ADM206ARSZ - 4/3 RS-232 Transceiver | Analog Devices
N.º da peça: ADM206ARSZ ✓ AtivoADM206ARSZ Visão geral
An RS-232 transceiver is an interface IC that converts between digital logic levels and the voltage levels used by RS-232 links. It belongs to the line-driver and line-receiver family, combines transmitter and receiver functions in one package, and is used where legacy equipment or industrial peripherals require robust serial communication over several meters. The ADM206 family is designed for EIA-232-E and V.28 interfaces when a ±12 V supply is unavailable.
Key features include four RS-232 drivers, three RS-232 receivers, a shutdown pin, an enable pin, and operation from a single +5 V supply. The integrated DC-to-DC converters generate the bipolar voltage levels required by RS-232 transmitters. This approach simplifies system power design because the circuit does not require a separate negative supply rail. The 24-SSOP package also reduces board area compared with larger leaded transceiver packages.
The transceiver architecture separates transmit and receive signal paths while allowing unused receivers to remain active during shutdown. Logic-level enable and shutdown controls support systems that need to isolate, reset, or reduce power consumption in the interface section. The manufacturer describes the ADM206 family as suitable for EIA-232-E and V.28 communications interfaces, particularly where a 12 V supply is not available.
Typical applications include industrial serial-port adapters, instrumentation links, data acquisition systems, test equipment, embedded-control peripherals, and legacy computer equipment. Four driver channels can support multiple outgoing RS-232 signals, while three receiver channels suit interfaces with fewer inbound signals. Its integrated charge-pump support makes it especially useful where PCB area and external component count are important.
The main design consideration is charge-pump capacitor placement. Follow the manufacturer’s polarity and capacitance requirements for the 0.1 µF capacitors and keep the associated traces short. Because the device generates high-voltage RS-232 signals from a 5 V rail, care is also needed to protect adjacent low-level circuitry from ESD events and to maintain suitable signal-return paths on long cables.
This page combines the manufacturer’s functional description with package, interface, sourcing, replacement, and design guidance. It also distinguishes verified same-package drop-in options from functionally similar devices that require a different footprint, helping engineers avoid PCB redesigns and unintended interface incompatibilities.
Alternativas drop-in para ADM206ARSZ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasADM206ARSZ Especificações
| Product Type | RS-232 transceiver |
| Number of Drivers | 4 |
| Number of Receivers | 3 |
| Tensão de alimentação | +5 V |
| Maximum Data Rate | 200 kbps |
| Charge-Pump Capacitor Value | 0.1 µF |
| On-Board Converter Output Swing | ±9 V |
| Low Power | 15 mW |
| Protocol | RS-232 |
| Interface Standard Support | EIA-232-E and V.28 |
| Encapsulamento | 24-SSOP, 5.30 mm width |
| Tipo de montagem | Surface mount |
| Shutdown Control | Yes |
| Enable Control | Yes |
Guia de Configuração de Pinos do ADM206ARSZ 24-ssop, 5.30 mm width
Configuração de pinos para ADM206ARSZ (pacote 24-ssop, 5.30 mm width). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para ADM206ARSZ.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ADM206ARSZ é adequado para 6 aplicaçãos: Industrial Serial-Port Interface, Data-Acquisition Equipment, Test and Measurement Systems, Embedded Control Peripherals, Legacy Computer Peripherals, Remote Monitoring and Control.
Industrial Serial-Port Interface
The ADM206ARSZ fits industrial adapters that need multiple RS-232 channels but only a 5 V power rail. Its four drivers and three receivers provide useful channel balance for command, status, and data paths, while the 200 kbps maximum data rate supports moderate-speed equipment links. The integrated converters produce approximately ±9 V from the 5 V supply, eliminating a separate negative rail. In a control cabinet, the 24-SSOP package preserves board area, while shutdown and enable controls can reduce interface activity when the equipment is idle.
Recomendado
Data-Acquisition Equipment
The ADM206ARSZ is appropriate for data-acquisition systems that connect a controller to legacy RS-232 instruments. Four driver channels can control multiple peripherals, while three receiver channels collect returned measurements or status data. Its 200 kbps maximum rate is sufficient for many configuration and supervisory protocols rather than high-volume continuous transfers. The single +5 V architecture simplifies instrument power rails, and the approximately ±9 V converter output supplies compliant RS-232 levels without requiring an external negative supply.
Recomendado
Test and Measurement Systems
The ADM206ARSZ can connect laboratory instruments and automated test fixtures to a 5 V control system. The four transmitters support commands for multiple devices, and the three receivers can monitor responses or interlocks. Its 200 kbps maximum signaling rate suits short-distance management and status links commonly found in automated test equipment. The 24-SSOP footprint helps reduce panel-controller board area, while shutdown can be used to place the interface in a lower-power state between test sequences when the host also deasserts the enable signal.
Recomendado
Embedded Control Peripherals
The ADM206ARSZ is useful in embedded controllers that must communicate with older service equipment or external accessories through RS-232. Its logic-level enable and shutdown inputs support firmware-controlled power management and interface reset behavior. The 200 kbps maximum data rate is suitable for command-oriented protocols, configuration downloads, and diagnostic exchanges. Because the device includes the charge-pump converters and accepts 0.1 µF capacitors, an embedded design can obtain RS-232 voltage levels from a 5 V rail without adding a separate negative supply.
Recomendado
Legacy Computer Peripherals
The ADM206ARSZ suits legacy computer and peripheral interfaces that retain RS-232 connectors but no longer use external ±12 V supplies. A modern controller can use the four driver outputs for multiple outbound signals and the three receiver inputs for responses or handshaking lines. The 200 kbps maximum data rate supports many short-distance peripheral protocols. Its surface-mount 24-SSOP package is suitable for replacement and adapter boards where a leaded solution would be unnecessarily large.
Recomendado
Remote Monitoring and Control
The ADM206ARSZ can bridge a remote monitoring controller to RS-232 sensors, actuators, or communication modules that require bipolar signaling. Its multiple drivers support command outputs, while the three receivers support acknowledgements and diagnostic feedback. The device is best suited to moderate-rate, short-distance links because RS-232 communication performance can also depend on cable characteristics, grounding, and protection networks. The integrated converters simplify deployment where only a regulated 5 V supply is available.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ADM206ARSZ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Product Type | RS-232 transceiver |
| Brand | Analog Devices |
| Package | 24-SSOP, 5.30 mm width |
| Number of Drivers | 4 |
| Number of Receivers | 3 |
| Supply Voltage | +5 V |
| Maximum Data Rate | 200 kbps |
| Charge-Pump Capacitor Value | 0.1 µF |
| Converter Output Swing | ±9 V |
| Special Features | Shutdown pin and enable pin |
Principais diferenciais
- Four-driver and three-receiver channel balance (vs MAX3221IPWR)
- Single-rail bipolar voltage generation (vs MAX206CAG)
- Integrated interface power control (vs MAX206CAG)
- 200 kbps maximum signaling rate (vs MAX206EEAG)
Notas de projeto
Place the 0.1 µF charge-pump capacitors directly beside the pins identified in the Analog Devices manufacturer datasheet, observing the required polarity. Keep the associated traces short and provide an unobstructed return path from the device ground. Because the charge-pump nodes switch internally, long traces can increase radiated noise and coupling into nearby measurement or control signals.
Separate the RS-232 connector-side traces from sensitive analog inputs, precision references, and clock signals. The ADM206ARSZ generates approximately ±9 V internally from 5 V, so its switching charge-pump activity must not be routed beneath noise-sensitive nodes. Keep the interface return path continuous and establish where the signal ground meets chassis or system ground according to the complete equipment architecture.
Do not treat every similarly named ADM206 or MAX206 device as a drop-in replacement. ADM206ARZ is associated with a 24-SOIC package, while MAX206CAG and MAX206EEAG lack verified 24-SSOP pin compatibility in the available comparison material. Before substitution, compare package drawings, pin numbers, driver and receiver counts, control functions, supply requirements, and charge-pump capacitor connections.
Use the shutdown and enable controls deliberately to reduce switching activity when the interface is not needed, but ensure the host controller does not expect valid receiver states while shutdown is asserted. For cables extending beyond the equipment enclosure, add the ESD and surge-protection network recommended for the exposed RS-232 connector. The protection devices should be placed near the connector rather than beside the ADM206ARSZ.
Informações de conformidade
The available product information does not provide extractable RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable because the ADM206ARSZ is an industrial/communication interface IC rather than an automotive-qualified device.