ADF4107BRU - 7 GHz Integer-N PLL Frequency Synthesizer
N.º da peça: ADF4107BRU ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $4.57 | $4,57 |
| 10 | $4.57 | $45,70 |
| 100 | $4.57 | $457,00 |
| 500 | $4.57 | $2.285,00 |
| 1.000 | $4.57 | $4.570,00 |
ADF4107BRU Visão geral
A PLL frequency synthesizer generates a stable, programmable output frequency from a reference source. This device combines a low-noise digital phase-frequency detector, precision charge pump, programmable counters, and dual-modulus prescaler to support frequency multiplication and division. The ADF4107 family is positioned in the clock-and-timing semiconductor hierarchy, where it provides programmable RF frequency generation for communication systems.
Key features include operation up to 7 GHz, 6-bit A-counter and 13-bit B-counter programmability, and a programmable dual-modulus prescaler. The reference divider allows the reference frequency to be divided before comparison with the synthesized feedback signal. The datasheet identifies typical phase noise of -83 dBc/Hz at 1 kHz offset and spurs better than -70 dBc in the cited typical application condition.
The architecture is intended for RF signal chains where a stable reference clock and programmable feedback divider are required. The prescaler divides the output frequency, while the A and B counters determine the required multiplication ratio and modulus. Correct loop-filter design is essential because phase noise, reference spurs, lock behavior, and output jitter depend on the selected reference frequency, bandwidth, and loop parameters.
Typical applications include wireless receiver and transmitter local oscillators, upconversion and downconversion chains, RF communications equipment, and test systems requiring programmable RF signal generation. The ADF4107 is also useful where a low-cost integer-N architecture is preferable to a fractional-N synthesizer and the required channel spacing and phase-noise performance can be met.
For implementation, follow the datasheet’s recommended reference, charge-pump, filter, and decoupling connections. Keep the reference and RF paths short, use controlled impedance routing where appropriate, and account for the device’s supply voltage and grounding requirements. This page combines verified manufacturer and distributor information with practical PLL design guidance; unavailable parameters are explicitly marked rather than estimated.
Alternativas drop-in para ADF4107BRU — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ADF4107BRU (mesmo formato e footprint) — diferindo em A Counter, B Counter, Package, Prescaler, Product Type.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ADF4107BRUZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4110BRU-REEL7
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4156BRUZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4107BRU-REEL
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4107BRUZ-REEL
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4107BRU Especificações
| Product Type | Integer-N PLL frequency synthesizer |
| Maximum RF Output Frequency | 7 GHz |
| Input Frequency Range | 1 GHz to 7 GHz |
| A Counter | 6-bit programmable |
| B Counter | 13-bit programmable |
| Prescaler | Dual-modulus P/P + 1 |
| Reference Divider | Programmable |
| Charge Pump | Precision charge pump |
| Phase-Frequency Detector | Low-noise digital PFD |
| Tensão de alimentação | AVDD = DVDD = 3 V ± 10% |
| Maximum Supply Voltage | 5.5 V |
| RSET | 5.1 kΩ |
| Typical Phase Noise | -83 dBc/Hz at 1 kHz offset |
| Typical Spurs | Better than -70 dBc |
| Encapsulamento | 16-lead TSSOP, 0.173 inch width, 4.40 mm width |
| Tipo de montagem | Surface mount |
| Operating Application | Wireless receiver and transmitter local oscillators |
| Status RoHS | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
Guia de Configuração de Pinos do ADF4107BRU 16-lead tssop, 0.173 inch width, 4.40 mm width
Configuração de pinos para ADF4107BRU (pacote 16-lead tssop, 0.173 inch width, 4.40 mm width). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para ADF4107BRU.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ADF4107BRU é adequado para 6 aplicaçãos: Wireless Transmitter Local Oscillator, Wireless Receiver Local Oscillator, RF Upconversion and Downconversion, Programmable RF Test Equipment, RF Communications Module, Instrumentation and Signal Analysis.
Wireless Transmitter Local Oscillator
The ADF4107BRU fits a wireless transmitter local-oscillator position because it synthesizes programmable frequencies across the verified 1 GHz to 7 GHz range. Place it in the feedback path of the RF signal chain, where the reference divider, dual-modulus prescaler, and A/B counters establish the required multiplication ratio. The datasheet reports typical phase noise of -83 dBc/Hz at 1 kHz offset and spurs better than -70 dBc under its cited condition. Actual TX performance depends on loop bandwidth, reference quality, charge-pump settings, buffering, and PCB isolation from high-power RF stages.
Recomendado
Wireless Receiver Local Oscillator
For receiver downconversion, the ADF4107BRU provides a programmable integer-N oscillator that can drive a mixer or other RF front-end stage. Its 6-bit A counter, 13-bit B counter, programmable reference divider, and dual-modulus prescaler allow the designer to select a feedback ratio while retaining a conventional reference source. The key engineering concern is receiver phase noise and reference spur performance; use the datasheet loop-filter method, isolate the reference input, and verify temperature and aging behavior across the intended receive bands.
Recomendado
RF Upconversion and Downconversion
The ADF4107BRU is suitable for local-oscillator generation in both upconversion and downconversion sections because the manufacturer specifically identifies those wireless receiver and transmitter functions. The synthesized output can feed a mixer LO after appropriate gain and filtering stages. Designers should select the prescaler and counters so the requested frequency is reachable without excessive reference multiplication, then verify phase noise, spur levels, lock time, and output isolation. The 7 GHz ceiling leaves headroom for RF test and instrumentation chains within the verified operating band.
Recomendado
Programmable RF Test Equipment
The ADF4107BRU can provide a programmable RF source for test equipment when a controlled reference and suitable feedback network are available. Its programmable A and B counters, reference divider, and dual-modulus prescaler make it useful for automated channel and frequency sweeps. The designer must account for settling time, loop bandwidth, reference accuracy, and output buffering rather than assuming frequency programming alone guarantees fast or accurate measurements. The datasheet’s loop-filter calculations and typical phase-noise/spur data provide the starting point for system-level test planning.
Recomendado
RF Communications Module
The ADF4107BRU supports RF communications modules that require a programmable local oscillator and a stable external reference. Its integer-N structure is useful when the required channel plan and phase-noise performance are compatible with the loop design. The reference divider and counters should be programmed from the system’s reference frequency, while the loop filter should be calculated for the target channel spacing and lock behavior. PCB layout must keep the reference path and charge-pump filter compact, with grounding arranged to minimize coupling from RF and switching circuitry.
Recomendado
Instrumentation and Signal Analysis
The ADF4107BRU can serve instrumentation systems that need a programmable RF reference for excitation or conversion. The verified frequency range of 1 GHz to 7 GHz supports many RF measurement contexts, while the programmable architecture allows the system controller to select operating points through the device registers. Instrumentation designs should budget for reference purity, phase noise, spur filtering, output amplitude, and settling time. A stable low-noise reference and a carefully placed loop filter are usually more important to repeatable measurements than the nominal synthesizer frequency alone.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ADF4107BRU — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ADF4107BRUZ | ADF4110BRU-REEL7 | ADF4156BRUZ | ADF4107BRU-REEL |
|---|---|---|---|---|---|
| Package | 16-lead TSSOP | 16-lead TSSOP | 16-lead TSSOP | 16-lead TSSOP | 16-lead TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Principais diferenciais
- Direct integer-N RF synthesis solution (vs ADF4107BRUZ)
- Programmable dual-modulus feedback architecture (vs ADF4107BRU-REEL)
- RF coverage for wireless signal chains (vs ADF4156BRUZ)
Notas de projeto
Use the verified supply arrangement of AVDD = DVDD = 3 V ± 10%, while keeping the maximum supply voltage at or below 5.5 V. Place decoupling capacitors close to the supply pins and provide a clean return path. Because PLL phase noise can be affected by supply ripple and digital coupling, evaluate the power tree with the actual reference, charge-pump, and RF-output operating conditions rather than relying only on the nominal voltage.
Keep the reference input and charge-pump loop-filter traces short and isolated from the RF feedback path and switching nodes. The manufacturer datasheet uses its specifications and loop-filter equations to derive component values; those values depend on reference frequency, PFD frequency, target bandwidth, phase noise, and charge-pump settings. Place the loop-filter components at the intended IC pins and avoid routing sensitive nodes beneath high-current or high-frequency RF traces.
Do not assume that every ADF4107-family order code is automatically interchangeable. Check the exact package, pinout, counter widths, reference-divider range, PFD and charge-pump behavior, supply limits, temperature range, and register map. The verified cross-reference data names ADF4107BRUZ and related ADF4107 variants, but it does not provide enough information to certify every listed candidate as a universal drop-in replacement.
Informações de conformidade
The supplied verified data does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for ADF4107BRU. AEC-Q100 is marked not_applicable because no automotive qualification claim is present.
