-Link or EDBG debuggers for flash programming. This page synthesizes current distributor pricing, drop-in alternatives within the SAM D20J footprint, and practical PCB layout notes not collected in any single manufacturer document.

Cotação Contato
ATSAMD20J16B-ANT - 64KB Flash Cortex-M0+ MCU, 64-TQFP | Microchip
ATSAMD20J16B-ANT

ATSAMD20J16B-ANT - 64KB Flash Cortex-M0+ MCU, 64-TQFP | Microchip

The Microchip Technology ATSAMD20J16B-ANT is a 32-bit ARM Cortex-M0+ flash microcontroller delivering up to 48 MHz CPU performance in a 64-pin TQFP (10x10 mm) package. It integrates 64 KB of Flash and 8 KB of SRAM, with an operating voltage range of 1.62V to 3.63V across industrial temperature grades from -40C to +105C. According to the manufacturer product page, this SAM D20 family part targets home automation, consumer, metering, and industrial applications. A microcontroller (MCU) is an integrated circuit containing a processor core, volatile memory (SRAM), non-volatile memory (Flash/EEPROM), and programmable peripherals on a single die. The Cortex-M0+ is the smallest and most energy-efficient ARM core for embedded designs, sitting below Cortex-M3/M4 in feature richness but above 8-bit legacy cores in code density, interrupt latency, and toolchain maturity. Within the broader hierarchy, microcontrollers belong to the Embedded Processing family of semiconductors alongside microprocessors (MPUs), DSPs, and SoCs. Key features of the ATSAMD20J16B-ANT include the single-cycle hardware multiplier Cortex-M0+ core, full-speed USB 2.0 device support, 6 SERCOM (serial communication) interfaces configurable as I2C/SPI/UART, a 12-bit 350 ksps ADC with up to 16 channels, two analog comparators, a 24-bit RTC, and two I2S interfaces for digital audio. Peripherals are mapped through the SAM D20 event system for low-latency hardware signaling between blocks without CPU intervention. The device uses Microchip's proprietary Atmel/Microchip low-power process technology with multiple SleepWalking-enabled power domains. Idle current is in the single-digit microamp range, allowing battery-powered designs to wake on peripheral events while consuming minimal energy. The integrated 8-channel DMA controller offloads data movement from the CPU, further reducing active time and extending battery life. Typical applications include smart-home sensor hubs, industrial control modules (PLCs, motor controllers), electronic metering endpoints, consumer wearables, and USB peripherals. The combination of USB device, ample SRAM for protocol stacks, and rich analog peripherals makes it well suited to bridge nodes that aggregate sensor data and forward it upstream. When designing with the ATSAMD20J16B-ANT, decouple VDD and VDDIO supplies close to the IC and follow Atmel/Microchip AT03488 PCB layout guidelines for the 64-pin TQFP land pattern. Use Microchip Studio or MPLAB X with the SAMD20 device pack to enable the DSU (Device Service Unit) for secure firmware provisioning via SWD. This page synthesizes distributor pricing, same-family Microchip drop-in alternatives, and practical low-power design notes that complement the manufacturer datasheet.

Cotação Contato
ATSAMD20J16B-AU - ARM Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20J16B-AU

ATSAMD20J16B-AU - ARM Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip ATSAMD20J16B-AU is a 32-bit ARM Cortex-M0+ based flash microcontroller delivering up to 48 MHz CPU clock, 64 KB of Flash and 8 KB of SRAM in a 64-pin TQFP industrial-temperature-grade package. Designed for low-power, high-performance embedded applications, it integrates 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), RTC, SERCOM and full Cortex-M0+ debug. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals and I/O into one package. The ARM Cortex-M0+ core places the ATSAMD20 family in the Cortex-M0+ family -> ARM Cortex-M family -> 32-bit RISC MCU -> embedded microcontroller -> semiconductor taxonomy, where it serves as the central control element in connected, sensor-driven or battery-powered products. Key features include 64 KB Flash, 8 KB SRAM, 6 SERCOM (configurable as UART/SPI/I2C), 12-bit 350 ksps ADC with up to 20 channels, 10-bit 350 ksps DAC, 256-channel PTC for capacitive touch, 6-channel DMA, full-speed USB device (when available on the die), RTC with calendar mode, and operating voltage 1.6 V to 3.6 V. Industrial temperature grade (-40 C to +85 C) supports commercial and industrial deployments, and Sleep + Idle + Standby power modes plus a 6-channel Event System keep active power in the microamp range. Architecturally the device pairs an ultra-low-power CMOS process with the Cortex-M0+ core (only 12 KB of code space for the entire Thumb-2 instruction set), a single-cycle hardware multiplier and a fast peripheral interconnect. The SERCOM blocks are pin-mapped so any function (UART, SPI, I2C, LIN master) can be assigned to almost any GPIO, which simplifies PCB routing and footprint reuse across variants. The 12-bit ADC and DAC share a 1 V internal bandgap reference and can be triggered by hardware events or timers for deterministic sampling. Typical applications include home automation sensor nodes, smart metering endpoints, capacitive-touch human-machine interfaces, consumer appliances, low-cost Bluetooth/BLE control hosts, and industrial control modules. The wide 1.6 V to 3.6 V range allows direct connection to single-cell Li-ion (after regulation) or 2x AA batteries. When designing with this MCU, plan decoupling: place 100 nF X7R capacitors on each VDD pin plus a bulk 4.7 uF on the regulator output. The SWD pins (SWDIO, SWDCLK) must be brought out to a 2x5 0.05-inch header for programming and on-board debug with Atmel Studio / MPLAB X and a J-Link, Atmel-ICE or Curiosity board. This page combines distributor pricing, validated drop-in pin-compatible alternatives, and practical design notes that go beyond the manufacturer datasheet to help engineers shorten selection and bring-up time.

Cotação Contato
ATSAMD20J16B-MN - 48MHz Cortex-M0+ MCU, 64KB Flash, 64-VQFN | Microchip
ATSAMD20J16B-MN

ATSAMD20J16B-MN - 48MHz Cortex-M0+ MCU, 64KB Flash, 64-VQFN | Microchip

The Microchip Technology ATSAMD20J16B-MN is a low-power, high-performance ARM Cortex-M0+ flash microcontroller (MCU) operating at up to 48 MHz, housed in a 64-pin VQFN (MN) package with 64KB Flash and 8KB SRAM. The SAM D20 family operates from 1.62V to 3.63V and reaches 2.46 CoreMark/MHz, delivering strong computational throughput for its class. ARM Cortex-M0+ is the most energy-efficient 32-bit ARM processor core, designed for low-cost, low-power microcontrollers that replace legacy 8-bit and 16-bit MCUs while adding thumb/Thumb-2 instruction efficiency and a single-cycle 32x32 hardware multiplier. An MCU (microcontroller unit) is a compact system-on-chip integrating CPU, memory (Flash/SRAM), and peripherals (ADC, timers, communication buses) on a single die; the Cortex-M0+ line is positioned below Cortex-M3/M4 and aimed at cost-sensitive, deterministic applications where every microwatt matters. Key features of the ATSAMD20J16B-MN include 64KB in-system-programmable Flash, 8KB SRAM, a 12-bit 350 ksps SAR ADC with up to 20 channels, a 10-bit 350 ksps DAC, six SERCOM channels reconfigurable as UART/SPI/I2C, a 256-channel Peripheral Touch Controller (PTC), and full-speed USB 2.0 device support. The 48 MHz Cortex-M0+ core, Sleepwalking peripherals, and a low-power RTC running from a 32 kHz crystal enable <1 µA typical standby current with RTC retention, making the part ideal for battery-powered edge devices. Architecturally, the device uses a 2-layer AHB-Lite bus matrix connecting CPU, Flash, SRAM, and peripherals with deterministic zero-wait-state access from SRAM. Peripherals are mapped through a unified SERCOM block (each instance is software-configured into UART/SPI/I2C/SMBus), and the Event System allows DMA-free peripheral-to-peripheral signalling - both features reduce CPU load and active-mode current. Typical applications include home automation endpoints, smart metering, consumer wearables, industrial sensor nodes, USB HID peripherals, and cap-touch user interfaces. The wide 1.62V-3.63V supply range and integrated PTC simplify single-cell Li-ion and 2x AA designs. Designers should review the SAM D20 silicon errata (per the manufacturer datasheet family documents) prior to free-up for production, particularly regarding SERCOM and ADC behaviour. This page synthesises distributor pricing, same-family drop-in alternatives such as ATSAMD20J18B-MN and ATSAMD20J15B-MN, and practical design notes not found in the manufacturer datasheet.

Cotação Contato
ATSAMD20J16B-MNT - ARM Cortex-M0+ MCU 64KB Flash 64-VQFN
ATSAMD20J16B-MNT

ATSAMD20J16B-MNT - ARM Cortex-M0+ MCU 64KB Flash 64-VQFN

The Microchip Technology ATSAMD20J16B-MNT is a 32-bit ARM Cortex-M0+ microcontroller with 64KB Flash, 8KB SRAM, and a 48 MHz CPU core, housed in a 64-pin VQFN (9x9 mm) industrial-grade package. It operates from 1.62V to 3.63V, integrates a 12-bit ADC, a 10-bit DAC, up to 52 programmable I/O pins, and the SERCOM peripheral set, and is qualified for -40C to +105C industrial ambient operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ARM Cortex-M0+ is an energy-efficient 32-bit core designed for deterministic real-time control in deeply embedded systems. Within Microchip's SAM family, the SAM D20 sits at the low-power Cortex-M0+ tier; the broader hierarchy is ARM Cortex-M -> 32-bit MCU -> microcontroller -> semiconductor -> integrated circuit. Engineers choose the SAM D20 line when they need more compute than an 8-bit AVR but tighter power budgets than Cortex-M4/M7 parts. Key features of the ATSAMD20J16B-MNT include 6 SERCOM channels (each configurable as USART, I2C, or SPI), a 12-bit 350 ksps ADC with up to 20 analog channels, a 10-bit 350 ksps DAC, two analog comparators, a 16-bit timer/counter (TC) block with 8 channels, a 32-bit real-time clock, a 256-channel peripheral touch controller (PTC), and full-speed USB 2.0 device support. The 64KB Flash supports in-application programming through the ROM bootloader, and the 8KB SRAM is sufficient for protocol stacks such as Modbus RTU or BLE controller-link layers with offloaded radio. Architecturally, the SAM D20 couples the Cortex-M0+ core (Thumb-2 only, single-cycle I/O port) with a multi-layer AHB/APB bus matrix that lets SERCOM, ADC, DAC, and PTC operate concurrently with low CPU intervention. Idle current of a few microamps in STANDBY with RTC running, plus a 5.8 uA typical deep-sleep figure, makes the part suitable for battery-powered endpoints where the MCU must wake on touch, GPIO, or RTC events. Typical applications include home-automation sensor hubs, smart-metering endpoints, consumer appliances with touch UIs, low-cost industrial sensor nodes, USB HID peripherals, and battery-powered IoT devices. The combination of Cortex-M0+ determinism, generous touch hardware, and USB makes it a strong fit for connected products that need a touch UI plus a tethered debug/update path. A key design tip is to provide a 32.768 kHz crystal on XIN32/XOUT32 when the RTC must track time over sleep; without it, internal DFLL drift dominates long-term accuracy. Also, route VDDANA and VDDIO from the same 3.3V rail through separate ferrite beads to keep ADC noise low during SERCOM-heavy traffic. This page synthesizes distributor pricing, drop-in alternatives, and design notes that the standalone datasheet does not present in one view.

Cotação Contato
ATSAMD20J17A-AN - 48MHz Cortex-M0+ MCU 128KB Flash 64-TQFP | Microchip
ATSAMD20J17A-AN

ATSAMD20J17A-AN - 48MHz Cortex-M0+ MCU 128KB Flash 64-TQFP | Microchip

The Microchip ATSAMD20J17A-AN is a 32-bit ARM Cortex-M0+ based flash microcontroller delivering up to 48 MHz core performance with 128 KB of Flash and 16 KB of SRAM, housed in a 64-pin TQFP industrial-grade package. It operates from 1.62 V to 3.63 V and supports temperatures from -40C to +105C, making it suitable for industrial, consumer, and metering applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable I/O peripherals on a single die. The ATSAMD20J17A-AN belongs to the broader hierarchy of ARM Cortex-M0+ -> Cortex-M series -> 32-bit RISC microcontroller -> embedded processor -> semiconductor IC. As part of Microchip's SAM D20 family, it bridges 8-bit legacy designs to 32-bit performance while preserving low-power operation, a hallmark of the Cortex-M0+ architecture. Key features include a 12-bit ADC and 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC) for capacitive touch sensing, a full-speed USB 2.0 device interface, multiple SERCOM modules (I2C, SPI, UART), a Real-Time Clock (RTC), and six configurable SERCOM ports. The device integrates an Event System, SleepWalking peripherals, and an optional 32 kHz internal oscillator, enabling power-conscious designs with deep-sleep current consumption as low as microampere range. Architecturally, the ATSAMD20J17A-AN uses Microchip's proprietary low-power process technology combined with the ARM Cortex-M0+ core, achieving 0.9 DMIPS/MHz at 48 MHz. The 128 KB Flash and 16 KB SRAM are accessed through a tightly-coupled AHB-Lite bus matrix that minimizes latency for interrupt-driven applications. Hardware CRC, AES, and true random number generator (TRNG) modules support security-sensitive IoT edge nodes. Typical applications include home automation controllers, smart energy metering, industrial sensor nodes, consumer appliances with capacitive touch interfaces, USB peripherals, and low-power IoT edge devices. The integrated 12-bit ADC and 10-bit DAC make it well-suited for mixed-signal front-end designs. When designing with this MCU, allocate proper decoupling (100 nF + bulk 4.7 uF near each VDD pin) and follow Microchip's Atmel START / MPLAB Harmony code-generation flow. Note that the -AN suffix denotes industrial-grade TQFP-64 packaging; for QFN-64 use the -MN variant, and for extended AEC-Q100 temperature use the automotive-qualified suffix. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
ATSAMD20J17A-ANT - 48MHz Cortex-M0+ 128KB Flash MCU | Microchip
ATSAMD20J17A-ANT

ATSAMD20J17A-ANT - 48MHz Cortex-M0+ 128KB Flash MCU | Microchip

The Microchip Technology ATSAMD20J17A-ANT is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D20J family, featuring 128KB of flash, 16KB of SRAM, and a maximum CPU clock of 48MHz. Housed in a 64-pin TQFP (10x10 mm) industrial-grade package with 1.6-3.6V operating range, it integrates a 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller, and RTC for energy-aware embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, timers, communication peripherals, and I/O on one die. The Cortex-M0+ architecture used here belongs to the ARM Cortex-M family, the dominant 32-bit core family in low-power embedded systems. The ATSAMD20J17A-ANT sits inside the SAM D20 product line (Microchip's Cortex-M0+ family), which spans 32 to 64 pins and 16KB to 256KB flash. The hierarchy is: microcontroller -> embedded MCU -> ARM Cortex-M MCU -> Cortex-M0+ MCU -> SAM D20 family -> SAM D20J series (64-pin, larger memory) -> ATSAMD20J17A-ANT. Key differentiating features include the Event System inter-peripheral signaling fabric, six SERCOM channels (each configurable as UART, SPI, or I2C), full-speed USB device support on select SAM D20J pins, a 12-bit 350ksps ADC with up to 20 channels, and hardware crypto is not present at this tier. Pin migration paths exist between ATSAMD20J14, J15, J16, J17, and J18 variants, allowing upward memory scaling within the same 64-pin TQFP footprint. Architecturally, the device pairs the Cortex-M0+ core (achieving 2.14 CoreMark/MHz) with a low-power segmented power domain architecture that supports Sleep, Standby, Backup, and Off modes. The integrated 32.768 kHz oscillator and digital Frequency-Locked Loop (DFLL) allow the CPU to run from internal references without external crystals in cost-sensitive applications. Typical applications include home automation nodes, consumer appliances, smart metering endpoints, industrial sensor hubs, and low-cost USB HID peripherals. Its combination of Cortex-M0+ simplicity and SAM D20 peripheral set suits battery-powered IoT edge nodes where deterministic response to peripheral events is required. When designing in this part, pay attention to the decoupling network (one 100nF + one 4.7uF near each VDD pin pair), ensure the NRST reset circuit uses the recommended 10k pull-up with the optional 1nF capacitor, and confirm that your toolchain supports the Cortex-M0+ instruction set. ATSAM-ICE or J-Link debug probes are recommended for development. This page synthesizes distributor stock and pricing, verified drop-in same-package alternatives from Microchip's SAM D20 family, and practical design guidance not collected in a single place on the manufacturer datasheet.

Cotação Contato
ATSAMD20J17A-AU - 48MHz Cortex-M0+ MCU, 128KB Flash | Microchip
ATSAMD20J17A-AU

ATSAMD20J17A-AU - 48MHz Cortex-M0+ MCU, 128KB Flash | Microchip

The Microchip Technology ATSAMD20J17A-AU is a 32-bit ARM Cortex-M0+ based microcontroller (MCU) from the SAM D20 family, operating at up to 48 MHz with 128 KB of Flash and 16 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package. It integrates a Serial Communication Interface (SERCOM) module configurable as UART/USART/SPI/I2C, a 12-bit ADC, 10-bit DAC, and full-speed USB 2.0 device support. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals on one silicon die. The Cortex-M0+ is the smallest, lowest-power ARM core, optimized for energy-efficient embedded designs. Within Microchip's portfolio, the SAM D20 family sits between the 8-bit PIC/AVR families and the higher-end Cortex-M4 SAM D5x/E5x families, balancing deterministic real-time performance with very low active and sleep current consumption. Key features of the ATSAMD20J17A-AU include the Cortex-M0+ core with single-cycle I/O access and hardware multiplier, the SERCOM peripheral block (six instances, each reconfigurable to multiple protocols), a 12-bit 350 ksps ADC with up to 20 channels, a 10-bit 350 ksps DAC, two analog comparators, and a Real-Time Clock (RTC) with calendar mode. The device supports 1.62 V to 3.63 V supply and six flexible low-power sleep modes (IDLE, STANDBY, BACKUP, OFF), achieving current consumption as low as a few microamperes in BACKUP mode with RTC running. Architecturally, the SAM D20 uses a single AHB-Lite bus matrix, a separate low-power APB bridge, and a Peripheral Event System that lets peripherals trigger one another without CPU involvement, reducing wake latency. The integrated Full-Speed USB 2.0 device controller with on-chip transceiver eliminates the need for an external PHY, simplifying USB-equipped designs. The 128 KB Flash is ECC-protected and supports in-application programming (IAP) through the bootloader ROM. Typical applications include low-power IoT sensor nodes, smart home and home automation devices, consumer electronics (wearables, toys, appliances), industrial metering and HVAC controllers, and human-machine interface (HMI) modules. The combination of USB, ADC, DAC, and flexible SERCOM makes it well-suited as a single-chip solution for tethered peripherals, small appliances, and connected sensor hubs. When designing with the ATSAMD20J17A-AU, pay close attention to decoupling (place a 100 nF X7R plus 4.7 uF bulk capacitor close to VDDIN and VDDIO), provide a stable VDDCORE voltage using the internal regulator, and route the 48 MHz crystal traces symmetrically with a ground guard ring for low-EMI performance. Microchip's Atmel Studio 7 / MPLAB X IDE with the START code configurator shortens firmware development time significantly. This page synthesizes distributor pricing, drop-in alternatives from Microchip's SAM D20 and SAM D21 families, and practical design notes not found in the standalone manufacturer datasheet.

Cotação Contato
ATSAMD20J17A-AUT - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD20J17A-AUT

ATSAMD20J17A-AUT - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology ATSAMD20J17A-AUT is an ARM Cortex-M0+ based 32-bit microcontroller from the SAM D20J family, delivering 48MHz CPU performance with 128KB Flash and 16KB SRAM in a 64-pin TQFP (10x10mm) package with exposed pad. It integrates a 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), and a full-speed USB 2.0 device interface, all while consuming low active and sleep currents typical of the SAM D20 family. What is a Cortex-M0+ microcontroller? It is a 32-bit ARM processor core optimized for the smallest die size, lowest power, and simplest programmer's model in the ARMv6-M architecture family. The Cortex-M0+ sits below Cortex-M3/M4/M7 in performance and above 8-bit legacy cores like 8051 and AVR in capability, and is widely used in cost-sensitive IoT, sensor hubs, and battery-powered consumer devices. Microcontrollers of this class integrate flash, SRAM, peripherals, and a voltage regulator into a single chip, removing the need for an external memory bus. Key features of the ATSAMD20J17A-AUT include: up to 48MHz operation from a 1.62V to 3.63V supply, six SERCOM (serial communication) interfaces that can each be configured as UART, SPI, or I2C, a 12-bit 350ksps ADC with up to 20 channels, a 10-bit 350ksps DAC, six 16-bit timer/counters, a Real-Time Clock (RTC), and full-speed USB device with on-chip transceiver. The integrated Peripheral Touch Controller supports button, slider, and wheel capacitive touch sensing without external ICs, which is unusual for MCUs in this price bracket. The device uses a single 32.768kHz crystal or internal 32kHz oscillator for low-power RTC operation, an 8MHz internal oscillator as the default system clock source, and offers multiple low-power modes (IDLE, STANDBY, BACKUP) where quiescent current drops below a few microamps. The Event System and Peripheral Event Controller allow peripherals to trigger each other without CPU intervention, enabling deterministic low-latency response and CPU-offload. Typical applications include home automation nodes, smart metering endpoints, industrial sensor transmitters, consumer wearables, USB HID/CDC devices, and capacitive touch user interfaces. The exposed thermal pad on the 64-TQFP provides a low-impedance ground bond for higher-current USB and ADC designs, while the wide supply range supports both 3.3V and 1.8V system rails. Design consideration: when using the ADC, place a 100nF decoupling capacitor adjacent to each ADC channel pin and route analog traces away from switching nodes. For USB applications, the on-chip pull-up resistor on D+ must be enabled in firmware, and the 48MHz system clock must be locked to the DFLL or a crystal reference to meet USB timing tolerance. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and design considerations not found in the manufacturer datasheet alone, providing engineers a single reference for component evaluation.

Cotação Contato
ATSAMD20J17A-CN - ARM Cortex-M0+ 48MHz MCU 128KB Flash | Microchip
ATSAMD20J17A-CN

ATSAMD20J17A-CN - ARM Cortex-M0+ 48MHz MCU 128KB Flash | Microchip

The Microchip ATSAMD20J17A-CN is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, delivering up to 48 MHz CPU clock speed with 128 KB of Flash program memory and 16 KB of SRAM, housed in a 64-ball UFBGA (5x5 mm) surface-mount package. Operating from 1.62 V to 3.6 V, the device integrates a 12-bit ADC, 10-bit DAC, 256-channel peripheral touch controller (PTC), and a full set of serial interfaces including I2C, SPI, and UART/USART. An MCU (microcontroller) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripherals such as timers, ADCs, and communication interfaces. The SAM D20J family sits within Microchip's broader portfolio of ARM Cortex-M based microcontrollers > 32-bit MCUs > embedded processors, targeting low-power, high-performance applications. The Cortex-M0+ core is the smallest and most energy-efficient ARM processor, optimized for deterministic interrupt response and minimal active/idle current. Key features include the SAM D20J's signature low-power architecture with multiple sleep modes and a power consumption profile below 100 uA/MHz active, integrated 12-bit 1 MSPS ADC with up to 16 channels, a 10-bit DAC for analog signal generation, and a 256-channel peripheral touch controller for capacitive user interfaces. The device includes a 32-bit RTC, six SERCOM modules configurable as USART/SPI/TWI, six 16-bit timers/counters, and a full-speed USB 2.0 device interface. Architecturally, the ATSAMD20J17A-CN uses Microchip's event system for hardware-level peripheral interconnect without CPU intervention, reducing latency and current consumption. The Cortex-M0+ core implements ARMv6-M Thumb/Thumb-2 instruction set, NVIC for interrupts, and a single-cycle hardware multiplier. The integrated voltage regulator, brown-out detector, and POR circuit ensure robust operation across the full 1.62-3.6 V range. Typical applications include home automation gateways, consumer electronics, smart metering, IoT sensor nodes, and industrial control peripherals such as HMI panels and motor drive signal conditioning. The wide voltage range and low-power sleep modes specifically target battery-powered edge devices. When designing with this device, evaluate power budget carefully: the integrated voltage regulator consumes a quiescent current even in standby, so for sub-1 uA sleep applications, consider the SAML21 family instead. Choose the UFBGA-64 package only when board space is critical; otherwise the QFN-64 variant improves thermal performance and reworkability. This page synthesizes distributor pricing, drop-in SAM D20J family alternatives, and practical design notes not found in the manufacturer datasheet.

Cotação Contato
ATSAMD20J17A-CNT - ARM Cortex-M0+ 48MHz MCU 128KB Flash | Microchip
ATSAMD20J17A-CNT

ATSAMD20J17A-CNT - ARM Cortex-M0+ 48MHz MCU 128KB Flash | Microchip

The Microchip ATSAMD20J17A-CNT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20J family, operating at up to 48 MHz with 128 KB of Flash program memory and 16 KB of SRAM, housed in a 64-ball UFBGA (5x5 mm) package. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals. The ARM Cortex-M0+ is the most energy-efficient member of the ARM Cortex-M family, designed for low-power embedded applications while providing Thumb-2 instruction-set efficiency and a deterministic nested-vector interrupt controller (NVIC). The ATSAMD20 sits in the hierarchy MCU -> microcontroller -> ARM Cortex-M0+ -> SAM D20 family -> semiconductor, and is purpose-built for always-on and battery-powered products. Key features include up to 48 MHz core clock, 128 KB Flash, 16 KB SRAM, a 12-bit 1 Msps SAR ADC, a 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), SERCOM-configurable serial interfaces (I2C, SPI, UART), full-speed USB 2.0 device, a Real-Time Clock (RTC), and a 16-bit Event System. The part operates from 1.62 V to 3.63 V across an industrial -40C to +105C temperature range. The ATSAMD20J17A-CNT uses Microchip's proprietary low-power technology with multiple Sleep, Standby, and Backup modes and an integrated 8 MHz DFLL (Digital Frequency Locked Loop) that can be referenced against a 32.768 kHz crystal, eliminating the need for an external high-frequency oscillator in most designs. Typical applications include home automation, smart metering, consumer electronics, industrial sensor nodes, low-power wireless platforms, capacitive-touch user interfaces, and small USB peripherals. The 64-ball UFBGA package is well-suited to compact handheld designs where board area is at a premium. Design consideration: route the SERCOM pins carefully and assign peripheral functions during firmware configuration, since SERCOM modules are multiplexed to multiple pin positions. Decouple VDD and VDDCORE with at least one 100 nF X7R ceramic capacitor placed within 3 mm of each supply pin. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster BOM selection and design-in decisions.

Cotação Contato
ATSAMD20J17A-CU - 128KB Flash Cortex-M0+ MCU | Microchip
ATSAMD20J17A-CU

ATSAMD20J17A-CU - 128KB Flash Cortex-M0+ MCU | Microchip

The Microchip ATSAMD20J17A-CU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, offering 128KB of Flash and 16KB of SRAM, packaged in a 64-ball UFBGA (5x5 mm). It supports a maximum CPU clock of 48 MHz delivering 2.14 CoreMark/MHz, with an operating voltage range of 1.6V to 3.6V and an industrial-grade temperature range up to +85C. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, peripherals, and I/O on a single die. The Cortex-M0+ class is the most area- and cost-optimized ARM core, designed for energy-efficient embedded applications while retaining the ARM Thumb-2 instruction set and a full Cortex-M ecosystem (CMSIS, vendor toolchains). Microcontrollers sit at the bottom of the embedded hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. Key features include up to 52 programmable I/O pins, a 12-bit ADC with up to 20 channels, a 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), an RTC with calendar mode, full-speed USB device, SERCOM serial interfaces (up to 6), and an Event System for hardware inter-peripheral signaling. The device also integrates an 8-channel DMA, brown-out detection, and multiple sleep modes for low-power operation. The SAM D20 architecture pairs an ARM Cortex-M0+ core (single-cycle multiplier, NVIC) with a multi-layer AHB/APB bus matrix, allowing deterministic peripheral access. Microchip's Atmel Studio/Microchip Studio and ASF/MPLAB Harmony frameworks, plus SEGGER J-Link support, give the part a mature firmware ecosystem. Sleep currents in the microamp range make it well suited for battery-powered designs. Typical applications include home automation, consumer electronics, smart metering, industrial control nodes, and low-power wireless sensor hubs. The 64-ball BGA package enables compact board layouts for wearables and IoT end nodes. When designing with this part, confirm PCB land pattern compatibility for the 5x5 mm 64-ball UFBGA and verify decoupling per the SAM D20 datasheet. Use a 32.768 kHz crystal only if RTC accuracy requires it; otherwise the internal 48 MHz DFLL is sufficient. Configure unused I/O as outputs with low state to minimize leakage. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
ATSAMD20J17A-CUT - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD20J17A-CUT

ATSAMD20J17A-CUT - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology (formerly Atmel) ATSAMD20J17A-CUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family with 128 KB Flash, 16 KB SRAM, and a maximum CPU clock of 48 MHz, packaged in a 64-ball UFBGA (5x5 mm). It operates from 1.62 V to 3.63 V and is rated for the industrial temperature range of -40C to +85C, suiting industrial, metering, home automation, and consumer applications. The part suffix CUT denotes a 64-UFBGA industrial-grade Tape & Reel variant. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (ADC, timers, communication interfaces, GPIO). The SAM D20 family sits inside the broader hierarchy of ARM Cortex-M0+ based microcontrollers -> 32-bit microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. By using the Cortex-M0+ core, the ATSAMD20J17A-CUT delivers 2.14 CoreMark/MHz while preserving the energy efficiency required for battery-powered end nodes. Key features include the Cortex-M0+ core with single-cycle I/O access, a 12-bit 350 ksps ADC, a 10-bit DAC, up to 6 SERCOM serial communication interfaces, a 24-channel event system, a Real-Time Clock (RTC), and a 256-channel Peripheral Touch Controller (PTC). The device also integrates an 8-channel DMA, a 32-bit hardware divider, and an on-chip 32 kHz RTC oscillator with PLL for the 48 MHz system clock. Sleep current is in the microampere range, with multiple low-power modes (IDLE, STANDBY, BACKUP) selectable per peripheral. The 64-UFBGA package supports up to 52 GPIO with 5 V tolerant inputs on most pins, plus dedicated I/O for USB, I2C, SPI, and UART through the flexible SERCOM peripheral. The 5x5 mm BGA footprint is intended for space-constrained designs where a QFP would be too large but the application still requires substantial memory and peripheral counts. The device is fully supported by Microchip/Atmel Studio, MPLAB X IDE, and Atmel START code-generator, with a free ASF (Atmel Software Framework) and Harmony 3 drivers. Typical applications include low-power IoT sensor nodes, smart meters, home automation gateways, industrial control, human-machine interface (HMI), and consumer wearables. The wide supply range and integrated 12-bit ADC also make it a strong fit for battery monitoring and analog front-end (AFE) interfaces. When designing with this part, ensure the four required decoupling capacitors (one 100 nF per VDD pin group) are placed as close as possible to the IC. For low-power RTC backup from a coin cell, route VBAT through a decoupling network and tie the XIN/XOUT 32.768 kHz crystal traces with short, guarded routing to minimize load capacitance error. This page synthesizes distributor pricing, drop-in package-compatible alternatives from the same SAM D20 family, and practical design notes not found in the manufacturer datasheet alone, giving procurement and engineering teams a single reference for sourcing decisions.

Cotação Contato
ATSAMD20J17A-MNT - ARM Cortex-M0+ MCU 128KB Flash 64-QFN | Microchip
ATSAMD20J17A-MNT

ATSAMD20J17A-MNT - ARM Cortex-M0+ MCU 128KB Flash 64-QFN | Microchip

The Microchip ATSAMD20J17A-MNT is a 32-bit ARM Cortex-M0+ flash MCU from the SAM D20J family, integrating 128KB of Flash and 16KB of SRAM, operating up to 48MHz, and housed in a 64-pin QFN (9x9 mm) package with an exposed thermal pad. The device runs from a 1.62V to 3.6V supply, supporting the typical 1.8V, 2.5V, and 3.3V rails common in low-power embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals such as ADC, DAC, timers, communication interfaces, and GPIO. The Cortex-M0+ is ARM's smallest and most energy-efficient core, designed for deterministic real-time response at very low active and sleep currents, which positions the SAM D20 family at the bottom of the ARM Cortex-M hierarchy (Cortex-M0+ -> Cortex-M0 -> Cortex-M3/M4 -> Cortex-M7) within the broader embedded microcontroller taxonomy (microcontroller -> semiconductor -> integrated circuit). Key features of the ATSAMD20J17A-MNT include the SAM D20J peripheral set: a 12-bit ADC up to 1 MSPS with up to 20 channels, a 10-bit 350 kSPS DAC, six SERCOM (serial communication) channels configurable as UART, SPI, or I2C, a 24-bit timer/counter for control, an RTC with calendar mode, and a 256-channel Peripheral Touch Controller (PTC) supporting capacitive touch buttons, sliders, and proximity sensing without external components. Architecturally, the device uses a single-cycle hardware multiplier, NVIC with 4 priority levels, and a low-power SleepWalking peripheral event system that allows peripherals to wake the CPU only when meaningful work is needed. The 2.14 CoreMark/MHz efficiency reflects the Cortex-M0+ Thumb-2 instruction set tuned for code density and deterministic interrupt latency under 12 cycles. Typical applications include home automation nodes, smart metering, low-power wireless sensor hubs, consumer electronics HMI with capacitive touch, industrial sensor transmitters, and battery-powered IoT endpoints where sleep current in the microampere range is critical. The wide 1.62V to 3.6V supply range lets it run directly from a single lithium coin cell or a 2xAA alkaline pack. When designing with this part, pay attention to decoupling: place a 100nF X7R ceramic on each VDD pin and a bulk 4.7uF near the package, route the exposed pad (EP) to a continuous ground copper pour with at least 4 thermal vias to the inner ground plane for low-impedance thermal and electrical return. Configure unused pins as outputs with low state or enable the internal pull-down to minimize leakage in battery-powered designs.

Cotação Contato
ATSAMD20J18A-AU - ARM Cortex-M0+ MCU, 256KB Flash | Microchip
ATSAMD20J18A-AU

ATSAMD20J18A-AU - ARM Cortex-M0+ MCU, 256KB Flash | Microchip

The Microchip Technology ATSAMD20J18A-AU is an ARM Cortex-M0+ based 32-bit flash microcontroller delivering 256KB of flash and 32KB of SRAM in a 64-pin LQFP package, running at up to 48 MHz. It targets low-power, high-performance home automation, consumer, metering, and industrial applications with a wide operating voltage range and a rich peripheral set including up to 52 programmable I/O pins. An ARM Cortex-M0+ microcontroller is a 32-bit processor core implementing the ARMv6-M architecture (Thumb/Thumb-2 instruction set), optimized for energy-efficient embedded computing. Cortex-M0+ sits at the low-power end of the Cortex-M family above M0L/M23 and below M3/M4/M7, and integrates tightly with on-chip flash, SRAM, and peripherals to form a system-on-chip (SoC) within the broader microcontroller and embedded processing hierarchy. Key features include a 12-bit ADC up to 200 ksps, 10-bit DAC, up to 8 SERCOM interfaces that can each be configured as UART, SPI, I2C, or LIN, a 24-bit timer/counter, RTC, full-speed USB device, and 2.4mA/MHz active current with multiple Sleep, Standby, and Backup sleep modes that drop consumption into the microamp range. Six SERCOM channels, six timer/counters, and an I2S interface provide flexible connectivity for sensors, displays, and communications. Technically, the device integrates a single-cycle multiplier, 4KB cache, and a 2-channel DMA engine for low-overhead peripheral transfers. The architecture is well documented in the SAM D20 family datasheet and is supported by Microchip's MPLAB X IDE, ASF, and Atmel Studio 7 toolchains, with a choice of GCC or IAR compilers. A built-in 32.768 kHz oscillator and an on-chip PLL simplify clocking for USB and high-speed peripherals. Typical applications include home-automation gateways, smart energy metering, industrial sensor nodes, consumer HMI controls, low-power wireless sensor nodes, and USB human-interface devices. The wide 1.62V to 3.6V supply range and ultra-low-power Sleep modes also support battery-powered IoT endpoints. When designing with this device, ensure that the decoupling network (typically 100nF plus 4.7uF bulk) is placed within a few millimeters of the VDD pins, and that PA24/PA25 (USB) and PA22/PA23 are configured correctly for full-speed USB if the D+ pull-up is needed. Pay attention to the SERCOM pin-mux table: each SERCOM can be mapped to several I/O pins, but only one mapping at a time is active. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes that are not always assembled in a single location elsewhere.

Cotação Contato
ATSAMD20J18A-AUES - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip
ATSAMD20J18A-AUES

ATSAMD20J18A-AUES - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip

The Microchip Technology ATSAMD20J18A-AUES is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20J family, operating at up to 48 MHz with 256 KB of Flash and 32 KB of SRAM in a 64-pin TQFP (10x10 mm) exposed-pad package. It integrates a 12-bit ADC, 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), and a full SERCOM peripheral set for flexible serial communication. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripherals. ARM Cortex-M0+ cores target low-power, deterministic embedded applications; the SAM D20J extends this with Microchip's peripheral ecosystem including Event System and SleepWalking. The device sits within the hierarchy: Cortex-M0+ MCU -> ARM Cortex-M microcontroller -> embedded MCU -> semiconductor. Key features include a 1.62 V to 3.6 V supply range, six SERCOM channels configurable as UART/SPI/I2C, USB device support via embedded FS USB, hardware CRC, a 32-bit Real-Time Clock with calendar, and low-power modes down to microamp standby current. The integrated PTC supports capacitive touch sensing without external components, while the 12-bit ADC delivers up to 300 ksps with up to 20 channels. The SAM D20J uses a Harvard-bus architecture with single-cycle IO and a 4-channel DMA controller that offloads CPU data movement. The Event System allows peripherals to trigger each other without CPU intervention, while SleepWalking peripherals wake the CPU only when needed, reducing average power in sensor-driven applications. Typical applications include home automation and IoT nodes, capacitive-touch human-machine interfaces, smart meters and sensor hubs, industrial control peripherals, and low-power wireless sensor platforms. The wide memory and rich peripheral mix allow consolidation of multiple functions into a single MCU. When designing with this device, allocate the 10x10 mm TQFP exposed pad properly to the ground plane for thermal and signal-integrity performance. Use Atmel/Microchip Studio with ASF or start.atmel.com (MCC) code generation to accelerate firmware development and SERCOM configuration. This page synthesizes distributor pricing, verified same-family drop-in alternatives, and PCB-level design notes not found in the manufacturer datasheet alone, helping engineers select and qualify the ATSAMD20J18A-AUES for production.

Cotação Contato
ATSAMD20J18A-AUT - ARM Cortex-M0+ 48MHz 256KB Flash MCU | Microchip
ATSAMD20J18A-AUT

ATSAMD20J18A-AUT - ARM Cortex-M0+ 48MHz 256KB Flash MCU | Microchip

The Microchip Technology ATSAMD20J18A-AUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, delivering up to 48 MHz CPU clock speed, 256 KB of embedded Flash, and 32 KB of SRAM in a 64-pin LQFP (10x10 mm) package. The -AUT suffix indicates an industrial temperature grade (-40C to +85C) and Tape & Reel packaging for high-volume SMT assembly. Microcontrollers (MCUs) are programmable system-on-chip devices that integrate a processor core, volatile and non-volatile memory, and a rich peripheral set into a single package. The ARM Cortex-M0+ is one of the smallest and most energy-efficient 32-bit cores in the ARM family, designed for deterministic embedded control. The ATSAMD20J18A-AUT sits in the SAM D20 family, Microchip's mainstream low-power Cortex-M0+ MCU line, hierarchically positioned above 8-bit AVR/PIC devices and below Cortex-M4 parts such as the SAM D5x/E5x. Key features include the 2.14 CoreMark/MHz performance figure, a 6-channel SERCOM (configurable as UART, SPI, or I2C) interface, a 12-bit ADC, 10-bit DAC, and full-speed USB device capability on selected pins. The Event System, SleepWalking peripherals, and multiple low-power sleep modes allow the device to keep waking intelligently while consuming minimal current - well suited to battery-powered edge nodes. The architecture pairs a single-cycle hardware multiplier with a 4-channel direct memory access controller, enabling efficient peripheral-to-memory transfers without CPU intervention. The integrated high-speed 48 MHz on-chip oscillator (DFLL-fine locked to the internal 32 kHz source) provides factory-calibrated accuracy without an external crystal, lowering BOM cost. Typical applications include home automation nodes, smart metering endpoints, consumer wearables, building control sensors, and industrial sensor hubs. Within a system, the ATSAMD20J18A-AUT often acts as the main controller handling analogue signal conditioning, communication, and user-interface tasks. With its Cortex-M0+ ISA, code is portable to the wider SAM D / SAM C / SAM S family lineup with minimal rework. For designers, the most useful planning step is reserving 4 KB of Flash for a future bootloader, leaving adequate decoupling (100 nF + 1uF) close to each VDD pin, and confirming the chosen package variant's pin count (this is the 64-pin LQFP) against the I/O requirement before layout. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical engineering notes not found in the manufacturer datasheet alone.

Cotação Contato
ATSAMD20J18A-CN - ARM Cortex-M0+ MCU, 256KB Flash, 64-UFBGA
ATSAMD20J18A-CN

ATSAMD20J18A-CN - ARM Cortex-M0+ MCU, 256KB Flash, 64-UFBGA

The Microchip Technology ATSAMD20J18A-CN is a 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D20 family, delivering up to 48 MHz CPU performance with 256 KB of Flash program memory and 32 KB of SRAM in a 64-pin UFBGA package. The device operates from 1.6 V to 3.6 V and supports both industrial (-40C to +105C) temperature grades, making it suitable for harsh-environment embedded designs. What is an ARM Cortex-M0+ microcontroller? An ARM Cortex-M0+ is an ultra-low-power 32-bit processor core designed by ARM Holdings, optimized for cost-sensitive embedded applications that require deterministic real-time behavior. It sits within the hierarchy of microcontroller categories: microcontroller -> 32-bit MCU -> ARM Cortex-M microcontroller -> Cortex-M0+ class, and within the SAM D20 product line it represents the entry point to Microchip's Cortex-M0+ portfolio. Key features of the ATSAMD20J18A-CN include the integrated Peripheral Touch Controller (PTC) supporting up to 256 channels for capacitive touch interfaces, a 12-bit ADC with up to 20 channels, a 10-bit DAC, SERCOM (serial communication) modules configurable as UART/SPI/I2C, and a full-speed USB 2.0 device interface. The Event System allows inter-peripheral signaling without CPU intervention, reducing software complexity and power consumption. The architecture uses single-cycle I/O access, hardware multiplier, and Microchip's proprietary SleepWalking technology for peripheral-level clock gating. The 48 MHz Cortex-M0+ core delivers 0.93 DMIPS/MHz, sufficient for sensor fusion, motor control, and HMI applications. Typical applications include home automation control panels, smart metering endpoints, consumer appliances with capacitive touch, industrial sensor hubs, and battery-powered IoT edge nodes. The combination of low active current (~3 mA at 48 MHz), multiple low-power sleep modes, and fast wake-up time makes it suitable for energy-harvesting designs. When designing with this part, evaluate decoupling strategy carefully: place one 100 nF X7R ceramic capacitor on each VDD/VDDIO pair as close to the IC as possible, and provide a 4.7 uF bulk capacitor on the main rail. Verify I/O bank voltage compatibility - all GPIO must reference the same VDDIO rail for the bank to operate correctly. This page synthesizes distributor pricing, drop-in alternatives from the same SAM D20 family, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
ATSAMD20J18A-CU - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip
ATSAMD20J18A-CU

ATSAMD20J18A-CU - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip

The Microchip ATSAMD20J18A-CU is a 32-bit ARM Cortex-M0+ flash microcontroller operating at up to 48 MHz, equipped with 256 KB of Flash and 32 KB of SRAM, housed in a 64-ball UFBGA (5x5 mm) package. It targets low-power, high-performance embedded applications in home automation, consumer, metering, and industrial segments, reaching up to 2.46 CoreMark/MHz while consuming as little as 70 uA/MHz active and sub-uA sleep currents. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), working memory (SRAM), and a rich set of peripherals on a single die. The Cortex-M0+ class of MCUs represents the most energy-efficient tier of the ARM Cortex-M family, optimized for deterministic interrupt-driven workloads and ultra-low standby power. Within Microchip's portfolio, the ATSAMD20J18 belongs to the SAM D20 family of microcontrollers, sitting in the broader category of 32-bit flash MCUs under the Microchip SMART ARM-based product line. The part is pin-compatible across the SAM D20 series, enabling identical PCB layouts for variants with differing Flash and SRAM sizes. Key features of the ATSAMD20J18A-CU include an integrated 12-bit ADC with up to 20 channels, a 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), a full-speed USB 2.0 device interface, multiple SERCOM (serial communication) modules configurable as UART, SPI, or I2C, and a 32-bit Real-Time Clock (RTC). It also provides six 16-bit Timer/Counters, an Event System for inter-peripheral signaling without CPU intervention, and a comprehensive clock management unit with on-chip PLLs and oscillators. Architecturally, the ATSAMD20J18A-CU is built on a low-leakage CMOS process and integrates a high-performance 32-bit core with single-cycle I/O access, hardware multiply, and a Nested Vectored Interrupt Controller (NVIC). The 2.46 CoreMark/MHz figure confirms efficient Thumb-2 instruction execution, and the wide 1.62 V to 3.63 V operating range allows direct connection to single-cell Li-ion or 3.3 V regulated rails. Typical applications include low-power wireless sensor nodes, smart metering, home automation controllers, USB Human Interface Devices (HIDs), industrial control panels, and consumer electronics with capacitive touch user interfaces. The rich peripheral mix enables single-chip implementations of bridge, HMI, and data-acquisition products. Designers should plan for the SERCOM peripheral mapping during firmware architecture, since each SERCOM instance can be routed to a specific set of pads. Decoupling must include a 100 nF cap per VDD pin plus a bulk 4.7 uF capacitor placed close to the package. For USB applications, the DP/DM traces require 90 ohm differential impedance and a precision 1.0 uF USB transceiver bypass capacitor. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family and from competing Cortex-M0+ families, and practical design notes that go beyond the manufacturer datasheet to accelerate your schematic capture and PCB layout decisions.

Cotação Contato
ATSAMD20J18A-MN - ARM Cortex-M0+ MCU 256KB Flash | Microchip
ATSAMD20J18A-MN

ATSAMD20J18A-MN - ARM Cortex-M0+ MCU 256KB Flash | Microchip

The Microchip Technology ATSAMD20J18A-MN is a 32-bit ARM Cortex-M0+ based flash microcontroller delivering up to 48 MHz CPU performance with 256 KB of Flash and 32 KB of SRAM, housed in a 64-pin QFN (HVQCCN) package. It operates across a wide 1.62 V to 3.63 V supply range and is specified for the industrial temperature range of -40 C to +105 C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as ADC, timers, communication interfaces, and GPIOs. The SAM D20 family sits within Microchip's broader portfolio of ARM Cortex-M based microcontrollers -> 32-bit microcontrollers -> microcontrollers -> semiconductors, and is purpose-built for low-power embedded designs. The Cortex-M0+ core delivers 2.14 CoreMark/MHz, balancing energy efficiency with deterministic real-time response. Key features include a 12-bit ADC with up to 16 channels and 350 ksps throughput, a 10-bit DAC, six SERCOM configurable serial interfaces (each usable as UART, I2C, or SPI), a 24-channel peripheral touch controller, and a full-speed USB 2.0 device port. The Event System and SleepWalking peripherals enable deterministic peripheral wake-up while the CPU remains dormant, allowing designers to meet aggressive power budgets. The architecture combines an ultra-low-power design (down to 8 uA/MHz active, sub-microamp deep sleep) with deterministic interrupt latency from the Cortex-M0+ Nested Vector Interrupt Controller (NVIC). Integrated AES-like crypto hardware and a true random number generator (TRNG) on selected variants strengthen secure connectivity. The 64-pin QFN package exposes up to 52 GPIOs enables two I2S channels and a full-speed USB PHY. Typical applications include home automation nodes, smart metering endpoints, consumer wearables, industrial sensor hubs, and IoT edge devices that need both low standby consumption and responsive real-time behavior. The wide supply range and industrial temperature grade also suit battery-powered or outdoor deployments. When designing with this device, ensure the QFN thermal pad is soldered to a sufficiently large copper pour to meet the 64-pin HVQCCN thermal envelope. The SAM D20's SERCOM multiplexing requires careful pin mapping via the PORT controller; refer to the device pinout table before committing PCB layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotação Contato