ADF4360-7BCP - 350-1800 MHz Integer-N Synthesizer | Analog Devices
N.º da peça: ADF4360-7BCP ✓ AtivoADF4360-7BCP Visão geral
An integer-N synthesizer is a phase-locked-loop frequency generator that combines a digitally controlled frequency divider, phase detector, charge pump, reference divider, and voltage-controlled oscillator. The ADF4360-7 integrates the synthesizer and VCO into one RF IC, while external inductors establish the required RF resonance and frequency range. This places the device within the hierarchy of RF synthesizer, PLL frequency generator, clock and timing IC, and semiconductor.
Principal features include an integer-N architecture, a three-wire serial interface, programmable output power, digital lock detection, and hardware and software power-down modes. The 350 MHz to 1800 MHz operating range covers radio, communications, instrumentation, and test-equipment frequency plans. Its divide-by-2 function extends the design flexibility by producing 175 MHz to 900 MHz outputs when a lower divided frequency is required.
The internal feedback divider permits integer-N frequency synthesis from the external reference, while the integrated VCO removes the need for a separate discrete oscillator in suitable designs. A 3.6 V supply supports the RF core, and 1.8 V-compatible interfacing allows connection to modern control logic. The three-wire serial interface provides a compact path for register configuration, output-power adjustment, and operating-mode control.
Typical uses include wireless transceiver local oscillator generation, radio-frequency test equipment, frequency-generation modules, and communication equipment requiring programmable RF outputs. Designers can also use the device in measurement systems that need an integrated synthesizer and VCO with selectable output power and lock-status feedback.
PCB implementation should preserve short RF paths and a controlled ground plane around the exposed pad. Place the VCO inductors and associated decoupling components close to the relevant device pins, and route the serial interface away from sensitive RF nodes. Validate lock behavior, unwanted harmonics, and supply-noise sensitivity on the assembled board because RF layout and component selection strongly influence final performance.
This product page combines the manufacturer's frequency-range and interface details with pin-compatible family options, comparison data, and practical RF layout guidance. It is intended to help engineers identify whether the ADF4360-7BCP matches a required tuning range, package, and control interface before beginning PCB implementation.
Alternativas drop-in para ADF4360-7BCP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ADF4360-7BCP (mesmo formato e footprint) — diferindo em Package, Product Type, Serial Interface.
ADF4360-7BCPZ
✅ Drop-InConsulte o preço
Ver ficha técnica →ADF4360-7BCPZRL
✅ Drop-InConsulte o preço
Ver ficha técnica →ADF4360-3BCPZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4360-4BCPZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4360-0
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADF4360-7BCP Especificações
| Product Type | Integrated integer-N frequency synthesizer and voltage-controlled oscillator |
| Center Frequency Range | 350 MHz to 1800 MHz |
| Divide-by-2 Output Frequency Range | 175 MHz to 900 MHz |
| Power Supply Voltage | 3.6 V |
| Logic Compatibility | 1.8 V |
| Synthesizer Architecture | Integer-N |
| Output Power | Programmable |
| Serial Interface | 3-wire serial interface |
| Lock Detection | Digital |
| Power-Down Modes | Hardware and software |
| VCO Frequency Setting | Set by external inductors |
| Encapsulamento | 24-lead LFCSP with exposed pad |
| Tipo de montagem | Surface mount |
| Maximum Output Frequency | 1800 MHz |
| Minimum Output Frequency | 350 MHz |
Guia de Configuração de Pinos do ADF4360-7BCP 24-lead lfcsp with exposed pad
Configuração de pinos para ADF4360-7BCP (pacote 24-lead lfcsp with exposed pad). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para ADF4360-7BCP.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ADF4360-7BCP é adequado para 6 aplicaçãos: Wireless Transceiver Local Oscillator, Programmable RF Signal Source, Radio-Frequency Test Equipment, Communication Module Frequency Generation, Frequency Generator Instrumentation, RF Transceiver Support Circuit.
Wireless Transceiver Local Oscillator
The ADF4360-7BCP fits a wireless transceiver local-oscillator position requiring programmable RF generation across 350 MHz to 1800 MHz. Its integrated integer-N synthesizer and VCO consolidate frequency generation into the 24-lead LFCSP device, while the three-wire serial interface allows a host controller to configure the operating frequency and output power. The digital lock-detect function can also feed system sequencing logic. Designers should account for the 3.6 V supply and 1.8 V-compatible logic, then place the external VCO inductors and decoupling components close to the RF pins to preserve predictable performance.
Recomendado
Programmable RF Signal Source
The ADF4360-7BCP can serve as the core of a programmable RF signal source for laboratory and production equipment. Its 350 MHz to 1800 MHz range allows the same synthesizer platform to cover numerous RF test points, and the divide-by-2 mode provides 175 MHz to 900 MHz outputs when divided operation is useful. Programmable output power supports different downstream test levels, while digital lock detection indicates whether the loop has acquired lock. The implementation should use short RF routes, a stable reference, and the external inductors recommended in the manufacturer design guidance.
Recomendado
Radio-Frequency Test Equipment
The ADF4360-7BCP is appropriate for RF test equipment that generates repeatable local-oscillator or reference tones. The integer-N architecture provides a single-chip frequency synthesizer and VCO, reducing the number of separate RF building blocks required for an instrument. Its programmable output level can accommodate different measurement paths, and the lock-detect output helps a controller distinguish an unlocked condition from a valid RF state. For production instruments, pay particular attention to reference-jitter sensitivity, loop-filter components, harmonic content, and board-level thermal behavior during repeated frequency changes.
Recomendado
Communication Module Frequency Generation
The ADF4360-7BCP supports communication modules that require an integrated, digitally controlled RF source within the 350 MHz to 1800 MHz band. A host processor can use the three-wire serial interface to configure the synthesizer, and the 1.8 V-compatible logic simplifies connections to compatible controllers. Hardware and software power-down modes provide additional control over operating state, while digital lock detection supports reliable system behavior. The final RF layout should isolate the VCO region from noisy digital and switching circuitry and should follow the exposed-pad land pattern prescribed for reliable thermal performance.
Recomendado
Frequency Generator Instrumentation
The ADF4360-7BCP can anchor a compact frequency-generator instrument because it integrates the integer-N synthesizer and VCO in one package. The 350 MHz to 1800 MHz range gives the instrument a broad tuning span, while divide-by-2 operation expands access to 175 MHz to 900 MHz. Programmable output power and digital lock indication make the device useful in automated test sequences controlled through its three-wire serial interface. Engineering teams should select the external inductors and loop-filter components from the reference design and evaluate phase noise and spurious performance with the final reference and enclosure configuration.
Recomendado
RF Transceiver Support Circuit
The ADF4360-7BCP is suitable for generating the local-oscillator signal used by selected RF transceivers in the 350 MHz to 1800 MHz range. Integrating the synthesizer and VCO can reduce board area compared with a discrete oscillator arrangement, while digital lock detection gives the transceiver controller a clear acquisition-status input. Its 3.6 V supply requirement must be included in the transceiver power architecture, and the external VCO inductors should be positioned according to the reference layout. Validate harmonic content, isolation, and temperature drift across the complete operating range before production release.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ADF4360-7BCP — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Use ADF4360-3BCPZ only when the complete RF plan falls within its lower 65-400 MHz range; its shared family package does not make it suitable for frequencies that exceed 400 MHz. ADF4360-4BCPZ requires confirmation of its exact frequency limits before selection. ADF4360-0 is centered near 2600 MHz and therefore favors microwave applications above the ADF4360-7 range. For every option, verify the external-inductor values, loop-filter design, reference requirements, output-power settings, and exposed-pad footprint against the manufacturer application guidance.
Comparação com alternativas
| Parâmetro | Este produto | ADF4360-7BCPZ | ADF4360-7BCPZRL | ADF4360-3BCPZ | ADF4360-4BCPZ | ADF4360-0 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad |
| Synthesizer Architecture | Integer-N | Integer-N | Integer-N | Integer-N | Integer-N | Integer-N |
Principais diferenciais
- Wider upper tuning range than the lower-band ADF4360-3BCPZ option (vs ADF4360-3BCPZ)
- Direct divide-by-2 coverage for lower-frequency RF outputs (vs ADF4360-3BCPZ)
- Closest ordering match for footprint reuse (vs ADF4360-7BCPZ)
- Target frequency range better suited to sub-2 GHz RF plans (vs ADF4360-0)
Notas de projeto
Place the external VCO inductors and their associated components close to the ADF4360-7BCP VCO pins, following the Analog Devices reference layout. Keep the RF output path short, minimize loop area, and preserve a continuous ground reference beneath the 24-lead LFCSP. Avoid routing the three-wire serial interface beneath or between sensitive RF nodes, where clock edges and supply transients could couple into the VCO region.
Implement the exposed pad as a thermal and electrical land pattern rather than treating it as an unconnected mechanical feature. Use the manufacturer's recommended footprint and thermal-via arrangement, and provide local supply decoupling with very short return paths. Review the completed PCB for adequate via current capacity and confirm that the ground reference remains continuous around the package before RF performance testing.
Do not assume that every ADF4360 family member can replace the ADF4360-7BCP solely because it uses a related package. The ADF4360-3 is identified for a 65-400 MHz range, while the ADF4360-7 supports 350-1800 MHz; the ADF4360-0 is centered near 2600 MHz. Verify the complete frequency range, divide-by-2 requirement, external-inductor values, loop filter, pin assignment, and ordering suffix before approving a family substitution.
Budget the ADF4360-7BCP's 3.6 V supply around both operating current and transient load requirements. Place decoupling capacitors at the supply pins and maintain a low-impedance return to the supply plane. The 1.8 V-compatible serial interface can simplify host-controller connections, but interface levels, signal termination, and power-sequencing relationships must be checked against the complete system timing.
Treat the reference and loop-filter components as part of the RF synthesizer rather than generic support circuitry. Use the values and layout from the manufacturer application guidance, keep the reference path away from high-energy RF nodes, and validate lock, phase noise, and spurious performance with the final reference source. The digital lock-detect output should be interpreted by the controller as acquisition feedback, not as a guarantee of acceptable RF performance.
Informações de conformidade
The ADF4360-7BCP is a general-purpose RF integrated circuit rather than an AEC-Q100-qualified automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.